Search Documents

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

By J. E. Burke, C. W. Mason

IN attempting to study precipitation from a tetragonal lattice using solid solutions of bismuth in tin, it was found that although a Widnmanstatten pattern is observed 1 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process MICROSCOPICAL STUDIES Alloys were made from Chempur tin (Standard samples 42b and 42c, National Bureau of Standards), and bismuth (Kahlbaum C P ) by melting neighed quantities together under palm oil, stirring well, and casting in a heated graphite mold The polishing and etching techniques employed largely govern the visibility of the structural changes The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through BehrManning 3/o abrasive papers, lubricated by a solution of paraffin in kerosene A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution, repeated etching and polishing served to remove disturbed metal For high-power examination better preparation was necessary It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a Heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use A better procedure was as follows The metal lap was warmed slightly, and a 4-in circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C was poured over it, allowed to stand for 1 to 2 min and then washed off It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample The cloth was then charged with a paste of the relevigated alumina in water Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deteriorates after about 24 hr This is not serious, because a new lap can be prepared in about 5 min, and only small pieces of cloth are used Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer For the final etching, the most satisfactory reagent was that of Taffs,7 the formula for which is FeC13 6H20, 2 grams, HC1, 5 c c , H2O, 30 c c , C2H5OH (95 per cent), 60 c c This etchant reveals differences in com-

Jan 1, 1941

By M. A. Hosmer, Job Goostray, R. F. Harringon

In this paper, as in so many discussions of an historical nature, there is little chance for original material and much has had to be rewritten from older papers, documents, accounts, reports, and the like, some of which are of doubtful authorship or contain conflicting statistics. Fully aware of these pitfalls, the authors have tried to quote the origin where possible, and also to seek further confirmation when the statement warranted it, but they cannot assume responsibility for certain facts and dates. The Encyclopedia Britannica was frequently consulted. The authors wish to acknowledge assistance from Mackintosh-Hemp-hill Co. (formerly the Fort Pitt Works) and also from officials of the Watertown Arsenal who loaned valuable books and gave much necessary information. They are particularly indebted to Colonel Dickson of that institution. The data on modern guns were furnished by Mr. F. Brauer of the Watertown Arsenal; Mr. H. S. Chaffee assisted by obtaining records and data of work carried on by the Builders&apos; Iron Foundry of Providence, R. I. Three Epochs in History of Cannon Among the great industries of New England, the manufacture of iron was the first to receive attention. Iron ore in considerable quantities was known to exist within the territory of the Massachusetts Bay Colony; and as early as 1629 some steps appear to have been taken toward the manufacture of iron by the Court of Assistants in London, under whose patronage the colony was founded. During the next ten years, deposits of bog ore were found in numerous ponds in the Plymouth Colony; and, in 1652, iron manufacture was begun at Raynham. The "Old Colony" was known as the main seat of this industry in New England, out of which grew a concern which was later to become one of the principal

Jan 1, 1925

By J. S. Marsh

AN incomplete statistical analysis performed wearily on the morning after Thursday, Feb. 12, indicates that the unavoidable items of conversation among steelmen were the current shortage of sleeping time and the "Normandie." No analysis is needed, however, to be certain that many thousands of valuable words were uttered, both in and out of technical sessions, concerning matters of deep interest to members of the Iron and Steel Division. The opening session consisted mostly of papers that have appeared, or will appear shortly, in Metals Technology. One, however, that was not finished in time to be printed in any form, but that aroused great interest, was by E. L. Ramsey and L. G. Graper (Wisconsin Steel Works). Its subject was the production of high-sulphur steel by treatment with sulphur dioxide derived from anhydrous sodium sulphite or bisulphite added to the ladle or to the mold. The sulphide distribution in the finished steel is such that increased machinability and longer tool life result. Both items are of obvious importance in these days of mighty production.

