Search Documents

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By A. Singh, W. M. Fleming, J. J. Santana, A. E. Torma

The present study investigated the extraction of uranium from a low-grade ore by sulfuric acid and the removal of radium from the leach residues by brine solutions. The optimum leaching conditions were found to be 1.5 mole [£]-1 H2SO4, 6.Og[9]-1NaClO3, 75°C,50% pulp density and 750 rpm with respect to the rate of uranium extraction. The maximum theoretical attainable rate of uranium extraction was determined to be V = 1.09 x 10 -2 mole [¢]-1h-1 with respect to pulp density. The order of reaction was found to be zero regarding the effect of sodium chlorate concentrations. The apparent activation energy of uranium extraction was calculated from the Arrhenius plot to be [A]E a - 2.36 kcal mole-1 (9.87 kJ mole-1). Based on a statistical design, an empirical equation has been developed describing the rate of uranium extraction with the leaching parameters. This equation can be used to generate data which may be useful for scaling up the process to pilot plant level. The most efficient brine solution for the extraction of radium - 226 from the leach residue was found to contain one mole[f] -1 CaCl2 and 0.01 mole [2] -1 HC1. The two step leaching with this solution resulted 87% removal of radium from the leach residue. On the basis of this study, a flow-sheet has been proposed for the extraction of uranium and radionuclides from the ore and leach residue to yield almost innocuous tailings.

Jan 1, 1982

By D. Harker, E. Epremian

The constitution of the nickel-tungsten system has been studied by a number of investigators, the most recent of which are Ellinger and Sykes.1 On the basis of metallography, electrical resistivity and hardness measurements and some X ray diffraction work, they constructed a consitution diagram (Fig 1). Ellinger and Sykes report a0 for the alpha face-centered cubic phase (nickel saturated with tungsten) as 3.66?.‡ The gamma phase (tungsten saturated with nickel) is given as body-centered cubic, but no value of a. is recorded. At 43 pct tungsten by weight (approximately 20 at. pct) a beta phase is reported, but structure and lattice parameter are not known. Primarily on the basis of metallographic evidence, they conclude that beta is a new phase and rule out the possibility of formation of a superlattice since they- observe a new phase in the microstructure. Grube and Schlecht2 report an ordering reaction in a system similar to the Ni-W (Ni-Mo) and Harker3 has shown that NirMo forms a superlattice upon the pre-existing face-centered cubic lattice of the alpha phase. Elliniger arid Sykes observed a change in the diffraction pattern of a 4.3 pct W alloy upon aging and attributed it to the formation of a new phase. Thus, there appears to be some question as to the character of the beta phase reported by Ellinger and Sykes. The purpose of the present work is to determine precisely the structure and nature of the beta phase in the Ni-w system of X ray diffraction methods. Experimental Procedure One inch diameter ingots of 43.66 pct, 40.15 pct and 34.06 pct .tungsten by weight (19.8, 17.6 and 14.1 at. pct respectively) were melted and cast under vacuum from electrolytic nickel and pure wire filament grade tungsten. The ingots were soaked for 16 hr at 1300°C in a hydrogen atmosphere furnace, then swaged at this temperature and finally drawn to 0.020 in. diam wire. Some of the bar stock was retained in 1/2 in. diam rod for hardness and metallographic studies. Wire samples for diffraction work were sealed in evacuated quartz tubes and subjected to the various solution and aging heat treatments in a hydrogen furnace. X ray photograms were taken in a Debeye-Slierrer camera using copper K radiation filtered by nickel foil. Results X RAY DIFFRACTION The lattice parameters of the alpha and gamma phases at saturation were determined by an X ray photogram of the 19.8 at. pct W alloy after solution heat treatment at a temperature well within the alpha-gamma range above the peritectoid temperature (17 hr at 1150°C—oil quenched). The alpha phase was found to be face-centeted cubic with a. of 3.594 ± 0.001?, while the gamma phase was determined as body-centered cubic with a. of 3.158 ± 0.001?. Exactly the same phases and parameters were ohtained with the 17.6 at. pct W alloy for the same solution heat treatment. Thorough analysis was made of an X ray photogram of a 19.8 at. pct alloy sample in the quenched and aged condition (solution treated 1T hr at

Jan 1, 1950

By T. A. Wright

The sampling of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or ('metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can be readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also. As a matter of fact, we may expect that improved refining processes will make possible the partial recovery of lead and tin which are now lost.

