Search Documents

By Charles H. Foreman, James F. McCarthy

The orebodies of the Hecla mine are from 3 to 40 ft. wide, dip not less than 70°, and in most cases are nearly vertical. The Hecla and Intermediate orebodies are generally associated with a lamprophyric dike, usually about 2 ft. wide, but which attains a maximum width of 7 ft. The ore appears on either or both sides of the dike. The country rock is Burke quartzite with no definite walls and a tendency for nearly horizontal, but irregular, quartz stringers to run from the lode into the walls. This latter condition prevails almost entirely in the hanging wall, causing a natural tendency for portions of the wall to "offset" and resulting in an extremely heavy side pressure. The fact that there are no definite walls causes a great variation in the width of the stopes, as stringers will run into the walls for irregular distances. The ore occurs as galena in varying widths and grades. It is often necessary to mine a face having a " horse"' of waste between two stringers of ore. This block of waste might be 6 or 7 ft. wide but with the Hecla method it is necessary to mine the entire face. In this case an effort is made only to shatter the waste, allowing for easy sorting underground. The Hecla mine requires a flexible system allowing for the extraction of ore from varying widths, with the necessity of close filling to give the needed protection from side weight. About 15' per cent. of the material broken in the face is sorted as waste, either at the face of stope, or in the sorting plant. Shafts, Drifts and Crosscuts The outside dimensions of the shaft are 19 ft. 4 in. by 7 ft. 2 in. The shaft consists of three working compartments, two for the hoisting of ore and one for auxiliary work. The working compartments are 5 ft. 2 in. by 4 ft. 4 in. inside measurement. The rest of the shaft is used for pump column, electric cables, and ladderway. (See Fig. 6 for framing of timbers.) The shaft is about 700 It. from the orebody for topographical reasons. Solid formation was not reached in shaft for 80 ft. Timbers in this section became alternately wet and dry on account of seasonal changes

Jan 1, 1925

By Henry Hebley

IN preparing this paper it has been the aim of the writer to keep the problems of both producers and consumers in mind. Until now, no attempt has been made to familiarize each group with the other's practice and limitations. This paper is an effort to acquaint the readers with some of the factors pertaining to the problem and cost of mining and preparing steam coal, and also to the economics of producing steam with such coal. In recent years all lines of endeavor have turned to intensive mechani-zation in order to lower the unit cost of production. The average fuel consumption in steam electric generating stations has dropped in 20 years from 4.0 lb. to 1.4.1b. per kilowatt-hour; while the modern power station can generate 1 kw-hr. on a fraction under 1 lb., or 13,000 B.t.u. coal. Also, the amount produced per man has in that same period risen from 3.8 to 8.2 tons, owing to the use of modernized equipment below ground for coal cutting, drilling, shooting, loading, hauling and hoisting. Unfortunately, the rapid speed of 5 tons per minute of operation at which the coal is loaded mechanically precludes any appreciable removal of impurities at the coal face, so that the raw coal is hoisted containing a markedly higher percentage of impurities than the hand-loaded coal, which was subjected to the scrutiny of the miner during loading. Also, during the past 20 years, certain seams of coal lying close to the surface have been made economically available by the improved design of electrically operated shovels and draglines for the removal of overbur-den running as high as 56 ft. This strip coal frequently contains so much ash in the raw state (Table 1) that it would have no sales value. There-fore, coal preparation must be adopted to beneficiate the raw product. Some seams in the United States have a decreasing ash content with decreasing size, owing, in all probability, to the fact that the coal is friable while the impurities are hard, causing a concentration of the low-ash material in the fine sizes. Illinois No. 6 coal being rather hard, naturally the reverse is true.

Jan 1, 1937

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period May 10, 1916 to June 10, 1916: G. Aertsen, Philadelphia, Pa. Hennen Jennings, Washington, D. C. Frederick C. Alsdorf, Wickenburg, Ariz. H. M. LaFollette, LaFollette, Tenn. A. H. Anderson, Worcester, Mass. E. T. Lednum, Chicago, Ill. J. H. Batcheller, Mattapoisett, Mass. Francis Church Lincoln, Reno, Nev. Arthur B. Clark, Sheridan, Mont. H. Mortimer-Lamb, Montreal, Canada. J. Murray Clark, Toronto, Canada. Andrew W. Newberry, San Francisco, Cal. J. H. Collier, Oakland, Cal. C. E. Pettibone, Cleveland, 0. H. S. Emlaw, Spring Lake, Mich. Heinrich Ries, Ithaca, N. Y. E. L. Estabrook, Platteville, Wis. C. S. Robinson, Youngstown, 0. James W. Hambleton, El Paso, Tex. - M. K. Rodgers, Basin, Mont. James Henderson, London, England. E. J. Rossbach, St. Louis, Mo. G. P. Hulst, East Chicago, Ind. J. B. Tyrrell, Toronto, Canada. William F. Jahn, Riebeling, Mont. G. B. Waterhouse, Buffalo, N. Y.

