Search Documents

By E. W. Coderre, R. C. Baxter

"This paper describes the townsite of Wabush and the two railways operated by Wabush Mines for the loading and unloading of iron ore concentrate. The town of Wabush is located approximately 200 air miles north of Sept-Iles, Quebec and is in the Province of Newfoundland and Labrador. Construction of the town-site began in 1961 to provide housing accommodation for the construction force and permanent employees in the mining and milling operations located 4 miles away. Wabush Mines operates two short railway lines in loading and unloading concentrate between the concentrator, located at Wabush, and the pellet plant at Pointe Noire, Quebec. Both of these railways connect with the main line of the Quebec North Shore and Labrador Railway and provide a shuttle service between the two phases of the operation."

Jan 1, 1969

Heap leaching of copper sulphide and oxide ores' has been conducted at Rum Jungle since the end of 1965.A review of operations was made and this led to an examination of some theoretical aspects of copper sulphide heap leaching. Ox,ygen diffusion was indicated to be the factor controlling copper leaching rate at Rum Jungle and in other similar operations. Suggestions are made for measuring the heap leaching rate. Prediction of full scale operational results from pilot scale testwork are discussed.

Jan 1, 1969

By K. E. Gray, M. S. Seth

In Part I of this work,1 equations of elasticity were formulated for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure. Equations of elasticity and the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant rate of pressure or a constant rate of flow is maintained at the wellbore. In this paper, the approach presented earlier is extended to finite reservoirs for the cases of (1) steady-state flow, (2) constant pressures at the well bore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Results of this work show that radial and tangential stress gradients are high near the wellbore but diminish rapidt; away from the well; the vertical stress gradient behaves in the same way but is less severe. Radial stresses are compressive or neutral, whereas tangential and vertical stresses may be tensile, neutral or com-pressive, depending upon the boundary conditions, the physical Properties of the system and the radial distance involved (vertical stresses are always compressive in an unbounded system1. For constant boundary pressures, both radial and tangential stresses increase with time whereas they both decrease for a closed outer boundary and constant pressure at the wellbore. The vertical stress decreases with time for both systems. For steady-state systems, radial displacement may be positive or negative, depending upon the dimensions of the system, the pressure differential and the porosity. Radial displacement may be positive or negative for a closed outer boundary but is positive for constant pressures at both boundaries. INTRODUCTION The importance, utility and complexity of a realistic appraisal of the stress state at and local to a wellbore were indicated in Part I. In this paper the analytical approach presented earlier is extended to finite, cylindrical reservoir geometry for the cases of (1) steady-state flow, (2) constant pressures at wellbore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Other than the outer boundary of the reservoir being finite, the physical system and assumptions pertinent thereto are the same as before. The reader may wish to review the mathematical development through Eq. 49 of Part I before proceeding here. SOLUTION FOR GENERAL BOUNDARY CONDITIONS THERMAL STRESSES AND DISPLACEMENTS Since normal stresses do not exist at the free boundaries of a system subjected to thermal stresses, the boundary conditions are

Jan 1, 1969

By C. A. Komar

The Bureau of Mines conducted oil-displacement tests in the laboratory with three water-in-oil and five oil-in-water emulsions that were created with ultrasonic energy at a frequency of 20 kHz and an acoustic intensity of approximately 100 watts per cm2. Emulsions of either crude oil or kerosine, brine, and 112 to 2 percent emulsifier were formed during 30 seconds of acoustic irradiation. Results indicate that ultrasonic energy induces greater and more uniform dispersion of one liquid in another in the presence of small amounts of chemi¬cal emulsifiers. When the emulsions were injected as a buffer slug before waterflooding, recovery of the oil-in-place was 8 to 22 percent greater than with conventional waterflooding in the test specimens, regardless of the con¬tinuous phase (oil or brine). The emulsions do not appear to be applicable to the Appalachian area; however, because the oilfields are too "tight," the clays in the formation remove the emulsifier from the displacing fluid, and not enough additional oil is produced, compared with recovery using conventional waterflooding, to warrant the increased operating costs.

