Search Documents

By W. Banda

Paper written on project work carried out in partial fulfilment of Phd. (Process Engineering) degree* The recovery of cobalt and copper from waste slag was studied in a plasma DC-arc furnace in reducing conditions. Three fluxes, CaO,CaF2, and TiO2, were investigated for their influence on selective recovery of cobalt into an iron-rich alloy. A further investigation on the influence of furnace power on the reduction of slag to recover cobalt to the alloy showed that a change in power setting had an unexpected effect on the recovery of metals to the alloy, in that selectivity of base metal recovery over iron recovery decreased at an increased power level. Keywords: DC-furnace, reduction, nonferrous, slags

Jan 1, 2004

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

By R. Laird Auchmuty

A NUMBER of factors, of varying importance, should be considered in assessing mineral land-here specifically coal land -for tax purposes. (1) Is the coal developed or un- developed'! (2) If undeveloped, is it surrounded by active development in adjoining properties? (3) Accessibility of railroad facilities to the property. Sometimes the railroad itself is of importance. (4) Cost of development of the seam under consideration, whether it can be developed by a drift from the outcrop or whether it will require deep and costly shafts or slopes. (5) Is it definitely known that the coal seam being assessed is of minable thickness and quality on the property? (6) Thickness of recoverable coal from the seam. (7) Quality of the coal. (8) Is the seam being assessed likely to be more costly to mine than other seams in the same district? (9) Is there an active market demand for coal from the seam being assessed? (10) Is the coal held only as protection to surface structures and in such location that it can never be mined? (11) Is the coal in a solid piece or is it in pillars that have been standing for some years as a result of incomplete mining in an old operation? (12) Expected percentage of recovery from the seam being assessed as determined by present mining practice in similar properties. (13) Value of the seam as indicated by sales of similar mineral rights in the immediate district. (14) Current royalty rates of leases for coal in the seam under consideration.

Jan 1, 1939

By Andy Fortin, André Vien, Christophe Bouché, Jeff McKay

"The technology and equipment design of the Twenty-first Century permit us to exploit low-grade ore bodies with milled tonnages reaching 300,000 tpd. Because of their substantial operational costs (energy, wear parts, etc) and precarious economic situations, the operations of today must maximize their metallurgical performance.The implementation of an Expert System becomes a logical avenue to pursue in view of increasing plant performance.Many operations, following the implementation of an Expert System, meet the objectives they determined before its integration; such as increased tonnage, stability, decreased costs, etc. However, they often cannot develop the full potential of the system due to certain factors that have been neglected or omitted during the implementation of the system.Three main elements have been identified during the implementation phase at INMET Mining Troilus Concentrator: 1- Instrumentation & Control 2- Software 3- Integration. Even though they have been clearly identified, these elements are often neglected due to lack of resources or lack of comprehension on the part of the operations personnel. This document will demonstrate, based upon our experience at Troilus and that of Metso Minerals, that we can identify and handle many factors which influence the profitability of the Expert System, for both short and long-term process control improvements.INTRODUCTIONThe Inmet Troilus Mine is an open pit mine, situated 175 km north of Chibougamau in the province of Québec, Canada. The mill, which started production in November of 1996, was originally designed to treat a gold – copper ore at a rate of 10,000 tpd.In early 1998, the mine plan called for a pit pushback and decreasing head grades for the following two years. With the price of gold nearing decade lows, the Troilus project was facing a major economical setback. There was a sense of urgency to reduce operating costs below the market price of gold. The mill team presented a project to management calling for an increase in mill throughput while minimizing capital expenditures and operating costs. This idea was supported by the existing mine plan, which called for a mine cut-off of 0.7 g/t Au and stockpiling low grade 0.5 g/t material for future milling."

