Search Documents

By Karsten Beckhaus

"Abstract Tremie concrete for special geotechnical works needs special properties, especially during the casting process. Today’s execution standards for bored piles and diaphragm walls, EN 1536 and EN 1538, as well as the draft version of concrete standard EN 206, all comprise regulations for deep foundation concrete which have not been changed for decades. Considering the recent development in concrete technology at the same time and its actual state-of-the-art, it is essential to develop new normative specifications and specification requirements.GeneralTo allow the required integrity and quality after placing and hardening, concrete for structural elements like bored piles or diaphragm walls, used as foundations of high-rise buildings or as retaining structures for large and deep building pits, must have adequate workability and stability.In addition to requirements on mechanical properties and on durability, both of which have increased within the last decades, concrete must be suitable for being cast in deep or extremely deep excavations, see figure 1. Today’s specialist foundation engineering machinery makes it possible to drill or cut down to in excess of100 m depth. Concrete technology has developed and allows the use of high performance concrete for deep foundations. But is this capability represented by actual regulations?It has become very common for the industry to supply or use concrete with low water cement ratios, nevertheless highly flowable and set-retarded for several hours if needed. Very low water cement ratios allow design strength of 60 MPa or higher (Larisch, 2011), and a very low porosity which is required for a long service life in aggressive conditions, e.g. by chlorides.To achieve best performance, it is obvious that the concrete must completely fill the excavation and fully embed the reinforcement. As vibration of deep foundation concrete is (usually) not allowed and was anyway inefficient, deep foundation concrete must be designed to self-compact under hydrostatic pressure. Generally, it must be considered that after placement the concrete’s quality cannot be influenced anymore. Therefore, both the pouring procedure and the concrete quality must be adequate."

Jan 1, 2014

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By I. A. Mwamba

Plain and alloyed titanium aluminides of composition Ti-47.5 at.% Al were prepared by melting commercial-purity titanium and aluminium with additions of 1 at.% precious metal. The as-cast alloys were subjected to potentiodynamic scans in 5, 15, and 25 wt% HCl aqueous solutions at room temperature and compared for their abilities to spontaneously passivate. Addition of precious metals resulted in a general improvement of corrosion resistance by increasing the open circuit potential to more noble values. Addition of 1 at.% gold or silver to titanium aluminide did not significantly increase the corrosion potential (Ecorr) above that of the plain titanium aluminide alloy, indicating that gold and silver are not sufficient cathodic modifiers to improve the corrosion resistance of titanium aluminide in all the solutions tested. However, platinum, palladium, and iridium additions shifted the corrosion potentials to the position of the passive region of plain TiAl for all solution concentrations. This indicated that TiAl alloyed with these platinum group metals would passivate spontaneously by cathodic modification. TiAl alloyed with palladium performed the best in 5 wt% HCl solution with the most positive corrosion potential. In 15 wt% HCl solution, alloys with platinum exhibited the most positive corrosion potentials, while alloying with iridium or palladium revealed more negative corrosion potentials. Thus, palladium alloying led to the best cathodic modification of titanium aluminide in low-concentration HCl solution, whereas platinum and iridium alloying additions resulted in the best cathodic modification of titanium aluminide in high-concentration HCl solutions.

Jan 1, 2013

By R. Franfield

This paper describes a situation that many drilling and blasting contractors have found themselves in – a client?s fear of the use of explosives. In the summer of 2007 Blasting Services Ltd was asked to undertake some drilling and blasting work in an abandoned quarry that was being restored for a housing development. Previous quarrying operations had left a series of overhangs that were considered unsafe and required removing. The site contractor considered that the best and safest way to carry out this work was by drilling and blasting. Blasting Services Ltd, with the technical assistance of Exchem Explosives, designed a drilling and blasting regime to accomplish this work with a series of trim blasts. The design took into account the close proximity of a structure in very poor condition and the imposed vibration limit of 6.0 mm/s (0.24 i.p.s.). The faces were profiled, holes drilled and explosives ordered. A few days before the first blast was due to be carried out the client decided that the poor condition of the nearby structure meant that the use of explosives could not be permitted. This decision was made despite the blast design indicating that the vibration level would be well below the 6.0 mm/s (0.24 i.p.s.) limit.

Jan 1, 2009

By Rony Yupanqui C

El presente trabajo señala el proyecto de remediación de los relaves mineros realizado en la relavera Ticapampa, ubicado en el Distrito de Ticapampa – Huaráz, región Ancash, con el objetivo de remediar los relaves de TICAPAMPA depositados por más de 30 años y que contaminan al río Santa, fuente principal de irrigación del Valle del Callejón de Huaylas. El proyecto comprende la extracción de contaminantes del pasivo ambiental de Ticapampa a través de la flotación de los sulfuros de fierro, y la obtención de un material inerte (con bajo contenido de sulfuros contaminantes) para la fabricación de productos cerámicos por medio de resinas recientemente desarrolladas.

