Search Documents

By M. E. Wadsworth, T. D. Chatwin

The kinetics of sulfidization of hematite (Fe203) by H2S gas at various partial pressures have been determined over the temperature range of 170° to 500°C. The process was controlled by thin films of pyrite (FeS2) and troilite (FeS) which were protective and formed diffusional layers. At higher temperatures the thermodynamic drive to form FeS2 decreased, and consequently the rate of formation of FeS, decreased. Conditions for the development of thin layers of FeSz consisting of 10 to 100 atomic diameters are presented. Laboratory flotation results on synethetic ores indicate floatability identical to that of pyrite of normal xanthate flotation. The prospect of high-temperature sulfidization of metal oxides using H2S, S, or other sulfur bearing compounds is intriguing as a potential activation process for flotation since the thermodynamics are very favorable for a large number of systems. If the kinetic parameters are sufficiently well understood it may be possible to provide surface sulfide layers a few angstroms thick, thus imparting normal sulfide floatability characteristics to the oxide. For thin layers the total sulfur pick-up would be small except for very high surface area materials but in most cases this sulfur could be readily removed by roasting if necessary. The general reactions for the sul-fidization of metal oxide MxO, to a metal sulfide MpSq using H2S may be written for the three conditions py > xq; py < xq; and py = xq: A large thermodynamic advantage is obtained in many systems because of the relatively large negative free energy of formation of H,O compared to H,S. For the temperature range 2S° to 1500°C &apos; where AFOis the standard free energy and T is absolute temperature. As is evident from Eqs. 4 and 5, the free energy of formation of H ,0 is approximately 35 to 37 kilocalories per mole greater than that for H,S over broad variations of temperature. For oxide-sulfide systems as outlined above, sulfidization may be expected to occur for the conditions: Groups I and 111: that is, if the terms on the right are more negative than those on the left the reaction is expected to occur thermodynamically. The value hFg,(,) is included in Eq. 6 since hFLzs is based upon gaseous S2 rather than the normal reference state, orthorhombic sulfur. The

Jan 1, 1969

By J. F. Shea, O. F. Tangel

Battelle Memorial Institute participated in a program for the General Services Administration aimed at developing a nickel-cobalt separation process that could be integrated in the Nicaro nickel plant. At the time the programwas being carried out, the Nicaro process was a straight-through operation, in which the ore was reduced and leached, after which the pregnant solution was boiled to produce a so-called "bulk precipitate" which contained virtually all of the nickel and cobalt which had been dissolved in the leaching step. The weight ratio of nickel to cobalt in Nicaro ore is approximately 15 to 20:l. The weight ratio of nickel to cobalt in the finished product had to be 100:l or higher to meet specifications. Because the Nicaro process embodied no nickel-cobalt separation step, the only way that a bulk precipitate of the specified nicke1:cobalt ratio could be produced was to so adjust roasting and leaching conditions that nickel would be selectively leached and most of the cobalt would be rejected with the tailings. The required selectivity, however, was achieved at the expense of nickel recovery, which was 5 or more per cent less than might have been obtained with the existing equipment, utilities, man power, etc., had selectivity been no object. The over-all purpose of the program was to develop a separation step that could be fitted into or onto the Nicaro facilities and which would permit the manufacture of a product that would meet the desired specifications and still permit the recovery of a maximum amount of nickel. Battelle suggested that this might be accomplished by reprocessing off-specification bulk precipitate and specifically suggested the process based on ammonium sulphate leaching followed by hydrogen reduction of the leach solution according to techniques developed commercially by Sherritt Gordon Mines Limited. Such a process would not only satisfy the objectives of the research but would present two additional advantages. (1) It would produce a separate cobalt product which could be further processed into metal, alloys, oxides, or salts. (2) It would yield nickel in metallic form which might be more generally marketable and command a slightly higher price per unit of nickel than the Nicaro oxide product. DESCRIPTION OF THE PROCESS Figure 1 is a flowsheet of the process. The essential features are: (1) Extraction of about 97 per cent of the nickel and about 85 per cent of the cobalt from bulk precipitate by a principal leach with ainmonium sulphate solution (Step A). Extraction of virtually all of