Jan 1, 2003

By M. Ng

As part of a long-term study of titanium minerals processing being undertaken by the Julius Kruttschnitt Mineral Research Centre, techniques have been developed to measure the resistivity of ilmenite, rutile, zircon and other associated minerals. The techniques have proven reproducible and have allowed the measurement of resistivity under conditions of varying temperature, surface condition and surface moisture adsorption. The measured values can be linked to the separability of the minerals in the dry plant, and hence are useful as a diagnostic test for existing plants when performance deteriorates, or for greenfield sites to investigate potential problems. One of the major problems in electrical separation of titanium minerals is surface coating on the mineral grains. Coatings can make normally conductive minerals such as ilmenite and leucoxene behave much more like non-conductors. Electrical separation of surface contaminated ilmenite from non-conductors then becomes extremely difficult unless the surface contaminant is first removed. The resistivity measurement technique was used to evaluate the effect of surface cleaning on the resistivity of ilmenite and zircon from a Western Australian deposit which will shortly be in production. Ten different attritioning methods were evaluated, ranging from simple rinsing inwater to chemical attritioning in sulphuric acid combined with ultrasonic leaching. A roasting and quenching step was also investigated. As would be expected, the gentler treatments, such as rinsing in water or Calgon, had only amoderate effect on the ilmenite surface coatings. Ilmenite resistivity decreased by about 1 order of magnitude from 5.6 x108?m to between 2.5 and 4.4 x107?m. More intense treatments had a much more pronounced effect. The most effective, reduced ilmenite resistivity to 6.5 x105?m or three orders of magnitude. Zircon was relatively unaffected by any of the attritioning methods, with only a small increase in resistivity observed from 8.0 x1012?m to 2 x1013 ?m. The results show that measurement of mineral resistivity allows the effect of surface treatments to be easily quantified in a way that has benefits for greenfield site development where only small samples are available for testing. The effect of surface moisture has also been investigated using resistivity measurements. Measurements were made on zircon in an environmental chamber in which both humidity and temperature could be closely controlled. Zircon resistivity at 60 deg C decreased from 6 x1011?m at 5% relative humidity to 8 x108?m at 95% humidity. Moisture content and moisture re-adsorption from dry of zircon and number of other minerals were measured using a Mettler moisture analyser. Zircon adsorbed the least amount of surface moisture (0.05–0.09%) but re-adsorbed moisture from dry the fastest, reaching 98% of the original level in 10 minutes. Leucoxene adsorbed the most moisture (0.67%), but was much slower re-adsorbing this moisture from the dry state, reaching only 63% of the original level in 10 minutes. The difference was attributed to the surface characteristics of the grains, the leucoxene being much more porous than the zircon examined. The resistivities and differing rates of moisture adsorption can be used to quantify the effects of changes in atmospheric conditions of the performance of electrical separation in dry plants.

Jan 1, 2003

By R. J. Durheim

Detailed investigations have been conducted into 21 rockbursts which caused damage to excavations in deep South African gold mines, in many instances resulting in the death or serious injury of workers. The objective of this study is to determine the principal factors controlling the severity and distribution of damage, so that strategies to reduce the hazard of rockbursts may be developed. It was found that the source mechanism is often controlled by the mine layout, and regional structures such as faults and dykes; while local rock conditions and support systems strongly influence the location and severity of damage. In the short term the most important lever for reducing the rockburst hazard is the effective implementation of existing rock engineering knowledge and technology.

Jan 1, 1998

By David M. R. Stone

Underground mining in the gold industry is gaining popularity in Nevada, and with it the use of cemented rockfill is becoming mainstream. Even with today?s high metal prices, however, mining companies are very sensitive to the margins they realize, and are constantly looking for ways to reduce costs or improve efficiencies. Given that the backfill is one of the largest cost centers in underground mining, mines are constantly under pressure to reduce backfill costs. This paper will present an overview of the factors that impact cemented rockfill quality in Nevada mines based on the authors many years of consulting experience. Cemented rockfill quality can be linked directly to binder consumption, hence programs aimed at improving quality generally result in lower binder costs, better performance in the fill (hence less dilution), and improved safety. The paper will conclude with the key elements of a comprehensive program of backfill quality assessments and backfill QA programs. Comparative laboratory and minesite data from a number of operating and proposed mines will be presented.

May 1, 2007

Mining is a fundamental activity on which modern society and the world's economy are entirely dependent. Mining investors, large and small, invest on an international scale, frequently being active in several countries.   Prior to committing investment to new countries, the prudent investor will consider the risk involved by analysing a number of physical, financial, administrative and political parameters that impact on the potential financial returns it is seeking. This paper considers these risk factors in relationship to New Zealand and six competitor countries. The conclusion is that for reasons largely within the control of our politicians, New Zealand is a high risk country for mining investors.

Jan 1, 1993

By Thomas M. Barczak

Purchasing a new set of longwall shields requires a substantial investment. A poor shield design can lead to economic hardships, safety concerns for the mine workers, and closure of the mine. This paper addresses several key points that should be considered in the procurement process: (1) understanding your goals and the logic in selecting a higher capacity shield, (2) the importance of completing performance testing before production shield fabrication begins, (3) making sure performance testing is properly done, (4) measuring load(stress) development during performance testing, (5) testing a shield to failure, and (6) the value of buying extra shields. In addition, several challenges are proposed for consideration in future shield designs. These include (1) 100,000 life-cycle expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control by optimizing setting pressures, (4) lubricated link joint design concepts, (5) composite material applications to reduce shield weight, (6) incorporating periodic weighting predictive algorithms into the data-processing software, (7) advanced component load measurement on two to three specially instrumented shields to detect loading in the structural components, and (8) constant set leg cylinder design.

