Search Documents

By J. D. Runkie, A. G. Lyle, G. A. Gillies

Tar evaluation of data obtained by selective flotation from even a simple ore is a very difficult process, and when the ore tested is complex the process becomes extremely difficult and cumbersome The authors, in the course of an investigation into the selective behavior of various flotation reagents on nonmetallic minerals§ were confronted with an aggravated form of this difficulty, owing to the large mass of data that had accumulated over a period of years They finally devised a method whereby the results of the various flotation tests could be correlated and interpreted by means of graphs representing recoveries and rejections of the component minerals in the ore This method of graphical analysis proved so useful in nonmetallic flotation that it was afterwards applied to sulphide flotation, where it yielded equally satisfactory results Since this method of analysis leads to very definite conclusions as to the effect of changes in reagents and flotation procedure, it is felt that a wider application of the method might assist the industry by reducing the amount of test work required, and possibly increase the accuracy of the final analysis GRAPHS In Fig I, four curves are plotted on the same graph with cumulative percentages as ordinates and cumulative weights as abscissas In this instance the four curves are named, respectively the barite-recovery curve, the limestone-rejection curve, the silica-rejection curve, and the summation curve In these tests barite was the mineral concentrated, therefore a barite concentrate was produced Definitions Before explaining the curves in detail it might be advisable to define several new terms, such as "percentage rejection," "summation index," and "summation curve," as well as the word "test," which has been used in a special sense. A "test" will include all the operations performed upon a batch of ore from the time it is placed in the rod mill until the last product has been assayed Thus a test may be a comparatively simple procedure producing only one concentrate and a tailing, or it may be a very complicated procedure producing five or more concentrates of a specific mineral as well as a tailing The number of concentrates produced will depend entirely upon whether the collector was added to the pulp in the flotation cell in one lot or was added in five or more portions Percentage Rejection-The ability of a selective flotation collector to reject an undesired mineral is just as important as its ability to collect the desired mineral The percentage rejection curves shown on the graphs give this factor due consideration and its value is calculated as follows Suppose a concentrate contains 5 per cent of an undesired mineral This indicates