Jan 1, 1961

By J. E. Forciea, O. E. Palasvirta, L. G. Hendrickson

AH pilot and commercial plants working with Mesabi Range taconite employ wet magnetic separation. Progress is being made with a dry magnetic process, but this has not yet been applied to taconite except in the laboratory and pilot plants. Flowsheets in all five plants are similar, including multiple stages of grinding, each followed by magnetic separation, which rejects a finished tailing. The flowsheet in Fig. 1 is used in the preliminary and commercial plants of the Erie and Reserve mining companies and in Unit C of Oliver&apos;s Pilotac plant. At Erie the desliming operation is omitted. In the Reserve plants two ball mills are used with each rod mill. Pilotac uses flowsheet 2 in Unit A-B and has also tested flowsheet 3. Principal differences in the three flowsheets are the number of grinding stages and the type of roughing. The terms open-circuit roughing and closed-circuit roughing are best defined by the diagrams. Special Test Data Given in Table I: For the Erie and Reserve commercial plants, Table I reflects routine conditions. Pilotac, the experimental plant, has been run with several flowsheets, including those followed at Erie and Reserve&apos;s commercial operations. Pilotac data for these last two flowsheets are similar to commercial plant results and are not repeated in Table I; statistics are given, however, for special test conditions. using other flowsheets. when the objective was to &apos;to extra-grade concentrate, Variations Among Taconites: Although crude ore tributary to these plants is generally classified as taconite, there are important differences in mineralogy and fineness of dissemination.

Jan 1, 1959

By A. M. Gaudin, J. H. Brown

In a survey of the effects of heat treatment on the comminution of various rocks, it was found that unusual size distributions often characterize the broken products, and that this is related to a great increase in intergranular fracture1. It is the purpose of the present paper to contribute to an understanding of this effect. In a thesis by one of use, critical consideration was given to many mechanisms which could conceivably be responsible for the increased intergran-ular fracture. It was shown that neither gross chemical changes nor intergranular corrosion are required. Among non-chemical mechanisms the most likely appeared to be (1) Uneven expansion due to thermal gradients, giving spalling (2) In a manner similar to that prevailing in metals, the appearance at high temperature of intergranular weakness. (3) Unequal thermal expansion of adjacent grains. Experiments were designed and conducted to permit a choice among the many alternative mechanisms and in particular among the three listed here. EXPERIMENTAL MATERIALS Tests were made on the materials listed in Table 1. Of each material, only lumps similar in composition and grain size were used. The three marbles listed in Table 1 were analyzed to assure that their chemical compositions did not differ greatly (Table 2). On the basis of the chemical analyses, of differential thermal analyses, and of X-ray powder diffraction patterns, it appeared that the marbles were very similar except for their grain sizes.

Jan 1, 1961

By H. E. Lee, D. Ingvoldstad

AT Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were provided by an ample supply of siderite middlings and coarse lime-rock. While oversize material was crushed through %-in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity. Prior to 1938 the relative proportions of zinc receipts were low and extraneous flux requirements at a minimum. However, subsequent war-inflated zinc demands brought marked increase in fine concentrate and slimy zinc leach residue receipts and an abrupt introduction to smelting a more refractory zinciferous charge. The higher temperature demands of the more refractory zinciferous charge required a higher smelting column and the higher column, in turn, rendered the blast furnace less receptive to improperly prepared feed. Inadequate presinter processing facilities prevented the production of acceptable sinter, and blast furnace production declined to 50 pct of former capacity. In view of a prevailing contention among lead metallurgists as to the deleterious action of high zinc slag on blast furnace capacity, it was natural to overstress this factor and to concentrate on possible changes in furnace design. Another interpretation was that primary correction should be sought through expanded sintering facilities. This divergence of opinion, together with the extreme material shortages of the 1940&apos;s, delayed corrective

Jan 1, 1957

By A. Alonso, J. Daubenspeck

In the nickel extraction process at Nicaro, Cuba, dried and ground nickel bearing laterites are reduced at 1300-1400F in multiple-hearth furnaces. Nickel is leached from the reduced ore by aeration in an aqueous solution of ammonium carbonate. Nickel carbonate is precipitated from the liquor and calcined to yield nickel oxide. The following are the more important modifications of the Nicaro process since plant rehabilitation and expansion. Ten percent increase in tonnage was achieved without decreasing the fineness of the ore by minor mechanical modifications of the grinding plant. Another five percent increase in tonnage was attained by intentionally overloading the ore prepration and leaching circuits in an effort to control cobalt extraction. Modifications at the sintering plant allowed it to handle the entire output of the expanded plant. A fifty percent increase in leach liquor cooling facilities alone provided an increase in nickel production of five percent. Stronger fresh leach liquor for increased nickel washing efficiency was obtained through improved distribution of water to the ammonia absorption towers. Advantage was taken of the reduced calcine&apos;s capability to precipitate cobalt, and modifications in the leach liquor circulation provided controlled cobalt solubility with minimum harm to nickel extraction. Several process changes at the drying plant brought about a ten percent reduction in the fuel oil consumption at this pint. Controlled air addition to the reduction furnaces&apos; upper hearths burned formerly wasted combustibles thereby reducing oil consumption by twenty percent. The nickel extraction process successfully emplayed on the extensive but lowgrade lateritic ores of Eastern Cuba at the U. S. Government owned Nicaro plant, has been previously described in various publications. The large mine and plant operated by the Nickel Processing Corporation, located on the northeastern shore of Oriente Province, have been recently expanded to a yearly capacity of about 50 million pounds of nickel. Essentially, the operation involves open pit mining of a limonite-serpentine ore mixture containing 1.3 to 1.4 percent nickel and 34 to 38 percent iron. The comparatively lumpy, wet (25 to 30 percent moisture) ore is first dried and ground prior to chemical treatment, to which the entire 7,000 tons per day feed must be subjected. In the initial chemical action the dried and ground ore is reduced with carbon manoxide and hydrogen at 1300-1400° in multiple-hearth furnaces. The resulting metallic nickel is selectively leached from the reduced calcine by aeration in an

