Search Documents

Develop a new technique of in situ rock stress measurement which can be used when and where the conventional methods, such as the overcoring stress relief methods and the hydrofracturing method, cannot be effectively applied. Approach The Bureau of Mines developed basic principles to determine existing biaxial stresses in rock mass by using an instrumentation package consisting of one 3.8-cm-diameter hydraulic cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated flat hydraulic borehole pressure cells (BPC) to he installed in a single drill hole.

Jan 1, 1988

By L. K. Marshall

Last month's engineering fundamentals article discussed some general considerations of underground mine ventilation. This month's article takes a look at auxiliary ventilation-brattice, fans, and ducting-in underground mines. The need for good, efficient auxiliary ventilation increases as mines get deeper and move farther from ventilation shafts. New mining methods and equipment resulted in faster work area advances, liberating more dust, gas, and heat. As a result, worker health and safety requirements in the face area have become more stringent. For all these reasons the safety and efficiency of any underground mine depends heavily on its auxiliary ventilation. The purpose of such ventilation is to supply sufficient quantities of clean air to the face of the drift and to maintain air quality within desired limits until expelled from the mine.

Jan 2, 1982

By Baker G

The exposures resulting from development work, following on the discovery of a new shoot of hIgh grade ore at the north end of the Sardine tin mine, during 1952, have provided an unusual opportunity to study the oxidation of a stannite-rich ore. Through the kindness of C. C. Morton, Chief Government Geologist of Queensland, an exactly located suite of specimens representative of the exposures was supplied by J. and W. Reddie. This was later supplemented by a number of specimens culled from a parcel ofrepresentative ore submitted to the Melbourne Ore Dressing Laboratory for testing.The Sardine tin mine, near Ewan, Queensland, has been the outstanding producer of the Kangaroo Hills Mineral Field. Since its discovery in 1918, up to 1952 it has yielded about 1,500 tons of cassiterite concentrates, and about 85 tons of stannite concentrates. The outcrop ore averaged 35% tin oxide, but the grade declined with increasing depth, and by 1930 had fallen to 7% tin oxide. In the northern section of the mine the ore shoots show a downward passage to complex primary s.ulphide ore, containing cassiterite and abundant stannite.The orebodies occur in a series of fissures in a crushed zone about 50 ft. wide in slates and quartzites that have been intruded by granite (Connah, 1952). A quartz porphyry dyke forms the footwall of the original main lode in its southern part, being traced' from the surface to' the No. 4 level (173 ft. vertical depth), and two narrow dolerite dykes were encountered in the workings north of the main...

Jan 1, 1954

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations.

Jan 1, 2002

By J. Hurdley, J. A. Plant, H. Robotham, P. R. Simpson, G. C. Lalor

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The results of orientation studies for a regional geochemical survey of Jamaica and the CARICOM countries of the Caribbean region are described. The survey is designed to provide systematic geochemical information for a wide variety of applications and, especially, to form a basis for agricultural development in the region

Jul 1, 1991

By Mark I. Copeland

The Bureau of Mines investigated the effect of up to 1 wt-pct of copper and silicon on the heat treatment response and hardness, tensile, and impact properties of hot-rolled medium-carbon steels. The steels were prepared by induction melting and fabricated into plates by forging and rolling. The tensile strength of 0.2-wt-pct carbon steels containing 0.3 wt-pct silicon was affected significantly by copper in both the hot-rolled and heat-treated (600° C) conditions, whereas the tensile strength of the 0.3-wt-pct carbon steels was less affected. A 600° C treatment was considered optimum as a post-rolling treatment to strengthen the steels by copper precipitation. Strengthening of 0.2-wt-pct carbon steels by silicon was reduced by increasing copper contents.. Optimum impact strengths occurred at about 0.3 wt-pct silicon in 0.2-wt-pct carbon steels containing 0.6 and 0.8 wt-pct copper. The impact strengths were lowest for 0.2-wt-pct carbon steels containing over 0.8 wt-pct copper and greater than 0.3 wt-pct silicon, especially in the heat-treated condition. Copper and silicon solutes and copper precipitates strengthened the steels. This effect was augmented slightly by strengthening through grain refinement by these solutes.

Jan 1, 1973

By L. J. Gardner

Ore pass systems play a critical role in moving broken rock from the workplace to surface, and the integrity of the ore pass excavations is crucial. Over the life of the mine, ore pass integrity deteriorates, which may eventually result in the ore pass no longer being fit for purpose. This paper presents several case studies of successful ore pass rehabilitation exercises.

Jan 1, 2006

By Stephen C. Tadolini, Dennis R. Dolinar

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that are easy to handle/install under temporary or previously supported roof.

