Search Documents

By P. B. Mee

The secondary re crystallization behavior of two vacuum-melted, nominally 3 pct Si-Fe alloys has been studied, one alloy being produced from pure electrolytic iron and semiconductor-grade silicon and the other from commercial-purity hot band. The vacuum-melted and vacuum-remelted alloys were found to develop {110}(hhl) and {lll)(hkl), respectively, on annealing in high vacuum and {100}(0kl) and {11l}(hkl), respectively on annealing in pure hydrogen of dew point, < — 60°C. H2S doping of the hydrogen or annealing in commercial argon was found to effect a reversal for the vacuum-remelted alloy from (111) to (100) secondary recrys-tallization, while prolonged vacuum annealing at 2 x 10-6 Tow resulted in a tertiary re crystallization from (111} to (110). The growth selection of the {lll}(hkl) component was found to be governed predominantly by the {111}/planar misorientation, the maximum deviation of the resulting secondaries being 5 deg. It is considered that the driving force for {111}(hkl) secondary recrystallization arises from the preferential lowering of ?111, possibly by phosphorus or nitrogen diffusion, just as oxygen and sulfur under certain conditions have been found to preferentially lower ?100. When heavily cold-rolled metals are annealed at high temperatures, primary recrystallization usually occurs rapidly and may be followed by considerable grain growth. However, in the presence of a fine dispersion of inclusions1"3 or with a strong matrix preferred orientation4&apos;&apos; the matrix may be stabilized and a secondary recrystallization may then be effected. Also, in vacuum-melted Si-Fe it has been shown possible to develop {100}(001) and {110}(001)6 surface energy driven secondary recrystallization textures. Further, it has been found that, on annealing very pure metals, grain growth normally ceases when a grain size approximately twice the strip thickness is acquired, due to the formation of V-shaped thermal grooves which result in an equilibrium being set up between surface and grain boundary stresses. If, however, a surface energy difference ??s, exists between adjacent grains (of the order of a few percent of the grain boundary energy ?b), then according to Mullins8 a secondary recrystallization may be effected, since the grains having lowest ?s would grow at the expense of their higher-energy neighbors. For clean bee metal surfaces ?110 should be lowest; however, for 3 pct Fe-Si (100) secondary structures have frequently been developed and have been attributed by Walter and Dunn9 to an alteration of the relative surface energies due to the preferential chemisorption of oxygen on (100) planes. Kohler,10 however, indicated that this reversal may be achieved by employing minute quantities of highly polar compounds in the annealing atmosphere, i.e., sulfur compounds, in par- ticular H2S being beneficial in (100) growth. This work has been verified by Kramer" using {100)/{110} bicrystals, while Mager12 demonstrated the importance of sulfur diffusion within the strip. Detert13 has intimated that carbon may be responsible for the preferential lowering of ?110 although no direct evidence has appeared yet to support this supposition. It must , be appreciated that the above-mentioned examples of surface energy driven secondary recrystallization were obtained with very pure vacuum-melted materials with oxygen contents (which is now known to be a critical factor") less than 35 ppm. During the course of a textural study on Si-Fe it has been found that under certain conditions (111) secondary recrystallization can be obtained by what is believed to be a surface energy growth selection mechanism. The purpose of the present paper is to briefly describe this result and to try and postulate the possible causes. EXPERIMENTAL Two vacuum-induction-melted, nominally 3 pct Si-Fe alloys were produced, one from pure electrolytic iron and semiconductor-grade silicon designated A and the other from commercial-purity hot band, designated B.

Jan 1, 1969

By C. K. Leith

THE outstanding fact of the mineral world today, at home and abroad, is the surplus of current production, and particularly of capacity for production, over current requirements. This is not by Any means a new condition, but never before has it loomed up in such&apos; menacing form. - Those of us who have devoted most of our professional efforts to the discovery and development of &apos;new mineral supplies now suddenly find ourselves with the job apparently accomplished, waiting for some one else to find an outlet for excess mineral production before we can further. The management of the industry is in much the same boat. The psjrcho16gy of the industry has been so grooved in the direction of acquisition of, minerals that at the present moment the mineral industry confronts the new problem of surplus in more or less of a daze.

