Search Documents

By E. P. Klier, Taylor Lyman

The structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davcnport and Bain.' Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etchingl acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can he formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypo-eutectoid steels. Mechanism OF Bainite Formation Davenport and Bainl considered the mechanism of bainite formation to consist of two steps—an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide palticles, (not lamellae), at a rate depending upon temperature In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipi. tation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By S. Leber, R. F. Hehemann

This investigation describes the kinetics of alloying in a (Cb-15 wt pct W. 5 wt pct Mo, 1 wt pct Zr) powder-metallurgy alloy. The degree of homogeneity obtained in hydrostatic ally pressed and vacuum-sintered samples is described by composition distributions resulting from analysis of X-ray dvfraction line profiles. Sintering variables and degvee of powder dispersion were evaluated. The utility of single-value parameters obtained from composition distributions is disaissed. The spatial distribution of composition, as revealed by anodically tinted metallographic sarrzples, was used to provide diffision models based on a concentric-sphere geometry. Diffusion equations developed from these models were found to be in general agreement with experimental results. The powder-metallurgy method for the production of refractory metal alloys has the ability to produce an inherently fine-grained, fabricable structure. The more general use of this method is inhibited, in part, by the presumed difficulty in obtaining homogeneity on a microscale. The degree of homogeneity therefore is an important, but usually neglected, variable in specifying the quality of a powder-metallurgy alloy. Convenient techniques for measuring the degree of homogeneity are now available,' and have been used to develop a model describing the process of alloying in a simple binary mixture.' In this investigation, the process of alloy formation has been studied in a more complex system. PROCEDURE The columbium-based F-48 mixture was prepared from the constituent powders shown in Table I. The particle sizes tabulated were provided by the vendors of the individual powders. Standard laboratory techniques utilizing a jar mill were employed for blending. The blended powders were hydro-pressed into 1-in. diam rods which were then sliced into thin discs for vacuum sintering. All samples were given a preliminary treatment at 1700°C for 2 hr. Varying degrees of homogeneity were obtained using additional treatments at higher temperatures. The degree of homogeneity obtained by a specific sintering treatment was evaluated metallographi-cally using the anodic-tinting technique described by olff,' and quantitatively by the analysis of X-ray diffraction line profiles using the X-ray diffraction technique developed by udman.' The diffraction technique is strictly valid only for binary systems. However, the relatively small difference between the lattice parameters of tungsten and molvbdenum when compared with columbium permitted the treatment of the complex composition of F-48 as a (W, Mo)-Cb pseudobinary. Calculations were weighted in accord with the W-Mo ratio in the F-48 composition. The contribution of the 1 pct Zr was ignored since it could not even be detected in the blended powder. Two factors are required to convert an X-ray line profile into a composition distribution. The variation of these factors with composition is shown in Fig. 1. Curve A was used to convert angular posi-

Jan 1, 1964

By F. R. Hensel

PURE silver and silver-lead alloys have been studied as to their suitability for bearings.1-8 A review of the properties of thallium and the silver-thallium constitutional diagram was made by the author to analyze the possibilities of silver-thallium compositions for antifriction materials.† The silver-rich end of the diagram as reported in the literature9-11 was found to be sketchy and it was necessary to carry out considerable experimental work to arrive at definite conclusions. Some of the results of this work are reported in this paper. TEST MATERIALS In the beginning of the work, only fused alloys were investigated. Later, research [TABLE I. Composition of Fused Silver thallium Alloys Tested for Antifriction Properties PERCENTAGE ALLOY No.OF THALLIUM 15330.48 153406 231 HT2.04 2312.10 232 HT3.83Balance 2324.07Silver 233 HT5.86 2336.38 2349.84 234 HT10.07] was carried out on electroplating methods and diffusion processes. In preparing the fused alloys, care was taken to exhaust the toxic fumes caused by the thallium content. The compositions of the series of fused alloys are listed in Table I. The silver-thallium alloys were melted in clay-graphite crucibles and cast into preheated steel molds of 3/4-in. diameter. In the cast condition, they showed a cored structure, as indicated by the micrographs of Figs. I to 3. The etching reagent used was a mixture of 2 grams K2Cr2O7, 8 c.c. H2SO4, and 100 c.c. H2O. The cored structure is unsatisfactory for the type of corrosion resistance required for bearing applications, and homogenizing experiments were carried out at various temperatures, the results of which are shown in Figs. 4 through 8. The alloys with a lower thallium concentration, which were heated for 2 hr. at 525°C. show an almost completely homogenized solid solution type of structure. With higher thallium concentration, the homogenizing temperature was dropped to 475°C. to eliminate the formation of a liquid phase. It is evident that heating for 2 hr. at this temperature did not result in complete elimination of the cored structure. As would be expected, cold-working of the cast structure is an expedient in establishing equilibrium conditions. The fine homogeneous grain structure shown in Fig. 7 corresponds to the cold-worked area under the Rockwell ball penetration when the hardness was taken before heat-treatment. A detailed structural study was made on a cast silver-thallium alloy containing 3.67 per cent thallium. Three micrographs (Figs. 9, 10 and 11) show the transition

