Search Documents

By George J. Conroy

Electrical power generation was studied in a laboratory-scale, open-cycle vortex MHD generator, which offers several advantages over straight-channel generators that require separate combustors. Compactness, lower capital cost, and high-energy release are obtained by combining the combustor and generator into one unit in the vortex generator. In addition, the vortex generator uses a simple solenoid rather than the more complex and expensive saddle magnet required for straight channel generators. Although the vortex generator must utilize combustion gases with a low Hall coefficient in order to be efficient in direct comparison to the linear generator, the primary motivation for this experimental device in terms of ultimate objective was to investigate the vortex generator with applications to direct coal firing and with combustion taking place in specially designed expansion nozzles. The vortex device offers one decided advantage over the linear device in this regard because slag deposits do not degrade or short-circuit the coaxial electrodes as is the case for a linear machine. The experimental vortex generator consists of a modified cyclone burner 7 ½ in ID by 21 in long, with the inner wall used as one electrode together with a coaxial center electrode. Power was obtained by impressing an axial field of 3,000 G from an air core solenoid magnet. Tests were conducted by seeding natural gas seeded with potassium acetate and burning with preheated oxygen-enriched air. Power generation was lower than calculated because theoretical plasma velocities were not achieved.

Jan 1, 1972

By Robert B. Worthington

This investigation was undertaken to develop a more efficient copper smelting practice that would help meet the increasingly stringent antipollution standards. Continuous smelting to copper and a 0.8-to 5-percent copper slag using pure oxygen has been demonstrated for several hours at a time in a unique double furnace, which was devised to overcome the heat losses inherent in a laboratory furnace. The use of pure oxygen to effect the smelting and conversion of copper sulfide concentrate in a single unit to produce blister copper and a very high S02 concentration provides a much reduced gas volume for more economical and thorough sulfur recovery. Although the process was successfully demonstrated for several hours at a time, extended test work using longer runs will be required to balance the system and to obtain test data for adequately demonstrating its technical feasibility.

Jan 1, 1973

By Robert C. Steckley

A study of joints in Marathon County, Wis., was made to determine the orientation of regional paleotectonic stresses and to develop a method of using optical diffraction analysis (ODA) in studying joint orientations and spacings. Standard geologic and petrofabric techniques employing the use of a geologic compass and a Schmidt net were used in gathering, describing, and reducing joint orientation data. Analysis of selected outcrops with ODA indicates that ODA can be applied to study both joint orientations and spacings. ODA is shown to be a rapid method that can be used to complement standard petrofabric techniques, especially in the study of joint spacings.

Jan 1, 1972

By Alan H. Goode

Glass wool meeting requirements for commercial use was made from glassy fractions of urban solid wastes by the Bureau of Mines. This research was a part of the Bureau's program to develop building products and other usable materials from reclaimed urban waste materials. Mixes of molten glass were fiberized into glass wool during laboratory studies by impingement of a jet of compressed air on a stream of the molten glass. The principal test variable studied was composition of the melt; this was varied by adding dolomite and alumina to obtain molten glass with the handling characteristics required for producing final wool products of the desired composition and physical characteristics. When no charge is made for the waste glass and approximately $75 per ton can be obtained for the wool product, an interest rate of return on investment after taxes of about 12 percent can be obtained. If a charge of $5 per ton is required for the waste glass, a selling price of about $78 per ton would be necessary to obtain a l2-percent-interest rate of return on investment after taxes.