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By Thomas C. Wilder

Jan 1, 1965

By J. Griesel, P. H. F. Bouwer, K. Bisaka

Transalloys produces 160 000 tons of SiMn per annum from five AC submerged-arc furnaces. The lime-ore melt from two AC open-arc furnaces is contacted with SiMn to produce 50 000 tons of medium carbon FeMn per annum. Metallics in the slag are reclaimed in a jigging plant, which has been in operation since 1999. The flow of materials between the jigging plant and furnaces has been optimised. The amount of recycle slag in the feed of the SiMn furnaces has been decreased by more than 30% which still provides satisfactory stability of the furnace operation. The jigging plant has absorbed all the additional slag generated, to recover SiMn metal. A review of the raw materials used and operating parameters for SiMn production was also undertaken. Slag to metal ratios were decreased by more than 30% by reducing the slag recycle, removing magnesite from the recipe and introducing high-grade ore. Electrode penetration was improved by reducing coke levels and by utilising more reactive coal. The pitch circle diameter (PCD) was reduced to get a better operating stability on furnace no 5 using the MINSTRAL Control System. Energy consumption on the furnaces improved by more than 15% while SiMn production increased as a result by more than 18%.

Jan 1, 2004

By Charles L. Kimbell

The year 1986 was not a good year for the world's mineral industry from several viewpoints. Levels of production, both of crude minerals and processed forms, registered declines in the cases of a greater number of commodities than the number that recorded increases. The overall value of world crude mineral production was estimated to have increased, but only very slightly in terms of constant dollars to nearly $997 billion. Although there were modest increases in the consumption of all major fuels and most major metals, the latter at least apparently resulted more from drawdowns of inventories than from increased production (fuel consumption increases did come from higher output levels), and consumption of most major fertilizer and chemical commodities (nitrogen, phosphate, and sulfur) were at lower levels than those in 1985. Prices for a number of mineral commodities declined, headed by the very substantial drop in world crude petroleum prices, but also including downturns for a number of metals and industrial minerals as well. There was insufficient information to reliably fix the level of the dollar value of world trade in minerals, for while output was up in the case of some large-volume materials such as iron ore, coal, and crude and refined petroleum, suggesting that the volume of trade in physical units may have increased, declining prices may well have offset quantitative gains.

Jan 1, 1988

A number of impending and actual pit wall failures have been observed and documented, which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

By Dale S. Preece

"Detonation delay timing has been an important aspect of quality rock blasting for decades. Detonators that enable delay timing have improved over the years especially with the recent advent of precision electronic detonators. The positive effects of precision delay timing have been observed repeatedly in the field with improved fragmentation, heave and overall blast control. Three-dimensional computational capabilities in terms of software, material models and computer speed have recently made possible the computer simulation of multiple blast holes in a bench configuration with precise delay timing between holes. Some of the key physical phenomena enabled by precise delay timing include: 1) collision and interaction of stress waves produced by adjacent blast holes, 2) reinforcement of stress waves from multiple holes as they reflect from the bench face and ground surface, 3) reflection of stress waves from “dynamic free surfaces” created by previously detonating holes, and 4) deformation induced fracturing, cracking and fragmentation. Simulating rock blasting in 3D has shed light on the physics involved and is resulting in an evolution of our understanding of fragmentation mechanisms. Routine use of these 3D computational tools will result in a much better understanding of the complex physics set in motion by the rock blasting process and allow predictionof improved blasting."

Jan 1, 2009

By L. A. Bakhvalov

According to the practice of mining management in the system of industrial complexes, the Kazakhstan gold mines are part of the mine processing industrial concerns providing ore-mining and ore-dressing. The cycle technology of winning operations used at the mining of vein deposits in the mines of the industrial concern is mainly provided by the systems of scrapping, scipping and electric locomotion. At present the information and computer system, elaborated on the basis of the Maikain underground mine is intended for creation of the system of automatic operation for the industrial complex mines. The information and computer system includes: - parametres characterising the accepted technology of works; - the main parametres characterising the technical devices of operation and control ; - information about the material, technical and personnel resources available at the mine; - mining and geological conditions of the deposit; - the facilities of the subsidiary units, of the mine; - the direct parametres and technico-economical indices in which the mine efficacy and activity is estimated. The suggested structure of the automatic operation system can be sensibly realized with the application of the microprocessor on the first level, the personal computer IBM PC/XT or PC/AT on the second level. For the complete realization of the project each mine will need 4-5 computers (as PC/XT), one IBM PC/AT and each mine complex - one super IBM for creation of the distributed information bank and its including in the integral world communication system.

