Search Documents

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By B Moynihan

The Roa Opencast Coal Mine is situated at the north-eastern end of the Greymouth Coalfield. It lies on an eastern flank of the Paparoa Range, 16 km north-east of the town of Greymouth on the West Coast of the South Island. Road access is via a sealed road from Blackball to Roa, then by a 5.3 km all weather, gravel road, which gains 340 m in elevation from 190 m RL at Roa to a maximum height of 530 m near the opencast.

Jan 1, 1993

By Chris Harnan

This paper describes the geology of three European cities and outlines how the geology has lead to the development of specific foundation construction techniques. Comparative tables of techniques commonly employed are given in Section 5. It can be seen that despite the presence of the &apos;single market&apos;, techniques still have wide diversity despite some similarities in geotechnical conditions.

Jan 1, 2000

By Steve Collinsworth, Nils Heinke

In 1989, I realized the definite need for change in the Blast Hole Drilling Industry. With over 25 years of experience in dealing with the industry, I am well inGormed and educated concerning the problems that occur in Blast Hole Drilling. After continues interaction with the Drill & Blast Superintendents, Drillers, Purchasing Agents, Mechanics, and others in the field, a basic understanding was developed as to the origins of the main problems that the industry f&s with their drillings programs.

Jan 1, 1997

By Tim O’Neil

Caterpillar has introduced its 5090B front shovel, to work with 40 to 70 st (36 to 63 t) trucks. The new unit replaces Cat’s 5080 hydraulic excavator. The 5090B offers more engine horsepower, higher flow, greater digging forces, higher swing torque, faster swing speed and more drawbar pull than its predecessor. It can also handle larger bucket sizes than the previous model. These improvements enhance productivity and make the 5090B a high-volume material handler for hard rock and aggregates producers.

Jan 1, 2003

By E K. Leeka

Process control limitations have led to suboptimal performance of the crushing section of Sishen MineÆs Jig Plant. The performance of the PID (proportional-integral-derivative) controller implemented during commissioning was hampered by the relatively small buffer capacity between the crushers and screens. The inability to maintain the tertiary crushing chamber under full choke conditions lead to inefficient crushing and reduced crusher product cubicity.Model predictive control (MPC) was implemented in the tertiary crusher plant in May 2012 and resulted in a throughput improvement of six per cent in its first month. The controller was further optimised and indicated a throughput improvement of 16 per cent during on/off testing in July 2012. The throughput improvement is attributable to the finer crusher product resulting from operating the crusher under full choke conditions and controlled feed rate to the tertiary crusher plant screens. The next step is to couple the model predictive controller, automated gap control system and an economic optimiser to ensure maximised throughput and value from the resource.CITATION:Leeka, E K, 2013. Performance of model predictive control on the crushing circuit at Sishen Mine, in Proceedings Iron Ore 2013 , pp 417-420 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The kinetic and practical aspects of the extraction of copper from copper-rich solutions by cementation on iron was investigated. Tests were made on the effect of stirring speed, cupric sulphate concentration, acid concentration, temperature, and ferric sulphate concentration on the reaction rate and excess iron consumption.Most kinetic investigations were conducted under a nitrogen atmosphere to prevent any oxidation of the iron or copper metals. The stirring mechanism for all tests incorporated the use of a rotating impeller above a static disc in the solution. The activation energy for cementation on the steel disc at high stirring speed was 8&#183;6 kcal/mole, indicating a predominant chemical control.Increasing the pH first decreased, then above pH 3, increased the reaction rate. Additions of sodium sulphate also significantly increased the reaction rate.The use of high temperature and high pH under an inert atmosphere has been suggested for increasing the reaction rate and producing a high purity sponge copper product.

Jan 1, 1972

By M. R. Smith, H. Kanli

The impact crusher is a popular device for producing crushed aggregates from non-abrasive rocks such as limestones, offering the advantages of high reduction ratios and relatively low installed costs. To extend the application of a process-flowsheet simulator to the quarrying industry, a mathematical model of an impact crusher was therefore developed using the general crusher models of Andersen and Whiten as a basis