Jan 1, 1931

By C. G. Dunn

This note describes a method for revealing micro-structures in tantalum through an {hkl} effect which was found during a study involving amorphous and crystalline tantalum oxides. Three steps are involved. First, an amorphous film of Ta2O5 is formed anodically1 on the surfaces of the tantalum. The amount needed depents on the thickness of the substrate tantalum; 1600Å of oxide, however, is generally satisfactory in the 1/2 -mil (12 µ) to 3-mil thickness range. The film at this point is uniform in color. Second, the anodized specimen is heated to 800°C in. vacuo during a period of a few minutes and held at temperature for 5 min. During such a treatment some oxygen leaves the oxide through dissolution into the substrate tantalum (e.g., at 10-8 Torr oxide films thinner than about 800 completely disappear on 5-mil strip). Considerable crystallization of the amorphous oxide also occurs adjacent to the metal/oxide interface but not throughout the oxide thickness. The thickness of oxide needed as a residue is not too critical; values between 500 and 1000Å (optical estimate&apos;) may be most useful. (The presence of a residual oxide layer after the heat treatment usually is not apparent; in fact, in most instances the surfaces have a metallic appearance. This can be the case also for thicker residual films needed in the detection of a crystalline oxide phase by surface X-ray diffraction—e.g., if the initial oxide film is 3000Å thick, enough crystalline oxide is formed for X-ray detection.) The third step eliminates the metallic appearance at the surface and reveals (or produces) a varied colored film of tantalum oxide. Two methods can be used and both will be illustrated. If the specimen is dipped in 48 pct HF for a few seconds, the tantalum is found to be covered with a multicolored oxide. Moreover the colors correlate with the grain structure of the substrate tantalum through an orientation dependence of the type illustrated in Fig. 1, where results of an orientation analysis by the Laue X-ray method have been plotted. Other film conditions would have provided a different set of colors for the same orientations. Any such correlation, however, provides a basis for a qualitative assessment of the distribution of orientations in a large sample. The cold-rolled structure of tantalum foil produced by a recrystallization anneal and a cold-rolling reduction of 95 pct is not easily obtained by usual metal-lographic methods.&apos; The structure, however, is easily revealed by the present technique, Fig. 2. The alternative third step is to reanodize the specimen. The optical nature of the final anodic film depends on the presence of the crystalline oxide phase; color variations indicate optical thickness variations in the film. As the reanodization voltage is increased from zero, straw and light brown colors appear (as usual), followed now by variations in color from grain to grain depending on {hkl} orientation. Suitable end points, which are determined by voltage and time, are easily established. Fig. 3, for example, shows the grain structure developed in 5-mil tantalum strip during a 30-min re-crystallization and grap-growth anneal at 1800°C. An anodic film of 1600Å thickness was added prior to the special 800°C anneal. Reanodization was done at constant current density (near 0.2 ma per sq cm) in an aqueous solution of H3PO4 (0.01 pct) and was terminated after the initial brown colors were replaced by a deep blue at approximately 30 v. Although good grain contrast can be obtained with bright field illumination, even greater contrast for black and white micrographs may be obtained with polarized light, as in Fig. 3.

Jan 1, 1967

Jan 3, 1953

By Zay Jeffries

A SURVEY of rare metals and minerals for the past year places uranium as one of two partners, the other being the neutron, in what historians will probably say is the greatest discovery in physics at least during the year and probably for a consider- ably longer period. The uranium atom has been made to divide into parts somewhat after the style of reproduction of the amoeba. When an amoeba divides into two parts, however, it produces two amoebae substantially alike and each substantially like the parent: furthermore, there is no considerable change of energy when this happens. When the uranium atom divides it yields other atoms such as barium and krypton with the complete destruction of the original uranium atom but with the liberation of a tremendous amount of energy. This will be discussed more at length later.

Jan 1, 1940

By W. J. Parton

THE efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/3 2 by 1/3 2 in.) and No. 5 Buckwheat (1/3 2 in. by 0), present a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than s, 32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes.