Jan 1, 1942

By F. Wald, A. J. Rosenberg

The general features of the constitution of the B-Pt system were determined using standard rnetal-lograph~c, thermoanalytic, and X-ray diffraction techniques. Three compound were found. Two of these, Pt3B and Pt,B, are formed by peritectic reactions at 523° and 890°C, respectively. The third, Pt3B,, is congruently melting with a flat maximum at 940°C but decomposes eutectoidally in to Pt,B ant1 boron nt - 600° to 650°C. THE low-temperature allomorph of boron (red, simple rhombohedra1 a boron) is of scientific and technological interest as an elemental semiconductor.' However, the studies of this material have been hampered by its reported instability above 1200"~ which precludes crystal growth from the melt (mp - 2200°C). Crystallization from platinum solutions has been suggested as an alternative crystal-growth technique, but has met with only limited success.' The technique depends upon the existence of a significant difference between the eutectic temperature and the transformation temperature of boron. In order to clarify the conditions for further crystal-growth experiments, we found it desirable to redetermine the main features of the B-Pt phase diagram since previous reports on the system1'5'6'7 are in marked disagreement. EXPERIMENTAL The experimental methods used were thermal analysis, metallography, X-ray analysis, and, to a lesser extent, measurements of microhardness. Most of the alloys were prepared from spectrograph-ically standardized boron obtained from Johnson-Matthey &Co., Ltd. (212 ppm impurities, exclusive of carbon and oxygen) and platinum powder obtained from F. Bishop & Co. (200 ppm impurities, mainly of other platinum group metals). Some alloys were also prepared with very high-purity, float-zone refined boron (99.9999 pct obtained from "Wacker Chemie" and extrahigh-purity platinum (99.999 pct) obtained from Johnson-Matthey & Co., Ltd. The reported results did not depend on the choices of these starting materials. Five-gram alloy specimens containing 10, 20, 25, 27.5, 30, 33.3, 34, 35, 37, 37.5, 38, 39, 40, 41, 42, 43, 45, 50, 55, 60, 70, and 80 at. pct B were made by melting the elements together in boron nitride crucibles using rf heating of a graphite susceptor, either in vacuum or under high-purity argon. All alloys were heated to at least 1800°C for -5 to 15 min. Most of the alloys did not wet the crucibles when the latter were outgassed by preheating under vacuum. In any event, no weight loss was detected after melting, and the nominal composition was assumed for all specimens. Thermal analysis on 2.5-g samples were carried out in boron-nitride crucibles under a vacuum of 5 x X torr. The apparatus was heated in a "Kan-thal A 1" wound furnace, which limited the maximum temperature to about 1100°C. The output of the indicator thermocouple was fed to a dc recorder with a 1-mv full-scale span and an adjustable zero. The apparatus was calibrated repeatedly, using the freezing points of high-purity aluminum, silver, and gold. The results justified the use of the NBS voltage vs temperature tables for Pt/Pt 10 pct Rh thermocouples. All thermal analyses were run at least twice and both the heating and cooling effects were recorded. Most of the alloys had a very strong tendency to supercool. However, the use of mechanical vibration permitted reproducibility within *5°C for all alloys, except in the region around 40 at. pct B. Only the cooling effects are plotted in Fig. 2, since they appear to be more reliable. For metallography, the alloys were cut with a diamond cutting wheel, cast in a polymethacrylate resin, ground and polished with diamond paste, and etched with dilute aqua regia, a common etch for platinum alloys. Both copper and molybdenum radiation were employed to obtain X-ray diffraction data using Debye-Scherrer cameras and a "Norelco" diffractometer Diffractometry with high scanning speeds (1 deg per min) using nickel filtered CuK, radiation was used to identify the main regions of the diagram. However, molybdenum radiation was used for the detection of boron, since the latter showed very strong absorption and fluorescence effects with CuK, radiation. RESULTS AND DISCUSSION Three intermediate compounds, corresponding to the compositions Pt3B, Pt2B, and Pt3B2, were found in the system. Fig. 1 reproduces their X-ray diffraction spectra, together with those of pure boron and pure platinum. As can be seen from the thermal-analysis data in Fig. 2, Pt3B and Pt2B are formed by

Jan 1, 1965

AT the meeting of the Board of Directors held on June 25, 1926, and in response to numerous in-dividual suggestions for changes, a committee on Re-vision of the Constitution and By-Laws of the Insti-tute was appointed, consisting of C. F. Rand, Archi-bald Douglas and H. Foster Bain. Various confer-ences were held, much correspondence conducted and a preliminary draft was prepared. It proved imprac-ticable to complete the work in time to submit the matter to the membership for approval or disapproval at the annual meeting in 1927, and the Committee was continued with instructions to prepare a report as a basis of action in 1928. After Mr. Rand's death George Otis Smith was appointed in his place and the tentative draft herewith submitted has been pre-pared in its present form by Messrs. Smith, Douglas and Bain, though not differing in any material mat-ter from an earlier draft approved by Mr. Rand. In preparing this the Committee has kept in mind primarily the desirability of simplification and of making the By-Laws conform to the actual practice of the Institute as worked out through experience. The Constitution and By-Laws adopted in 1912, and which with minor amendments only still govern the Insti-tute, are full of specific provisions regarding pro-cedure; such as that laid down for guidance of the Papers and Publications Committee. Many of these have proved unworkable and in practice have not been always strictly followed. It now seems wise to write into the Constitution and By-Laws only the general fun-damental principles to he followed and to provide for such easy change in methods of following them out as will permit efficient conduct of the business. It is this thought that has guided the Committee in rewrit-ing many of the sections. With this in view also the Constitution, as such, has been shortened to the brief-est feasible statement of fundamentals. All matters relating to means of making these principles effec-tive have been put into the By-Laws or in the hands of committees whose work is subject to control and whose rules are subject to approval or disapproval by the Board of Directors. Many suggestions for changes have come to the Committee that have not been incorporated in this draft. Some of these are in themselves excellent but have not been incorporated here because the Commit-tee discovered no sentiment for them such as would be likely to secure their approval, or found them out of harmony with the general plan followed herein.