Aug 1, 1995

By H. Kose

In this research, a model quarry with an annual production capacity of 1 000 000 tonnes has been studied for both pit and hillside quarry cases with constant overall slope angle and variable bench slope angle, considering road grades of 8 per cent and 10 per cent. First, technical requirements have been determined and then the effect of production parameters, such as hole diameter, type of quarrying (pit or hillside) and road grade, on the cost has been investigated to determine bench height. Based on the results, it has been concluded that hole diameter has to be kept large in both pit and hillside quarrying to reduce drilling unit costs. In addition, in order to take advantage of gravity and reduce transportation cost, it has been suggested that bench height and road grade have to be kept high and low respectively in the case of hillside quarrying (downhill transportation) while, in the case of pit quarrying (uphill transportation), bench height and road grade have to be kept low and high respectively, in order to transport the blasted material to a lower height and distance, to save energy, thus decreasing the transport cost. Keywords: Quarry, pit, hillside, road grade, bench height

Jan 1, 2005

By S. Bellec

A leaching model for gold ore that takes into account the impact of cyanide and oxygen concentrations as well as gold surface exposure on leaching performance is developed. Cyanide consumption is estimated by an empirical model that is a function of ore particles size distribution as well as cyanide, copper and sulphur concentrations. The proposed model has been validated by data from laboratory leaching tests on the Sleeping Giant gold mine ore. Keywords: gold leaching, modelling, exposure surface.

Jan 1, 2009

By G. V. R. Landman

It is self-evident that economic pressure demands that today?s mines stay ahead and stay competitive. The challenge, however, isto find fresh approaches to the pursuit of efficiency and operational effectiveness. Rather than focusing on individual activities in isolation, a process that can lead to poor investment decisions affecting other critical areas of operation, a key concept is optimization of the whole value-adding process of mining. This concept is often called ?mine to mill?. Whereas it is never easy to establish optimal conditions across a whole mining operation, the quality and consistency of the blasted rock strongly affects all operations. In many instances an inability to control rock breaking has been unchallenged, leading to significant investment in time and money to manage the consequences of poor and/or inconsistent rock breaking. This paper discusses how electronic initiation systems can play a major role in optimizing the whole mining operation. Electronically programmed detonators provide not only the ability to tightly control a key parameter, namely timing, but also the opportunity to extract blast data for a continuous improvement process. The ability to alter predictably, using feedback from the downstream processes, blasting variables such as fragmentation, throw, wall stability, and vibration, is a huge advantage. The current understanding of the effect of timing, accuracy, and scatter on rock fragmentation is reviewed and offers reasons why there is significant progress in controlling blast results. Two case studies are examined, which demonstrate the benefits of the technology on the economics of the operations under review.

Jan 1, 2010

By R. Poisel, C. Scavia, Preh A., W. Roth, M. Pirulli

ABSTRACT: Two methodologies for the three-dimensional simulation of the run out of rock avalanches are presented: one based on a granular approach and the other based on a continuum equivalent approach. An evaluation of the possible run out area of the Oselitzenbach landslide (Carnic Alps, Austria) has been carried out applying the two methodologies. The combined use of these two approaches makes it possible a comprehensive assessment of the run out area. RESUME: Deux méthodologies pour la simulation tridimensionnelle de la propagation des avalanches rocheuses sont présentées: la première est basée sur un modèle de type granulaire et la deuxième sur un modèle du continu équivalent. Une évaluation de la propagation éventuelle de l’avalanche de Oselitzenbach (Alpes Carniche, Autriche) a été réalisée en utilisant les deux méthodologies. Les résultats obtenus montrent que la combinaison des deux approches rend possible une analyse plus complète de la phase de propagation. KURZFASSUNG: Für die dreidimensionale Modellierung eines Felsmassensturzes (sturzstrom) werden zwei Methoden, eine granulare und eine kontinuumsmechanische Methode, vorgestellt. Beide Methoden wurden zur Abschätzung der Ausbreitung (runout) der Massenbewegung Oselitzenbach (Karnische Alpen, Österreich) herangezogen. Die kombinierte Anwendung beider Methoden ermöglichte eine umfassende Beurteilung des möglichen Ausbreitungsbereichs.