Jan 1, 1949

By Joseph A. Holmes

The public is already familiar with the general fact that the scope and the financial resources of the approaching St. Louis World&apos;s Fair are much larger than those of any of the preceding great expositions; and both the visitor and the exhibitor, when he comes to St. Louis in 1904, will find it to be a real World&apos;s Pair, with exhibits and visitors from every known country. Passing over the subject, as to the general Exposition, with this brief statement, I ask Sour attention to the consideration of a few important facts connected with the proposed mining exhibits at this Exposition. First of all, I may say that. reading- and writing-rooms and library facilities will be furnished in the Mines Building for miners and mining engineers, and it is expected that when they visit the Exposition they will make these rooms their headquarters, and give the Chief of the Department and his assistants an opportunity to extend to them such courtesies as may be possible. One of the exhibits in the Mines Department will consist of models and maps arranged to show the nature and extent of the mining operations in the United States at the time of the purchase of the Louisiana Territory in 1803, the event which

Jan 1, 1903

By M. B. Hopkins

FOR years the expression "except rubber, tin, and manganese" has appeared in practically every discussion of the natural resources of the United States. Knowledge that natural rubber is not produced in the United States has now spread from the relatively few who have reason to be interested in the country&apos;s basic raw material supplies to all those who ride in automobiles, which means everybody. This "everybody" reads in the daily papers that we have a stock pile of natural rubber and that plenty of synthetic rubber is just around the corner. Statistics as to the United States&apos; rubber requirements and sources of supply are of interest to him only to arrive at an answer to the question : "After taking care of rubber requirements for military purposes, will there be rubber for my automobile and the many other rubber articles I want?" More than 30,000 different rubber articles are manufactured in addition to the tires and tubes which use up about 70 per cent of the rubber supply.

Jan 1, 1942

By H. J. R. Way

THE work to be described was undertaken at various periods from 1937 to 1939 on the Busia gold field, in the eastern province of Uganda. It was decided to examine the possibility of reef prospection by the resistivity method, for it was not known how far the usually disintegrated nature of most reefs in the ubiquitous laterite near the surface would obscure indications obtained by resistivity traverses. The work at the commencement was therefore largely experimental, but the results obtained thereby were satisfactory, and a survey was started at the Government closed area at Amonikakine. With the limited time and resources at the writer&apos;s disposal, it was not possible to complete the survey to his satisfaction or to follow up exhaustively all the geophysical indications, but some of the results of the experimental work and the survey were of sufficient interest to be worth recording; in particular the relation between the width of reef, electrode separation and shape of the curve, and the interference effect of constant separation curves over zones of float are significant and useful. Three new veins were located, but only one contained sufficient gold to warrant detailed prospection. This was called the Geophysical reef, and was uncovered over a strike distance of 1140 ft., and there are indications that it extends over a distance of 1990 ft. These results and the recommendations consequent therefrom were embodied in a special report to the Uganda Geological Survey. HISTORY OF THE FIELD The Busia field is in the southeastern corner of Uganda near the Kenya-Uganda border, and is about 17 miles north of the northeastern corner of Lake Victoria. Gold was first discovered in the area in the stream beds by Davies1,2 in 1932. Subsequently numerous small alluvial claims were worked by prospectors and the area was prospected for reef by a company for periods varying from three to nine months, but was finally abandoned, as the results were considered unfavorable. Further prospecting by the Geological Survey in 1935-1936 under Davies3 and later under the writer4 uncovered three reefs with sufficient gold values to be of economic interest. These were finally taken over by a company known as Borderland Syndicate, which still owns the area, and from September 1937 to the end of 1941 about 13,000 oz. of gold was extracted from reefs of the area proved by the Geological Survey. Opencast mining operations are still proceeding (February 1943). The Amonikakine area lies to the immediate north of that of Borderland Syndicate. A certain amount of prospecting had been done when the writer started work there. As a result of his report, this area was taken over by another syndicate, but little further work was accomplished before it ceased operating because of difficulties of wartime working.

Jan 1, 1944

By J. R. Lewis, J. H. Hamilton, V. D. Hanson, K. W. Heinlein, J. M.194-000-000-006 Vonfeld, J. P. Denny