Jan 1, 1972

By George A. Savanick

The objective of this research is to develop a method for measuring the tensile strength at the interface between minerals in rock. These measurements reflect the strength of the attractive forces operating at crystalline interfaces in rock. Since these forces act in opposition to the forces set up in various rock fragmentation processes, measuring their strength may help in designing more efficient methods of rock fragmentation. The method developed for measuring the strength of intergranular adhesion in rock involves separating a bicrystal from the rock and determining the tensile strength at its solid-solid interface. This technique has been successfully applied to the study of quartz-feldspar interfaces separated from massive pegmatites, graphic granite, and the Rockville granite, yielding average tensile strengths of 5.86, 8.62, and 10.65 meganewtons per meter squared (MN/m2) (850, 1,250, and 1,524 psi, respectively). The data this technique provides indicate that the members of these bicrystals are strongly adherent. Examirtation of bicrystals broken at the crystalline interfaces indicates that the bonds responsible for this adhesion operate over only a portion of the interfacial area. This work conclusively demonstrates that tensile strength tests can be conducted on small selected areas; for example, grain boundaries in rock. The small-scale zones of strength or weakness determined in this way can be related to the overall strength of the rock.

Jan 1, 1972

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

By O. Q. Leone

A processing unit was developed for the complete cleaning of titanium alloy chips. The process uses solvent degreasing, magnetic separation, and anodic solution of nonmagnetic impurities in 10 weight-percent sulfuric acid. Vacuum arc-melted ingots weighing approximately 10 pounds each were prepared from cleaning chips according to ingot specifications.

Jan 1, 1973

By R. Blickensderfer

The sparking and gas-igniting tendency of steels and alloys were evaluated my measuring the radiance of spark showers produced by grinding a sample on an abrasive wheel in air, the time required for a spark shower generated on an abrasive wheel to produce an ignition in an explosive gas mixture, and the energy and speed required for impacts between various materials to ignite an explosive gas mixture. Mixtures of air-methane were found quite resistant to ignition by showers of sparks. A mixture of air-9.S pct hydrogen was used to increase the sensitivity of the tests and to thereby extend the range of materials that could be evaluated. The results of the spark-shower tests indicate that carbon steels and the alloy steels found in coal-cutter tools are among the most sparking and most incendive of any materials tested. Stainless steels, nickel alloys, and tungsten carbide are among the least sparking and least incendive. The brightness of the spark showers depended upon the degree of oxidation of the abraded particles. Impact tests against hard rocks such as solid quartz and sandstone, showed that high-carbon steel was more inc endive in the hydrogen mixture than were the softer steels or the alloy steels found in coal cutters. Ignitions were found much less likely to occur at speeds somewhat lower than the speeds currently in use in continuous mining machines.

Jan 1, 1972

By E. G. Valdez

Three cryogenic systems that utilized liquid nitrogen, dry ice, and methanol with dry ice were investigated in conjunction with crushing and classifying techniques. The systems were used to aid in separating and reclaiming the metallic components contained in insulated wires, shredded automobile nonferrous metal concentrates, small motors, generators, and rubber tires. Wire strands, 2 to 6 inches long and insulated with polyvinyl chloride and neoprene, were chilled at -60° and -195° C, then roll-crushed and processed by water elutriation; this procedure resulted in two products--a sink fraction that was 99 percent metallic and a float fraction that was 99 percent nonmetallic. Excellent separation of zinc die-casting alloys from copper and aluminum contained in shredded automobile nonferrous metal concentrates was attained by chilling at -72° C for 1 minute, crushing in a grateless hammer mill, and screening. From the screened products, 97.2 and 100 percent of the copper and aluminum, respectively, were recovered in the plus Pinch fraction, and 100 percent of the zinc was recovered in the minus 1-inch fraction of over 97 percent zinc die-cast purity. Laboratory experimental results comparing direct and indirect chilling indicated that a sufficiently low temperature could be attained by indirect chilling to permit use of a liquid C02-dry ice system on insulated wires and mixed nonferrous metallic concentrates.

Jan 1, 1973

By K. J. Liles

The Bureau of Mines conducted laboratory semicontinuous and continuous heavy liquid tests to determine the feasibility of producing commercial-grade products from the high-clay sylvinite ores of the Permian Basin in New Mexico. Continuous test operations demonstrated that concentrates containing 59.9 percent K2O and recoveries of over 75 percent of the contained potash can be obtained. The organic heavy liquid was effectively recovered by vaporization, condensation, and absorption methods. Less than 5 parts per million of heavy liquid vapors were released to the atmosphere. This loss represents only 0.02 pound of heavy liquid per ton of ore treated.