Jan 1, 1945

By W. P. Sykes

ThiS investigation was undertaken primarily to establish the relations existing between temperature and mechanical properties in molybdenum, nickel, and an aluminum-copper alloy. Mlolybdenutn (m.p. 2500" C.) was chosen because it is partly similar to tungsten and partly similar to the common ductile metals. Also it is known to furnish, by proper treatment, a desirable material to use in studying relation of grain size and physical properties. The molybdenum used was of the quality that is drawn into wire 0.003 in. in diameter for use as filament supports in incandescent lamps; Chemical analysis shows less than 0.1 per cent. of impurities. Nickel belongs to the same class as iron. Its melting point is 1450" C. and an allotropic change at about 370" C. results in a loss of magnetism above that temperature. This feature made nickel doubly valuable for the purposes of these tests. The nickel used was obtained from the Driver-Harris Co. as 0.090 in. (2.3-mm.) wire, annealed; analysis showed 99.8 per cent. nickel and 0.150 per ccnt. iron. Aluminum is one of the low melting-point metals. Some tensile tests at clevated temperatures have been reported by Bengough but the possibility of learning more with the low temperature and sensitive apparatus available rccommendcd this metal. The samples marked A1 arc an aluminum-copper alloy that contains 3 per cent. copper, 0.42 per cent. iron, and 0.21 per cent. silicon. The presence of the copper somewhat coniplicates the analysis of the results; but the action of copper in aluminum has been studied so that its influence might have been foretold, in part at least. The material and analyses were furnished by the Aluminum Castings Co. The nickel wire, which was deformed at 400" C., was drawn under a bath of molten lead and through a die, which also was immersed in the bath. A thermocouple was suspended in the molten metal to indicate the temperature. Hot oil was uscd as the heating bath for drawing the

Jan 1, 1921

By W. P. Sykes

SEVEN years ago, Dr. S. L. Hoyt1 presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned.

Jan 1, 1938

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

By L. N. Brown

The use of sheet and strip metal has increascd rapidly during the last few years and manufacturers have been called upon for an ever-increasing tonnage, better drawing quality, and better surface. The automobile industry is probably the most insistent in striving for a better product and a desire to reduce costs. Confronted by these demands, the mills have directed their efforts toward the delivery of material. Their personnel has been occupied largely with the problems incident to production, as any increase forced the use of new sources of raw material with their problems. These problems, combined with those met in the daily routine, have demanded immediate attention, with the result that the standardizing of heat treatments, quality, or temper, etc., have been neglected. Considerable work in standardizing has been done by many companies, but no acceptable method has been developed. The following method, therefore, is given with the hope that some method that can be accepted by the manufacturers and users may be developed. The problem of selecting a material with such properties that the losses in processing are a minimum is interesting and difficult. A description of the properties required is likewise difficult, largely because of loose terms. Another handicap is the number of methods of testing which have not been standardized and concerning which little information is available. In the selection of drawing or forming stock, it is advisable to eliminate as many variables as possible; consequently the method of testing the material is of the utmost importance. The method should be rapid and comparatively easy of application, as it is more important that a large percentage of the stock be tested with reasonable accuracy than that