Jan 1, 1961

By S. A. Falconer

The benefication of non-sulfide or non-metallic minerals by froth flotation has been practiced commercially for at least 30 years. In the pioneer stages of development of this flotation art, most of the promoters investigated were fatty acids or soaps that had been found to float sulfide minerals. When commercial application of froth flotation started to assume importance in the late 1920&apos; s and 1930&apos;s, a great deal of fundamental research work was done in the laboratory (11-14, 19, 22, 23, 26, 29, 32). Among other subjects, this work included studies of the relative effectiveness of the different fatty acids and their salts on the flotability of various non-sulfide and non-metallic minerals. The successful present-day use of fatty acid and petroleum sulfonate type promoters results from better understanding of the principles of non-sulfide flotation plus the developnent of effective selectivity modifying agents. Many investigators have contributed to a greater appreciation of the numerous interrelated factors involved in fatty acid and soap flotation of non-sulfide minerals. Of these, mention should be made of recent fundamental studies by Tagart and Arbiter (31); Wolstenholme and Schulman (35); Schulman and Smith (28); Wark and his co-workers(3,4) Du FIietz(l5); and J. Leja(24). According to J. Rogers, K. L. Sutherland and E. E. and I. W. Wark(27), "the basic requirements for a &apos;collector&apos; in flotation are that it shall form a film over the surface of the mineral to be floated and that this film should be oriented so that hydrocarbon (non-polar) groups form the effective surface." When modified in that way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince (33)that such a film can be produced only if the collector compound contains an active (polar) group to be attracted to the mineral surface, as well as the non-polar group. The commonly used anionic-type promoters for non-sulfide, non-metallic and metallic oxide ores include: 1. Fatty acids, and their soaps and emulsions. 2. Fatty acids residues — "pitches" and "foots." 3. Sulfonated and sulfated fatty acids and so-called "petroleum sulfonates." 4. Paraffin chain salts — sulfonated and sulfated higher alcohols. 5. Cyclic organic acids or salts, such as naph-thenic acid and naphthenates. Certain fatty acids are more effective than others as promoters for particular minerals under certain specified conditions. Some of the more costly fatty acids or collectors of the paraffin chain salt type may give improved selectivity in some instances and are being used commercially in a limited number of operations. Local availability may dictate the choice of the fatty acid used — for example, the use of palmoil fatty acid for flotation of copper carbonate ores in the Belgian Congo. Coconut oil fatty acids have also found limited use.