TWO overfeed drum-type separators using a suspension of magnetite in water as the separating medium have been installed in the Champion NO. 1 preparation plant of the Pittsburgh Coal Co., Division of the Pittsburgh Consolidation Coal Company. A simplified flow diagram of the Champion No. 1 coarse coal circuit is shown in Fig. 1. A railroad car rotary dump, capable of handling 20 cars per hr, discharges the coal into a hopper. Coal is fed from the hopper of the rotary dump to a 60-in. belt conveyor by two reciprocating pan-type feeders. The belt conveyor feeds the run of mine coal onto the main raw coal screen. The first deck is fitted with 3 in. round hole perforated plate which removes the 3x0-in. coal. The second deck of the screen is equipped with 6-in. lip screens which separate the remaining coal into +6 in. and 6x3 in. The +6 in. coal is transferred to a shaking picking table and then discharged onto the loading boom. The 6x3-in. coal is fed to the No. 2 dense medium vessel for cleaning. The clean coal from this unit flows to a vibrating screen where the medium is removed and the coal sized into 6x4 in. and 4x3 in. The 6x4-in. coal is transferred to the loading booms and the 4x3-in. is conveyed to the clean coal classifying screens to remove degradation. The 3x0-in. raw coal is blended in a system composed of three storage bins having a total capacity of 400 tons. From these bins the coal is fed onto a 48-in. flight conveyor by three reciprocating feeders. This flight conveyor delivers the coal to the Rheo plant. The 3x0-in. coal is then cleaned in two 48-in. Rheolaveur launders each equipped with two Rheo boxes. The first set of boxes removes a primary refuse and the second set produces a middling product which is recirculated in the launders. The cleaned coal and water overflows from the primary launders to two sizing and dewatering shaker screens where the water and — -in. coal are removed for further cleaning in the Rheo fine coal plant. The 3x3h-in. clean coal is combined with the 4x3-in. coal from the No. 2 vessel, sized into 4x2 in., 2x1 34 in., and 1&apos;/4x in., then sent to the loading booms. The 3x0-in. refuse from the primary launders is normally fed to the No. 1 dense medium circuit, but any portion or all of this material can, as an alternate, be processed in the Rheo rewash launder. The primary refuse when fed to the dense medium circuit is screened into YSXO which is cleaned in the fine coal plant and 3x for cleaning in the No. 1 vessel. The clean coal from this vessel is passed over a vibrating drainage and rinse screen, then sluiced to the rewash sizing shaker where it is dewatered and sized for loading. The installation of a pilot plant separating vessel using a suspension of magnetite in water was pro-

Jan 1, 1953

By J. H. Hamilton, J. R. Lewis, K. W. Heinlein, V. D. Hanson, J. M. 194-000-000-006 Vonfeld, J. P. Denny

TWO overfeed drum-type separators using a suspension of magnetite in water as the separating medium have been installed in the Champion NO. 1 preparation plant of the Pittsburgh Coal Co., Division of the Pittsburgh Consolidation Coal Company. A simplified flow diagram of the Champion No. 1 coarse coal circuit is shown in Fig. 1. A railroad car rotary dump, capable of handling 20 cars per hr, discharges the coal into a hopper. Coal is fed from the hopper of the rotary dump to a 60-in. belt conveyor by two reciprocating pan-type feeders. The belt conveyor feeds the run of mine coal onto the main raw coal screen. The first deck is fitted with 3 in. round hole perforated plate which removes the 3x0-in. coal. The second deck of the screen is equipped with 6-in. lip screens which separate the remaining coal into +6 in. and 6x3 in. The +6 in. coal is transferred to a shaking picking table and then discharged onto the loading boom. The 6x3-in. coal is fed to the No. 2 dense medium vessel for cleaning. The clean coal from this unit flows to a vibrating screen where the medium is removed and the coal sized into 6x4 in. and 4x3 in. The 6x4-in. coal is transferred to the loading booms and the 4x3-in. is conveyed to the clean coal classifying screens to remove degradation. The 3x0-in. raw coal is blended in a system composed of three storage bins having a total capacity of 400 tons. From these bins the coal is fed onto a 48-in. flight conveyor by three reciprocating feeders. This flight conveyor delivers the coal to the Rheo plant. The 3x0-in. coal is then cleaned in two 48-in. Rheolaveur launders each equipped with two Rheo boxes. The first set of boxes removes a primary refuse and the second set produces a middling product which is recirculated in the launders. The cleaned coal and water overflows from the primary launders to two sizing and dewatering shaker screens where the water and — -in. coal are removed for further cleaning in the Rheo fine coal plant. The 3x3h-in. clean coal is combined with the 4x3-in. coal from the No. 2 vessel, sized into 4x2 in., 2x1 34 in., and 1&apos;/4x in., then sent to the loading booms. The 3x0-in. refuse from the primary launders is normally fed to the No. 1 dense medium circuit, but any portion or all of this material can, as an alternate, be processed in the Rheo rewash launder. The primary refuse when fed to the dense medium circuit is screened into YSXO which is cleaned in the fine coal plant and 3x for cleaning in the No. 1 vessel. The clean coal from this vessel is passed over a vibrating drainage and rinse screen, then sluiced to the rewash sizing shaker where it is dewatered and sized for loading. The installation of a pilot plant separating vessel using a suspension of magnetite in water was pro-