Jan 1, 1928

By William H. Mount

St. Joe Minerals Corp. has a long operating history of utilizing rubber-tired, trackless mining equipment in its Southeast Missouri Lead Belt underground mines. The company's first completely trackless mine, Hayden Creek, was opened in 1952, employing rubber-tired drill jumbos, electric shuttle cars, and articulated diesel trucks. The trucks were comprised of a conventional scraper tractor unit matched with a rear-dump rock wagon. These machines featured the first true earthmover tires to be used underground by St. Joe. The articulated truck concept proved to be very successful, and constitutes an increasing portion of the underground haulage today. St. Joe's second completely trackless mine, the Indian Creek property, was opened in 1954; conventional 9.1-t (10-st) rear dumps were used for haulage. Main haul roads were designed to be wide and fairly level to accommodate speeds of 32-40 km/h (20-25 mph).

Jan 4, 1976

By David A. Thomas, John F. Peck

Fibrous microstructures and their development have been studied by metallography and by hardness and quantitative metallographic measurements. Thin, curved grains were observed in transverse sections of commercial tungsten wire and were developed in laboratory-drawn iron wire at reductions greater than about 70 pct. The unusual grain shapes are attributed to the nonuniform mode of deformation of the grains associated with the characteristic [I101 preferred orientation that develops in bcc metals during drawing. Transverse sections of heavily swaged iron wire showed a ospiral nebulao structure that appears to result from the elliptical shape of the cross section of the swaging dies and their rotary motion. Hardness and quantitative metallographic results show unusual trends that parallel the changes in microstructure. Other phenomena are considwed in light of the results, including the strength of fine wires of bcc metals, ocylindricalo textures, and the ductility of fibrous tungsten. 1 HE microstructure of tungsten wire in a longitudinal section shows grains highly elongated in the working direction, giving the appearance of a bundle of parallel fibers, Fig. l(a). Wires of tungsten and other bcc metals show a pronounced preferred orientation in which a [I101 direction is parallel to the wire axis.l The microstructure and texture of tungsten develop during warm working (working above room temperature but below the recrystallization temperature) into wire by swaging and drawing. Fibrous tungsten so produced has limited but useful room-temperature ductility, whereas annealed tungsten is brittle at room temperature. During an investigation of the effect of recovery annealing on the substructure of commerical 0.030 in. diam tungsten wire, it was found that transverse sections of the as-received material showed thin, curved grains, Fig. 1(b), instead of the expected equiaxed grains. The fact that Figs. l(a) and (b) show different sections of the same material at the same magnification is at first disconcerting, because the long dimension of the curved grains in the transverse section is several times the average fiber width in the longitudinal section. However, a longitudinal section cuts most of the curved grains across their narrow dimension, giving the appearance of a multitude of narrow fibers. On the other hand, the plane of a longitudinal section occasionally includes a long dimension of a curved grain, resulting in a broad ofibero, such as A in Fig. l(a). EXPERIMENTS AND RESULTS To investigate the origin of fibrous microstructures and particularly the unusual transverse-section structure of tungsten, rods of iron (also bcc) were drawn and swaged in the laboratory. One rod of annealed Ferrovac E was drawn in six steps to a total reduction in area of 87 pct (0.10 to 0.036 in. diam), and a second rod was swaged to the same reduction, using approximately the same reduction steps. Longitudinal and transverse sections of the swaged and drawn iron wires are shown in Fig. 2, for reductions in area of 39, 73, and 87 pct. A fibrous microstructure in longitudinal section is first evident at 73 pct reduction, and it is further developed at 87 pct reduction. The grains in transverse section remain equiaxed until about 73 pct reduction, when they become somewhat elongated and curved. At 87 pct reduction, the drawn wire shows thin, curved grains in the transverse section, similar to those observed in tungsten. The transverse sections of the iron wires swaged 83 and 87 pct reduction in area show the striking ospiral nebulao structure in Fig. 2(d). This struc-