Jan 1, 1942

By SIDNEY ROLLE

ACURSORY glance through the literature on the subject reveals that the ablest minds in the land are devoting themselves to the great question of labor, of which employment is one of the fundamentals. Volumes have been written and the end is not in sight. Employment management is today about in the position that efficiency was 15 years ago. During the early days of the war, and perhaps for a year or so before, labor was plentiful. As the war progressed and Europe drew on us for munitions, employers began to compete with one another for&apos;, all, classes of labor. Labor was difficult to obtain, wages rose, the labor turnover increased, and employers began to install employment departments, welfare plans, and all sorts of schemes, but the labor efficiency dropped. As the war progressed, greater and greater production was demanded. New factors were introduced each day. The government, labor unions, industrial councils, all tended, it seemed, to make the situation almost intolerable. Wages rose to fantastic heights, the cost of living rose higher and higher, and the efficiency dropped still further.

Jan 1, 1921

By William P. Shinn

Jan 1, 1880

By L. R., McLeod

NO important changes in metallurgical practice are exhibited in the smelter that has been erected for treating the Morenci concentrate: the material is charged to reverberatory furnaces without roasting, and the matte subsequently blown in Peirce-Smith converters to separate the iron and sulphur from the copper. In fact the process is essentially the same, except for preliminary roasting of the concentrate, that was adopted in the new smelter that was built for the Arizona Copper Co. at Clifton, a few miles away, to treat Morenci concentrate just before the start of the first World War, and which went into service in October, 1913.

Jan 1, 1942

By AIME AIME

Gentlemen, we have ten questions on our list and a number of us here probably have other questions to ask. Therefore, we arc going to allocate the time to these different questions so that we will try to be finished by 4:30; from then until 5 o&apos;clock, if any of you have any questions on subjects not related, you will be free to ask them. Mr. Morton and I have changed the order of the questions. Instead of what is now first, we have put No. 3 first, progress on basic-roof construction, inasmuch as we feel that it is quite important. At this time, H. S. Robertson, of Harbison-Walker, is going to give you a short talk, with slides, on what has been done to date on this subject.

Jan 1, 1940

By J. J. Beeson

For the past fifty years or more, the structural features of the Cordil-leran mountain system of western United States have presented some most interesting problems. Any geologist or engineer living in this region, or even making occasional examinations of the mines, will lose much of interest and importance if he is not familiar with the literature. Some of the greatest works on geology have been the result of studies carried on in sections of this region. Among the more important of the earlier works are those of Dutton,l King,2 Gilbert3 and Powell;4 of the more recent Lindgren,5 Ransome,6 Spurr,7 Butler8 and others have contributed much. Many of the papers are largely of scientific interest but even these lay the foundation for the commercial application of the broader features of the geology. I have read many of these works with the keenest interest and pleasure; in fact, some have been read until some of the more important findings seem to be my own. In this paper, however, it is my aim to accept credit for little more than the labor of assembling some of the ideas of others. This is done with the hope that an interesting and valuable discussion will be the result. If some of the ideas presented should

Jan 1, 1927

By Robert M. Dreyer

AGGREGATE With an annual domestic production of over 1.6 billion tons at a value of over $2 billion (see Table 15.1.1), the production of aggregate (crushed rock, sand, and gravel) is a basic industry of utmost economic importance. Because of the role of aggregate materials as essential ingredients of concrete, asphalt surfacing, and plaster, their delivered prices are major factors in determining the cost of construction. The annual domestic production comes from nearly 10,000 plants. About 15% of these plants account for over one-half the production. In a rapidly inflating economy, the average mine sales price of aggregate has remained relatively stable. The actual mine sales prices, however, vary greatly depending on quarrying costs in various parts of the country. Of much more importance in construction costs, however, is the delivered price of aggregate. This varies for each job, depending on the distance from the quarry and resulting transportation costs, as well as the initial cost at the mine. Because of a proliferation of regulations limiting new quarries in the vicinity of the encroaching urban sprawl, the average distance which aggregate must be transported has been increasing rapidly. Although it is impossible to derive an average delivered cost for aggregate, it should be noted that even an increase of only $1 per ton in average delivered cost over the last decade (probably a minimal assumption) would mean an annual cost $1.5 billion higher than ten years ago. In recent years, structural engineering considerations, as well as an increasing use of lightweight concrete blocks, have resulted in a rapidly increasing demand for lightweight concrete and plaster, the essential ingredient of which is lightweight aggregate. Principal lightweight aggregates are: pumice, slag, perlite (thermally expanded hydrous volcanic glass), vermiculite, and expanded shale, formed by the thermal expansion of shale and slate. The United States now has the capacity to expand, annually, over 13 million tons of shale and slate and to expand over 600,000 tons of perlite. In locating a site for aggregate production. the following factors must be considered: (1) tonnage available; (2) quality of aggregate (including local variations); (3) distance from major use areas; (4) transportation costs, including those resulting from present and possible future haulage restrictions; (5) zoning regulations; (6) operating costs, including the cost effects of compliance with local regulations governing blasting, air pollution, water pollution and drainage, noise levels, and operating periods. At one time, locating a suitable site for the production of crushed rock, sand, or gravel, in most areas, was regarded as an extremely simple task. In the past few years, however, finding a site for profitable production of aggregate has assumed ever-increasing com-