Jan 1, 1923

By L. N. Brown

The use of sheet and strip metal has increascd rapidly during the last few years and manufacturers have been called upon for an ever-increasing tonnage, better drawing quality, and better surface. The automobile industry is probably the most insistent in striving for a better product and a desire to reduce costs. Confronted by these demands, the mills have directed their efforts toward the delivery of material. Their personnel has been occupied largely with the problems incident to production, as any increase forced the use of new sources of raw material with their problems. These problems, combined with those met in the daily routine, have demanded immediate attention, with the result that the standardizing of heat treatments, quality, or temper, etc., have been neglected. Considerable work in standardizing has been done by many companies, but no acceptable method has been developed. The following method, therefore, is given with the hope that some method that can be accepted by the manufacturers and users may be developed. The problem of selecting a material with such properties that the losses in processing are a minimum is interesting and difficult. A description of the properties required is likewise difficult, largely because of loose terms. Another handicap is the number of methods of testing which have not been standardized and concerning which little information is available. In the selection of drawing or forming stock, it is advisable to eliminate as many variables as possible; consequently the method of testing the material is of the utmost importance. The method should be rapid and comparatively easy of application, as it is more important that a large percentage of the stock be tested with reasonable accuracy than that

Jan 1, 1923

By H. I. Aaronson, H. A. Domian

ELectvon-probe analgsis has been used to in7:estigatr the partition ot alloying- elements between aus-tenite and proeutectoid ferrite (or the Jerritic component of bainite) in high-purity Fe-C-X alloys, lsuully at tzco levels of carbon content fca 0.1 and 0.4 pct in ntost steels) at temperatures between the M, and the Ae3 in Si, mn, Ni, mo, Co, Al, Cr, Cu, and PI steels. No partition ous found during the early stages of transformation at any temperature studied in the Si, ,mo. Co, Al, Cr, and Cu steels. Partition did take place, Jrowel'er, in Ihe Mn, ATi, and Pt steels, occurring in lewtperature. regions below the Ae3 of ca 130°, 65", UNDERSTANDING the mechanisms through which alloying elements influence the kinetics of austenite decomposition reactions which proceed by nucleation and 35c respectively. A break was discovered in the TTT curve for the initiation oj the proeutectoid ferrite reaction in the latter steels at the temperature at which partition began. The alloy content in ferrite at the a:y bondavy remained at constart lecels, shown experimentally to be significantly above those corresponding to eqiilib+iu??l, e'en at the longest reaction times investigated (ca 1o6sec). The partition and the TTT curve observations foere rationalized on the basis of the thermodynamic treatment developed in an accompany ing paper. and diffusional growth has been a major research objective of physical metallurgy since the latter part of the 19th century. The measurements made on the dif-fusivities of carbon and of substitutional alloying elements in austenite during the 1930's and 1940's seemed to provide a useful clue as to the nature of these mechanisms. These measurements showed that the diffu-sivity of carbon is several orders of magnitude higher than that of the alloying elements at a given tempera-

Jan 1, 1967

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Sept. 10 to Oct. 10, 1914: James D. Mooney, Akron, Ohio. J. Kojima, Ashio Copper Mine, Japan. Bernard A. Wilkinson, Guadalajara, H. Starkweather, Cripple Creek, Colo. Mexico. S. S. Langley, New York, N. Y. A. B. Parsons, Candor, N. C.. J. H. Warder, Chicago, Ill. Arthur Feust, Santo Domingo, Nicaragua. Lloyd T. Buell, Butte, Mont. G. B. Marshall, New York, N. Y. George R. Rogers, Gowganda, Canada. Henry Krumb, Salt Lake City, Utah. H. 0. Hammond, Douglas, Ariz. Herbert S. Kohlberg, El Paso, Texas. Percy E. Hohne, El Oro, Mexico. Wilbur L. Cross, Jr., Glen Carbon, Pa. Percy E. Barbour, Candor, N. C. Thomas H. Leggett, formerly-in charge of the mining interests of the American Smelting & Refining Co., has resumed practice as consulting engineer with offices in the Singer Building, New York, N. Y.

Jan 11, 1914

By Yoon T. Auck, Milton E. Wadsworth

Column leach studies of two low grade prophyry copper ores were made with variables of size, flow rate, pH, drainage rate and tempature. Evidence is presented to show that, in some types of ores, sulfide minerals block leaching channels and regulate the rate of dissolution of gangue constituents. Basic iron sulfates, dissolved by introducing acid, provide oxidizing agent in the form of ferric ion in the absence of oxygen. Ferric ion then acts to release copper from the ore. Oxygen up-take was found to increase with the lowering of the pH and to follow parabolic kinetics attributable to the precipitation of basic iron salts within the pore channels. Slow drainage of residual gravitational water can seriously retard oxygen up-take during oxidation for particles in the coarse sand range. A model is presented for dump leaching in which a reaction zone connected by channels to the surface of the ore particle moves topo-chemically during the course of the reaction.