Jan 1, 1962

By R. B. Woodworth

In the sinking of bore holes, there are but two fundamental operations —drilling and hoisting—which determine in the main the character of drilling mechanism and structures. There are endless ramifications, however, in the execution of these fundamental operations, according to the purposes for which the bore holes are drilled, their maintenance after completion, the protection and convenience of workmen, etc. The three main lines of use for bore holes are in mineral exploration, the sinking of water and salt wells, and the exploitation of pqtroleum and natural gas. This paper has to do more especially with the last. Here again there are many divergences. Wells may be drilled by either the percussive, the hydraulic, or the abrasive method. Finally, each of these methods, as applied by drillers of diverse nationalities, has followed somewhat different lines of development. The American system of cable-tool drilling has perhaps had the widest application; the hydraulic rotary is also in extensive use; but the Canadian system, the Galician system, and the Russian free-fall system all have their points of recognized merit and are preferred by operators accustomed to their use. These differences in drilling procedure, which rest ultimately on essential variations in geological conditions, are reflected in the drilling structures as well as in the drilling mechanism. The purpose of the present paper is to record those stages in the development of the application of steel to the construction of drilling mechanism and structures with which the writer has been intimately associated, and to contribute to the history of the art of drilling other data acquired in the course of his personal investigations. It is necessarily limited by reason of space to American practice, with especial reference, therefore, to the cable-tool system and the hydraulic rotary method of drilling wells for oil and gas.

Jan 1, 1916

By L. Leibowitz, M. G. Chasanov, L. W. Mishler

A drop calorimeter system is described for use in measuring enthalpies to 3600°K. Data are presented for tungsten between 2800" and 3600°K. The enthalpy of tungsten in cal per mole between 2000° and 3600°K can be represented by the equation HºT- Hº298 = - 1.7622 X 103 + 5.7772T + 8.9861 where T is in degrees Kelvin. A tabulation of com -puted values is presented for heat capacity, entropy, and free energy function. A drop calorimeter has been constructed to carry out enthalpy measurements at temperatures to 3600°K. Samples are heated by induction1 and dropped into a commercial adiabatic calorimeter, modified for this purpose. The experimental temperature is limited by the melting point of container materials and compatibility of the container and its contents. Several high-temperature drop calorimeters have been described in the literature1-5 but none has been used at temperatures as high as those in the present work; our measurements of the enthalpy of tungsten range from 2800" to 3600°K. DESCRIPTION OF EQUIPMENT An overall schematic view of the equipment is shown in Fig. 1. Power for the induction coil is supplied by a 25-kw 250 kHz Ther-Monic generator coupled to an iron core RF transformer. The Sample capsule is suspended in the work coil by 10-mil diam tungsten wires which are wrapped around a horizontal 5-mil diam tungsten wire. The horizontal suspension wire is clamped between two massive copper electrodes which are fixed in an x-y motion device that allows adjustment of the position of the heated capsule from outside the vacuum chamber. The copper electrodes are connected by flexible copper straps to a 1250-joule (5 kv, 100 pfarad) condenser bank. When it is desired to release the capsule, the condensers are discharged through the horizontal suspension wire causing it to vaporize rapidly. Very reliable and precise release of the capsule is achieved in this manner. Experiments have shown that no heat correction is required for this discharge energy. As part of the temperature measuring system, two prism holders have been incorporated in the apparatus. The upper prism holder is in the main vacuum chamber itself, whereas the lower one is in a side arm attached to the drop tube below the gate valve. The upper prism is mounted on a rotary vacuum feed-through, and may be moved under a protective shield when not in use. This prevents deposition of vapors on the prism surfaces when temperature measurements are not being made. Similarly, the lower prism is mounted on a push-pull vacuum feed-through, and when not in use may be pulled into its side tube. The prism mountings are fitted with guides and stops so that they may be moved precisely into the desired position. The aim throughout is to minimize the time the prisms are exposed to vapors from the hot samples. At the high temperatures reported in this paper, only the lower prism was used. The upper prism holder in these cases was fitted with an additional radiation shield. By using a prism and viewport, the lower surface of the samples can be observed by an optical pyrometer. The measurements discussed in this paper were obtained with a Leeds and Northrup 8622-C-S series manual pyrometer which is estimated to be accurate to 0.5 pct. Pyrometer calibrations and prism and window corrections were carried out in the conventional manner6 using tungsten strip lamps calibrated by the National Physical Laboratory, Teddington, England. Prism corrections were rechecked after each use. All work to date has been done in vacuum, and no measurable change has been observed in the prism correction below -2300°K for the upper prism and below -2800°K for the lower one. The total time of exposure of the prisms is about 50 sec per run. At high temperature, the final temperature reading is corrected by using the final A value for the prism; see Ref. 6 for details of this procedure. The calorimeter is a modified Parr Instrument Co. (Moline, lll.), Series 1230 adiabatic calorimeter with automatic jacket control. Other authors5 have used a similar calorimeter with good results. The calorimeter jacket cover and calorimeter cover are attached to the drop tube which contains a radiation shield. This shield is a gold-plated copper disc which can be operated manually from outside the calorimeter. The receiver is attached below the radiation shield and is lined with tungsten. In a typical experiment, the calorimeter and its jacket water temperatures were adjusted to 0.000°K temperature difference. The sample was allowed to equilibrate in the furnace at the desired temperature for about 20 min. The initial calorimeter temperature was then recorded, the sample dropped, and appropriate shutters closed. After about 3 min, the drop tube and receiver were filled with helium to 60 torr. The final calorimeter temperature was recorded after it had remained constant over a 5-min period. The equilibration time in the calorimeter was about 25 min. Thermistor probes are used to operate a hot and cold water supply system to maintain the jacket temperature equal to the calorimeter temperature. For actual measurements of the calorimeter temperatures, a quartz thermometer was used (Hewlett Packard Dymec Thermometer, Model #2801A). This thermome-