Jan 1, 1973

By G. A. Wancheck

Shear tests were performed on several prepared samples of granular and powdery bulk materials to investigate the following parameters: Particle size and distribution, particle movement, moisture content, consolidation of material, bulk density, void ratio, porosity, volume change, and strain rate. A series of shear tests was performed with weight-percent-ratios of minus 0.185-inch tertiary sand and 1-1/2-by l/2-inch tertiary gravel mixtures, and weight-percent-ratios of minus 200-mesh limestone (rock dust) and minus 200-mesh bituminous float coal dust. A comparison was made for shear test results obtained with rectangular and circular shear cells utilizing the large and small direct shear testers. Specifically, the shear results obtained include the angle of internal friction or shear strength of the tested material under known consolidating pressures, and the kinematic angle of friction or coefficient of friction between the interface of a bulk material and a sample wall material. The experimental procedure, tests, and results are given for each parameter investigated.

Jan 1, 1973

By J. R. McVey

A 10-channel automatic data acquisition system has been designed and environmentally packaged for use with underground strain-gage applications and associated instruments. The system uses commercially available components and is assembled in two plastic enclosures. Environmental control is provided through a specially designed (compressed-air) air-conditioning system and water-resistant cabling. Accuracies of 0.01 pct and resolution of 1 µV have been obtained in underground tests.

Jan 1, 1973

By L. K. Barker

The purpose of this research was to determine how much, if any, improvement would be made by subjecting hydrogenated shale-oil naphtha to a catalytic reforming process. Preselected ranges of temperature and pressure within the commercial reforming ranges were chosen for investigation and other possible variables were held constant. All tests were made with a liquid hourly space velocity (LHSV) of 3 volumes of liquid feed per volume of catalyst per hour (Vf/Vc/hr) and a hydrogen feed rate of 3,000 scf/bbl. Operating temperatures of 850°,875°, and 900° F were used at pressures of 200,400, and 600 psig. The greatest octane improvement in the naphtha was obtained at a temperature of 900° F and pressure of 200 psig. The reformed naphtha had a clear research octane number of 89, a liquid yield of 80 vol pct, and a yield-octane number of 71.1. The data indicate that a higher temperature could have produced a higher yield-octane number.

Jan 1, 1973

By F. E. Joyce

This paper describes the development of a process for producing manganese and iron pellet concentrates from low-grade manganiferous iron ores of the Cuyuna range by a two-stage sulfatization-reduction roast. First, the manganese minerals (7.5 percent manganese) were converted to water-soluble manganese sulfate by roasting in sulfur oxide gases at 700° C, then, the hematitic iron minerals (31 percent iron) in the hot sulfatized are were reduced to magnetite with simulated reformed natural gas in the temperature range of 350° to 425° C. Batch tests were made in a 3-inch-ID by 6-inch-long, gas-heated, stainless steel retort, and continuous countercurrent experiments were performed in a 2-inch-ID by 10-foot-long, electrically heated shaft furnace. Manganese sulfate was removed from the roasted product by leaching with water, and over 90 percent of the manganese was recovered in an oxide product (65 percent manganese) obtained by precipitation, drying, and thelmal decomposition of the sulfate. An iron oxide concentrate (60 percent iron) with an iron recovery of 75 percent was obtained from the water-insoluble residue by magnetic separation.

Jan 1, 1973

By D. S. Burgess

This report summarizes the incidents that preceded the December 9, 1970, propane-air explosion in Port Hudson, Mo., and then attempts to establish the nature of the explosion from the ensuing events. Special emphasis is given to possible ignition sources, the distribution of flammable vapors, and the analysis of blast damage. Both near-and far-field damage indicated that this explosion may be attributed to the detonation of propane in air with an energy release equivalent to that from about 50 tons of detonating TNT.

