Search Documents

By W. McMahon

Following the Sago Mine accident, the Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 1-ft resolution map of the mine to produce a 3-dimensional (3-D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3-D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals, and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling, and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jan 1, 2009

By P. J. D. Lloyd

The widely employed IPCC models for the release of methane from underground coalmining operations are reviewed, and put in the context of the South African National Communication on greenhouse gas emissions. Then attempts to calibrate the model via measurements on South African coalmines are described. These attempts failed because it rapidly became clear that the IPCC model, involving methane adsorbed by the coal and released (a) by the depressurization of the strata caused by mining, (b) from the broken coal and (c) from coal remaining in roof, floor, pillars or goaf after mining, was not valid. Instead, measurements showed that the methane release was very variable, sporadically falling to zero. Carbon dioxide concentrations were monitored at the same time as methane, and followed methane concentrations. An alternative model was developed, in which methane was largely displaced from the coal and held in fissures, cleats and pores, which, when intersected by mining, released methane into the ventilation stream. In a key test of this hypothesis, methane concentrations around a continuous miner were monitored both during operation and after shutdown. Even during operation, methane became undetectable. It is hypothesized that heating of the South African coal-seams during the emplacement of the igneous dykes that cut so many of the seams caused displacement of the methane from the coal into the pores. This fissure-held methane, or free methane, is released rapidly once a pathway through the coal into the mine atmosphere is established. In contrast, methane adsorbed in the coal, and measured as the seam gas, desorbs relatively slowly. Measurements suggest that on average about 50%of the adsorbed methane is lost one day after mining. By that time, the coal will have left the mine, so that the remaining seam gas will be released to the atmosphere outside the mine. Attempts to measure methane emissions from surface coal-mining operations showed very little detectable methane. Coal from surface operations, which was milled and exposed to atmosphere, adsorbed gas from the air. It is concluded that methane release from surface operations is probably less than 3Gg/a. It is estimated that the total methane release from the coalmining industry amounts to about 72 Gg/a, as opposed to the National Communication estimates of 323 Gg/a in 1990 and 317 Gg/a in 1994. However, there are large errors associated with these estimates, and it is recommended that the methodology outlined in this report be extended to as many mines as possible to reduce the errors that are inherent in the physical processes underlying the release of methane from South African coalmines.

Jan 1, 2005

By H. J. Glass

Collection, preparation, and analysis of blasthole chippings is expensive. Frequently, interpolation of grades at unsampled locations is considered using techniques like kriging. A pre-requisite for kriging is that an experimental variogram is established. In order to assess the quality of the experimental variogram, a measure is developed in this paper. The measure is derived from analysis of the time-honoured expression relating the variance, semivariance, and covariance. It reflects the weighted average deviation of the summed semivariance and covariance from the biased variance. The proposed measure allows assessment of the influence of key variables on the quality of the variogram. Using simulated data, it follows that the quality improves with an increasing number of samples, increasing density of the sampled locations, increasing regularity of the sampling pattern, and increasing uniformity of grades in the absence of correlation. Application to real data shows that the minimum number of samples could coincide with a marked decrease in the value of the measure. Establishing a threshold value is subject to further research. Keywords: variogram, variance, covariance, semivariance, minimization, sampling.

Jan 1, 2003

By T. Serradj

A study has been carried out to: develop a method for routine characterisation of rock strength and drillability through the particle-size distribution of crushed or drilled rock products, defined by the Protodyakonov index; establish correlations between the Protodyakonov index, uniformity coefficient and the constant grading equations; and propose an alternative rock characterisation index to classify rock strength and drillability for the northeast region of Algeria

Dec 1, 1996

By A. C. Apling, N. B. Barrett

Roadstone production requires the generation of non-flaky material, as outlined in British Standard 812 section 105.1; with respect to this criterion, a mathematical model of a cone crusher must be able to predict the flakiness index of a particular size range as determined by the relationship between thickness and nominal size. The Whiten cone crusher model utilises breakage and classification functions to predict a product particle size distribution only, so a shape function has been proposed that is based on a phenomenological approach, taking into account the transfer between flaky and non-flaky material at each stage of breakage. The results of laboratory tests to determine material breakage characteristics and of examination of pilot-scale test products illustrate the method's potential