Jan 1, 1969

By Edward J. Karkoska

The film you see is a slow motion view of a typical half million ton taconite blast at one of Erie's mines. This blast is made up of 220 drill holes and a total of 325 thousand pounds of blasting agent. The second view of the same shot is taken by a remote control hi speed camera located 1500' directly in front of the blast. Shortly you will see some violent camera movement as the air blast shock wave strikes the camera location. As the blasting sequence progresses the rock fly becomes evident, and if you will look closely amidst the clouds of smoke, rock fragments weighing up to 1/2 ton begin to cascade into view. These missles are the chief concern of blast security. The next camera shot at 4000 frames/second vividly describes the primacord firing lines detonating the blast. Travelling at 22,000 ft./sec., this white snake of fire travels to each hole, detonating the blasting agent. Before we get into the matter of blast security, let me locate our operation for those of you not acquainted with Minnesota's iron ranges and tell you something about our company.

Jan 1, 1969

A modified liquation technique was developed for recovering tin from tinhouse scruff metal or hardhead containing about 10 per cent iron and 15 per cent occluded flux, palm oil, and moisture. This was effectedby heating the scruff metal to 950°C followed by rapid cooling to suppress the formation of FeSn2 and FeSn, and then subjecting it to the ordinary liquation and drossing processes of refining. By this method it was possible to recover about 83 per cent of the original tin content and, with subsequent smelting of the irony drosses, an overall recovery of 92 per cent was obtained.

Jan 1, 1969

By A. E. Chute

The shortage of sulfur is not only continuing but appears to be worsening, attended by steadily rising prices. At the same time emphasis on air-pollution abatement is also increasing. These two factors, a rising market and the growth of environmental attention, have encouraged producers to carefully review all possible sulfur sources. As a result, production of sulfur from hydrogen sulfide occurring in petroleum is receiving greater attention than ever before. Until about a decade ago, the practice of recovering sulfur from hydrogen sulfide separated from gases (either found naturally or generated in desulfurization of liquid petroleum) was wide1y recognized but contributed little to total free-world sulfur production. However, during the past ten years, the production of sulfur from this source has increased so rapidly that it now accounts for a substantial portion of total production. This trend shows no signs of slackening, and current forecasts predict that recovered sulfur may become the dominant source of supply within ten years, exceeding mined sulfur production. This paper is intended to list sulfur sources and relationships, and to discuss the potential of producing sulfur from petroleum. The processing involved, in addition to product storage and transportation will also be discussed along with important economic aspects of sulfur recovered from hydrogen sulfide. For many years, most of the world's elemental sulfur has been produced from salt domes, predominantly by the Frasch process. During the past decade, however, another production source has developed so quickly that it is expected to surpass the Frasch production sources within a short time. This new source lies in the petroleum gases and liquids from which dramatically increasing quantities of elemental sulfur are being recovered. In the phraseology of the trade, the sulfur so obtained is know as "recovered sulfur," a term which does not, as one might expect, include sulfur recovered from other sources such as smelter gases. The growth rate of recovered sulfur compared to that of Frasch sulfur, total elemental sulfur, and total Free World sulfur in all forms is shown in Fig. 1 Since 1963, sulfur consumption has exceeded production,with the natural result that the price of sulfurhas continually increased. The posted price reported for f.o.b. Port Sulphur, La., has risen from as low as $18 per ton in 1962 to $32.50 per ton in mid-1967. With freight and other charges, delivered prices have of course run much higher, amounting to $45 or $46 per ton on the east and west coasts. In some cases, spot sales for as much as $60 have been reported. Although it is playing an ever-increasing role in the sulfur market, recovered sulfur was originally a by-product of the removal of hydrogen sulfide from natural and petroleum refinery gases. Today, however, it is often the most valuable product of a multi-product processing facility. Since there are two major sources of recovered sulfur—production and refining processes —natural gas is included with liquid petroleum for purposes of this discussion. Sulfur from these sources is produced in the form of gaseous hydrogen sulfide which is removed from a gas stream and converted to elemental sulfur. Gases in which hydrogen sulfide occurs naturally are natural gas and the gas produced from a high=pres-sure crude=oil or condensate field.