Jan 1, 1976

By O. F. Kammerer, W. E. Miller, D. H. Gurinsky, J. Sadofsky, J. R. Weeks

Zirconium and titanium inhibit solution mass transfer of steels by liquid bismuth, mercury, and lead. It is shown that in bismuth and mercury, these adsorb on the surface of the steels and subsequently react with nitrogen and possibly carbon from the steels to form inert, adherent surface layers of ZrN, TiN, or TiN + Tic. Data are presented which describe the condition under which thase deposits form. These inhibitors decrease the solution rate of iron into bismuth, and require a higher supersaturation for precipitation of iron from bismuth. USE of the low-melting heavy metals (bismuth, lead, mercury, and their alloys) as coolants has been limited because solution mass transfer of steels occurs in these liquids; i. e., iron dissolves in the hot sections of the heat transfer circuit and deposits in the colder sections. The rate of solution of iron and the temperature coefficient of solubility are sufficiently great to cause complete or partial stoppage by the deposition in the coldest section of a closed circuit in finite time, even though the actual solubilities are extremely low. In the development of the mercury vapor turbine by the General Electric Co., Nerad and his associates1 discovered that the addition of as little as 1 ppm Ti or Zr to magnesium-deoxidized mercury reduced the mass transfer of ferrous alloys by mercury to a negligible amount. Reid2 reported that titanium was detected chemically on the surface of steels contacted with this mercury alloy in amounts varying from 2.0 to 2.6 mg per sq in., the greatest amount being found in the hottest portion of the circuit. Reid stated that the titanium forms the intermetallic compound Fe2Ti by reaction with iron on the surface of the steels. This compound was presumed to be highly insoluble in mercury. More recently, El-gert and Egan3 have reported a greater than 100-fold reduction in the rate of mass transfer of a 5 pet Cr steel by liquid bismuth upon the addition of titanium (in excess of 50 ppm) and magnesium (350 ppm) in the liquid metal, during experiments performed in thermal convection loops* over the temperature differential 700° to 615° C. Also, Shep-ard and his associates&apos; have reported that the addition of titanium to liquid bismuth and Pb-Bi eutec-tic produced a marked decrease in the rates of solution of both iron and chromium from type 410 steel capsules under static conditions. This inhibiting effect increased with repeated reuse of the capsules. Tests performed in this laboratory under carefully controlled conditions have shown that the addition of zirconium and magnesium, or titanium and magnesium, to liquid bismuth or lead greatly reduces the rate of mass transfer of chromium alloy steels and carbon steels in thermal convection loops with a maximum temperature of 550°C.5-9 The present paper will review the data obtained to date at this laboratory on the behavior of iron and steels in contact with liquid bismuth alloys containing titanium or zirconium, and will attempt to explain the role of the above additives in reducing solution mass transfer. Reaction between the Zirconium or Titanium Dissolved In Liquid Bismuth and an Iron or Steel Surface Reaction between Zirconium Dissolved in Bismuth and the Surface of Pure Iron-—A small pure iron crucible (analyzed by the supplier to contain 0.8 ppm N was contacted with bismuth containing approximately 0.1 pet Mg and varying amounts of a radioactive zirconium tracer. The crucible was then inverted at the temperature of contact. The thin residual layer of adherent bismuth was dissolved in cold, concentrated nitric acid. The crucible surface and the solidified bismuth were then analyzed for radioactive zirconium. An analysis of the activity loss on the crucible surface and the weight loss of the crucible during the nitric acid treatment showed that the acid treatment removed the zirconium that had originally been dissolved in the adherent bismuth, but not any zirconium that may have reacted with the crucible surface. The crucible was then pickled in warm aqua regia to remove all surface activity, hydrogen-fired at 600°C, and recontacted with a new liquid alloy. The results of the experiments contacted 1 hr at 450°C show, Fig. 1, a Langmuir-type adsorption with an adsorption free energy of approximately 17 keal per g atom Zr.5 This deposit was estimated to contain 1 atom of zirconium for each 7 to 8 iron atoms on the crucible surface, assuming a surface roughness factor of the pickled crucibles to be five. Increasing the temperature to 520°C caused consi-