Jan 1, 1970

By H. E. Criner, M. G. Driessen

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D ,41 Elimination efficiency, in the terminology of Dahl-strom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By M. G. Driessen, H. E. Criner

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D ,41 Elimination efficiency, in the terminology of Dahl-strom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By C. T. Eddy, R. W. Drier

The conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in properry. or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest. Effect of Direction of Drawing In 1928 some work was done on hard-drawn copper wires to determine whether wire drawn in a continuous machine (that is, all in one direction) would have a different structure from wire that had a reversal in direction at some stage of the drawing process. The diffraction spectra obtained indicated that as the position of the wire rayed approached the core, a preferential crystal orientation existed, and that the closer to the core the more preferred was the orientation. The data obtained partly corroborated the work done by Schmidt and Wassermanl and by Clark.2 Samples Used in Following Investigation The samples selected for use in both the diffraction work and the resistivity measurements were taken from Nos. 6, 8, 10 and 12 gage

Jan 1, 1930

J. L. CHRISTIE, Chairman T. S. FULLER, Past-chairman W. M. PEIRCE, Vice-chairman W. A. SCHEUCH, Vice-chairman E. M. WISE, Secretary International Nickel Co., Bayonne, N. J. W. M. CORSE, Treasurer Executive Committee H. A. BEDWORTH G. O. HIERS D. K. CRAMPTON R. H. LEACH E. H. DIX, JR. R. F. MEHL J. A. GANN J. WALTER SCOTT' JEROME STRAUSS Finance Committee T. S. FULLER, Chairman W. M. CORSE H. S. RAWDON C. H. MATHEWSON SAM TOUR