Jan 9, 1927

By Sidney Powers

CONTENTS PAGE Distribution of fields 4 History of development 6 Origin of oil 7 Structure,, accumulation and migration 8 Reservoir rocks 9 Methods of drilling and exploration to Oil-field statistics 12 Description by regions: United States: Appalachian region 12 East-central states 17 Kansas 18 Oklahoma 19 Texas 24 Arkansas 32 Louisiana 33 Mississippi -.. 34 Rocky Mountain region 34 California : 37 Canada 41 Mexico 43 Cuba 46 Bibliography 46 THE purpose of this brief account of the occurrence of petroleum in North America is to make available to those who have a knowledge of geology, but who are not engaged in the petroleum industry, a few salient facts about the location of oil and gas fields, their productivity, the important structural types of accumulation and the age of the rocks containing petroleum. A few useful data and statistics are furnished, yet not complete statistics that are available elsewhere. Geology has been treated in simple terms because the reader is presumed to have little interest in the names of formations and of oil sands. Mineral deposits are more or less analogous. Whether oil or metals, minerals are found in rocks, largely in sedimentary rocks which carry water or have at one time carried it. A genetic or accumula-

Jan 1, 1931

By A. R. Kaufman, P. Gordon

THE large-scale manufacture and use of uranium in conjunction with the atomic energy development during the war led to a need for knowing the equilibrium diagrams of uranium with various other metals. The alloys of uranium with aluminum and with iron were among the first that were studied for this purpose. Much of the work was done in the manner of a survey since it was necessary to determine the important features of the phase diagrams rather than to obtain completely detailed results. For this reason no attempt was made to locate exactly such features as liquidus lines, solid solubility limits and compound and eutectic compositions. It is believed, however, that there are no great inaccuracies in the diagrams reported here and that no important points were overlooked. Earlier work on alloys of uranium with aluminum and iron is almost nonexistent and in each case is considered to have been of little value by M. Hansen. It is interesting to note, however, that the compound UAl3 was first reported in 1902 by L. Guillet. Experimental Procedure Materials: The uranium used for making most of the aluminum alloys was obtained from material prepared by Metal Hydrides, Inc., and melted in vacuum at M.I.T. Because of the lack of an adequate supply of metal, it was necessary to use material from several different batches and hence it is impossible to state an exact analysis. However, a few results indicated about 0.01 to 0.03 pct iron and probably about 0.03 to 0.05 pct carbon. Toward the end of the work a small amount of metal was obtained from Brown University and from Iowa State College and this was used in determining the transformations in pure metal and in some dilute alloys. All of the aluminum used in this investigation came from a supply of high purity metal (greater than 99.9 pct aluminum) which was obtained through the courtesy of Dr. Mehl of the Carnegie Institute of Technology. The uranium used for making the alloys with iron was produced by the bomb reduction process which has been described by J. Chipman.² This metal, after vacuum melting, contained about 99.9 pct uranium by weight with carbon and iron as the chief impurities. Electrolytic iron containing about 0.012 pct carbon, 0.020 pct nickel and 0.009 pct copper was used in making the melts. Melting Equipment: The melting of the alloys went through a stage of development which culminated in the use of beryllia or beryllia-lined crucibles and in the use of high frequency heating in either vacuum or in an atmosphere of argon. It was found that uranium at a few hundred degrees above its melting point would pick up aluminum and to a lesser extent silicon from an alundum thimble while aluminum above 1000°C would extract silicon from the impure alundum. No reaction of either metal with beryllia was noted at temperatures as high as 1800°C. The distillation of aluminum from the aluminum-rich alloys was quite troublesome at temperatures above about 1300°C and was only partially avoided by the use of argon instead of vacuum. Melting in resistance furnaces,