Jan 1, 1953

The following is an incomplete list of members and guests who called at Institute headquarters during the period July 11, 1918 to August 11, 1918. John Carter Anderson, Tucson, Ariz. Edson S. Pettis, San Francisco, Cal. Lieut. Frank A. Ayer, Tyrone, N. M. Wm. H. Rettie, Yonkers, N. Y. W. R. Canton, McGill, Nev. J. T. Robertson, Port Richmond, S. I. Alden Crankshaw, Palmerton, Pa. Harry O. Robinson, Margarita, John Davenport, W. Norfolk, Va. Venezuela. A. Faison Dickson. C. K. Seng, Gilbert, Minn. F. A. Fahrenwald, Cleveland, C). E. S. Sheffield. L. Hall Goodwin, New York. H. G. Smith. W. H. W. Hamilton, Baker, Ore. Harry M. Spoor. Floyd D. James, St. Louis, Mo. H. H. Stoek, Urbana, Ill. George A. Laird. Arthur L. Tuttle, Copperhill, Tenn. J. W. McBride, Spokane, Wash. Thor Warner, Phoenix, Ariz. Arthur Notman, Bisbee, Ariz. Christopher G. Atwater, Manager Agricultural Dept., The Barrett Co., is in Washington serving the U. S. Navy Bureau of ordnance in connection with the Navy nitrate plant recently authorized by Congress. Edward Ludlam Blossom announces his marriage to Mabel Townsend, daughter of Mr. and Mrs. George Comings Mills, on Wednesday, July 17, 1918, at New York City.

Jan 9, 1918

By Gary B. Williamson, Barton K. Cross

Digital simulation is a modern analysis tool which allows the mine operator to evaluate the result of making a decision without actually changing the organization or buying the equipment. The purpose of this paper is to demonstrate the use of digital simulation in evaluating a decision of whether or not to introduce dispatching in an open pit mine. The analysis shows that appreciable savings can be realized by dispatching. In certain cases, an operator can reduce the number of trucks required to move a specified tonnage. A second analysis evaluates the alternatives of using one large shovel or two smaller units. In this case, the operating cost of the haulage equipment necessary to support the shovels turns out to be the critical factor in this decision.

Jan 1, 1969

By E. A. Peretti

BEFORE embarking on a detailed investigation of the system indium-antimony-bismuth, experiments were carried out to determine the existence of quasi-binary sections. The bordering binary systems are known1 and show the occurrence of three intermetallic binary species corresponding closely to InSb, InBi and In2Bi. Attention was focused on the low-indium end of the ternary diagram where the possible quasi-binary sections, excluding ternary compound formation, would involve the pairs: InSb-Bi, InBi-Sb and InSb-InBi. The latter pair revealed itself as a true quasi-binary, so it was investigated fully by thermal analysis, x-ray and microscopic examinations. All compositions were made by proper combination of three elements involved. The indium had a guaranteed purity of 99.97 pet; the antimony contained 99.99 pet Sb, and the bismuth had a purity of 99.99 pet. Alloys were made by melting together antimony, bismuth and indium in evacuated, sealed pyrex-glass tubes at a temperature of 600°C with vigorous agitation. The melts, weighing about 80 grams, were allowed to freeze in the sealed tubes and finally were transferred to glass tubes for the taking of cooling and heating curves. A protective atmosphere of helium was used, and the melts were stirred mechanically while cooling at rates of from 0.5 to 3°C per min. Temperatures were measured with a calibrated chromel-alumel thermocouple and were recorded graphically on a Minneapolis-Honeywell extended-range recorder working in conjunction with a Leeds and Northrup type K-2 potentiometer. Conventional polishing techniques gave satisfactory results in preparing specimens for microscopic examination. Etching was carried out with Vilella&apos;s reagent or aqueous mixtures of chromic oxide with either nitric acid or sulfuric acid plus dichromate. Conclusions deduced from the thermal analysis and microscopic examinations were confirmed by X-ray photograms using Co-K alpha radiation. The phase diagram is shown in Fig. 1. The liqui-dus consists of an uninterrupted line running from the freezing point of InSb (525°C) to a eutectic point experimentally indistinguishable from the freezing point of InBi (110°C). X-ray patterns of the InSb show a slight expansion of the lattice with the addition of InBi, and microscopic work indicated the solid solubility of InBi in InSb to be less than 0.5 pet at room temperature. Acknowledgment We wish to thank the Indium Corporation of America for the loan of the indium used in this investigation. References 1 E. A. Peretti and S. C. Carapella, Jr.: Trans. ASM., 1949, vol. 41, P. 947. T. S. Liu and E. A. Peretti: Trans. ASM, 1952, vol. 44, p. 539. Metals Reference Book, vol. 1, 2nd ed., AIME, p. 345.