Jan 1, 1934

By Robert E. Green, Kenneth Reifsnider

Several experiments have been performed in order to illustrate the application of a recently developed X-ray image intensifier system to metallurgical investigations. In the present work the system has been used to study the instantaneous alterations in Laue transmission X-ray diffraction patterns during tensile deformation of aluminum single crystals. Expem'mental results are presented which demonstrate the capability of the system for crystal orientation, for following orientation changes due to lattice rotation during tensile deformation, and for showing changes in the homogeneity of the lattice planes along the specimen length as a function of strain rate. RECENTLY, a new X-ray system has been developed which incorporates a cascaded image intensifier and permits direct viewing and recording of X-ray diffraction patterns produced on a fluorescent screen.1"3 In the present work the results of several experiments are presented which demonstrate the usefulness of this system for metallurgical applications. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental arrangement is shown in Fig. 1. In this system a Machlett AEG-50-S tungsten target X-ray tube, normally operated at 50 kv and 40 ma, serves as the X-ray source. The X-ray tube is placed in direct contact with a 10-in.-long collimator, which transforms the X-ray beam from one with a circular cross section to one with a rectangular cross section 3 in. high and 1/6in. wide. By blocking off all but a small portion of the rectangular slit, it is possible to work with the more conventional "pinhole" collimated X-ray beam commonly used for obtaining Laue diffraction patterns. In the present work the test specimens were 99.99+ pct aluminum single crystal wires & in. in diam and 3 in. long. For the deformation tests the wire crystals were mounted in a special set of grips in a table model Instron machine so that diffraction patterns could be recorded during specimen deformation. For the orientation tests the wire crystals were mounted in a rotating goniometer so that diffraction patterns could be recorded during specimen rotation. At a distance of 3 cm from the specimen axis, a 6 in. diam DuPont CB-2 fluorescent screen is positioned to transform the X-ray image to a visible one. A Super Farron f/0.87 72 mm coupling lens, corrected for 4 to 1 demagnification, transmits the visible image to the image tube. The image intensifier used is a three-stage magnetically focused RCA type C70021A with an S-20 input photocathode and a P-20 output phosphor. The tube has unity magnification and useful input and output screen diameters of 1.5 in. The image on the output phosphor is of sufficient intensity to be viewed directly, to be recorded cine-matographically, or to be displayed by vidicon pick-up on a television monitor. The recording device most commonly used is a 16 mm Bolex motion picture camera fitted with a Canon f/0.95, 50 mm lens. The overall gain of the system is 16,000 for direct viewing and 2240 for recording on 16 mm movie film. The resolution of the system is limited to 1 line pair per mm which is approximately that of the fluorescent screen. This system has been used for cine recording of transmission Laue X-ray diffraction patterns with exposure times as short as 1/220 sec and for vidicon television pick-up and display at a scan time of 1/30 sec. Quantitative information may be obtained from each frame of the movie film, by either stopping the vertical slit down to a point source in order to obtain a conventional Laue photograph or else by retaining the linear beam and introducing fiducial marks as described in a previous paper.4 In either case, each frame may be enlarged to appropriate size for analysis by either using a photographic enlarger and making prints of the desired frames, or, more conveniently, by using a microfilm reader. EXPERIMENTAL RESULTS The first series of photographs which are presented in Fig. 2 serves to demonstrate the usefulness of the system for crystallographic orientation determination. This series of prints, made from enlargements of a 16 mm movie film, shows the dynamic Laue transmission patterns produced by an aluminum single crystal wire which was rotating about the wire axis when the patterns were recorded. The movie films were taken at 16 frames per sec and the crystal was rotated at a rate of 15 rpm.

Jan 1, 1970

By A. H. Bell

DEEPEST hole in the earth, and deepest producing oil well in the world-such is well No. K.C.L. A-2, of the Continental. Oil Co., completed on April 12 in the San Joaquin valley about four miles west of Wasco, Calif. It penetrated the earth's crust to a depth of 15,004 ft.- almost three miles-a depth that exceeds by over 2200 ft. that of the previous record holder in western Texas. It is now producing oil from sands at a depth from 13,092 to 13,- 175 ft., which is about 1500 ft. deeper than the record formerly achieved in Louisiana. Continental's new well was bottomed in what is possibly Domengine-Avenal Eocene sand, and is producing from the Middle Miocene equivalent to the Rio Bravo sand.