Jan 1, 1951

By AIME AIME

DATA in this report enable comparisons to be made within the bituminous coal industry and comparison as well with copper and steel in respect to capacity and overdevelopment. The conclusions reached from the data will tend to correct numerous current misconceptions. The data have been prepared by various members of the Coal and Coke Committee of the A.I.M.E., from the most authentic sources avail¬able, and cover the period 1913-1924 wherever possible. CAPACITY AND OVERDEVELOPMENT Table 1 shows statistics for the industry, mainly from the U. S. Geological Survey sources, but partly from the U. S. Coal Commission reports. The mine capacity with equipment and labor as of given date is calculated for each state by obtaining the total man days worked as reported by the operators, and dividing this figure into the total production, getting the production per man day; this figure times the number of men employed times 308 (a theoretical full working year) equals estimated full-time capacity. Two major objections are made to this method-one that the total number of men employed is used instead of the number actually working, and the other that the number of days used only deducts Sundays and five holidays. Covering the first, the same number of men is used in estimating capacity as is used in actual production, and this condition exists at all times. Regarding the second, the opinion is general among coal men that 280 days is as great a figure as should be used, as it is practically impossible to keep any mine working full time at the same daily rate as when it is working part time. The capacity, as estimated on this basis, is much more nearly the true capacity, although even with present railroad efficiency this amount of coal could not be moved.

Jan 1, 1926

By J. H. Nead

The experiments herein described were undertaken with a view to investigating thoroughly the influence of carbon on the tensile and impact physical properties of carbon steel. The original comprehensive plan included investigation of a series of steels with varying carbon contents over a wide range of heat treatments. These were to be studied as to their static tensile qualities, and also their resistance to shock as measured by the Charpy impact bending test. A thorough metallographic examination was likewise included in the schedule. The Charpy tests and the metallographic examination have not been completed to date, and are accordingly withheld for another report. All heat treatments, however, have been made, and the static tensile tests have been completed. A description of the procedure of the experiment and the results thus far obtained are therefore reported herein. Conclusions No attempt is made to draw general conclusions from these experiments, but the curves and the data are submitted as being of general importance and wide applicability. Composition of Materials An attempt was made to secure steels increasing in carbon by increments of 0.1 per cent. from 0.1 per cent. up to 0.8 per cent., and from that composition to 1.6 per cent. by increments of 0.2 per cent. Actually, however, steels of the composition given in Table I were procured, and as the carbon contents were arranged sufficiently well so that satisfactory curves could be drawn showing the relation between carbon content and other properties, these steels were used in the experiments.

Jan 1, 1916

By F. L. Wolf, G. E. Alderson

The reclaiming of nietallics from slag and sweepings is of vital interest to every brass-foundry man, but the first cost and interest on the investment often make it prohibitive for the small foundry to enjoy the benefits of a complete concentrating unit. However, the cost of such an installation and the cost of operation are often exaggerated to such an extent that foundries dispose of their copper-bearing refuse at a great loss. This paper gives the actual costs and the returns obtained in the reclaiming plant used at the Ohio Brass Co. This plant is divided into two sections—the preliminary treatment and concentrating departments. In the former occur the screening, crushing, and hand-picking operations whereby rnost of the non-valuable and heavy metallic constituents are removed. The concentrating equipment consists of an elevator, bins, jigs, ball-mill, arid table. Preliminary Treatment The preliminary treatment varies, depending on whether the material is slag, foundry-floor sweepings, or brass casting-floor sweepings. Material of the first class is produced from the operation of six Steele-Harvey and six Schwartz furnaces; the second class represents sweepings from an average of thirty-five. molding floors per day: and the last is collected around the sprue cutters and knockout bench. Treatment of Slag The slag, analyzing 30 to 40 per cent. copper, is passed over a 3-mesh yard screen (Tyler standard mesh) stretched on an inclined rectangular frame supported by adjustable legs and equipped with a hopper which directs the undersize into a barrow. The fine product, running about 20 per cent. copper and representing 20 to 25 per cent. of the total slag, goes direct to a storage bin for concentrator frrd. The oversize is charged into a No. 2 Hill cinder crusher, which takes 175 to 200 11,. to a charge and crushes two charges per hour through 'a No. 4 riddle. It