Jan 7, 1916

By P. D. Frost, H. A. Robinson, J. R. Doig, M. W. Mote

The mechanism of hardening in heat-treatable zirconium alloys was foUNd to be analogous to that for titanium alloys. Zirconium containing a relatively large addition of a ß -stabilizing element such as molybdenum or columbium can be hardened by the following transformation: Lean alloys, having insufficient alloy content to retain ß at room temperature are hardened by the following transformation: Application of these findings in Zr-Mo-Sn and Zr-Nb-Sn alloys produced strengths as high as 190,000 psi with reasonable ductility. PRIOR research on zirconium alloys has been concerned with development of greater strengths and creep resistance by solid-solution hardening or by dispersion hardening. Although solution and aging heat treatments had been applied earlier to zirconium alloys, quenching frequently produced low ductility. The possibility that the ß-to-w transformation, discovered earlier in titanium alloys,' might also occur in zirconium alloys and cause low ductility was considered, and, indeed, was found as predicted2 to be the case. In the earliest experiments, the heat-treatment response of titanium, too, was disappointing. However, by avoiding the formation of the embrittling w phase, it became practical to obtain room-temperature strengths higher than 180,000 psi, with elongation values of 10 pct.3 Based on the present concept of titanium heat treatment, the principal requirement for a heat-treatable zirconium alloy is that it contains a certain minimum amount of one or more ß -stabilizing elements. Only molybdenum, columbium, and tantalum, when present in sufficient amounts, are known to stabilize ß zirconium to room temperature during rapid cooling from the ß field. Tantalum was undesirable because of its high thermal-neutron cross section. Aluminum and tin are effective a stabilizers, but aluminum has been shown to seriously decrease the corrosion resistance of simple zirconium alloys in hot water. Therefore, for the present study, tin was used as the stabilizer addition. The alloys selected for this evaluation are presented in Table 1 along with their analyses and ß-transus temperatures. The analyses indicated that intended compositions were usually realized. EXPERIMENTAL PROCEDURES All of the alloys were melted from sponge zirconium and fabricated to sheet for heat treatment

Jan 1, 1960

By C. W. Goodale

I. INTRODUCTION. In the summer of 1909 the Boston & Montana reduction department of the Anaconda Copper Mining Co. completed a new flue system, at a cost of about $1,100,000, and -is this includes the largest and highest chimney in the world, and some new features of flue construction, a description will be of interest. At the Spokane meeting of the Institute in September, 1909, a brief mention was made of this flue system, in discussing Mr. Brunton's presidential paper on the Progress of Metallurgy in the West, and a promise was given that when a long enough time had elapsed, so that operating results could be given, a paper would be offered. The smelting plant includes blast furnaces, MacDougall roasters, gas-fired reverberatories, and converters.

Jan 8, 1913

By W. C. Lilliendahl, H. W. Highriter

THE method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF6) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then pressed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times the uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphite crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO2 in Ascarite, using air instead of oxygen to reduce the temperature and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1).