Jan 1, 1969

By Albert H. Fay

The gypsum industry makes significant contribution to the wealth of our nation. This non-metallic mineral ranks in the highest order with America's most precious resources. Evidence of this is borne out by the fact that gypsum is a vitally necessary element in the building, industrial and agricultural industries. In 1967, the United States consumed 14 million tons of this valuable ore. Of .this amount 69% was required by the building industry for the manufacture of building materials. An additional 21% was directed to the industrial market, for the manufacture of Portland Cement and for other industrial uses. The remaining 10% was used for agricultural purposes.

Jan 1, 1969

By Joseph P. Nugent

The new combination gypsum plaster and gypsum wallboard plant of Compania Industrial Kaiser S.A., the first of its kind in Mexico went into production in April of 1969. This was approximately fourteen months from the signing of the formal order for the plant and equipment. Compania Industrial Kaiser S.A. is an affiliate of the Kaiser Gypsum Company in the United States and will market practically the same line of products and to the same standards as those produced in American plants. Located in the City of Puebla, the plant will readily service the major Mexican sales areas. It is approximately 85 miles away from Mexico City on a modern, four-lane, divided highway and distribution to other major consumer areas can be readily effected by the use of a good highway system, as well as, by rail. This, plant is the, sixteenth Gypsum Wallboard Mill supplied abroad by my company, United States Wallboard Machinery Company. Other installations are in Australia, New Zealand, Chile, England, Scotland, Ireland, Finland, South Africa, Latvia and Germany. Two new mills are on order; a small unit for Brazil and a comparatively large unit for New Zealand. All these mills have one thing in common with plants in the United States and Canada; they are equipped with standard, time-proven and tested equipment and they are designed in accor¬dance with the latest engineering thinking in order to produce efficiently, the highest quality product at lowest cost. They differ generally in the size of plant, the factors that brought them into being and in the market that they supply. I believe that these differences will be of interest to you.

Jan 1, 1969

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

Jan 1, 1969

By K. R. Dorman

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed a five-piece precast concrete drift set for a small opening and tested it to destruction in a straining frame. Twenty-seven tests were made with three sizes of members using three loading conditions. In addition, six tests were made with sets in a distorted configuration, Test results and typical failure patterns are presented. A comparison of results with those previously reported for the three-piece set shows the five-piece set supports considerably larger total loads than does the three-piece set of equivalent cross section designed for the same size of opening. Recommendations are made for improvements in design.

Jan 1, 1969

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port Kembla steelworks of Australian Iron & Steel Pty. Ltd., vary in rank and in type over the Southern and South Western Coalfields.The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal.Plans of seam variation show the regional trends in rank and type for each seam.The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Seam in a zone embracing Bulli and Appin collieries.A satisfactory correlation is achieved between vitrinite content and coke stability and hardness, enabling prediction of coke strength for Southern Coalfield coals.The use of vitrinite reflectance, as an indicator of rank, in addition to type to predict coke strengths is at present hampered by lack of data, particularly in the South Western Coalfield. Nevertheless, data available at present allow the use of both variables and give better correlations with coke strengths than type alone.A spread of comprehensive data across both coalfields will enable advance assessment of cokes produced from coals having known rank and type. Blending to a ranktype specification for optimum coke strengths would allow the best use of the coal reserves of the coalfields.