Jan 1, 1959

By J. A. Singmaster

A REPORT that it did not pay to use present-day galvanized iron on account of the short life of the material, accompanied by proofs of the state-ment in the form of a tabulated history of the first costs of various kinds of building materials and their main-tenance expense, started an investigation of modern galvanized products. At the very outset it was apparent that our experience with galvanized products was by no means unique. Correspondence with the State Agricultural Depart-ments, the Agricultural Experiment Stations, the County Agents and State Granges all over the United States brought a mass of complaint on this same score. Visits to large buyers of galvanized sheet and wire revealed the same condition coupled with an ever-increasing use of substitutes for galvanized iron. We believe, therefore, that the title of this article is fully warranted by the experience of the consuming public. A study of the proceedings of the various societies having to do with the testing and use of sheet iron and steel products revealed a tremendous amount of work on the life of the base metal itself. Great stress was laid on differences in life of various types of iron and steel, the difference amounting at best to months rather than years. Very little recent attention has been paid to a study of the life of the zinc coating and the causes of its present-day lack of durability. There have been some real exposure studies published, how-ever, which show that the weight of the zinc coating determines the protection afforded by the galvanizing, which is of far greater influence on the life than the base-metal composition. An interesting paper was published by the Phillipine Journal of Science in 1916, entitled: "Galvanized Roofing in the Phillipines," a contribution from the Bureau of Science of the Phillipine Island Government. The author, Mr. Arguelles, found on 18 old galvanized sheets, after from 30 to 35 years&apos; exposure, from 2.3 to 4.1 oz. of zinc per sq. ft. of sheet and sums up the study by saying: Of the various factors influencing the durability of galvanized iron which have been studied with a view towards accounting for the difference in behavior of old and modern sheet, it appears evident that the greater weight of zinc per unit of area on the former accounts for the greater durability.

Jan 10, 1922

By Henri S. Swolfs

INTRODUCTION In this paper we present preliminary results of a research program in site characterization methodology. We are interested in under- standing the response of discontinuous rock to mechanical, hydrologic, and thermal loadings. To carry out such a study we selected a field site with simple geology, uniform distribution of lithologies, and easily verifiable boundary conditions on temperature, fluid flow and stresses. The spatial distribution of fractures at the site was established and tests were conducted to determine the temperature field, hydrology, rock-mass properties, and in situ stresses. As part of the study selected borehole instruments were compared to assess their performance and reliability. SITE GEOLOGY The study area is in the eastern part of South Table Mountain, a mesa near Golden, Colo. The exposed cap rock is a single lava flow of uniform thickness (6-7 m) that rests on the clastic sediments of the Denver Formation (Van Horn, 1976). The surface of the cap rock (N. 75º E., 3º S.) is topographically featureless and slopes south- southeast; drainage is predominantly downdip and punctuated by occasional contact springs. The age of the lava flow is 64-65 m.y., or early Paleocene. Paleo- botanic evidence confirms the upper part of the Denver Formation as Paleocene (Van Horn, 1976). "Rapid-rock" analyses of core samples from the lava flow at three depths (0.2, 3.3, and 5.8 m) suggest a uniform chemical composition throughout with an increase in the Fe2O3/ FeO ratio (1.05 to 1.60) with increasing depth, reflecting the existence of a perched water table in the lava flow, To identify the rock