Jan 1, 1921

By Charles C. Russell, Glenn C. South

A primary factor in the selection of coals for making coke at high temperatures is the amount of pressure the coal will exert upon the oven walls when carbonized in modem by-product ovens.l-3 This factor has become increasingly important in recent years because of demands for increased throughput and higher coke yields. As a result of the increasing necessity for assessing coals in regard to their carbonization pressures, more and more research work is being directed toward developing labora-tory-scale tests for predicting carbonization pressures and for showing how blends of coking coals may be modified to eliminate pressures liable to damage coke-oven walls. The specific reasons have never been defined as to why some blends of coking coals develop dangerous carbonization pressures and others do not, therefore specific procedures to eliminate dangerous pressures could not be prescribed. It is true that the major processes occurring during carbonization have been described by many writers,4 and there is a general agreement on the ideas of the changes that occur as coal is transformed into coke. However, there is little evidence relating the processes occurring during carbonization to the pressure developed and the available evidence is very incomplete and often contradictory. This deficiency arises in part from the fact that the fundamental causes of pressure development have not been defined, at least from experimental data, and in turn this is the result of the lack of satisfactory testing equipment for studying the problem. Operating experience has shown several ways of reducing or eliminating dangerous pressures,5 but probably none of these ways is applicable to all blends of coking coals, and such empirical methods often lead to production of inferior coke. They are trial-and-error methods, not designed to remedy specific causes of pressure development. The number of laboratory-scale testing devices designed to estimate the carbonization pressures that result when coals are carbonized in commercial ovens is probably well over a hundred.6 Few of these instruments have remained in use for any length of time, either because the predictions were not sufficiently accurate or, more often, because too many exceptions were found. Often testing devices are operated without any attempt at duplication of conditions in commercial ovens and erroneous and contradictory results are frequently obtained. Therefore, it has seemed desirable to study the properties of coal itself and to determine any relationships between the properties of the coal and the carbonization pressures developed. Relationship between Properties of Coal and Carbonization Pressure Attempts to determine relationships between various properties of coal and carbonization pressures, for the most parti have been indirect because no satisfactory and reliable laboratory testing device has

Jan 1, 1944

By Glenn C. South, Charles C. Russell

A primary factor in the selection of coals for making coke at high temperatures is the amount of pressure the coal will exert upon the oven walls when carbonized in modem by-product ovens.l-3 This factor has become increasingly important in recent years because of demands for increased throughput and higher coke yields. As a result of the increasing necessity for assessing coals in regard to their carbonization pressures, more and more research work is being directed toward developing labora-tory-scale tests for predicting carbonization pressures and for showing how blends of coking coals may be modified to eliminate pressures liable to damage coke-oven walls. The specific reasons have never been defined as to why some blends of coking coals develop dangerous carbonization pressures and others do not, therefore specific procedures to eliminate dangerous pressures could not be prescribed. It is true that the major processes occurring during carbonization have been described by many writers,4 and there is a general agreement on the ideas of the changes that occur as coal is transformed into coke. However, there is little evidence relating the processes occurring during carbonization to the pressure developed and the available evidence is very incomplete and often contradictory. This deficiency arises in part from the fact that the fundamental causes of pressure development have not been defined, at least from experimental data, and in turn this is the result of the lack of satisfactory testing equipment for studying the problem. Operating experience has shown several ways of reducing or eliminating dangerous pressures,5 but probably none of these ways is applicable to all blends of coking coals, and such empirical methods often lead to production of inferior coke. They are trial-and-error methods, not designed to remedy specific causes of pressure development. The number of laboratory-scale testing devices designed to estimate the carbonization pressures that result when coals are carbonized in commercial ovens is probably well over a hundred.6 Few of these instruments have remained in use for any length of time, either because the predictions were not sufficiently accurate or, more often, because too many exceptions were found. Often testing devices are operated without any attempt at duplication of conditions in commercial ovens and erroneous and contradictory results are frequently obtained. Therefore, it has seemed desirable to study the properties of coal itself and to determine any relationships between the properties of the coal and the carbonization pressures developed. Relationship between Properties of Coal and Carbonization Pressure Attempts to determine relationships between various properties of coal and carbonization pressures, for the most parti have been indirect because no satisfactory and reliable laboratory testing device has

Jan 1, 1944

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

[Note.—The paper of Mr. Hoffman on " Practical Results in the Magnetic Concentration of Iron-Ore " (page 602); that of Mr. Langdon on "The Use of Magnetic Concentrates in the Port Henry Blast-Furnaaces" (page 599); and those of Mr. Landis on "The Determination of Iron in the Tails from Magnetic Concentration " (page 609) and "Note on Sampling Iron-Ore" (page 611), were all prepared as contributions to this discussion.] The papers of Mr. Langdon and Mr. Hoffman were presented. W. H. Hoffman, Croton Mines, N. Y.: I will add a few remarks, by way of answer to inquiries for further details. The Croton Mines are particularly well located for cheap mining. The ore-bed is very large, and so lies in relation to the railway tracks of the Harlem and other railroads that a very large proportion of our mining for several years to come can be done above these tracks. The concentrating-mill is now 400 feet from where we are working in the quarry. In blasting we never remove less than 2500 tons at a blast,