Apr 1, 1995

By Joachim Lemke

The stainless steel sheets of permanent cathodes at Norddeutsche Affinerie (NA) were damaged by corrosion after nearly 11 years in operation. The necessary raising of the strength for stripping the copper had increased the deformation of the stainless steel blades. Current efficiency declined. After investigating the possibilities, like buying new cathodes or treating the steel surface, i.e. by sliding, a repair process was developed whereby the stainless steel sheet was exchanged. Special laser technology for cutting used blades und welding new stainless steel sheets underneath the used hanger bar was applied because the energy input into steel is the lowest of all welding methods. The new stainless steel sheet was welded with the rolling line in a horizontal direction. The achieved flatness of the repaired cathode blades amounted to less than 4mm per meter. During 11 months NA repaired nearly 36,000 permanent cathodes and put them back into operation. Repair costs were much lower than the costs of buying new ones and current efficiency increased again to more than 96% with a current density of 340 A/m².

Jan 1, 2006

By Syd S. Peng

University research in the U.S. consists of three components; faculty, funding, and graduate students or postdoctorals. Individual faculty is the unit area of research that is not limited, although faculty normally performs research in their areas of expertise. Faculty can and often do join with other faculty in multidisciplinary research. Faculty research achievements or reputation reflects the standing of the program and university. Therefore, research is highly encouraged and regarded within the university community. Graduate students are the work force of faculty research and doctoral students are preferred for high-quality products. The federal government provides the majority of funding sources, with the remainder coming from industry, state government and others. Compared with other engineering majors, the mining engineering programs in the U.S. are unique in that they: ? Are small in terms of the number of programs, and number of faculty and students in each program. ? Serve a single industry (i.e., mining) and are thus cyclic, reflecting the up and down economic state of the mineral industries. Enrollment statistics during the past 70 years show that a cycle consists of approximately 30 years with the first 10 years up, followed by 20 years down. ? Have curriculum designed to emphasize and thus serve for either the coal, hardrock or industrial minerals industries. These unique features make mining engineering programs hard to manage in university environments. Funding for mining research has relied primarily on the federal government, i.e., the former U.S. Bureau of Mines (USBM) and currently the National Institute for Occupational Safety and Health (NIOSH). The mining industry does not directly perform, nor sponsor research projects. Federal funding provides primarily in-house research. In the last four decades, federal extramural funding was only available when Congress appropriated extra funding in response to mine disasters. For instance, a string of coal mine explosions in the mid to late 1960s prompted Congress to enact the Coal Mine Health and Safety Act of 1969. It provided massive research funding from 1970 to 1983 covering all mining-related subject areas. From 1984 to 1995, federal extramural research funding was minimal, through two generic mineral technology research centers for selected mining engineering programs. In 1995, Congress closed the USBM and transferred the health and safety of miners program to NIOSH. Federally-funded extra-mural research practically stopped from 1995 to 2006. In 2006 and 2007, in response to a series of disasters, including those at Sago, Aracoma, Darby and Crandall Canyon, Congress again appropriated funding for short-term re-search in selected subjected areas such as underground tracking and communication, mine seal and ventilation, and deep cover pillar extraction. Therefore, to develop a meaningful academic mining research program during the past three decades, funding needed to be drawn from other sources such as the mining industries. A ?meaningful? program requires a sufficient amount of consistent funding in order to produce effective results. A review of federally funded extramural research pro-grams shows that a great majority of contractors/grantees are private entities, involving few mining engineering faculty. This, in part, is due to the fact that mining engineering involves so many different subjects. Therefore, a small mining engineering program can only have resources to cover teaching in the core subject areas (i.e., extraction, ground control, ventilation and material handling), at best. In this respect, a successful and meaningful academic mining re-search effort requires strong supporting programs such as geology/geophysics, structural (applied) mechanics, material sciences, compute/software application, etc. Therefore, academic mining research had to rely on private sources such as coal companies, in the author?s case, for sustained funding in the past three decades. Relying on funding from coal companies presents several problems. The projects were small and considered routine consulting projects requiring practical answers in a very short time frame. This is not really suitable for academic research, for which the major goal of research is the training of graduate students. These short-term projects vary with time and mines, most of which are driven by U.S. Mine Safety and Health Administration (MSHA) or U.S. Office of Surface Mining (OSM) regulations. So sustained funding under such condition requires broad experience of coal mining operations, which is also not well-aligned for academic research where faculty tends to specialize in a narrow field. Consequently, under such a funding environment, it is important to keep in mind how to develop long-term academic research objectives from conducting small short-term consulting projects that require quick solutions. In other words, how to look beyond the quick answers and to develop broader and more fundamental theories applicable to other situations that advance the-state-of-the-art. In order to achieve this objective, faculty must act as the connecting link because graduate students come and go. Faculty must know the detail of each project such that they know what are the important unsolved problems, what to assign to specific graduate students and how to guide the next group of graduate students to continue the development and advance the mining science. Under such funding environments, the most effective way to conduct academic mining research and ensure quality products is to maintain a research group consisting of postdoctoral, PhD, and MS students of various rankings such that the senior ranks can assist in guiding the junior ranks, especially the senior PhD students who are experts in their dissertation research areas. A weekly meeting should be scheduled for the group in which problems encountered in the research are discussed or individuals take turns presenting the progress of their projects. During each meeting, the importance of open discussion on scientific issues must be emphasized. Thus, opinions are encouraged, debated, and rejected or accepted. Students are encouraged to listen to and analyze other points of view. In addition to training of this thought process, the meeting also helps identify the strengths and weakness of each individual. As the subject of research expands over time, the group?s and, thus, the faculty?s research experience broadens. With this approach, companies can get the quick answer they desire from expert research experience and the faculty can engage in meaningful applied and basic research that is most relevant to routine mine operations. The end result is that companies will have a high regard for academic mining research.