Jan 1, 1973

By William Kelly, F. H. Armstrong

The object of this paper is to describe the electric equipment at the iron-ore mines of Penn Iron Mining Co., Vulcan, Mich. and of Republic Iron Co., Republic, Mich.; to give the results of tests; and to discuss the methods in use from an operating as well as from an efficiency standpoint. Electricity was introduced at the Penn mines for pumping, hoisting, and compressing air in the spring of 1907, upon the completion of a hydro-electric plant built by that company on the Menominee river about 4 miles from the mines. This plant was described in a paper1 presented before the Lake Superior Mining Institute. A paper2 presented at a meeting of the same Institute describes some of the operating features, and the safety devices of the electric hoist at the Curry shaft were briefly described in the Proceedings of the First Co-operative Safety Congress held under the auspices of the Association of Iron and Steel Electrical Engineers at Milwaukee, Wis., Sept. 30 to Oct. 5, 1912. Generating PoweR Plants After the success of electrical operation was assured, a second set of water wheels and generator was installed at the falls, for which provision had been made in the original design and in the construction of the foundations, and later three additional wires were added to the main transmission line, doubling its capacity and reducing the line loss. The general conditions of this installation are particularly favorable for hydro-electric operation. In the neighborhood of three-fourths of the power used is for mine pumping, which in the main is regular and continuous. For air compressing, power is used for about 18 hr. a day for five days, and 9 hr. for one day in the week, though occasionally when shaft sinking is going on a very small amount of compressed air may be

Jan 1, 1915

By Ashok K. Sinha

The quasi-binary systems "VFe3"—VCo,—VNi,— "VCu3"and "TiFe3"—TiCo3,—TiNi3-"TiCu3"have been studied by a combination of microscopic and X-ray methods. Of the Phases encountered, eleven had close-packed ordered layer structures. Within each system, there is an approximately linear variation of the degree of hexagonality of the stacking arrangement with electron concentration, e/a. A study of eighty -four known examples of AB3 structures in transition metal alloys indicates that at e/a = 8.65 the ordered structure of the close -packed layers changes from "triangular" (AuCu3 type) to "rectangular" (SbCu3 type). At e/a < 8.65, the slope of hexagonality us e/a line increases with the group number of the A component. An interesting series of close-packed ordered structures is known to exist at the composition AB3; however, their alloy chemistry has not yet been fully understood. Dwight and Beck1 observed a correlation between position of the components in the periodic table and the type of crystal structure of the binary AB2 structures formed by transition metals. No consistent effect due to atomic size was noted and they proposed that electron concentration* predominates in In the present paper, the AB3 structures are characterized by a symbol describing the stacking and a symbol specifying the ordered layer. The stacking symbol used was introduced by Zhdanov,7 and later used in the International Tables,8 and by Beck9 in his survey of possible layer stacking structures. Alternating positive and negative integers are used to represent the number of positive (e.g., in abcabc...) and negative (e.g., in cbacba...) stacking sequences. T denotes the triangular ordering found in close-packed planes of the AuCu3 structure and R the rectangular ordering found in close-packed planes of the SbCu3 structure, Figs. 3(a) and (b). The present structure symbols are listed in Table I alongside the prototypes, where known, and other structural characteristics of AB3 phases found in the present investigation. EXPERIMENTAL The starting materials were metals of 99.9+ purity. The alloys were prepared by arc melting under argon atmosphere using a nonconsumable tungsten electrode and water-cooled copper hearth. The total weight loss upon melting and subsequent annealing was always less than 0.5 pct and hence the alloys will be referred to by their intended (unanalyzed) compositions. The alloys were homogenized and annealed at suitable temperatures in the range 750" to 1200°C, the annealing periods varying from 3 days at 1200°C to 10 days at 750°C. The heat treatments were carried out in sealed silica capsules under argon atmosphere and with a molybdenum foil cover between the alloy and the walls of the capsule. The quenched alloys were microscopically examined and reduced to powder by crushing or filing. The powders were, whenever necessary, given a stress-relieving anneal at the original annealing temperature. X-ray powder patterns were obtained with an asymmetrical focusing camera, a Guinier-deWolff focusing camera, or a Debye-Scherrer camera. Cr, Co, or Cu radiations were used. In some cases, to ensure the minimum degree of contamination, the deeply etched specimens were mounted in the asymmetrical focusing camera to obtain an X-ray pattern. Internal silicon standards were employed for lattice parameter determinations. The intensity calculations were made by using a Fortran IV program