Jan 1, 1973

By Walter W. Fisher

A study of copper cementation on iron was initiated to determine the effect that deposited copper has upon subsequent cementation. A microscopic investigation of cementation on an iron surface showed that cupric ion precipitates predominately on a growing copper deposit attached to the iron surface. A kinetic study of the cementation process in a revolving drum showed that the cementation rate is enhanced by the copper deposit attached to the iron surface and by the discrete copper particles of a cement copper slurry. The kinetic study also indicated that the character of the deposit is affected by the major anion in the solution. The cementation process is visualized to occur as a series of electrochemical cells in which cupric ion precipitates on copper dendrites attached to the iron surface.

Jan 1, 1973

By A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which bid no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton A coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

By J. B. Rosenbaum

Prolonged laboratory and limited pilot plant tests have shown that the Bureau of Mines buffered S02 -H2S process is capable of removing 95 to 99 percent of the S02 from industrial waste gases. Most of the S02 is converted to elemental sulfur; only about I percent converted to sulfate The process comprises (1) washing the flue gas to remove particulates and S03, (2) absorption of the S02 in citric acid or other carboxylate solution, (3) reaction of the loaded solution with H2S in a closed vessel to precipitate the absorbed S02 as elemental sulfur, and (4) separation of the sulfur from the regenerated solution by oil flotation and melting. Two-thirds of the molten sulfur is converted to H2S for use in the sulfur precipitation step by reacting sulfur vapor with natural gas and steam in the presence of an alumina catalyst. The chemistry and mechanism of the process are described, initial laboratory and pilot plant data are summarized, and second-generation laboratory operation and pilot plant design are reviewed. Preliminary cost estimates are presented for recovering sulfur from copper smelter gas, powerplant flue gas, and Claus plant tail gas.

Jan 1, 1973

By Mark I. Copeland

The Bureau of Mines investigated the effect of up to 1 wt-pct of copper and silicon on the heat treatment response and hardness, tensile, and impact properties of hot-rolled medium-carbon steels. The steels were prepared by induction melting and fabricated into plates by forging and rolling. The tensile strength of 0.2-wt-pct carbon steels containing 0.3 wt-pct silicon was affected significantly by copper in both the hot-rolled and heat-treated (600° C) conditions, whereas the tensile strength of the 0.3-wt-pct carbon steels was less affected. A 600° C treatment was considered optimum as a post-rolling treatment to strengthen the steels by copper precipitation. Strengthening of 0.2-wt-pct carbon steels by silicon was reduced by increasing copper contents.. Optimum impact strengths occurred at about 0.3 wt-pct silicon in 0.2-wt-pct carbon steels containing 0.6 and 0.8 wt-pct copper. The impact strengths were lowest for 0.2-wt-pct carbon steels containing over 0.8 wt-pct copper and greater than 0.3 wt-pct silicon, especially in the heat-treated condition. Copper and silicon solutes and copper precipitates strengthened the steels. This effect was augmented slightly by strengthening through grain refinement by these solutes.

Jan 1, 1973

By M. Hertzberg

Results of a comprehensive study of the absolute spectral radiance of the infrared emissions from methane-air explosions are reported. The spectral growth of these expanding flames were recorded with a time resolution of 1 msec in the spectral range of 1.7 to 5.0 µm. Time-resolved spectra were obtained for methane-air mixtures as a function of stoichiometry, nitrogen dilution, and Halon dilution, in a 9-liter vessel under different venting conditions. Data are also presented for coal dust-air explosions. Temperatures, obtained from the absolute radiances and from a band ratio technique for methane-air, are internally consistent and are generally 50° to 200°K below adiabatic flame temperatures. All near limit mixtures gave essentially the same flame temperatures (1,500° to 1,600° K) regardless of whether the limit was obtained by dilution with excess air, excess methane, excess nitrogen, or Halon. The coal dust explosion spectrum is essentially a blackbody continuum at 1,500° K with some selective emission at 4.4 µm from hotter CO2. The data are analyzed in terms of the radiative dynamics of a sperically expanding flame zone. The importance of radiative transport is assessed. An equation is derived which relates the instantaneous fraction of combustion power radiated to adiabatic variables.

Jan 1, 1973