Jan 1, 1969

The ultraviolet spectrum of isopropyl ethylthionocarbamate (the principal constituent of Dow flotation collector Z-200) in water and of Z-200 itself in water was found to have an absorption peak at 242 nanometers(nm). The height of this peak was found to be directly proportional to isopropyl ethylthionocarbamate concentrations up to 15 p.p.m. Z-200 contains about 90 per cent isopropyl ethylthionocarbamate and the heightof the peak was proportionately lower, but obeyed the straight line relationship up to 15 p.p.m. This showed the potential value of spectrophotometric measurements for the determination of Z-200 residuals in flotation liquors.Methyl ethyldithiocarbamate (an impurity in Z-200) increased the peak height slightly, but other impurities in Z-200, xanthates, and most inorganic salts present in flotation liquors do not interfere. However nitrate ion and thiosulphate ion have absorption peaks which overlap the isopropyl ethylthionocarbamate peak.The simplest general method to overcome this effect is to extract the isopropyl ethylthionocarbamate into cyclohexane and to measure the absorbance of the extract.The maximum absorbance of the cydohexane extract was at 247 nm and the peak height at this wavelength was found to be directly proportional to the isopropyl ethylthionocarbamate or Z-200 concentration in the original aqueous solution. An alternative method is to measure the spectrum of the original aqueous solution using the aqueous raffinate from extraction as a reference solution. This gives the spectrum due to isopropyl ethylthionocarbamate alone and measurement of the absorbance at 242 nm gives the concentration in the original aqueous solution. Both methods give the same value for the concentration of isopropyl ethylthionocarbamate in the original solution.

Jan 1, 1969

By M. M. Tilman

In a Bureau of Mines investigation to develop lead alloys with improved tensile strength and creep resistance, lead-base alloys containing cadmium and antimony in nominal 1-to-1 atomic ratios were melted in air, cast, and rolled into sheet to 90 percent reduction at temperatures varying from room temperature to 175° C. Tensile testing at room temperature and stress-rupture testing at 900±3° F were conducted on the as-rolled alloys. The best tensile properties were observed in an alloy of Pb-4.2 wt pct Cd-4.5 wt pct Sb which exhibited an average tensile strength of 7,270 psi with 36 percent elongation in 2 inches. An alloy of Pb-5.5 wt pct Cd-6.0 wt pct Sb had 100-hour stress-rupture values of approximately 2,100 psi and 1,000-hour values of approximately 1,700 psi.

Jan 1, 1969

By R. L. Rock

The Bureau of Mines conducted radiation-ventilation studies in six large underground uranium mines to investigate the extent of radon-daughter exposure experienced by the miners and to analyze the ventilation systems to set what changes were required to achieve recommended radiation standards. The studies entailed tracing and measuring the mines' ventilating air, quantitatively and qualitaitively, from its entrance into the mines, through production areas, and lack to the surface. Pressures consumed in creating airflow through mine circuits were determined by altimeter surveys. Air quantities were measured with anemometers or by chemical smoke cloud methods. Air quantities delivered through tubing were determined using U-tube water gages to magnahelic gages to measure velocity pressures. Radon-daughters were filtered from mine air to measure alpha activity; activity levels were converted to "working levels," the established unit for reporting miner exposure. Attention was given to locating unnecessary contamination influx sources and recirculating air. The radiation-ventilation surveys showed that where basic principles of food ventilation were not followed, high alpha radiation levels invariably resulted. Some mines required more primary air for controlling radiation levels throughout active areas, but more efficient use of available air was generally possible. Premature contamination of intake air was prevalent where development Openings intersected ore or passed by worked-out stopes. Several auxiliary systems were inefficient in secondary distribution, recirculating air already too highly contaminated for ventilation. Many got these common problems can be traced try the lack of dine planning with radiation control in mind.