Sep 12, 2011

The metallogenic map of New Zealand shows the distribution of metallic mineral deposits, according to type and size, in relation to their geological setting. The major purpose of the map and accompanying 200-page monograph is to summarise the distribution, modes of occurrence and origins of the metallic mineral deposits of New Zealand. The map demonstrates the prospectivity of New Zealand for metallic minerals, particularly gold, silver, iron, and titanium. Information on each deposit is summarised in index tables based on major geotectonic units or deposit/commodity type. The mineral deposits are arranged and discussed in relation to tectonostratigraphic and tectonomagmatic units or terranes, under broad geotectonic divisions of the Paleozoic to Mesozoic Western Province, the late Paleozoic to Mesozoic Eastern Province, the mid Cretaceous to early Tertiary rifting phase, and the late Cenozoic Kaikoura Orogen. Regions or areas of marked concentration of mineralisation are recognised as metallogenic subprovinces or districts, namely: eastern Northland (Hg), the Hauraki Goldfield (epithermal Au-Ag-Pb-Zn-Cu), the west coast of the North Island (shoreline placer Fe), east Nelson (podiform Cr), west Nelson (porphyry Mo), the West Coast of the South Island (shoreline placer Ti), west Nelson-Westland (placer Au), Reefton (mesothermal Au-quartz veins), and Otago (placer Au and mesothermal Au-W quartz veins).

Jan 1, 1993

By Paul Sarnoff

The economics of precious metals -- depending upon who is involved --could be the economics of hope, of fear, indeed of profit and perhaps survival. For those investors seeking capital gains in a puzzling economy, precious metals involve the economics of hope. Those who are convinced that currency soon won't be worth the paper it's printed on turn to precious metals because of the economics of fear. Gold and silver have been a storehouse of wealth since biblical times. The economics of fear during the past 500 years on the Continent has caused almost every European family to make sure a private stockpile or hoard of gold, silver or coins is at hand in case the paper currency of their country undergoes the kind of disaster that came to the German Mark after World War I. Understandably, for mining companies involved in the production of precious metals, the elements of operations and management are directly concerned with the economics of profit -- and perhaps survival. To the American miner the price of precious metals in the marketplace is a matter of daily concern. After decades of selling silver to the US Government at 64.64 cents an ounce, producing silver mines suddenly became faced with prices breaking $5, $10 and $20 per ounce, and approaching $50 an ounce during the period 1978-1981. What should the miner expect one year in the future? Five years?

Jan 1, 1981

By Daniel H. Israel

Indian tribes own a substantial portion of the West's minerals. More importantly, Indian reservations contain coal, oil and gas, uranium, and oil shale reserves in unusually large and unencumbered blocks. Many tribes are now prepared to intensify development of their large reserves knowing that they can offer energy partners the unique opportunity to develop major energy facilities free of overlapping local, state, and federal permitting authorities. The tribes, therefore, can offer mineral developers both substantial reserves and an unusual degree of freedom from a multiplicity of government regulation. In the past, Indians and energy companies enjoyed only partial success as business partners. Indian tribes lacked the resources and know-how to act as equal partners with large oil and gas and mining operators. The tribes relied on the Bureau of Indian Affairs (BIA) to initiate and execute reservation energy projects, and as a result the tribes never developed adequate tribal structures and the expertise to responsibly manage their energy resources. At the same time industry made little effort to understand and learn the laws, customs, and institutions existing on Indian reservations. To the contrary, industry found it easier to bypass the tribes and deal with BIA officials. But the situation has changed. In 1975 the tribes organized an effective coalition, the Council of Energy Resources Tribes (CERT), which recently acquired substantial federal assistance to bring the tribes a level of technical and business expertise that begins to equal that of industry. Because the tribes have changed the rules of the game, industry must now change and learn to work directly with tribal governments. A working knowledge of Indian law, practices, customs, and policies must be acquired by energy companies before beginning negotiations with tribal governments for development of reservation energy resources.

Jan 6, 1980

By Giovanni A. Bonita

The United States Capitol Visitor Center (USCVC) is one of the largest underground structures ever constructed in the Washington, DC, metropolitan area. The 600,000 ft2 (55,750 m2) structure is entirely underground and immediately adjacent to the shallow foundations of the existing U.S. Capitol building. Interior building columns for the USCVC were supported on 186 drilled shafts that varied in diameter from 4 to 9 ft (1.2 to 2.9 m) and in length from 15 to 45 ft (4.6 to 13.7 m). The vast majority of the building utilities were located beneath the basement floor slab. It was decided at the onset of the project to proceed with construction prior to completion of the design drawings, and coordination between the underslab utilities and the drilled shafts had not yet been finalized at the onset of drilled shaft installation. Given depth and location restrictions of the outlets, relocation of the bulk of the utilities was not possible. Almost half of the drilled shafts were affected, leaving redesign as the most feasible remedial solution. The redesign involved adjustments to the shaft length, diameter, and bell. It took place on a case-by-case basis, sometimes only minutes before installation began. Coordination between the field and design team was excellent, and delay associated with the redesign efforts was minimal. In addition, the detailed, high-quality field records kept by both the contractor and field engineers allowed for accurate and fair estimations of the added drilled footage and concrete volumes placed. The additional service fee, which was minimal, was settled quick and fair.