Jan 1, 1935

By Allan T. Gwathmey, J. Bruce Wagner, Kenneth R. Lawless

Between 250°and 550°C in oxygen pressures of 10 to 760 mm Hg, the relative oxide thicknesses formed per unit time on the (100), (111), (110), and (320), decreased in this order. The predominant oxide orientation was (001)Fe3O4 and [110] Fe304 A small amount of a-Fe2O3 which exhibited a fiber pattern was observed in all oxides except those formed at 250°c in low oxygen pressures. IN order to understand the properties and behavior of thin films, particularly their role in oxidation reactions, there is needed more experimental information on their structure, composition, and kinetics of formation on clean surfaces of known geometry. The present study was undertaken to obtain such information for thin oxide films formed on single crystals of a body centered cubic metal, iron. Crystals in the form of spheres were used in order to expose all possible crystal planes to the reactant gases simultaneously. Using this procedure the relative rates of oxidation of all planes could be estimated, and those exhibiting, maximum or minimum oxidation rates could be selected for a more intensive study of composition and expitaxy. Since the three types of information were obtained from the same experiment using a single crystal substrate, any differences between rate, composition, and expitaxy on the several planes may be attributed to the influence of the substrate structure. EXPERIMENTAL The starting material for this study was Armco iron rods, 6 in. long and 3/8 or 1/2 in. in diam. The analysis was reported to be 99.8 pct Fe, with major impurities listed as carbon 0.018 pct, manganese 0.027 pct, phosphorous 0.005 pct, sulfur 0.029 pct, silicon 0.005 pct, and copper 0.11 pct. These rods were cleaned with ether and heated in an atmosphere of moist hydrogen at 950°C for three days. The purpose of this treatment was to decarburize the iron and to provide a consistent, uniform grain size for the growth of single crystals. Crystals in the form of rods, up to 1/2 in. in diam and 2 in. long, were prepared by a method similar to that reported by Leidheiser and Buck.2 Spherical crystals, 3/8 and 1/2 in. in diam and having a handle about 1/4 in. in diam by 112 in. long, were machined from the single-crystal rods. After machining, each crystal was etched in aqueous nitric acid to remove the cold-worked metal at the surface. Before each experiment, the crystal was polished mechanically with metallographic papers through number 4/0, and electropolished in a perchloric acid-acetic anhydride mixture by the method of Jacquet and Rocquet.3 The crystal was washed in running distilled water for at least 5 min. The excess water was blotted with a soft paper tissue, and the crystal was placed in an all-glass reaction vessel (See Fig. 1). The crystal was heated at 550°C in hydrogen for at least 8 hr prior to the oxidation in order to reduce any surface oxides and to help relieve any stresses in the metal. For the structure and composition studies, flat faces were cut parallel to (loo), (111), and (110) planes on the iron crystal spheres. The orientation of these faces was checked by a back-reflection X-ray diffraction technique. The faces were within 2 deg of the desired orientation. The flat faces were treated as described above except that prior to electropolishing they were given an additional polish on metallographic felt saturated with twenty-minute levigated alumina. After the crystal was heated in hydrogen for at least 8 hr, the temperature was adjusted to the desired value, and the hydrogen was evacuated. Commercial oxygen which had been purified by successively passing through tubes containing magnesium perchlorate, Ascarite and magnesium perchlorate was admitted to the desired pressure as measured by a mercury manometer. A resistance-wound furnace surrounded the oxidation chamber, and a temperature controller maintained the temperature within ±3°C. The furnace was provided with a small window for observing the crystal. The changes in thickness of the oxide films were followed by observing the interference colors. The oxidation was allowed to proceed until the desired oxide thickness was attained on a given crystal plane. The experiment was terminated by evacuating the oxidation