Jan 1, 2009

By M. Shahabi, M. Kashfi

This paper briefly describes the excavation procedure of a powerhouse, comprising of its incremental excavation, reinforcement measures, and the installed monitoring system. During the first phase of excavation, the data obtained from monitoring of the behavior of Mudstone layers were used to recommend extra support measures. These data are also used to design the support of the powerhouse during its extension phase. In diesen bericht wird die bohrmcthode von kraftwerk ecavation in stupenweise dargestelt, und in die richtung d.sicherung, Mit hilfe von monitoring systeme. Die monitoring in (mudstone) schichten ist an schutz in bohrung entworfen und montiert in diese methode in K.W. fase 1 schutzung das K.W. in erweiterung der K.W. das berte auserwelt worden ist Cet article décrit brièvement le procédé d'excavation d'une centrale électrique, comportant de son excavation incrémental, de mesures de renfort, et du système de surveillance installé. Pendant la première phase de l'excavation, les données obtenues à partir de la surveillance du comportement des couches de schiste ont été utilisées pour recommander des mesures supplémentaires de soutien. Ces données sont également utilisées pour la conception de la soutènement de la centrale électrique pendant sa phase d’extension.

Jan 1, 2003

By K. L. C. Gonçalves, V. K. Alves

"CVRD’s Department of Development and Technology – GETEK has been developing and perfecting a general methodology for scaling up flotation and grinding circuits over several years. This methodology has been applied in several prospective CVRD mining projects. It encompasses a procedure for variability analysis based on bench scale tests, pilot scale grinding and flotation tests and modeling and simulation for scaling up the industrial flowsheet.The bench scale tests include the determination of the Work Index, simplified DWT tests, rougher flotation and locked-cycle tests with samples that are representative of the ore body variability. After completion of these studies, continuous, pilot-scale flotation tests are carried out at a Mini Pilot Plant with drill core samples representative of different stages of the mine life. Finally, studies are carried out with large volume samples using a conventional grinding and flotation pilot plant. This sample is also used for liberation characterization, grinding kinetics, flotation kinetics and industrial circuit scale up. This methodology has been successfully employed in the development of CVRD’s new mining projectINTRODUCTIONCVRD has been developing and perfecting a general methodology for scaling up flotation and grinding circuits over several years. The definition of the processing route and the sizing and scale up of the processing system are some of the products generated during the pre-feasibility of a greenfield project. This paper is focused on the scale up of grinding and flotation circuits, operations known to be of the most importance in a mineral processing plant.The methodology for the definition of the flotation and grinding circuits is divided in the following stages: bench scale ore variability studies, pilot plant operation and modeling followed by simulation. The product of this work is a calibrated simulator that can be utilized for plant operation as well as mine planning, looking to achieve optimal operational conditions.The current models used for scale up of the grinding circuits are aimed at the generating information about the size distribution of the circuit product. However, it is well known that the liberation state of these products may be of critical importance for the performance of the concentration processes downstream. Nevertheless, CVRD has been developing a methodology for liberation kinetics during grinding, aimed at optimizing grinding circuit throughput together with downstream flotation recovery."