Jan 1, 1892

By G. P. Boomslitter

In previous discussions on stresses in hoisting ropes, little has been said concerning the effect of the elasticity of the rope itself on the stresses due to acceleration. Laschinger1 has calculated acceleration stresses for several cases but he has ignored the elasticity of the rope as a factor, except as it compresses the drum and stretches itself as it winds thereon. He also deals with steam plants and he shows the effect of the "jerky" start of the engine. This effect would actually be reduced by the elasticity of the cable. With the advent of the motor-driven hoist, new conditions have arisen. The jerk mentioned by Laschinger has been eliminated and smoother starting made possible. But the elastic properties of the rope seem to introduce considerable periodic acceleration stresses in the rope. The following discussion of acceleration stresses is based on the assumption of a constant acceleration at the drum. To be exact, the mathematical work is based upon the assumption that the top is moving upward with a constant acceleration, and ignores the fact that the cable is shortening as it winds. However, the effect of the shortening would be inconsiderable during the first part of the acceleration period. Most hoisting engineers make the assumption of constant acceleration at the drum. Under the older method of calculating acceleration stresses, this would be true with a constant torque motor. But if stresses vary, as this paper attempts to show that they do, constant torque would not give constant acceleration, although the velocity-time curves obtained in the full size test herein described showed that they approach rather closely to this condition, at least as nearly as could be measured. Theoretical Discussion According to elementary physics, the force required to accelerate a Wf body of weight W at the rate of f ft. per sec.2 is wf . To raise the body Wf with acceleration of f ft. per see.2 the total force required is I + Wf, in if

Jan 1, 1927

By A. C. Bulnes

This paper applies the methods of statistical analysis to the interpretation of core analysis data of dolomitic limestone from the San Andres formation at Wasson and the Clearfork formation at Fullerton. Probability relationships are shown to connect the porosity and the permeability and the porosity and the fluid saturation. For example, the porosity-permeability relationship expresses the probability that a sample of porosity,f, will or will not be permeable. The over-all porosity frequency distribution of the reservoir together with the frequency curves of permeability (one for each class interval of porosity) provide a precise basis for computing the weighted average productive porosity of the reservoir for any assigned value of the minimum productive permeability. The probability that the permeability of a core specimen from Fullerton will exceed a given value appears to be dependent on the percentage porosity of the specimen, its void structure type (i.e., porosity in the qualitative sense), and the given value of the permeability. If continuous profiles of void structure type and porosity are available together with the appropriate porosity-probability of permability plots, the nes pay thickness may be estimated. The Invasion Index of a well is defined in terms of the porosity and permeability data. This index is suggested as a basis for comparing wells as regards their suitability as fluid-injection wells. Three problems of importance in the exploitation of limestone reservoirs may be stated as follows: 1. The determination of the productive porosity of the reservoir. The productive porosity is defined as f = fPVP/V [II in which Vp, is the volume of the reservoir that is sufficiently permeable to oil to give up an appreciable fraction of its original oil in place during the economic life of the reservoir; fp, is the arithmetic mean porosity of the permeable volume v*, and V is the total volume of the reservoir. 2. The determination of the number of feet of oil-bearing porous rock that will produce at a commercial rate into the well bore; i.e., the net pay thickness. 3. The choice of fluid-injection wells in a secondary recovery program. The ultimate recovery of the reservoir is proportiona1 to the productive porosity. The productive capacity of the well is proportional to the net pay thickness. The principal purpose of this paper is to show that the methods of statistical analysis when applied to core analysis data of dolomitic limestones offer a useful approach to the solution of these three problems, as well as others of importance in reservoir engineering. The use of these methods was suggested by the work of Jan Law.1