Jan 1, 1962

By M. Kaitz

A continuing discussion in both the petroleum engineering and economic literature is directed to the difficulties encountered in the use of discounted cash flow rate of return (DCF) as a measure of investment worth. Although useful in most Instances, DCF has been criticized because it is time-consuming in its trial-and-error solution, theoretically invalid, not adaptable to cash flow streams yielding multiple return solutions and not entirely reliable in selecting between mutually exclusive investments. The theoretical invalidity of DCF stems from the reinvestment assumption implicit in the calculation that earnings are reinvested at the DCF rate. The emerging consensus of the economic literature is that the net present value or the present worth of the net cash flow stream (discounting at the average opportunity or cost of capital rate) is more correct and reliable. Other criteria proposed have been ratios of net present value divided by initial investment or by present value of all investments in a project. All of these criteria are simple to determine and explicitly assume a reinvestment rate for [he income generated by a project. This paper develops and discusses a theoretically valid profitability criterion which is simple to compute and retains the appeal of a percent return on investment. It is called "percentage gain on investment" or PGI. It measures the gain an investment is expected to realize over like capital invested in the average opportunity and explicitly considers reinvestment potential. Why add another Concept to the large array of investment criteria now available, any one of which, or perhaps a combination of several, appears to embrace the form's (or individuals) objectives? The answer is that not one of the existing criteria provides both a readily comprehensible and theoretically valid measure of risk coverage that has general application. The proposed PGI does fulfill these requirements. INTRODUCTION An ancient expression warns that "one must yield to the times" — there are better ways of doing things. A review of the petroleum engineering and economic literature on one topic alone, measurement of investment worth, certainly is witness to this truth. In use for a number of years, the DCF has recently received attention, directed mainly to its theoretical invalidity. Several alternatives to DCF have been proposed to provide a valid, simply determined criterion to describe investment worth and to overcome the criticisms previously mentioned. This paper introduces another method called percentage gain on investment (PGI) and is proposed as but one of several yardsticks that should be used in making investment decisions. MEASURES OF INVESTMENT WORTH This paper will consider only those criteria which give weight to the time pattern of future earnings. These criteria are usually compared with an average opportunity rate or cost of capital of the firm to judge the relative worth of the investment. For purposes of demonstration, a 9 percent average opportunity rate will be used throughout this paper. Implicit in the DCF calculation is the assumption that earnings are reinvested at the DCF rate. Some argue, though, that there is no reinvestment assumption,' that the DCF rate is simply that maximum rate of interest one can pay on the investment over the life of the project and break even. The determination of DCF is accomplished by discounting the net cash flow stream at that rate (DCF) which will yield zero. The question is: why should reinvestment potential be explicitly considered in calculating return on investment or other criteria measuring economic worth? Perhaps the answer lies in consistent or equal treatment of future cash flow. It appears entirely illogical to give different present worth value to $1 received, say, 10 years from now, which is the circumstance resulting in comparing projects with different DCF returns. In fact, $1 received in 10 years has the same value regardless of which project generated the income. DCF return thus favors investment projects which are expected to provide early income as compared to those providing long-term income. Not surprisingly, the controversy on reinvestment assumption is an old one. Hoskold' discussed this same problem in 1877. He considered the future income from mineral properties as an annuity or a series of fixed future payments. (As will be demonstrated, his equation can be modified for variable income.) Prior to Hoskold, the value or what one could pay for the mine, was determined with the use of standard, single-interest tables. Here is what Hoskold said with regard to these tables. "This table, and others of its kind, to be found in most works on annuities, is constructed correctly according to

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By Wayne Loel

THE application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and under varying climatic conditions, Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarine geology. Aerial photographs with accompanying geologic maps are shown to illus-trate the appearance from the air of different geologic features under varying climatic and topographic conditions.

Jan 1, 1938

By G.A. Moore, C. E. Sims

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By C. E. Sims, G. A. Moore

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By R. Wiesenthal

A method is developed for improving the low recovery efficiency which results when viscous oils are flooded by water. Viscous oil has been diluted with a lighter liquid miscible in it in any ratio which produces a mixture possessing a reduced viscosity and which is then displaced by water. Light gasoline was used in these tests to reduce the viscosity of the oil in place. Oils possessing viscosities in the range of 1.28 to 324 cp at the test temperature of 30C were displaced from a cylindrical unconsolidated sand core, with a length of 2 m (6.6 ft) and a diameter of 10 cm (3.9 in.) at a flood of 6.27 cc/sq cm/hr. In two test series up to I PV of light gasoline was injected into the core before water flooding. In the first series the recovery of a low-viscosity oil (1.28 cp) increased as the volume of light gasoline was increased. However, only the oil which could not be recovered by water flooding alone could be replaced by the light gasoline. In the other series, the recovery of a more viscous oil (13.5 cp) was not increased even if large quantities of light gasoline were injected. An oil bank built up ahead of the water front so that the flood water met with equivalent saturation conditions, as would be the case in flooding solely with water. However, the recovery of more viscous oils could be increased substantially when the core was first flooded with water, followed by a slug of light gasoline, and then flooded with water again. Furthermore, an oil bank ,built up ahead of the second water front. The formation of this oil bank is particularly favorable for the displacement process; the greater part of the light gasoline injected was pushed out of the core ahead of the oil and recovered. Using a light oil of low viscosity, it was possible to replace only the residual oil that could not be recovered by water flooding by the light gasoline. As the basic study had shown that highly viscous oils could be recovered by flooding first with water, then with light gasoline, followed by a second injection of water, the study was extended by tests made with reservoir fluids and cores taken from the low-gravity oil reservoir of the Wietze field, Germany. A great increase in recovery over flooding with water alone was obtained in these tests. The results may show a way to recover high-viscosity oils by a comparatively simple flooding procedure. INTRODUCTION In fields where oil recovery has not benefited from natural water drive, increased recovery may be obtained by the injection of water into the reservoir, especially in the case of fields which produce high-gravity, low-viscosity oil. There is a rather close relation between the viscosity of the reservoir fluid and the recovery that can be obtained by water flooding. As the viscosity increases the oil recovery decreases proportionately, so that an oil viscosity about 30 times that of water is generally considered to be the upper limit for an economically successful water flood.' This limitation has been recognized theoretically by Buckley and Leverett,' and has been verified by numerous laboratory flooding tests, such as by Croes and Schwarz,V n the viscosity ratio range of oil to water from 1 to 500. The reason for the inferior recovery of viscous oils by water flooding can best be understood by considering the mechanism of flood tests. In such tests water is introduced into one end of a sand-packed tube which is saturated with oil of the viscosity to be tested, and oil is produced from, the other end. Oil, with a viscosity lower than that of water, is pushed ahead of the advancing water with considerable uniformity, and irregularities in the displacement process tend to be eliminated as the oil saturation decreases and the water saturation increases. However, oil recovery is not complete, for the water forms interfaces with the oil and traps residual oil droplets in certain of the pore spaces. These residual oil droplets are distributed rather uniformly through the sand, and they are not susceptible to recovery regardless of the amount of water passed through the test cylinder. In the case of an oil possessing a viscosity greater than that of water, the injected water tends to move irregularly through the sand in the test cylinder. At the place in the sand where initial water movement takes place, resistance to the movement of water is lowered and the water finger so formed will grow perceptibly; it will extend to the outlet end of the test cylinder so that a breakthrough of water takes place long before much of the oil-saturated volume of the sand has come in contact with water. Once the breakthrough of water takes place, the water-oil ratio is gradually approaching the economic limit, even though much of the oil in the test cylinder remains unaffected by water. Disconnected drops of oil are trapped in the portion of the sand that has been invaded by water, just as when an oil of low viscosity is flooded. The poor recovery of the more viscous oils, therefore, is due to the irregularity of water movement through the test cylinder, and the rate of water movement through restricted sections of the oil-saturated sand increases with the more viscous oils. There are three ways whereby the recovery of viscous oils by water flooding can be improved:' (1) adding materials which will increase the vis-