Jan 1, 1938

NEW YORK MEETING PAGE Winchell, H. V.-Geology of Pachuca and El Oro, Mexico. Discussed by Frederick MacCoy, Robert Hawxhurst, Jr 2 WILKES-BARRE MEETING Kynor, Herbert D.-Mechanical Mining of Anthracite. Discussed by C. Evans, Jr., S. J. Jennings, W. J. Richards, Geo. S. Rice, and the author 3 Stein, C. H.-Ashley Planes for Handling Freight Traffic. Discussed by Graham Bright, Douglas Bunting, S. J. Jennings, R. V. Norris, C. H. Strange, Edwin Ludlow, W. J. Richards, and the author 3 Markle, Donald.-Anthracoal: A New Domestic and Metallurgical Fuel. Discussed by William Griffith, Edwin Ludlow, E. M. Chance, Charles Dorrance, E. W. Parker, G. H. Ashley, C. A. Burdick, Geo. S. Rice, and the author :.. 7 Griffen, John.-Slush Problem in Anthracite Preparation. Discussed by Henry Flood, Jr 11 Eavenson, H. N.-Lynch Plant of United States Coal and Coke Co. Discussed by E. V. d'Invilliers, C. Evans, Jr., Graham Bright, Geo. S. Rice, Geo. Otis Smith, A. M. Rodgers, C. T. Starr, C. A. Burdick, and the author 15 Bunting, Douglas.-Mine Fires Extinguished by Sealing. Discussed by Geo. S. Rice, J. B. Warriner, H. H. Otto, Edwin Ludlow, E. M. Chance, F. B. Nold, H. M. Chance, W. L. Jacobus, J. A. S. Ritson, R. D. Hall, Geo. S. Rice, and the author 18 Bright, Graham.-Determination of Electrical Equipment for a Mine Hoist. Discussed by F. L. Stone, Geo. S. Rice, L. F. Mitten, and the author 34

Jan 12, 1921

By W. H. Bassett, C. H. Davis

The late J. P. Sparrow, chief operating engineer of the New York Edison CO., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40,70-30,80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started on Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period. Plan of Procedure In general, the procedure was to inspect the tubes at short intervals and to remove those that had begun to leak. The tubes removed were carefully examined and a photographic and microscopic record of the

Jan 1, 1925

By C. Morrow

Deformation studies were performed on tuffaceous rocks fran Yucca Mountain, Nevada Test Site to determine the strengths and coefficients of friction under confining pressures from 10-50 MPa at room temperature. Frictional strengths of 30ºsawcut samples increased with pressure and reached values of around 150 MPa at the higher confining pressures. However, the failure strengths of the intact samples were quite unpredictable. The coefficients of friction ranged between 0.7 and 0.9 for all specimens. These data can be used in conjunction with in situ stress measurements at Yucca Mountain, to evaluate the potential for earthquake activity in the region.

Jan 1, 1984

By Walter Harvey Weed

CONTENTS. [ ] INTRODUCTION. THIS paper deals with certain ore-deposits whose structural features or mineral contents (or both) result, directly or indirectly, from igneous intrusions and their after-effects. It is largely a discussion of contact metamorphic ore-deposits based upon the physical changes in rocks due to contact action. It involves a classification of ore-deposits only so far as is abso-

Jan 1, 1913

By M. R. Campbell

Coal is the geological product of entombed vegetal tissues. This view of its origin led Stopes and Wheeler to define it as "mummified plants." They evidently intended this term to be used in a broad way and to mean the preservation of the organic material, as such, regardless of the means employed to accomplish the purpose. The term " coal" should be regarded, therrfore, as broadly generic, and applicable to all accumulations of vegetal tissues as soon as they are covered and protected either by water or by earthy material. In this sense peat should be regarded as the first stage of coal formation and the term coal should include the resultant products of transformation in all other stages of the process until they have lost all resemblance to the original matter from which they were derived. If this idea of the development of coal is accepted and it is admitted, as the geologists claim, that the forces which produced this transformation of the coal have been active since vegetation began to grow upon the land, and are still in operation, it is obvious that somewhere in the world there are all gradations of this material from peat just forming in the swamps of today to graphitic anthracite which presumably marks the most advanced stage that can be recognized with certainty as belonging to the series. Some of these coals, particularly those occurring in the upper part of the series, are fairly well known because they are the ones that are most widely distributed and have been mined and utilized most extensively. On the other hand, the coals in the lower part of the series are but little known because they are not so abundant and, owing to their relative inefficiency, have been only slightly exploited and utilized, especially in regions where the better coals are abundant. The result of these conditions is that much research work has been done on coals of the higher ranks and a great body of facts regarding their physical and chemical properties and the uses to which they are best adapted has been accumulated, but little information is available regarding the coals of the lower ranks. Many able scientists, particularly chemists, have attempted to bring some order of the chaos of coals of various compositions and uses by

Jan 1, 1930