Jan 10, 2000

By Fred N. Kissell

In This Chapter [The explosibility of methane gas mixtures Effect of pressure and temperature on explosibility Less common sources of methane ignitions The amount of methane stored in coal Forecasting the methane emission rate Layering of methane at the mine roof When the recirculation of mine air is hazardous The importance of higher air velocity in preventing methane explosions and Mine explosions, barometric pressure, and the seasonal trend in explosions] Dealing with methane in mines and tunnels requires knowledge of the circumstances under which dangerous accumulations of methane are likely to occur. This knowledge involves the properties of the gas itself, an awareness of where these accumulations are likely to occur, and facts on how methane mixes safely into the mine air. The other chapters in this handbook address the handling of methane under a variety of specific circumstances, such as at continuous miner faces or coal storage silos. This chapter addresses some broad concepts that serve as a foundation for the suggestions provided in other chapters. THE EXPLOSIBILITY OF METHANE GAS MIXTURES Methane entering a mine or tunnel often enters as a localized source at high concentration. Figure 1–1 depicts a cloud of methane being diluted into a moving air stream. In this illustration, methane enters the mine from a crack in the roof. As the methane emerges from the crack, it progressively mixes with the ventilation air and is diluted. In the event that this progressive dilution reduces the concentration from 100% to 1%,2 as shown in Figure 1–1, the methane passes through a concentration range of 15% to 5%, known as the explosive range. In the explosive range, the mixture may be ignited. Above 15%, called the upper explosive limit (UEL), methane-air mixtures are not explosive, but will become explosive when mixed with more air.

Jan 6, 2006

By J. Paraszczak

High productivity of the equipment employed is one of the key factors in reducing production cost in mining. One of the best ways to achieve it is an increase in availability. In order to identify the most adverse factors affecting it, reliability and maintainability analysis ought to be done. If its results are to be conclusive, a sufficient amount of credible and consistent data is indispensable. Following the experience from field studies done in underground mines, this paper discusses the current status of failure and maintenance reporting, as well as problems encountered. It exposes the importance of adequate data collection on failures and downtime as well as it reviews the benefits of analysis based on such material. The question of benchmarking with regards to mining equipment performance is also addressed. The paper concludes with some recommendations on data collection and processing, as well as stresses the need to standardize the most important reliability/ maintenance notions throughout the mining industry and to conceive appropriate performance measures.

Jan 1, 2000

By Yingxin Zhou

Virtually every coal seam in Appalachia will at some time be subject to multi-seam interaction (Wu et al, 1987). Many such problems result from seams which lie in close proximity or have split and lie within thirty feet vertically of one another. Existing techniques for multi- seam design have concentrated on conditions where the entire inner burden is not the failing member and are unsuitable for ultra-close multi-seam design. Structural integrity of the inner burden must be maintained if two superimposed seams are to be mined separately and under- standing possible failure mechanisms of the inner burden is an essential first step in the design process.

Jan 1, 1989

By King E. J

Department of Pathology, British Post-graduate Medical School, London:The experiments here recorded were devised and carried -out during the last two years in an attempt to corroborate the important work of Denny, Robson and Irwin (1939) in which they found that experimental silicosis could be prevented by means of metallic aluminum. By causing rabbits to inhale powdered quartz for several months they induced experimental silicosis. These animals then served as controls for comparison with another group which were dusted with a mixture of quartz and aluminum. In the second group silicosis failed to develop.Our experimental procedure was somewhat different. We resorted to intratracheal insufflation instead of simple inhalation, and we used rats instead of rabbits: otherwise the essential features of the original experiments were carefully duplicated.EXPERIMENTAL PROCEDURES.A single dose of dust was delivered into the lungs of each animal. The dust was suspended in a fluid medium and injected by means of a syringe directly into the trachea in known quantity (technique of Kettle and Hilton, 1932). The suspensions were autoclaved before use and were injected with aseptic precautions. Having had a long experience of this technique we employed it with confidence and usually secured a fairly uniform dispersal of dust throughout both lungs. To carry out injections successfully one requires, above all, an even suspension of dust which will flow smoothly and quickly from the syringe. This is not difficult in the case of quartz, for, though it tends to settle out rather quickly, this can be avoided by constantly agitating the suspension. The syringe containing the inoculum may be shaken gently right up to the moment of injection and then emptied quickly to prevent sedimentation. Powdered aluminum is more difficult to handle, for the particles tend to flocculate and are not readily made to disperse evenly in saline, even by violent shaking. For this reason an emulsifying agent may be used to advantage, provided it does not complicate the experiment, a point to be mentioned again presently.THE EXPERIMENTSExperiments with quartz alone: Extensive silicotic lesions were produced in 23 out of 26 rats by the administration of pure quartz dust in doses of from 50 to 200 mg. per rat. The dust was so finely pulverised that the particles averaged about 1-p. in size: none was larger than 5 p. and 99 per cent. were under 2.5 p.Eight of these animals survived for seven months and were then killed...