Jan 1, 1965

Page Fundamental Principles Involved in Segregation in Alloy Castings. By R. M. Brick. (With discussion)............................* Review of Factors Underlying Segregation in Steel Ingots. By B. M. LarseX.. (With discussion)............................. 4x4 Introduction to the Session on Segregation in Steel. By Earle C. Smith......436 Relation of Open-hearth Practice to Segregation in Rimmed Steel. By J. W. HaLley and G. L. Plimpton, Jr. (With discussion)................438 Segregation in a Large Alloy-steel Ingot. By S. W. Poole and J. .4. Rosa. (With discussion) .............................459

Jan 1, 1945

By Ray W. Arms

DRY cleaning, or pneumatic separation, is not, strictly speaking, a recent discovery. Among the archives of the Patent Office may be found many patents dating back as far as 1850 which cover early attempts to separate materials of varying specific gravity or of different shape by means of air. Hundreds of patents covering this art have been issued, which may be roughly classified into four general groups, as follows: 1. Stationary devices with pulsating air currents. The separating surface is usually riffled and air is supplied by bellows or compressors. This group also includes air jigs, which have been used rather extensively. 2. Stationary devices with continuous air currents. These submitted the material to a continuous current of air, either horizontal or vertical. Chaff is blown from wheat by such a device. 3. Reciprocating or vibrating devices with pulsating air. A small group in which the pulsating air is supplied by bellows and some motion provided in the separating surface to move the stratified material to various discharge points. 4. Reciprocating or vibrating devices with continuous air supply. This is by far the most important group and all recent developments have been along this line. All of the above groups involve the stratification of material by air and include none of the dry methods that use other principles, such as coefficient of friction, magnetism, etc. Air Stratification In all of the above groups of air separating devices, the same phenomena are found as exist in water concentrators; that is, free settling will be found in some and hindered settling in others, with a complex action on the reciprocating tables similar to the wet tables. The experimental value of the settling ratios of particles in air has never been determined but, following the formulas given in Richards'

Jan 1, 1924

By James G. Blaine, David A. Summers, L. John Tyler

There has been a considerable amount of research developed which shows that the close contour cutting of an excavation prior to removal of the central core will increase ground stability while concommitantly, reducing the number and size of blastholes required to create the excavation. To date, the industrial development of this technique has however, centered on the development of equipment based on simple cutter movement and mechanical rock cutting. The advent of reliable field operable high pressure waterjet cutting equipment with the very low reactive force required to hold the head in position has opened the way for a much smaller and more manueverable system. The advent of small, micro-computers allows the programming of accurate profiles for cutting tools on excavation equipment. The combination of these two technologies will allow the generation of complex as well as simple, excavation profiles and lead to the potential pre-support of the opening before major excavation is completed. A brief description of the necessary components and their functions is encorporated in the initial prototype design as given.