Jan 1, 2006

By F. T. Wang, Y. Yuan, S. H. Tu, X. G. Zhang

Hydraulic support instability (HSI) is one of the most common causes of disasters in underground coal mining, posing a threat to the safety of mine workers and normal operation of the equipment. It is prone to occur in fully-mechanized mining faces with a large mining height (FMMLMH), especially when the dip angle of the coal seam is large. The key to controlling HSI is to deduce its mechanism and employ effective control techniques. This paper focuses on the analysis of HSI types, the key parameters and techniques to control HSI in FMMLMH, the establishment of a model of HSI in FMMLMH, and a multi-parameter sensitivity mechanical model of different HSI forms in the no. 7219 longwall face in Xutuan Coal Mine, Huaibei Mining Group, by using sensitivity analysis . The results show that HSI mainly presents in three forms: hydraulic support gliding (HSG), hydraulic support tilting (HST), and hydraulic support tail twisting (HSTT). The occurrence of the above three forms depends mainly on support anti-instability capability. In the no. 7219 longwall face, HSG and HST are the main two forms of HSI. The dip angle of the working face and the friction coefficient between floor and hydraulic support are the sensitive parameters for HSG, while HST is strongly dependent on the dip angle of the working face and the friction coefficient between roof and hydraulic support. By the applications of measures such as the oblique layout of the working face, cutting the floor into a step pattern, moving the support under pressure, and raising the setting load, the support stability was controlled effectively.

Jan 1, 2015

By Paul W. Mayne

Axial pile performance can be rationally evaluated within an elastic continuum framework using field results from seismic piezocone tests (SCPTu). Adopting a versatile Randolph-type elastic pile model, the approach can be applied to either traditional top down loading using an anchored reaction beam or the newer Osterberg cell that simultaneously pushes the base and shaft in opposite directions. The axial load distribution within the shaft is also evaluated. For site-specific data at a given site, the SCPTu is an optimal means for collection of subsurface information because it combines penetrometer readings and downhole geophysics in one sounding. The results obtained are at opposite ends of the stress-strain-strength curves, specifically the peak strength for capacity interpretations and the small-strain stiffness (Emax) for evaluating the initial deformations. Axial pile capacity can be analyzed using both direct and indirect CPT methods. As such, the approach allows for a complete representation of the axial load-displacement-capacity curve for pile response. Case studies are presented for deep foundations situated in stiff clays at two national geotechnical test sites located in Houston and College Station, Texas, using top down loading, as well as a third case study of a drilled shaft in clay till loaded by O-cell in Alberta.

Jan 1, 2009

By Akihide Hosokawa

The void growth and coalescence in model materials involving a pre-existing three dimensional void array (i.e. multiple layers of a void array) was studied by X-ray computed tomography (XCT) coupled with in situ tensile deformation. To reduce the recording time, a new technique called fast tomography was employed. The model materials used in this paper were fabricated by the combination of an ultra-short pulsed laser machining system and a diffusion bonding technique, and two different types of arrays were prepared namely, FCC 1 and FCC 2 type array. This methodology allowed the authors to capture the entire process of growth and coalescence events of a void array embedded in the metal matrix. The failures in the both materials involved internal necking and shear localization. One of the highlights of this paper is that the plastic strain at the onset of void coalescence was measured for each model material. These values are in fact the adequate values to be compared with the coalescence strain predicted by existing void coalescence models such as the Brown and Embury model, the Thomason model and the Pardoen and Hutchinson model. The comparison suggested that the Brown and Embury model underestimated the coalescence in neither of the current model materials, while the Thomason model and the Pardoen and Hutchinson model showed a quite good agreement with the result for FCC 1 material. On the other hand the result from FCC 2 material agreed with none of the models probably due to the geometry of the void array that is not compatible with the existing models.

Jan 1, 2010

By Eder Salazar

Como parte del desarrollo de sus operaciones de mina de cobre subterránea, la Sociedad Minera El Brocal S.A., desarrolló el método de minado tajeo por subniveles con pilares recorridas con el fin de incrementar su producción actual. En ese sentido, el presente texto señala la implementación de un método de minado conforme a las características geomecánicas del macizo rocoso del yacimiento.