Jan 1, 1992

By Sam G. Demou

Drag bit cutting tests were conducted chiefly to determine bit forces encountered in rock types representing a range of compressive strength and hardness and thus enable the design engineer to estimate a continuous miner's performance in a range of rock types. Testing was carried out on the Bureau of Mines uniquely designed, instrumented rock cutting device (RCD). This device can make 3-ft-long cuts at various depths and speeds to approximate full-scale drag bit cutting by continuous miners. Point attack and cutter bits were tested on four rock types ranging in compressive strength from 7,200 psi (trona) to 29,600 psi (Valders white rock). Cutting tests were made at depths up to 1 in and speeds up to 70 in/sec. Data included normal and cutting forces, groove depth, groove width, and weight of rock broken. The effect of varying the cutting speed was determined, and specific energies were calculated for the various conditions. The bit wear was also observed. For the rocks tested, compressive strength and hardness are good indicators of forces, specific energy, and wear encountered. Results, especially bit wear observations, show the possibility of extending continuous miners, already being used in trona, to Indiana limestone (10,000 psi). Rapid bit deterioration precludes use in Tennessee marble (16,800 psi) and Valders white rock (29,600 psi).

Jan 1, 1983

By Henry P. Wheeler

As recently as 1915, helium was available only in very small quantities at a cost equivalent to $2,500 per cubic foot. It was a laboratory curiocity, and its properties were of interest to a limited number of scientists (11).3/ During the past 30 years, however, helium has grown from a plaything of scientists to a factor of importance in the prosecution of the recent war. Navy blimps filled with nonflammable helium proved to be more than a match for German submarines operating in the Atlantic. American bombers were able to fly unheard-of distances to drop bombs on Tokyo, Nagoya, Yokahama, and other Japanese cities because they had been made lighter with magnesium, arc-welded in a helium atmosphere. The Army utilized helium-filled radio-sonde balloons to obtain vital information concerning weather conditions affecting D-day invasions and other military maneuvers.

Jan 1, 1946

By H. P. Jacobi

"The last 25 years have seen tremendous economic pressure placed upon the base metal processor. Industry has responded with technological innovations that have contributed to significant reductions in capital and operating costs. Major changes in processing machinery and philosophy are highlighted for the main unit operations of a base metal mill. Changes in our attitudes on what is environmentally acceptable are also discussed.INTRODUCTIONNewton's law of motion paraphrased states that nothing will change unless there is a pressure to do so.Aase metal processing as a primary commodity related industry has been under severe economic pressure over the last 25 years. This has been brought on by over capacity from new operations in the L.D.C. 's, through material substitution in a host of traditional base metal applications and generally reduced world-wide economic activity. In addition to shrinking markets our collective environmental consciousness has raised effluent standards and workplace hygiene and the employee's as well as government's economic expectations of how much ought to be derived from ''nature's riches''.Industry has responded with technological changes which, it was hoped, would counteract the cost squeeze in which it found itself.I would like to briefly enumerate the major changes, as I see them, that have taken place in the main unit operations that form the normal processing chain for base metals.While the following paper will mention several brands of products, I would like to emphasize that these are the ones that I am most familiar with and is not to say that they are the only manufacturers which have contributed to changes. In fact it ls fair to say that all makers of mining and processing equipment have made improvements to their products, to a greater or lesser degree; they have had to, to still he in business in 1986."

Jan 1, 1987

By J. A. McCamley

Gypsum scrap generated from wallboard manufacturing, construction and deconstruction activities in North America, Europe and Japan is a recognized environmental problem. Landfill disposal of this gypsum scrap is problematic, with deposits often creating hydrogen sulphide emissions and metallic sulphide groundwater leachates. Of these regions, Europe is the most advanced in dealing with the issue having enacted legislation, which will come into effect in July 2005 that will strongly encourage gypsum recycling throughout the EU. An estimated 10% to 17% of all gypsum used in the wallboard industry becomes recyclable scrap, which represents approximately 1% of the total waste stream in North America. In the United States, 2.5 to 4.5 Mt of gypsum scrap is generated each year; the volume is similar in Europe (the percentage of total tonnage is less because of the higher use of brick and concrete). The Greater Vancouver region of British Columbia has banned gypsum from its landfills, and as a result, all gypsum scrap is now recycled. New West Gypsum Recycling, a Canadian firm, uses its proprietary technology to process large quantities of gypsum scrap that is reincorporated into new wallboard, at percentages ranging up to 25%. The operation of New West Gypsum Recycling Inc. of Langley, Vancouver is examined as a case study and recommendations are provided as to how other urban regions can implement similar gypsum scrap recycling programs.

Jan 1, 2004