Jan 1, 2003

By A J. Cornah

Critical decisions in iron ore project evaluation and production are based on global and local spatial estimates of primary mineral deposit properties (such as in situ geochemical grades) and geometallurgical responses (such as screened, washed or concentrated product yields and grades), which are derived from limited sample data. These spatial estimates are typically made using classical geostatistical techniques, which fundamentally assume that the attributes of interest behave additively. This assumption is generally appropriate for æprimaryÆ variables but æresponseÆ variables may behave non-additively and therefore their direct linear estimates may be biased.In this paper an existing additivity testing mechanism is used to quantify the bias resulting from direct linear estimation of a non-additive iron ore attribute. Data from a magnetite project are used to determine the circumstances under which such biases may be of material impact. The implications for iron ore resource estimation, geometallurgical modelling and grade control are outlined and discussed.CITATION:Cornah, A J, 2013. Assessment of the impact of non-additivity in the estimation of iron ore attributes, in Proceedings Iron Ore 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J. T. Jordaan

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree This paper addresses the critical parameters that need to be considered when designing a mechanized bord-and-pillar mining layout for a narrow tabular steep dipping orebody. These parameters are : ?Reef dip ?Reef width ?Geological structures within the orebody ?Physical dimensions of the selection of machines ?Gradeability of the selection of machines. The main objective in designing such a layout is to maximize machine efficiencies whilst minimizing dilution. This methodology was then applied in the design of a mechanized bord-and-pillar mining layout for a given piece of ground (Vlakpoort and Moddergat) using a given selection of machines. This piece of ground contains the PGM bearing UG2 Reef with an average thickness of 124 cm and dipping at 18°withadverse strike and dip changes. Two bord-and-pillar layouts were designed for this area. Layout 1 is characterized by the use of strike conveyors to convey ore on strike with an average LHD hauling distance of 35 m. Layout2 uses LHDs for all on strike conveyance of ore with an average hauling distance of 75 m. These two layouts were then technically and financially compared. It was concluded that layout 1 is theoretically superior but layout 2 was chosen due to its greater flexibility and probability of operational success. Layout 2 was also compared to conventional mining and it was concluded to be more economically feasible. However the latter is a proven mining method in these conditions and has a lower risk operational failure. Bord-and-pillar mining has some favourable promises such as improving labour difficulties, lowering operating costs and providing safer working conditions. The success of mechanized bord-and-pillar mining in narrow tabular steep dipping orebodies will depend on the extent of the research and development efforts which need to create and innovate technologies to overcome some of the current limitations stated in the above-mentioned parameters.

Jan 1, 2003

By P. A. Hacquebard, M. P. Avery

"Gondwana coal deposits are widespread and are known to occur in four continents. They are present in Brazil, India, South Africa, and Australia. From coal petrographic examinations and a detailed literature survey, it is interpreted that Gondwana coals are present also in Canada and the United States. Laurasia, or Northern Hemisphere, coals occur in the United States, Canada, and Europe. They form the main coal producing fields of the world. Megascopically, Gondwana coals have a uniform, micro-banded appearance, with a dull lustre; Laurasian coals are bright and have distinct bands of vitrain and clarain. Petrographically, Gondwana coals, compared to Laurasian coals, are lower in vitrinite, but higher in inertinite, particularly in semifusinite. Mineral matter averages 16% in Gondwana coals and 5.7% in Northern Hemisphere coals.Gondwana coals are characterized by thick seams that terminate through lithification (Versteinerung), whereby coal passes laterally into shale. Laurasian coal seams are thinner and terminate by splitting and digitation.Vitrinite/inertinite ratio data indicate deposition of the Gondwana coals in dry marshes under strong oxidizing conditions. The Laurasian coals originated in wet marshes in a reducing environment. As deduced from fossil plants and fossil spores, temperate and near arctic conditions apply for the Gondwana coals. A tropical and subtropical climate is indicated for the Laurasian deposits. The Gondwana coals were formed under allochthonous conditions. They derived from vegetation that drifted into the peat bogs. The Laurasian coals are autochthonous and originated from vegetation that grew and was buried in the peat bogs. The Gondwana coals are Late Carboniferous and Early Permian. The Laurasian coals are entirely Late Carboniferous."

Jan 1, 2004

By I. Mihajlovic

This paper investigates a potential method for arsenic removal from copper concentrates using hypochlorite leaching. The problems concerning pyrometallurgical processing of copper concentrates with high arsenic contents are discussed. A possible solution to the problem by leaching of natural enargite crystals with sodium hypochlorite under alkaline oxidizing conditions, with enargite converted into crystalline CuO and the soluble arsenic forming AsO43-, was experimentally investigated and results are presented. Kinetic parameters were calculated for enargite leaching, using a model-free approach. Advanced isoconversional methods were used to investigate the dependence of activation energy (Ea) on reaction rate (a). Keywords Enargite, copper concentrate, isoconversional method, kinetics, activation energy.