Sep 12, 2011

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine. Montana Technological University (Montana Tech) obtained a time-domain reflectometer (TDR) type VOD monitoring unit. Purchase of the VOD monitor was justified on verifying explosives performance used in Montana Tech’s practical underground mining class and provide a teaching aid for the school’s rock fragmentation class. Before demonstrating the unit to students, we figured we better learn how to use it first so we give the students an appropriate experience. Our first learning was in obtaining the correct coaxial cable for the VOD monitor and how to properly terminate the cable. Once the cable was on-site and terminated, VOD testing could commence. Use of the VOD monitor was tested underground in small diameter holes (1.5-inch, 38 millimeter) pneumatically loaded with ANFO. After a few failed trials, and follow-up discussions with the supplier, VOD readings were obtained for the ANFO loaded holes. Additional readings were obtained for a pre-split product and detonating cord to satisfy our curiosity that the unit was performing as specified by the manufacturer. This paper will share our learnings in the hopes that others can benefit.

By M. K. Pelser

The purpose of this paper is not so much to provide a scientific study of the selection process for the perusal of other psychometrists or industrial psychologists?the purpose is to provide line management with a practical, relatively user-friendly guide to fair and scientific selection. The main areas that are to be covered are: ? Why fair and scientific selection? ? Job analysis ? The job requirement?selection technique circle ? Assessment centres in the mining industry?the Tavistock Collieries Ltd experience. Why fair and scientific selection? Seen from a line manager?s perspective, fair and scientific selection should be pursued for two main reasons: ? to remain within the ambits of the law ? to maximize the probability of selecting the potentially most productive and efficient candidate for the job.

Jan 1, 1997

The disasters between 1920 and 1979 in coal mines in Queensland and New South Wales due to underground fire, gas or coal dust explosion or to gas or coal outbursts, have been assessed. The evidence relating to disasters caused by gas explosion points strongly to divergence from safe mining practice as the main cause. There is a need for greater training and education of personnel, closer analysis of gas reports, better monitoring and testing procedures, improved ventilation standards and a policy where safe working practice is actively encouraged. Conditions in the New South Wales occurrences of gas explosion were similar to those at Collinsville, Queensland in that dykes, igneous sills, burnt out coal and faulting were common to all. Information on outbursts indicates that contributing factors were intrusions, depth of cover, fault zones and other geological disturbances, methods of work, pressure and type of gas.

Jan 1, 1982

Silver is one of the three major metals produced from the Broken Hill mines. The accurate determination of the silver in these ores, therefore, is of economic importance.With due appreciation of the divergence of opinion of many who are interested in the subject of the determination of silver, the writer has been prompted to present the results of some recent experiments on silver losses during cupellation and conclusions from these experiments in the present paper. The losses of silver in the fire assay for this metal are due to silver retained in the slag during the fusion or scorification of the ore, and to silver volatilized from, and absorbed by the cupel during the process of cupellation.The literature describing the results of experimental work on silver losses due to the above causes is extensive, and the general conclusion of these experiments is that the silver lost in the slag is small, but that lost by cupellation is larger and more variable.The term cupellation loss in this paper refers to the total cupellation loss, no distinction being made between the absorption and volatilization losses.Volatilization loss is shown by King to be 0.5% of the total cupellation loss and, as it is generally accepted among assayers as being only a small fraction of the cupellation loss (3) (5), it will not receive further consideration in this paper.The factors causing the loss of silver by cupellation and the precautions to be obs~rved to reduce the loss in this operation are described in (1), (2), (3), (4) and (5). The...

Jan 1, 1940

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004

By Kanchan K. Sen

The North Shore Connector (NSC) project will extend the Allegheny County Port Authority?s Light Rail Transit System from downtown Pittsburgh below the Allegheny River to the North Shore via twin bore tunnels. Jet grouting, diaphragm walls, and soil mixing were selected as cost-effective technically viable ground improvement and support of excavation techniques. Jet grouting was specified to provide break-out (egress) and break-in (ingress) block sections at the tunnel boring machine (TBM) launching and receiving pits. Jet grout treatment was also used adjacent to buildings with shallow foundations and below retaining walls along the tunnel alignment. A new method for measuring jet grout column diameter based on electrical resistivity was employed on the project. New equipment was introduced in the U.S for constructing soil mix temporary support of excavation using a soil-mix technique termed Cutter Soil Mixing (CSM) due to the use of two vertical cutting wheels that have evolved from diaphragm wall trench cutter technology. The system allows for continuous water tight soil mix panel construction including steel beams. This paper highlights some applications of jet grouting and various support of excavation systems (e.g. slurry walls, cement bentonite walls and CSM walls), including new innovative techniques (e.g. Cyljet and CSM) used under the constraints of an urban environment.

Jan 1, 2010