Jan 1, 1961

By R. B. Booth, W. F. Linke

The continuous interest of the American Cyanamid Company in producing superior polymeric flocculants and dispersants for the mining industry has resulted in a broad, general study of the physical chemistry of mineral-polymer systems. The aim of this program has been to establish a sound theoretical basis on which practical problems could be analyzed, and which would lead to the development of new and improved flocculating and dispersing agents. This study has required the cooperative effort of physical, analytical, and polymer chemists, as well as engineers familiar with mining problems. This report summarizes the results of some of our investigations over the past two years. Further studies along these and other lines are in progress and will be reported in the near future. MEASURING FLOCCULATION IN THE LABORATORY The foremost problem in studying flocculation in the laboratory has been to establish reproducible methods of comparing and evaluating the effectiveness of various reagents. Previous workers have measured settling -rates 1,8 filtration rates2 , and sediment volumes3 . Direct observations of the floc size, or the clarity of the supernatant liquid, can also be used. AIthough these parameters are all interrelated, they do not always measure the same physical properties of the suspensions, and hence are not equally useful or reliable. Whatever the method of comparison selected. the testing procedure must be carefully defined and standardized. The results must be satisfactorily reproducible, and for practical purposes must accurately reflect the results obtained in mill use. In order to compare the data obtained in these various types of test, the physical nature of the flocculated system must be examined in some detail. In an unflocculated system, only the larger or denser particles (the "sands") settle at a useful rate. The sediment can be observed to build up from the bottom of the cylinder, while the fines remain in suspension for a long period of time. If the system is not disturbed, even the microscopic fines can be seen to classify themselves as they fall over a period of days. When a high molecular weight polymer is added to the system, the colloidal particles are tied together randomly in flocs, and the sands and fines settle together. The line of demarkation between solid and liquid phases moves downward from the top of the cylinder. The settling rate of the flocs depends on their size and on their effective density. For a given mineral sample, the larger the flocs, the faster the settling. Since the large flocs cannot pack as closely as small ones, they produce a sediment with more pore spaces, and hence of larger volume, which is easier to pump and to agitate. Although it is nearly impossible to measure individual floc sizes, it is relatively easy to determine settling rates and sediment volumes. Of these two, the settling rate is simpIer to measure, and hence generally more practical. Reproducible sediment volumes can only be obtained by allowing the solids to pack for a rather long period of time (e.g., hours to days), and although the volumes thus observed are directly related to the degree of flocculation (average floc size), it is often impractical to wait so long for the results.

Jan 1, 1961

By P. Somasundaran, D. W. Fuerstenau

This article presents the results of an analysis of grinding of 1:1 mixtures of 4x8-mesh quartz and limestone in laboratory ball and rod mills. From these experiments, the amount of energy consumed in grinding each component of the mixture was determined. In the ball mill, limestone consumes slightly more energy than quartz in the initial stages of grinding, but as the grinding proceeds quartz begins to consume a slightly greater fraction of the energy. The postulate that the fraction of energy consumed by any material in a ball mill is proportional to its volume fraction has been shown to be approximately true. On the other hand, in a rod mill energy consumption by quartz and limestone is equal only in the initial stages of grinding, with energy consumption by quartz greatly exceeding that by limestone as rod milling proceeds. Preferential energy consumption in tumbling mills has been discussed in a number of papers. For example, from an analysis of the kinetics of comminu- tion in ball mills, Arbiter and Bhrany&apos; obtained rate equations based on the postulate that only coarse particles are ground, indicating that fine particles are protected from the action of the balls by coarser particles. In rod mills this protective action is much more pronounced than in ball mills. Recent studies on the rod milling of limestone-quartz mixtures have shown that this protective action causes the mineral with the lowest grindability (quartz in this instance) to consume the greater fraction of energy. 2 However, in the ball milling of mixtures it has been postulated that the consumption of energy by one of the constituents is determined by its volume fraction within the mill. 3 Possibly this hypothesis may be a simplification of the ball milling of mixtures since the protective action suggested by Arbiter and Bhrany may result in some preferential energy consumption by one of the constituents of a mixture. The objective of this study has been to determine preferential energy consumption in laboratory ball and rod mills by analyzing size distributions of each material in the products obtained from grinding 1:l mixtures of quartz and limestone. MATERIALS AND METHOD The procedure for carrying out the tests on wet grinding quartz-limestone mixtures has already been described.&apos;r3 In the present investigation, 1:l mix-