Jan 1, 1984

By T. T. Read

TWO papers on health and safety were given Thursday afternoon when a joint session of the Health and Safety Committee and the Mining Methods Committee was held. T. T. Read presided and the first paper, on ventilation at Climax, was presented by the author, L. H. Glanville. In the subsequent discussion by Cloyd M. Smith, P. B. Bucky, B. F. Tillson, D. F. Haley, J. L. G. Weysser, and others a number of interesting points not covered by the paper, which appears in full in the January Mining Technology, were brought out. Ventilation troubles in mines so often hinge on the air being too hot and damp that it was interesting to hear of one where it is frequently too cold and too dry.

Jan 1, 1943

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,&apos; has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker&apos;s commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.&apos; Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By Howard I. Young

WHEN so many statements are being made relative to the requirements of zinc metal, it is difficult for some of us who are acquainted with the industry to visualize how it is possible to step up production so as to supply some of the fantastic requirement figures that are published from time to time. I shall attempt to approach this subject from the standpoint of existing conditions which affect production, also keeping in mind the price ceiling under which the industry operates. Total production of primary and secondary zinc in the United States for 1941 will be about 878,000 tons, to which should be added about 36,000 tons of Mexican slab zinc available for consumption or export from the United States, giving a total available of 914,000 tons. Production of slab zinc of all grades in 1942 should be 953,000 tons. Adding the available Mexican supply should bring the total to 989,000 tons.

Jan 1, 1942

FEB. 17-The past month found the average citizen backed off just a little more into his blind corner staring glassily at hydrogen bombs, unbalanced budgets, John L. Lewis, more inflation, a rising wave of strikes, the country&apos;s only active battleship on a mudbank, a famous scientist in gaol as a traitor, a favorite actress on a Roman holiday, and rising mountains of potatoes, butter and eggs begging for destruction. About the only bright spot has been industrial activity and employment, but even these are menaced by the coal shortage. Most industries have orders on hand or in prospect to warrant high operations for some time to come. The trend of the Reserve Board&apos;s production index is upward except as strikes may interfere. There has been heavy buying at the seasonal merchandise shows, particularly in furniture and house-hold goods. The demand for goods of this kind illustrates greater confidence in the Spring outlook than was generally felt a year ago. Further, the demand also reflects improved market positions due to curtailment of output and reduction of inventories in 1949 and sustained consumer buying power. It demonstrates the strong support that is given directly to many businesses, and indirectly to all, by the phenomenal construction activity that is now under way. The Commerce Department places the number of new dwelling units started in 1949 at the new all-time high of 1,019,000.

Jan 3, 1950

By A. E. Seaton

In this paper it will be my endeavor to trace the development of the marine engine and its appurtenances, and the general progress that has taken place in marine engineering generally during the past fifteen years, rather with the object of attributing much of it to the successful efforts of the makers of iron and steel, thereby rendering my thanks to them for the valuable service they have contributed to my profession, than to recount what has been achieved by the skill, ability and perseverance of my colleagues in shipbuilding and engineering. The engineer has been at all times dependent on the ironmaster, and on more than one occasion his progress has been barred by the inability of the latter to overcome some obstacle to success in his manufacture. But on the other hand, it is equally true that the ironmaster has often been ahead of the engineer, and has been prepared, long beforehand, to supply that which would make a success for the marine engineer if he would avail himself of it.

Jan 1, 1891

By Robert J. Linney

IN the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the " 21 " Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. 1, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously developed sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel to footwall and hanging wall to make a bench, spalling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig. 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore; by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1945

By Robert J. Linney

In the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the "21" Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. I, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously devel-oped sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel te footwall and hanging wall to make a bench, spdlling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore, by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1946