Jan 1, 1984

By L. E. Wemple

Previous to 1915, zinc refining had not become a general practice among the zinc smelters in the United States. Such refining as had been carried on was confined chiefly to remelting very high-leaded zinc, such as third-draw metal from the retort furnaces, and slab dross, and hard spelter from galvanizing pots. In this remelting operation, the lead and iron were settled out and the refined spelter obtained graded fifth class, ie., Prime Western. Owing to the presence of lead in most zinc ores, the bulk of the spelter produced by direct smelting is of this Prime Western grade. Careful selection of ores of low lead content gave purer grades of spelter, z.e., Brass Special and Intermediate; and smelters which could secure ores carrying practically no lead produced high-grade spelter. Thus, in general, the grade of spelter produced by any smelter was predetermined by the purity of the ore it could obtain. The needs of the warring nations of Europe for enormous quantities of cartridge and other high-grade brass resulted in such a demand for the purer grades of spelter that the available supply of lead-free and low-lead ores could not produce the quantity required. Prime Western grades went begging, so to speak, while high grades sold at times from 5 to 15 c. per pound over the Prime Western market. The great demand, coupled with the wide market margin, which permitted the inherent costs and losses, resulted in the conversion of the lower grades into higher grades by processes of refining. These conditions also accentuated the development and size of the electrolytic plants, which were being worked out at the time this increased demand for pure grade of metal occurred. The electrolytic process, where available, produces a higher grade of spelter from impure ores than does the fire process; a large portion of those impurities in the ore, which by the distillation process would be carried into the spelter, are removed in the leaching of the ores and the purification of the solutions. The refining process, adopted at a number of smelters for the purpose of converting low-grade spelter into grades suitable for bras4 was that of redistillation.

Jan 1, 1918

By J. H. Westbrook

UNTIL very recently the development of high temperature alloys has been strictly empirical. It is, in fact, a great tribute to the intuition, perseverance, and industry of the practicing metallurgists of this country and abroad that the amazing increases in gas turbine service temperature over the past 15 years have been achieved with so little fundamental knowledge. The result of this development has been the realization of successful but highly complex alloys possessing five, six, or more alloying elements and correspondingly complex microstructures. Within the last few years, considerable effort has been devoted to the identification of the secondary phases in these alloys and to the correlation of the presence or absence of such phases with alloy properties. Little attention, however, has been given the problem of identification of the mechanism (s) by which such phases enhance the properties of the alloy and especially to the assessment of the particular properties of the secondary phase (either in- trinsic or relative to the matrix phase) which are basically responsible for the improvement. Conceivable mechanisms which might apply include dispersion hardening and precipitation hardening. In both cases geometrical factors—particle size, dispersion, volume fraction, etc.—and agglomeration re-

Jan 1, 1958

By E. Lancaster-Jones

THE gravity magnitudes obtained by means of observations with the Eötvös balance in the field are necessarily resultant or total effects due to all abnormalities of mass distribution, including even the effects due to the ellipticity and rotational motion of the whole earth. Since the object of the survey is to isolate the effects which arise solely from some particular subterranean feature, and to deduce therefrom the configuration and extent of this feature, the first step is to eliminate from the observed effects all those due to "disturbing" (i. e., unwanted) features, whether above or below the surface of the ground. The disturbing features have different characteristics, according to their situation relative to the center of the balance and to the horizontal plane through the foot of the balance, or station point; this diversity was recognized by Eötvös, who divided the total effects into so-called Normal, Terrain, Topographical, Cartographical and Subterranean effects. This classification has been adhered to by most subsequent investigators, but the writer prefers to employ the term "three-dimensional," which really indicates the essential character of the class of effect known as "Subterranean," at any rate from the standpoint of the computer of effects. Before disturbing effects can be eliminated, the features must be measured up or surveyed, whether by topographical, mining, or boring methods, and then the effects of each feature calculated and subtracted from-the total observed effects. After this the problem of interpreting the residual effects will itself necessitate the computation of the assumed feature, or even a series of trial features.

Jan 1, 1928