Jan 1, 1970

September 1 to 6, 1918 COMMITTEE IN CHARGE Spencer Penrose, Chairman. George M. Taylor, Vice-Chairman. A. E. Carlton, Chairman. Finance Committee J. Dawson Hawkins, Secretary DENVER COLORADO SPRINGS CRIPPLE CREEK Finance Finance Thomas B. Crowe T. B. Stearns A. E. Canton , E. P. Arthur, Jr. Richard A. Parker Spencer Penrose N. S. Greensfelder T. B. Burbridge George M. Taylor A. E. Carlton. A. L. Blomfield, Treasurer B. F. Hill Arrangement I F. G. Willis Dave G. Miller Registration Norris E. Eads Frank Bulkley Loren C. Lennox 1V. E. Ryan Geo. E. Collins Horace F. Lunt Fred Jones .1. M. Tippett F. D. Smale Entertainment J. H. Haynes F. H. Bostwick Arrangement and Entertainment L. W. Lennox F. E. Shepard George M. Taylor A. L. Blomfield M. R.. Valentine Howland Bancroft J. D. Hawkins Thomas B. Crowe B. P. Morse A. E. Carlton E. P. Arthur J. G. Perry G. H. Clevenger Etienne A. Ritter Ladies Ladies , PUEBLO Mrs. T. B. Stearns, Mrs. C. M. Taylor, Mrs. C. H. Clevenger J. F. Welborn Chairman. Chairman H. B. Carpenter Mrs. C. Loughridge Mrs. S.-Penrose Mrs. A. E. Carlton L. B. Eames Mrs. H. Bancroft Mrs. J. D. Hawkins Mrs. A. L. Blomfield F. Robinson Mrs. G. Bancroft Mrs. L. C. Lennox Mrs. J. M. Tippett . Mrs. W. D. Leonard Mrs. H. F. Lunt -Mrs. E. C. van Diest Mrs. C. Chase Mrs. E. A. Ritter Mrs. AV. Strieby Mrs. F. H. Bostwick Mrs. L. S. Harner Mrs. C. L. Bailey Mrs. F. Bulkley Miss F. Dickerman Mrs. E. P. Shove Mrs. C. L. Tutt Mrs. F. C. Peck Mrs. F. D. Pastorius