Jan 1, 1946

By A. C. Bulnes

This paper applies the methods of statistical analysis to the interpretation of core analysis data of dolomitic limestone from the San Andres formation at Wasson and the Clearfork formation at Fullerton. Probability relationships are shown to connect the porosity and the permeability and the porosity and the fluid saturation. For example, the porosity-permeability relationship expresses the probability that a sample of porosity,f, will or will not be permeable. The over-all porosity frequency distribution of the reservoir together with the frequency curves of permeability (one for each class interval of porosity) provide a precise basis for computing the weighted average productive porosity of the reservoir for any assigned value of the minimum productive permeability. The probability that the permeability of a core specimen from Fullerton will exceed a given value appears to be dependent on the percentage porosity of the specimen, its void structure type (i.e., porosity in the qualitative sense), and the given value of the permeability. If continuous profiles of void structure type and porosity are available together with the appropriate porosity-probability of permability plots, the nes pay thickness may be estimated. The Invasion Index of a well is defined in terms of the porosity and permeability data. This index is suggested as a basis for comparing wells as regards their suitability as fluid-injection wells. Three problems of importance in the exploitation of limestone reservoirs may be stated as follows: 1. The determination of the productive porosity of the reservoir. The productive porosity is defined as f = fPVP/V [II in which Vp, is the volume of the reservoir that is sufficiently permeable to oil to give up an appreciable fraction of its original oil in place during the economic life of the reservoir; fp, is the arithmetic mean porosity of the permeable volume v*, and V is the total volume of the reservoir. 2. The determination of the number of feet of oil-bearing porous rock that will produce at a commercial rate into the well bore; i.e., the net pay thickness. 3. The choice of fluid-injection wells in a secondary recovery program. The ultimate recovery of the reservoir is proportiona1 to the productive porosity. The productive capacity of the well is proportional to the net pay thickness. The principal purpose of this paper is to show that the methods of statistical analysis when applied to core analysis data of dolomitic limestones offer a useful approach to the solution of these three problems, as well as others of importance in reservoir engineering. The use of these methods was suggested by the work of Jan Law.1

Jan 1, 1946

By Charles D. Borror, George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By George K. Foster, Charles D. Borror

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By Walter H. Bruckner, George B. Clark

SINCE the end of World War II interest has been increasing in the use of shaped charges in the mining industry and in other industries using explosives for blasting purposes. Shaped charges employ the principle known as the "Munroe effect," which was discovered by Charles E. Munroe more than 50 years ago (in 1888). Details of their design have been explained e1sewhere.l,2,3 Fig I shows the essential features of design of two types of shaped charges (with conical and hemispherical cavities) and a schematic sketch of their action upon detonation. The following discussion deals with the behavior of the metal in the cavity liners when they are subjected to intense pressures exerted when the explosive charge is detonated. Among the conclusions reached in research on shaped explosive charges, the following have been established concerning cavity liners: 1,2 I. The optimum wall thickness of a conical cavity liner is dependent upon the apex angle of the cone as well as on the base diameter of the charge. Acute apex angles require thinner walls for optimum performance and more obtuse angles require thicker walls for the same base diameter. 2. Cones were more effective in forming a penetrating jet when the walls were tapered; i.e., the thickness of the wall of the cone increased from the apex down. 3. The physical and mechanical proper- ties of metals have a marked effect upon their performance as cavity-liner material. Boiling point, ductility, malleability, tensile strength, and hardness are among the properties that influence the effectiveness of a metal used as a cavity liner. Lead, for example, makes a wide, flat crater in steel plates. Aluminum makes a deeper crater than lead, and an aluminum alloy having a high tensile strength makes a deeper hole, but slightly smaller in diameter. Cast iron makes a deep, narrow hole. These findings, together with the following analysis under Metallographic Survey of Slug, offer solutions to many of the problems involved in solving the mechanism of the formation of Munroe jets. It has been fairly well established that cavity liners collapse in a manner similar to that indicated in Fig 2. Conical liners are known to collapse upon themselves while hemispherical liners are believed to turn inside out in the process of jet formation. The first has been definitely proved by recovery of collapsed portions of cones, while liners from partly detonated charges show that hemispheres may turn inside out. Fig 3 shows a sketch of a recovered slug from a 6-in. shaped charge using a 45° cone made of cast iron. (This size of charge drilled holes up to 3 ft in depth in solid granodiorite.)

Jan 1, 1947