Jan 1, 1945

Abstract : The computation of reliability index or failure probability of slopes can be transformed into an optimisation problem. In high rock slope engineering, it is usually a multimodal optimization problem. The traditional optimization techniques are difficulty to find out the global optimal solution because of their easily falling into local optimal value. Recently, a new kind of bionic algorithm - ant colony algorithm (ACA) - has been used to solve this problem. In this paper, the structure of ant colony algorithm and the transfer probability of ants are modified to evaluate the failure probability of complicated slopes. A new adaptive ant colony algorithm (AACA) is proposed to determine critical slip surface and its corresponding failure probability of complicated slopes. A case study is given to verify the proposed approach. The results show that the presented method has obvious advantages compared with traditional methods. ZUSAMMENFASSUNG: Die Rechnung des Zuverlaessigkeitindexes oder der Zerstoerungswahrscheinlichkeit kann sich in einer Optimierungsfrage umwandeln, im Bauprojekt an hoehe Gebirgehang, handelt es sich meistens um eine Optimierungsfrage ueber Multi- Spitzenwert. Mit der traditionelle Optimierungsmethode ist es schwer eine umfassende Loesung fuer die Optimierung zu finden wegen des leichte Verfallens in Beschraenkung der Teiloptimierungsloesung. Mit dem neue Bionik- Algorithmus —— Ameisen - Kolonie- Algorithmus wird dieses Problem geloest. In diesem Text hat man eine Strukturverbesserungsloesung fuer das Ameisen- Kolonie -system und die Wahrscheinlichkeit der Ameisenkolonie erwaehnt, und damit wird man die Zerstoerungswahrscheinlichkeit des komplizierte Hangs feststellen. Mit dem neuen Ameisen- Kolonie- Algorithmus kann man die gefaehrlichste Gleitflaeche und die entsprechende Zerstoerungswahrscheinlichkeit herausfinden. Die in diesem Text beschriebene Methode wurde durch Praxis geprueft. Durch die Pruefergebnisse wurde es gezeigt und bestaetigt, dass der neue Bionik- Algorithmus vorteilhafter als der traditionelle Algorithmus ist. Résumé : Le calcul de l’indice la fiabilité ou de la probabilité de ruptures peut être transformé en un problème de l’optimisation. Pour le cas du génie des pentes de haut rocher , le problème se pose en général en l’optimisation de multi-crêtes. Les techniques traditionnelles conduisent facilement à la solution optimal partielle au lieu de celle globale. Récemment un nouveau type de bionique algorithmique a été appliqué pour la solution de ce genre de problèmes, c’est l’Algorithme Colonie de Fourmis. Dans l’article il est proposé de modifier la structure du système de la colonie de fourmis et la probabilité de transfert des fourmis en vue d’évaluer la probabilité de ruptures des pentes de haut rocher complexes, par ailleurs un nouveau algorithme adapté de colonie de fourmis est formulé pour déterminer la surface glissante critique et la probabilité de ruptures correspondante. Les techniques proposées dans l’article sont vérifiées à travers des expérimentations dont les résultats ont prouvé que les techniques présentées dans l’article sont évidemment meilleures que celles traditionnelles.

Jan 1, 2003

By Walter F. Atkins

Fair market value, in the legal sense , is the price which a prudent and knowledgeable buyer and a prudent and knowledgeable seller, acting without constraint or compulsion , will agree upon to exchange an asset. In the ordinary commercial or engineering usage, the term may imply simply the market value or a reasonable and equitable price. The engineer evaluator who is called upon to express an opinion about the fair market value of an asset may be able to base his estimate on the sale price of similar assets or on the market values of stock. Frequently such indicators of value are not available and the evaluator must devise other means of appraisal. Mineral resource properties may be thought of as having value by virtue of the existing or potential ability to produce at a profit. Conventional procedures permit the computation of the present value of future revenues having due regard for the time value of money and the risks attendant upon the realization of the venture. Such computations have gained wide acceptance as a basis for the estimation of fair market value.