Jan 1, 1963

By Robert M. Funk, James E. Lawver

The development of a laboratory and pilot-scale high-tension electrostatic flowsheet for the production of iron-ore super concentrates having silica contents in the range of 0.1% is presented, A variety of hematite and magnetite ores were tested with this flowsheet, and the pertinent metallurgical data are given. The applications and limitations of this process are brought out in terms of both practical and theoretical considerations. There have been many new developments in the past few years that have required mineral beneficiation engineers to consider new techniques for iron-ore concentration. Developments in iron powder metallurgy, and particularly the making of sheet metal directly from high-purity iron-ore concentrates, and the concept of using metallized pellets as a substitute for scrap in electric-furnace steelmaking have created demands for what is commonly referred to as iron-ore superconcen-trates. In most cases, specifications for superconcentrates are that they contain less than 0.1% total gangue, with some applications requiring less than 0.05% gangue. To produce these concentrates, new and modified processes are being developed, and the three methods receiving attention as the primary concentrating methods are: 1) Magnetic separation in which dry rotor-type equipment is used for magnetite and the high-intensity magnets are used for hematite. 2) Amine flotation. 3) "High-tension" electrostatic separation (or, elec-trodynamic concentration). This paper examines the high-tension electrostatic process in terms of its limitations and abilities for the production of iron-ore superconcentrates. A technically effective and simple flowsheet was developed through laboratory and 5 and 100-ton pilot-plant studies for the production of concentrates containing from 0.02 to 0.20% SiO, with iron recoveries between 85 and 90%. The process is also shown to be economically feasible. Laboratory Test Program Separation Characteristics: The suitability of the electrostatic high-tension method for iron-ore supercon-centration stems from the fundamental mechanism governing the process, i.e., particles are separated on the basis of differences in electrical conductivities. This conductivity is a characteristic property of minerals, and if the difference between the conductivities of two min- erals is great enough, then their separation can be performed by a high-tension machine. As shown in Figs. 1 and 2, the critical factor is the time necessary for the particle charge density, which is established by a corona discharge field, to decay to a level such that the centrifugal force acting on the particle exceeds its electrostatic, or image, force. At this point, the particle can leave the rotor at some trajectory and fall into an appropriate product receptacle. This decay time is directly proportional to electrical conductivity, and the process variables, such as feed rate, rotor speed, electrode configuration, and rotor composition, are selected to optimize the ability of the separator to resolve different conductivities. Table 1 lists the measured conductivities for some of the iron and gangue minerals used in developing the flowsheet. These results were obtained by using the conductivity cell described by Lawver and Wright.&apos; The discharge curve of most minerals that lend themselves to super concentration by high-tension is so fast that the

Jan 1, 1971

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.&apos;s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC&apos;S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

By K. E. Merklin, F. D. DeVaney

Students of the modern blast furnace seem unanimously agreed that they are observing a major revolution in practice. Rather than changing construction and operation of the furnaces, most of the great advances now under way deal with the raw materials feed. Prepared burdens have gained increasing significance during recent years. Sizing, concentration, and agglomeration have all become bywords to greater production and reduced operating costs. The remarkable results with test furnaces in which self-fluxing sinter makes up part or all of the ore charge foretell even greater improvements. Other investigators have reported many of these advances, and it is enough to predict here that more and more operators will turn to the use of self-fluxing sinter. This change in the operator&apos;s requirements comes at a time when one major section of the iron ore regions, the Mesabi, is finding it difficult to maintain, let alone improve, the tonnage and grade of its shipping product. To meet the new demands with respect to quality and structure, the iron ore producers of this area turned first to screening, crushing, and concentrating intermediate ores. More recently, declining higher-grade reserves have led to multimillion-dollar investments in plants to treat the low-grade magnetic taconites.1,2 To yield a suitable concentrate, the Minnesota magnetic taconites must be ground to about 80 pct through 325 mesh, too fine to be charged directly to the blast furnace or to make acceptable feed to the sinter strand. The pelletizing process was developed to meet the structure requirements laid down by the blast furnace operators. Taconite producers are succeeding in their efforts just when the attention of the blast furnace man is being drawn to the great advantages of self-fluxing sinter.3 The taconite operators are ready with an alternative. Why not produce sclf-flus ing pellets? At the Hibbing laboratory of Pickands Mather & Co., where much of the early work was done that led to Erie Mining&apos;s 7.5-million ton taconite plant at Hoyt Lakes, Minn., preliminary investigations have been made. Present Taconite Operations: Details of this work will be clarified by a brief review of agglomeration practice in commercial taconite plants. After the taconite has been ground to about 80 pct through 325 mesh to liberate the magnetite grains, the ore is concentrated on magnetic separators, thickened, and filtered to about 10 pct moisture. This structure and moisture fit in closely with the conditions required to produce good balls. It has been found with taconite concentrates that at least 60 pct of the feed to the balling drum must be —325 mesh to obtain good ball compaction within reasonable time. The filter cake moisture usually permits a slight water addition at the balling drum, and further balling control is obtained by adding about 12 Ib of bentonite and 1 1/2 lb of soda ash per dry short ton of concentrate. These additives, and occasionally small quantities of fine coal, are thoroughly mixed with the filter cake ahead of balling. The swelling property of bentonite improves the green and dry strength of the balls so they can be handled without breakage until they are fired. Soda ash is added for pH control to insure maximum performance of the bentonite, and coal is added for more heat in the firing process when required. The balls, normally 3/8 to l-in. diam, are brought to a temperature of 2350" to 2500°F in the indurating furnace. Heat for this process comes from three sources: 1) fuel burned in the combustion chamber, 2) oxidation of the magnetite concentrates to hematite, and 3) coal added to the balls. Pellet strength is developed by grain growth and bridging and, if enough slag-forming constituents are present, by slag bonding. Conversion to hematite is usually close to 100 pct in the fired pellets. Batch Test Procedures: Initial studies of self-fluxing pellets were made by producing balls on a batch basis under carefully controlled laboratory conditions. The l-in. balls, uniform in size, were fired in an oxidizing atmosphere in a standard laboratory muffle furnace. The firing procedure consisted of