Jan 1, 2006

By E. V. Lilford

A number of countries have introduced codes governing the valuation of mineral assets and securities. The African continent will follow suit in due course considering the importance of the global minerals industry as it relates to the attraction of foreign investment. South Africa is to introduce the Petroleum and Minerals Development Bill legislating the involvement of previously disadvantaged individuals and communities in the country?s minerals industry. One of the challenges facing the successful implementation of such codes and bills lies with the abilities of independent valuators to value mineral properties and projects on a consistent basis. Certain valuation principles and methodologies are applicable in all jurisdictions in the minerals industry. These valuation tools and principles are considered and developed in this report. They have been discussed and developed to encourage minerals valuators to consider and consistently apply the most applicable valuation methodologies.

Jan 1, 2002

By K. Morin

"Silver and gold leaching by cyanidation is a well-known process used around the world. This reaction is often accompanied by the leaching of other species throughtout the cyanidation circuit that causes the diversion of cyanide towards non valuable by-products (SCN-, Cu(CN)x, Fe(CN)x, etc.). One of the detrimental impacts of the formation of these by-products is the precipitation of silver-cyanide complexes that occurs when cyanide concentration is too low. Without any extra-addition of free cyanide, the precipitated silver is lost and cannot be recovered causing an important economic loss. To overcome silver precipitation, cyanidation circuits are often operated at higher cyanide concentrations. Recently, COREM’s research team has been working on a technology to measure and control silver precipitation during the cyanidation process. Moreover, a methodology has been elaborated in order to evaluate threshold cyanide level which corresponds to the cyanide concentration at which silver starts to precipitate. This technology has been tested on site on a real cyanidation circuit at Agnico Eagle’s LaRonde mine."

Jan 1, 2014

By T. Bajpayee, L. Prosser, A. Iannacchione

Reducing the number of roof fall injuries is a goal of the NIOSH mine safety research program. Central to this effort is the development of assessment techniques that will help to identify the nature of the risks associated with working under potentially hazardous roof conditions. This paper discusses a method to determine the roof fall risk using a qualitative risk analysis technique. The ability to determine roof fall risk has been a long-standing goal of safety professionals and can provide the kind of information, needed by on-site personnel responsible for worker safety, to mitigate roof fall injuries.

Jan 1, 2007

By L. R. Moore

Arsenic is among the list of major contaminants in mining aqueous waste streams. Though the elemental form is toxic, the aqueous oxyanions are more so. The most common forms of arsenic released during mining processes are arsenate and arsenite. The common treatment technologies to date can be summed up in these major categories: oxidation, coagulation, absorption, and media filtration. These methods can often involve many expensive processing steps that may also be limited by variables, such as total dissolved solids, other cations and anions, and the oxidation state of the arsenic. An innovative technology, falling in the absorption category, was developed that can successfully reduce such aqueous forms to a level below the EPA recommendations. This new technology offers a unique and viable solution which is transparent to the above mentioned limitations.

Jan 1, 2012

THIS bulletin presents all analytical and lest methods regularly used by Bureau of Mines laboratories for characterizing coal and coke. To provide better service to coal producers and consumers, the scope of this bulletin has been expanded to include important test methods used to evaluate coal properties for commercial processing. The methods described will prove valuable to all persons interested in analyzing and testing coal and coke.

Jan 1, 1967

By N. C. Matheson

The West's Shell Pile has been used on sites with very soft ground conditions for over 60 years. Fibre reinforced precast concrete shells 900mm long are threadled onto an internal mandrel which can be extended according to the depth driven to attain the load bearing resistance. On completion of driving the mandrel is removed leaving the precast shells to form a permanent lining to the cast insitu concrete core. To give resistance to high contamination, a tar based epoxy coat is sprayed on the outside of the shells or a flexible PVC liner is installed inside the shells to protect the core. Fundamental to the resistance to contamination is the quality of the precast fibre reinforced concrete shell, the mix design and method of manufacture. A series of detailed laboratory experiments were carried out using samples immersed in concentrated acid and sulphate solution. The long term effects of exposure to contamination is recorded in the case studies of existing piles at two gasworks sites.