Jan 1, 1959

By Robert L. Slobod

In much of the work reported in the literature on long cores. true connate water value, probably have not been obtained because of insufficient flow of 011 to attain equilibrium. A -.satisfactory method for establishing connate water in long cores has been developed in which oil flow is maintained until no additiona1 water is displaced. INTRODUCTION Long cores have been used by sev-erals investigators in an effort to evaluate the efficiency of oil recovery for various producing schemes. The effects of many variables such as rate of displacement. pressure drop, volume of displacing medium, gas-oil ratio, inter-facial tension, and others have been investigated, and the merits of gas drive have been compared with water drive. In the older experiments no connate water was used. but in the more recent stndies the philosophy of the experiment calls for a core containing oil and connate water (irreducible water) as the starting point of the experiment. The method generally used to establish this condition in long cores involves dynamic&apos; displacement wherein one or more phases are forced through the core. flow being maintained at a constant rate or at a constant pressure until a steady state is reached wherein there is no change of saturation with time. It is one purpose of this paper to point out that in much of the work reported in the literature true connate water values probably have not been obtained. The reason for this failure is pointed out. and a method for obtaining more reliable connate water values on long cores is presented. It is impossible at this time to completely evaluate the effect on the conclusions in the earlier papers resulting from the failure to obtain true connate water in the long cores, but some data are presented which indicate that serious errors may he present in many cases. MATERIALS AND APPARATUS Cores cut front outcrop sandstones (Strawn. Torpedo, and Elgin sandstones) with permeabilities of the order of 300 md were used. The major experiments were made with a core 18-in. long and 2-in. in diameter. Cores of the same diameter but only 12-in. long were used in a few tests? and in some work a core I-in. in diameter and 11-in. long was used. These materials were all somewhat bentonitic. &apos;To reduce the effect of such constituents, one of the cores (Torpedo No. 10) on which the most work was performed was acid extracted at the start of the experiment. Brine containing 50,000 ppm chloride and naphtha (Stoddard&apos;s Solvent) were used as the water and oil phases, respectively. The core was mounted in a rubber sleeve which forms the inner lining of a brass cylinder. In this arrangement2 the rubber sleeve is forced against the core by applying pressure to water in the annular space between the rubber sleeve and the brass cylinder wall. The core is therefore sealed in rubber so that all fluids introduced at the input end of the core flow through the core. With this equipment the core may be easily removed for inspection and analysis. Also, other cores may be introduced for study with no extra time for preparation such as is required when plastic mounting is used. When pressure or conductivity measurements are desired at intermediate points along tile length of the core, the brass cylinder comprising the outer jacket of the core holder is cut into section, of the desired length. Each section is then made up as an individual unit with its own rubber sleeve (see Fig. 1). The individual units are then butted up against a ring of plastic or other insulating material which carries an electrical contact for resistivity measurements and an opening which can be used for the measurements of fluid pressures. The individual units are forced tightly against the plastic ring separators and held in place with several tie rods. Inlet and outlet end butts of the same diameter as the core and several inches in length are provided to control the introduction and withdrawal of fluids and to complete the arrangement for sealing the core within the rubber sleeve. Fluid flow is maintained either by applying pressure to the liquid confined in a reservoir or by the use of a gear pump. The latter is preferable where continuous flow at a moderate rate over a long time interval is desired since a small volume of liquid can be readily recirculated using filters to prevent plugging of the core. EXPERIMENTAL The oven-dried core is weighed and is then completely saturated with brine