Jan 1, 1961

By W. L. Connell, O&apos

The properties of some heavy liquids which can be used in sink-float separations are discussed with major emphasis being given to the halogenated hydrocarbons. Data are presented on density, viscosity, thermal characteristics and the effects of moisture and temperature on the corrosiveness of the liquids towards various materials of construction. The toxicity of these materials, the hazards involved in handling them, and the procedures for handling them safely are also discussed. True liquids have certain advantages over colloidal suspensions for sink-float separation of minerals which makes their use especially advantageous when close separations, fine particle sizes or water-soluble minerals are to be treated. For best separating results, the medium should have an easily controlled, uniform, stable density. Here, true liquids have the advantages of allowing closer control of density and of not requiring agitation to maintain a uniform den- sity in the equipment. Low viscosities are desired in a separating liquid so that rapid separations of fine material can be made. Many liquids have lower viscosities than the colloidal suspensions at operating gravities of 1.4 to 5.0. For economic reasons and to prevent contamination of the product, the separating medium must be easily and completely removed from the ore. Normally, true liquids must be more completely removed than the cheaper suspensions and thus cause more problems in this area. The fact that the medium should not react with the minerals, air, water or the common materials of construction limits the choice of liquids which can be used, but many are available which are sufficiently stable. A more serious objection to the use of true liquids is that many of them present a toxic hazard to operating personnel and users of the product. Most true liquids are toxic to some extent, but modem knowledge of toxicity allows us to recognize the hazards inherent in handling them and enables us to design around them. Three types of true liquids are available for this use: 1) Halogenated hydrocarbons cover the gravity range from 1.2 to 3.3. They are generally more volatile and less viscous than the other liquids.

Jan 1, 1963

By K. W. John, L. Mueller

The rock mechanics approach to stability problems of steep rock slopes dealt with in this article has particular reference to the concept and methods of analysis developed by the Salzburg, Austria, school of rock mechanics. These theories are based on the principal postulate of the anistropy of the technological properties of in-situ rock masses. The present approach, which is more in line with geological engineering concepts, differs distinctively from the soil mechanics and engineering geological concepts commonly practiced in the United States. PRINCIPAL ENGINEERING APPROACH TO GEOTECHNICAL PROBLEMS AVAILABLE ENGINEERING CONCEPTS At the present time two different concepts are available for engineering analysis of underground structures and foundations in different earth material: soil mechanics and rock mechanics. Of these two branches, soil mechanics is, after 40 years of initially revolutionary and more recently evolutionary development, well established. Its principal concept of replacing in-situ soils or rock masses by perfectly homogeneous substitues has resulted in many practicable methods of analysis which, if applied with judgement, have resulted in successful applications throughout the world. Conversely, rock mechanics is still in the early stages of revolutionary development. Few, if any, standard concepts or methods of analysis have been established. Opinions vary widely. At present the professional background of an investigator very often determines the engineering concept to be applied to a particular problem, rather than its actual requirements if considered objectively. This paper stresses the rock mechanics or geological engineering point of view advocated by the Salzburg group. A review of the soil mechanics concepts is considered beyond the scope of this paper. THE "SALZBURG APPROACH" TO ROCK MECHANICS The rock mechanics concept as outlined here was initiated by Stini, based upon work by sander.1 Since