Jan 1, 1989

By Claude Cunningham

The primary reason for blasting is to fragment rock. In production blasting, the fragment sizes produced are known to exercise an overwhelming influence over working costs: handling costs and tonnage throughput are directly affected by secondary breaking, loading and crushing, all functions of fragmentation. In addition, particular size fractions are frequently of intense interest in terms of market or process requirements.

Jan 1, 1995

Fine coal is defined as material with a maximum size of 1/2 in. Various methods for separate washing of such coal are discussed briefly because separate treatment can lead to a higher overall recovery of coal or to a product having a lower ash content.A felspar jig is discussed in detail because it is the method most recently adopted in Australia, and because it has the advantages of compactness, flexibility and automatic Gontrol, with minimum operator attention. This jig has a variety of adjustable controls to enable the desired results to be obtained from a wide range of coals and the general application of each control is discussed.The only separate treatment of fine coal in the Illawarra district is by felspar jigs on Bulli seam coal.INTRODUCTIONAll reasonably large Australian collieries now win coal by mechanical methods. but while mechanization leads to more economic production of high tonnages, it also changes the characteristics of the coal won. In particular there is an increased proportion of fines, and an increased ash and moisture content. However, specifications of coal for sale have become more stringent, and consumers now require coals in a definite size range with a lower and more uniform ash content, as well as with a low and uniform moisturecontent.These factors have led to the need to wash and grade run-of-mine coal at the pithead. In' plants where the whole of the run-of-mine coal is treated in a jig, some of the fine coal in the feed is beneficiated; the extent depending on factors such as the type of coal and the feed rate. However, for dense medium treatment, fine coal must first be screened out, and there may then be no washing of fine coal at all.

Jan 1, 1961

By W. M. G. Heeley

In the province of Alberta the coal measures dip at so many different angles, between the horizontal and the vertical, that many different systems of haulage are in use. I will, however, only touch briefly upon the general -systems in use, and devote the major portion of this paper to a discussion of endless-rope haulage and its adaptibility to various conditions in coal mines; dealing in particular with the endless-rope haulage that was installed at Brule during the month of August 1923. In coal seams that are approximately level, and newly opened, hand-putting or tramming from the face is the cheapest, but when the mine is further developed tramming is out of the question, and the use of ponies is the next consideration. The time arrives, however, when mining reaches a point where the economical haulage of coal by horses cannot be done profitably, and then some system of mechanical haulage must be installed. The installation of any system should be carefully considered before any particular type of haulage is adopted, because a great deal depends upon the grade or dip of the seam. Motor haulage is impossible to operate profitably on a grade of over 6 per cent and, while it is possible to use ponies, on short runs, up to 9 per cent, some other means of main and secondary haulage must be installed when a 9 per cent grade, is exceeded. I will, therefore, deal first with secondary haulage, because even though a main haulage is established, secondary haulage can be used to feed the main haulage.

Jan 1, 1925

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By R. M. Jacobs

Can your company afford to issue a check today for $100,000, $500,000, $2,000,000, or $22,000,000? This is what it might cost your company if it is on the losing end of a product liability suit. During the past 10 to 15 years, the number of product liability actions has grown from a handful per year level to a hundreds of thousands per year level. Settlements and awards in the tens and hundreds of thousands of dollars are not unusual in these days. The largest award that the authors haw heard about is a case involving a private airplane and the death of four men, which was awarded over $22,000,000. In the materials handling field, a fork lift truck, ordered with an overhead guard, was delivered without a guard because one was not available at the time. An accident with serious personal injury followed. Wouldn't it have been better to have waited until the guard was available before delivering the unit? Answer: a quarter of a million dollars better -- the cost of the settlement. Hoisting devices are also not without their liability precedents. In a 1960 case, an employee was injured when a load abruptly fell from a hoist. It was determined that the operator could not possibly have caused such a fall had the hoist been functioning properly. The case was compounded when the manufacturer of the hoist contended that the load had been improperly connected to the device, since the same hoist was used to remove the weight from the injured man without another malfunction.

Jan 1, 1973