Jan 10, 1918

By E. A. Farrell

A comprehensive survey is made of the status of the asbestos industry as it relates to marketing the product. Included are descriptions of the various types of asbestos and the grading and classification systems used. The uses of asbestos, distribution practices, and types of ore bodies are all related to marketing. World production, the producers and their capacities and world consumption for 1966-67 are summarized and statistical data are included. Asbestos is a general term describing a family of fibrous minerals of the serpentine and amphibole mineral groups. Asbestos has a long history going back to the time of the Egyptians, when it was used as a lamp wick. The commercial mining of asbestos started in Canada, Russia, and Africa in the 1800&apos;s, and the first asbestos products were made in Italy and Russia. The five main types of asbestos are: chrysotile, accounting for 95% of the total mined, amosite, crocido-lite, anthophyllite, and tremolite. Canada, Russia, and Africa are the major producers of asbestos. The commercial utility of asbestos was at first based on the heat resistance of the fibrous mineral in the form of packing, at the start of the industrial revolution. Its current utility is based more on its ability to reinforce binders such as portland cement, rubber, and plastics. Its inertness to the chemical nature of most binders is unique. Most important is its ability to maintain its reinforcing utility when the product is exposed to weather and soil conditions as in asbestos cement boards and pipe, and heat, pressure, and chemical exposure as in brake linings and gaskets and packings. The mineral asbestos is also unique because its fibrous form permits it to be spun and woven to cloth or formed into paper. Many asbestos applications are critical to national defense and at the present time, there are no satisfactory substitutes. Grading and Classification Canadian chrysotile asbestos fiber is graded and priced by length since basically the longer the fiber the higher the utility. The Canadian asbestos industry does not, however, classify the fiber by direct length measurement, but by a dry screening test. The method is called the Quebec Standard Screen (QS) test. One pound of fiber is mechanically shaken in four vertically stacked sieve boxes. The relative proportions remaining on the sieves defines the grade. The longer the fiber, the larger is the amount that stays on the top coarse screens and the less on the lower, finer mesh screens. Other tests can be used to further define the length distribution of fiber such as the wet screen Bauer McNett and the Suter Webb Comb (3 group only). The Canadian grading system divides the milled fibers into 5 main groups: group 3, 4, 5, 6, and 7, with 3 group being the longest, and 7 the shortest. Each group is further divided to subgrades, identified in each group by the letters A to Z, with "A" the longest and "Z" the shortest. See Appendix 1 for the Canadian QS classification system. The Russians also use the QS test on chrysotile. The Africans classify their chrysotile into grades similar to Canadian. The African crocidolite and amosite, however, are classified into actual length groups such as l to 2 in. and 2 to 3 in. Amosite and crocidolite are generally longer than chrysotile but also more brittle. Milled asbestos is not composed of staple length fibers like fiber glass or cotton, but of a mixture or blend of fibers ranging from long to short. Milled asbestos has a fiber length distribution similar to the particle size distribution of a powder. For example, the longest group 3 chrysotile grades have a high percentage of the longest fibers (1/2 to 3/4 in.) and low percentage of short fibers (0.003 in.). The figures in Table 1 give the approximate length distribution of the longest, middle, and shortest groups. A second and further method of classifying fiber is the degree to which the fiber bundles are separated to form a larger number of smaller diameter bundles. This property is normally described as the degree of fiberization, openness or surface area. Air permeability tests are used to measure surface area. Asbestos pro-

Jan 1, 1971

Some 15 years ago, Dr. Adolf Schmidt, director of the Magnetic Observatory in Potsdam, Germany, developed an instrument, which was a modification of Lloyds balance, for the measurement of the vertical component of the earth&apos;s magnetism in the field. There was a keen demand for this because (1) it was desirable to have a field instrument that would measure the component of the earth&apos;s magnetism which stands in the closest and simplest relation to the configuration of the subterranean magnetic formations-the vertical component; (2) it was desirable to have an instrument that was not only more sensitive but also more reliable than the existing vertical magnetometers (the dip needle, for instance). The application of the magnetometer in oil geology demanded such an instrument, because the magnetic disturbances produced by most types of magnetic formations associated with the occurrence of oil (salt domes, faults, anticlines with crystalline core, etc.) are too small to be detected with the ordinary dip needle. The writer can prove, by some investigations recently made for the U. S. Bureau of Mines, that these instruments may be used also to very great advantage in mining, because they are capable of measuring anomalies which are as great as twice the normal strength of the earth&apos;s magnetic field. Even for such anomalies, the field balance is more advantageous than the dip needle. First, the instrument rests on a firm support and can be adjusted in the proper azimuth, which insures measurement of the vertical intensity only, without a part of the horizontal intensity, which is very important for the interpretation. The readings give the vertical intensity in linear terms and not as a function of an angle; and the field balance is insensitive to temperature when used with scale values that are adequate for the determination of large anomalies. In another phase of mining, the gold placer work, the field balance has also shown excellent results for which the dip needle is not adequate. What has been said about the dip needle holds also, though to a lesser extent, for two other types of vertical variometers recently used, the Tiberg balance and the Thomson-Thalen magnetometer.