Jan 1, 1963

By J. E. House, C. J. Lewis

In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-pregnant sulfuric acid leach solution is contacted with an organic extractant dispersed in kerosene; the uranium enters the organic phase and associates itself with the organic extractants. Simultaneously an-ions or cations, as the case may be, leave the organic extractant phase and enter the aqueous phase. The two phases are then allowed to separate by virtue of their immiscibility. Based on the data available, a generalized procedure for the recovery of molybdenum from the sodium carbonate scrub liquor of acid leach uranium mills using secondary and tertiary amine extractants is presented, as is another generalized procedure for the recovery of molybdenum from the bleed stream of alkaline leach uranium mill circuits. Such economic appraisal as can be made at this stage of the development is also indicated. Molybdenum occurs in most uranium ores. Whether the uranium is solubilized by the acid leach route or by the alkaline leach process, some of the molybdenum present in the ore is solubilized along with the uranium. Molybdenum in uranium mill pregant solutions may cause processing difficulties, among which may be mentioned the poisoning of resins, the precipitation of organo-molybdenum complexes, or the build-up of molybdenum in recycle streams. While the uranium milling industry has been successful in applying measures to overcome the problems arising from the presence of molybdenum in the circuits, such measures nevertheless add to the cost of producing uranium yellow cake concentrate. Table I shows the analysis of typical uranium pregnant leach solutions. Uranium recovery by solvent extraction is presently practiced only in conjunction with acid leach circuits, and it may be noted that of about 16,000 tons of uranium ore daily processed by sulfuric acid leach, more than half of this tonnage follows the solvent extraction route. Uranium mills leaching ore with sodium carbonate-sodium bicarbonate solution (the so-called alkaline leach circuit) do not use solvent extraction. In this case the uranium pregnant solution is sufficiently pure to permit the direct precipitation of uranium concentrate with subsequent recycle of the alkaline leach solution. While solvent extraction procedures may be developed which are economically attractive for the alkaline leach uranium process, this has so far not been the case. The earlier uranium mill solvent extraction circuits used organo-phosphate extraction reagents, among which di-2-ethylhexyl phosphoric acid was popular. It should be borne in mind that uranium in its sulfuric acid leach solution exists in an equilibrium involving uranium in both anion and cation forms: uo + 2S0 = [uo2(so4)2] For this reason uranium may be extracted by either cation extractors or anion extractors and this is likewise true of molybdenum. However, the organo-phosphate extractants also load ferric iron which is usually present in the uranium acid leach solution. For this reason, it is necessary to reduce this solution substantially to the ferrous state ahead of solvent extraction using organo-phosphate reagents. The amines, being anion extractors, selectively reject iron and thus render the iron reduction step unnecessary. In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-

Jan 1, 1961

By S. M. M. Safvi, A. Jowett

Small-scale continuous flotation tests are described in which the influence of 1) pulp density and 2) feed rate on the rate of flotation are investigated. The results provide further evidence of first-order kinetics for flotation and indicate that tests at different feed rates provide a particularly simple method of determining rate constants. Flotation kinetics are discussed in general terms. Over a period of many years numerous research workers have studied the rate of recovery of valuable materials from flotation pulps with a view to deter-mining the mechanism of the froth flotation process. Froth flo ation is fundamentally a collision process involviug at some stage collision and then mutual attachment between air bubbles and mineral particles. It is possible to draw analogies therefore between the flotation process involving mainly macroscopic particles and the ordinary processes of chemical reaction kinetics involving collisions between atoms, molecules and ions. By adopting this analogy we may postulate a general equation representing the kinetics of the flotation process: -dC/dt =K.CC ,Aa (1) The rate constant, K, will be a complex function involving reagent concentrations, particle and bubble sizes, induction times and no doubt flotation cell design. However, these are factors which can be kept constant in any series of experiments, permitting investigation of the exponents a and c, which determine the order of the reaction occurring in flotation. The various research investigations carried out so far have all aimed at evaluating a and c and in the majority of cases only since the concentration of air has usually been kept constant in a series of tests, so that a relationship of the following type has been investigated: -dC/dt = K1 Cc (2) The techniques of both batch testing and continuous testing have been used to investigate this relationship. The technique of continuous testing, in which steady-state conditions are established, permits direct investigation of the above equation. In the case of batch testing, C is decreasing continuously

Jan 1, 1961

By David R. Mitchell, Ernest M. Spokes

There is evidence that study of minerals now considered to have susceptibilities too low for magnetic separation should be continued. Present concepts may be false. INFORMATION on magnetic properties of minerals other than magnetite is scanty and sometimes erroneous. Often there is no information at all. W. R. Crane&apos;s table of tractive forces published in 1901 is still the best guide in the field, but Crane&apos;s data can be used as a guide only, since he ignored such important factors as impurities in the minerals, size, and packing effect. During the 1930&apos;s work by the U. S. Bureau of Mines added greatly to knowledge of the behavior of certain minerals in a magnetic field. The USBM bulletin gave for the first time complete magnetic characteristics for magnetite and fragmentary data for a few other minerals. The work reported here covers a study of the magnetic-susceptibility relationships of the wolframite series of minerals and sphalerites as related to their chemical compositions. Theories are proposed to explain divergences found from commonly accepted beliefs. Gouy Method for Determining Magnetic Susceptibility: The Gouy principle has been adequately described in the literature1-3 and applied in various ways.&apos;- It may be summarized by stating that a body of material (gas, liquid, solid, or powder mixed with gas or liquid) of cylindrical shape changes in apparent weight if suspended with one end in a zone of higher magnetic field strength than is found in that portion of the field surrounding the other end of the cylinder. This may be expressed as K2 - K1 A (H2 - H2) - mg. [1] In determining the susceptibility of mineral specimens by the Gouy method, the mineral is reduced to a fine powder and packed in a glass weighing tube. Precise measurement of the bore and depth of the tube is made unnecessary by a calibration procedure. Using the basic expression of Eq. 1, Hoare"