Jan 1, 1950

By R. L. Wiegel

The two questions considered in this study are: (1) what similarity is there in the liberation of magnetite from various iron formations, and (2) how is this liberation affected by the size reduction technique employed. Twelve sample suites were obtained from commercial concentrators processing magnetite iron formation in the United States, Canada, and Australia. These samples have grades in the range 15 to 45% magnetite iron and approximate mineral grain sizes o f 50 to 2000 microns. Efforts were directed at measuring the liberation characteristics of the samples obtained from the concentrators primary grinding mills. The Davis tube, a laboratory magnetic separator, was used to concentrate individual size fractions of the size reduction product to determine liberation data. These liberation data were compared with relationships calculated from a highly idealized mathematical model of liberation in a binary mineral system. The results of these comparisons have been encouraging for nine or ten of the twelve samples tested. This leads to the conclusion that for most commercial iron formations, at least with conventional rod mill size reduction, it is possible to quantitatively characterize liberation with two parameters: an effective mineral grain size and ore grade. Limited laboratory size reduction tests as well as one of two sets of liberation data from commercial primary autogenous grinding lend some support to the contention that autogenous grinding can affect mineral liberation.

Jan 1, 1976

[†AARONSON, ALFRED E., Vice-Pres., Mid-Co. Petroleum Co., Mid-Co. Bldg. Tulsa, Okla. &apos;18 ABADIE, EMILE R., Min. Engr Address wanted. &apos;76 ¦ABADILLA, QUIRICO A. Geol. Dept. Cia. Mexicans de Petroleo "El Aguila," S. A., Edifico "El Aguila," Esq., Calles Aurora y Comercio,] [ ]

Jan 1, 1925

By Paul E. Rosten

Introduction This papers describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Co. to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Co. operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously (Lindroos and Koski, 1966; Villar and Dawe, 1975; Koski, 1977). Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and fur¬nished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate¬kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to: (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1981

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By M. E. Straumanis, R. P. Shodhan

LATTICE parameters of molybdenum of various purities are summarized in Table I. The latter shows that the parameter fluctuates between 3.1467 and 3.1475A. The room-temperature expansion coefficient a is also not well-known as values from 4.90 to 5.20 x 10-6 can be found in the literature.=-&apos; It, therefore, seemed appropriate to repeat the measurements under exactly controlled conditions, using high-purity Hilger molybdenum powder (containing 0.0015 wt pct of Fe, 0.005 of Si and traces of other elements) and a 99.95 pct pure Sylvania Electric preparation (containing Cr, Fe, Ni, Si, Sn, and C in amounts of 50 ppm of each and in still smaller amounts Cu, Pb, Mg, and Mn). Of course, both samples could have contained at least 0.01 pct of oxygen in form of a surface oxide. However, oxygen, because of its small solubility in molybdenum, does not influence its lattice constant.g The determinations were made in a cylindrical precision X-ray camera, 64 mm in diam, the temperature of which was controlled within *0.05"C, by inserting it into a special thermostat." To exclude the film shrinkage effect (after the development of the film), the asymmetric film placement method was used." Absorption corrections (e.g., by extrapolation)" were unnecessary because of the use of a thin Li-B-glass fiber (about 0.08 mm in diam) which was fastened to the sample holder of the camera and dusted with the fine molybdenum powder. Cum radiation of the wavelength 1.389350 kX was applied because it produced in 30 min the line (420) having a high Bragg angle of about 81.6 deg. The conversion factor of 1.00202 gave the results in angstroms. To obtain the expansion coefficient a, exposures were made at various temperatures t, see Fig. 1, on at least two films at each temperature. The films were measured with a componator and the lattice constants a were calculated. The expansion coefficient was found from: where a2s is the constant at 25°C and A is the change in a and t. The same equation (knowing a) was used to reduce all the constants obtained at various temperatures to that of 25"C, Table 11. The probable error S507p (at a 50 pct confidence limit) was calculated from the reduced constants:

Jan 1, 1969