Jan 1, 1929

By William Phillips

THE earliest mention of the sulphur deposits in what is now Culberson County, Texas, seems to be contained in "Explorations and Surveys for a Railroad Route from the Mississippi River to the Pacific Ocean, United States War Department, 1853-54." Captain John Pope (he was not commissioned Captain until 1856) had charge of one of the divisions of the Survey. In his report on the geology of the route, William P. Blake noted the analysis of a greenish earthy powder from the bed of Delaware Creek, at the springs, which contained 18.28 per cent. of free sulphur. The report states: "From the chemical examination of the waters of the spring, by Dr. Booth, it appears that chloride of sodium is the principal solid ingredient, but considerable quantities of sulphide of sodium are present. * * * * * The waters from the springs examined by Dr. Booth were alkaline, but it is possible that some of the springs are acid; and in this case the precipitation of sulphur would ensue on the mixture of the acid waters with those charged with alkaline sulphurets and the origin of the deposits of sulphur would he thus explained." This is the first reference to the existence of sulphur in that region, the first mention of the character of the water found there and the first suggestion as to the&apos; origin of the deposits. The possibility of the existence of acid waters was confirmed by E. M. Skeats, nearly 50 years later.1 In this publication, Skeats says that the water from the sulphur deposits in Section 11, Block 114,, Township 5, contains 79.08 grains of free sulphuric acid per gallon. This locality is about 13 miles (21 km.) south of Delaware Creek and about 35-miles (56 km.) east of the Delaware Springs. The next published reference to the existence of sulphur in Trans-Pecos Texas is in the First. Annual Report of the Geological Survey of Texas, 1889, page 226, where W. H. von Streeruwitz mentions that sulphur is found in that region, but gives no further information. In the

Jan 9, 1917

By Fun-Den, Wang

An open pit rock structure usually contains geological planes of weakness. They are formed by joints, faults, bedding planes, fractures, and cleavages. Rock slope failures often occur in the form of sliding of rock blocks along a plane or several planes. Such a rock block has three- dimensional geometry, and consequently a vector method of analysis has been found useful in evaluating its stability. Rock blocks of a tetrahedral shape with one free surface have been analyzed by Londe. Rock blocks formed by sets of parallel joints have been analyzed by Wittke. The present chapter presents the analysis of rock blocks formed by planes of weakness of arbitrary orientation, and of three-dimensional geometry.

Jan 1, 1972

By D. E. Hawk, R. F. Burdyn, F. D. Patchen

Earlier work on a mud separator for barite recovery is extended to the design and construct ion of a rugged field unit. Problems associated with scale-up for field use include the me of dilution water and its effect on capacity, power requirements and pressures developed. Equations for these quantities are derived and applied in maximizing the beneficial effects of dilution and minimizing the power required. Tests on the full-size rotor show that its performance can be predicted by theory. The completed unit is compact and lighter than current decanting types. Its capacity is from 10 to 22 gal/min with corresponding barite recovery efficiencies of 92 to 86 per cent. INTRODUC&apos;TION In an earlier publication a new type of centrifugal device was described for solid-liquid separations.l In that paper an operating equation was derived, and its validity demonstrated in laboratory scale experimentation. Some of the features apparent in this new device seem particularly well suited to the conservation of barite in field drilling-mud systems, hence the development was extended to the design and construction of a field unit. In the present paper the design problems associated with scale-up are considered. A full-scale, rugged self-contained field unit is described, and test results discussed which verify that the performance of the large field unit can be described by a simple operating equation. PRINCIPLE OF OPERATION OF SEPARATOR In principle, the new device is simply a perforated cylinder rotating within a body of fluid which is contained within a stationary case, as in Fig. 1. The frictional drag generated by the rotating cylinder causes part of the fluid to rotate. At the surface of the cylinder, assuming no slip occurs, the angular velocity of fluid and of the cylinder are identical. If there are suspended particles present of greater density than the fluid, the centrifugal force acting on these particles causes them to move radially away from the cylinder at some velocity vp . Where the Stokes settling equation holds, this velocity may be expressed as:2 d2 ?p rw2 If the case is provided with openings at both ends, a suspension can be pumped in at one end at a fixed rate. Part of the suspension can then be removed at a fixed rate at the other end of the case as underflow, and the remainder forced through the perforations and hollow shaft of the rotor to appear as effluent, also at a fixed rate. The radial component of the flow velocity of this stream as it reaches the rotor surface, is simply effluent flow rate divided by cylindrical surface area: Because up is a function of particle size, for some particular particle size, the velocities vp and v, will be equal in magnitude. This is defined as the critical particle size and represents the size above which all particles appear in the underflow and below which all particles appear in the effluent. For this equilibrium condition at the rotor surface, Eqs. 1 and 2 combined give

Jan 1, 1966

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930