Jan 1, 1959

By L. W. Pommier, F. B. Brien, A. K. Bhasin

In the field of mineral processing, although many operations are applied to suspensions of ore particles in fluids, there is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. Previously proposed equations, based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids, are exam ined in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. As more knowledge is acquired in regard to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow predictions of conditions to achieve optimum results for engineering purposes. In the field of minerals processing, many operations are applied to suspensions of ore particles in fluids. The differential movement of solids of various sizes and densities in suspensions is of utmost importance to gravity concentration, wet classification, flotation, hydrometallurgy, and pipeline transport of solids. The subject is also of importance to other branches of engineering; for example, those involved with soil mechanics, ceramic slips, and oil-well drilling fluids. There is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The problems encountered in the direct application of the well-known Stokes and Newton&apos;s Laws to non-Newtonian systems have been examined in a previous paper.&apos; Equations were proposed based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids. This present paper examines these equations in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. It is thought that, as more knowledge is acquired as to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow prediction of conditions to achieve optimum results for engineering purposes. The purpose of this paper is to make an initial assessment of the nature and magnitude of pertinent suspension variables. In order to avoid too voluminous a document, the examination of kinetics and mechanisms will be omitted at this time. THEORY A Newtonian fluid is defined as a fluid in which the stress is proportional to the rate of strain, 2 i.e.: H = viscosity; see Table I. for list of symbols The following equations are conventionally used to assess the motion of spherical particles moving under laminar and turbulent flow conditions through Newtonian fluids: When these relationships are applied in practice to suspensions, the liquid density is substituted by a composite suspension density, and viscosity is usually taken as that of the suspending liquid or an approximated "apparent viscosity." However, suspensions are non-Newtonian in character3 and thus, more than one viscosity parameter is required to describe their behavior. A number of models have been proposed for non-Newtonian fluids;2,4 among these the simplest is the Ostwaldde Waele or power-law model for incompressible fluids which for one dimensional flow may be reduced to:

Jan 1, 1970

By K. C. Ko, D. A. Pifer

The theory of probability with respect to the failure of structures is discussed. It is shown that the probability of safety, probability of failure, and factor of safety are directly related to each other and that as standard deviation approaches zero, the probability curves approach a unit step function which can be interpreted as the conventional factor of safety. The factor of safety is numerically the ratio of the load to the strength of the material at a particular point or plane in an engineering structure. Mathematically, it can be illustrated as a unit step function undefined at the point where the factor of safety is one (Fig. 1). The uncertainty of variation of soil and rock strengths require factors of safety much higher than those used in other engineering structures. The factors of safety used are generally determined from past experiences with similar structures. However, the factors thus determined do not have any theoretical meaning or do not indicate any relationship to actual safety.&apos; It seems, therefore, logical to develop a system with a sound theoretical basis to obtain a more suitable factor of safety for structures. An application of elementary theory of probability indicates that it is possible to relate this number to theoretical and practical engineering facts.

Jan 1, 1971

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and requires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged because a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced. Difficulties sometimes encountered in continuous filter operation can be summarized in the following four categories: 1) Low filtration and/or washing rates due to blinding of the filter medium. 2) Poor cake discharge resulting from sticky cakes, filter medium blinding, or too thin a cake for the particular type of filter. 3) High filter media costs caused by short life and frequent down times for cloth changing. This results from blinding or from abrasion by the scraper blade when cakes are thin. 4) Blowback of filtrate at cake discharge because not enough air passes through the cake to purge the drainage area and filtrate lines during dewatering. To reduce or eliminate blinding tendencies several modifications have been tried, for example, cover-cleaning showers, blowback under the feed slurry, and snap-blow cake discharge. In many cases, however, this simply retards the rate of blinding, since the filter medium is kept clean at its outer surface only by these methods. As blinding usually occurs within or on the back of the medium, the operator is finally forced either to remove the cloth and scrub the medium intensively with a cleaning solution or acid-rinse it on the filter—all resulting in down time, short cloth life, and additional costs.

Jan 1, 1959