Jan 1, 1969

By Taylor G. H

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopical techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relat- ing their inherent properties to properties such as volatile- matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used coimierciallyti,

Jan 1, 1969

By K. Takahashi, I. Iwasaki

it is well known1 that racemic mixtures of optical isomers can be separated by passing their solutions through a column packed with r- or 1-quartz powder so that one of the isomers becomes adsorbed selectively on the asymmetric quartz surfaces. Although the natural occurrence of r- and 1-quartz is more or less equally distributed, some localities show enough deviations toward a higher proportion of l-quartz2 to suggest that optical isomerism might influence quartz flotation. Beta-amines have an asymmetric carbon atom, and therefore optical activity may be expected. Beta-amines are reported to behave quite differently from alpha-amines in the flotation upgrading of certain oxidized iron ores.3 It is of interest, for both practical and theoretical reasons, to determine whether or not optical isomerism plays a role in the amine flotation of quartz. In this article the results of Hallimond tube flotation tests and of adsorption measurements using d-beta-phenylisopropylamine on both r- and 1-quartz are compared. D-beta-phenylisopropylamine was chosen for the tests because it is commercially available in optical isomers. MATERIALS AND METHODS Brazilian quartz crystals were hand-sorted according to the difference in trigonal trapezohedral faces, and each crystal was further checked by the Airy's spiral.4 The respective crystals were then crushed, and the -150 + 200-mesh fractions were screened out for the Hallimond tube tests. The samples were cleaned by brief leaching with warm, dilute hydrochloric acid, and then by repeated rinsing with distilled water. In preparation for the adsorption measurements, they were then dry-ground in a pebble mill for several hours, washed a few times with distilled water, and finally dried in a vacuum desiccator. By means of the Krypton gas adsorption method, the specific surfaces of r- and 1-quartz samples were determined to be 27,700 and 19,800 sq cm per gm respectively, the difference being due mainly to the decantation procedure rather than to the inherent difference in their grindability. D-beta-phenylisopropylamine was the only collector used in the study. It was solubilized by neutralizing with 110% of the stoichiometric requirement of 0.1 N hydrochloric acid. The specific rotation of the d-beta-phenylisopropylamine was determined with a polari-meter using sodium D line to be, Although the d-beta-phenylis~prop~lamine showed absorption maxima in the wave length region of 250 to 270 millimicrons, due presumably to the phenyl group, these peaks were too sensitive to be used for colorimetric determination of the residual concentration in the adsorption measurements. The amine-picrate method, used in the colorimetric analysis of dodecylammonium chloride,' was found to work satisfactorily for the d-beta-phenylisopropylamine. The adsorption densities were thus determined after equilibrating 40 gm of the ground quartz sample with 300 ml of solution by tumbling in separate glass-stoppered Erlenmeyer flasks for one hour. EXPERIMENTAL RESULTS Fig. 1 presents the adsorption densities of d-beta-phenylisopropylamine on the r- and 1-quarts in the pH range of 6 to 7.5. In agreement with data reported in the literature, the adsorption density of d-beta-phenylisopropylamine was slightly higher on the r-quartz than on the 1-quartz, although the difference was not as pronounced as one might expect from the capacity of r-quartz and 1-quartz to separate racemic

Jan 1, 1969

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969

The lead concentration of flotation feed ore slurries is determined using two ?-ray absorption gauges mounted directly on a 6 in. diameter flotation feed pipeline. One gauge is a conventional "density" gauge using CS137. The other is a "lead-sensitive" gauge, which depends on the preferential absorption. by lead of 225 key y-rays resulting from Compton backscatter of CS137 y-rays.Gauge outputs are combined using an analogue computer the output signal of which is directly proportional to the lead concentration of the pulp. The accuracy of measurement of the pulp lead concentration is ± 3·6 per cent for ore slurries with lead concentrations in the range 0'07-0·16 g/c.c. and pulp densities 1.43-1.60 g/c.c.This paper sets out the development of the technique and details are given of the two experiments (1964, 1966) conducted in the plant at North Broken Hill Limited. The installation of the two-gauge system inthe plant during May 1968 is described. Details are given of the calibration technique used and the results obtained.

Jan 1, 1969