Jan 1, 2011

By Hudson S. B

With a particular electrode configuration, and a particular combination of electrode voltage and roll speed, a relatively small increase in electrode voltage, or a relatively small decrease in roll speed, resultsin a marked improvement in the separation of zircon from ilmenite. In general, fine minerals can be separated using a higher roll speed, or a lower electrode voltage, than is required to separate coarse minerals. The ionizing electrode should be reasonably close to the point at which mineral is fed on to the roll, and nearer to the roll than the non-ionizing electrode. The optimum conditions for the separation of zircon from ilmenite may not apply for the separation of other non-conductors from other conductors.INTRODUCTIONAlthough the high tension separators used in the Australian beach sand industry are efficient, this efficiency has been gained very largely by a process of trial and error, and not by a systematic study of the effects of changes in the operating variables. The optimum roll speed for a particular electrode position and electrode voltage, and the optimum electrode voltage for a particular roll speed and electrode position, can both be determined quite readily. It is not so simple to determine the optimum electrode position for a particular electrode voltage and roll speed. The reason for this is that the electrode used in high tension separators consists of two parts-an ionizing and a non-ionizing electrode respectively. The angular and radial positions of these electrodes, relative to the feed roll and to each other, affect the behaviour of conductors and non-conductors to varying degrees.

Jan 1, 1962

By S. Kevin McNeil, William Joa, Catherine Johnson, S. Omar Garcia

The geometry of an explosive is known to have a fundamental effect on the resulting shock wave propagation. Typically researchers use a spherical or hemispherical geometry in order to simplify the shock wave so that resultant overpressure and impulse are uniform in all directions. The goal of this research is to understand the overpressure characteristics from a sheet explosive, a geometry often utilized for breeching in the military. In training alone, soldiers can be exposed to several tests per day, which may be contributing to the prevalence of blast induced mild traumatic brain injuries. Using PCB pressure transducers and high speed video, it was found that as the angle departed from normal (perpendicular) to the face of the sheet explosive, the over pressure decreased significantly. When in line with the plane, a decrease of over pressure by as much as 20% was observed. Time of arrival was roughly 20% faster directly in front of the charge with a pressure amplification of 46% relative to a spherical baseline charge of the same mass. This testing may reveal a more complete relationship between the pressure and angle from the explosive that could have applications for military and law enforcement with respect to best practices on blaster location for reduced over pressure exposure.

Jan 1, 2019

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is a very popular applied seismology site characterizing tool within geotechnical engineering. A challenging aspect of DST is to characterize the acquired seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. BCE has invested considerable resources into developing Seismic Trace Characterization (STC), which uses various independent parameters of the acquired data at a particular depth. Initial work in this area resulted in the selection of the linearity estimate from the polarization analysis, the cross correlation coefficient of the full waveforms at the particular depth and the preceding depth and a uniquely developed parameter referred to as the signal shape parameter for this characterization. Subsequent analysis in STC identified two other parameters: the Signal-Noise-Ratio (SNR) and the Peak Symmetry Differential (PSD). The paper briefly describes these parameters and then outlines how they can guide the data analysis to derive more accurate results, especially near surface, which is especially important to assess the liquefaction potential in areas prone to earthquakes, such as California. The process will be illustrated with actual data from another area prone to earthquakes, namely New Zealand. 1. INTRODUCTION The near surface characterization of low strain in-situ shear wave velocities (VS) has proven critical for liquefaction assessment. Liquefaction is a phenomenon in which dynamic loading of saturated soil results in the material properties to change suddenly from a solid state to a liquefied state. VS is an important parameter for evaluating liquefaction potential due to fact that it is influenced by many of the variables that influence liquefaction (e.g., void ratio, soil density, confining stress, stress history, and geologic age (Andrus et al., 1997)). Aki and Richards (2002) also outline that the amplitude of ground motion should depend on the density and shear wave velocity of near surface soils and rocks according to the theory of wave propagation. Since the change in density with the increase in depth is relative minor compared to that of the shear wave velocity, the latter is a very useful parameter to represent site conditions (Stewart et al., 1997). Bray (2014) and his colleagues carried out an extensive geotechnical analysis of the catastrophic liquefaction that occurred in Christchurch, New Zealand in 2010 and 2011 and found that near surface rather than deep liquefaction resulted in extensive foundation damage.

Jan 1, 2018