Jan 1, 1977

By N. L. ALISON

MUCH has been published on the general subject of metal mine ventilation but, so far as I can discover, few specific data on selection of fan equipment to meet the requirements of a given mine ventilation problem are available. This article is intended to point out some of the more important considerations which influence the selection of such equipment. It will be assumed that the mine operator is able to determine the quantity of air which is necessary in the various parts of his mine to produce the required results and the pressure in inches water gage needed to circulate this quantity of air through the mine. There may be instances in which this assumption is not justified, but the fact remains that, with proper engineering talent, these data can be approximated sufficiently close for practical purposes.

Jan 1, 1930

By B. G. Tarasov

This paper proposes the further development of a recently identified shear rupture mechanism (fan mechanism) that elucidates a paradoxical feature of hard rocks ? the possibility of shear rupture propagation through a highly confined intact rock mass at shear stresses that can be significantly less than frictional strength. In the fan mechanism, failure is associated with consecutive creation of small slabs (known as ?domino blocks?) from the intact rock in the rupture tip, driven by a fan-shaped domino structure representing the rupture head. The fan head combines such unique features as extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Consequently, the failure process caused by the mechanism is inevitably spontaneous and violent. Physical and mathematical models explain unique and paradoxical features of the mechanism, which can be generated in primary ruptures and segmented faults. The fan mechanism provides a novel point of view for understanding the nature of spontaneous failure processes, including shear rupture rockbursts. The process explains, in particular, features of shear rupture rockbursts such as activation at great depths, generation of new shear ruptures in intact rock mass, nucleation of hypocentres at significant distances from the excavation, shear rupture development at low shear stresses, and abnormal rupture violence.

Jan 1, 2014

The spatial and temporal evolution from the porphyry to high-sulphidation epithermal environment can be assessed by integrating new results on such deposits (Arribas et al, 1995; Hedenquist et al, 1998) with past studies of plutonic and porphyry systems (Dilles and Proffett, 1995; Cline, 1995; Shinohara and Hedenquist, 1997; Hedenquist and Richards, 1998). Some time ago, Sillitoe (1973) argued for the nature of the tops and bottoms of porphyry deposits. He concluded that epithermal deposits may form over the tops of some porphyry systems. We can now conclude more confidently what the tops and bottoms of many high-sulphidation ore deposits appeared like while active (Arribas, 1995; Hedenquist, 1995). In addition, we better understand the nature of the zonation of high-sulphidation epithermal systems from the intrusive to surficial environment (Sillitoe, 1999), and how these two styles of ore deposit are related. Geological and geochemical evidence clearly indicates a continuum between these two ore environments. This improved understanding of genesis allows more efficient exploration for these deposits. There are many examples of spatially associated porphyry and epithermal ore deposits. A genetic connection has been suggested by some, and argued against by others. Nowhere is this spatial association better seen than in northern Luzon, Philippines, where the Lepanto high-sulphidation epithermal Cu-Au deposit overlies the Far Southeast (FSE) porphyry Cu-Au resource (Figure 1). Together these mineralised bodies contain a resource of >3.8 M tonnes Cu and >550 tonnes Au. Lepanto was largely mined out in early-1997. Post-war production until 1995 was 0.73 Mt Cu, 115 t Au and 393 t Ag at an average grade of 2.2 per cent Cu, 3.5 g/t Au and 11 g/t Ag. The recent discovery of the adjacent Victoria low-sulphidation quartz-Au-base metal vein deposit, with a resource of >68 tonnes Au (Cuison et al, 1998), illustrates the variety and abundance of mineralisation in the Mankayan district. This district also hosts the Guinaoang porphyry Cu-Au deposit (Sillitoe and Angeles, 1985) and other epithermal vein occurrences (Figure 1). This brief summary reviews the results recently published on the Lepanto-FSE deposits (Arribas et al, 1995; Mancano and Campbell, 1995; Claveria, 1998; Hedenquist et al, 1998), and stresses the evidence for coupling of mineralisation between the porphyry and high-sulphidation epithermal environments.

Jan 1, 1999

By Robert Hopler

In issuing this pamphlet on stump and boulder blasting for the use of farmers, we wish to call attention to the fact that Du Pont High Explosives have been used with universal satisfaction for many years under diverse conditions, and have never failed to give satisfaction in mining, quarrying, roadmaking, blasting stumps and boulders, or for any other work where regard to economy and safety in use is the object.

Jan 1, 2008

Fast Adsorption Phenomena at Air/Liquid Interfaces

Sep 13, 2010