Search Documents

By Roy A. Bell

A 200-foot diameter, 72-foot high petroleum storage tank was built in a hillside ravine where a portion of the site contained soft clay fill. Soil-cement piles, 40 inches in diameter and up to 38 feet long, were installed to support the tank shell and ringwall, and a portion of the tank floor by drilling into the stiff to hard underlying soils and weathered bedrock. The goal was to provide a strong enough foundation to resist the seismic tank shell loading and to minimize differential settlement of the tank shell to avoid out-of-round clearance problems between the shell and floating-roof. A cantilevered retaining wall up to 8 feet high was constructed around a portion of the tank perimeter by inserting steel H-beams into soil-cement piles. The cantilever soldier piles for the retaining wall were installed from a temporary earth embankment on the hillside directly over the top of the wall. The temporary embankment was then removed and the tank pad was cut to grade in front of the soldier piles. Some of the soil-cement piles for both the tank foundation and retaining wall could not be advanced to design depth because the drill/mixing tools could not penetrate to the required depth in the hard soils/bedrock. Smaller diameter borings (22 inches in diameter) were drilled through the centers of the short-of-design soil-cement piles to the design depth and then backfilled with concrete.

Jan 1, 1997

By L. C. Bird, N. T. L. Landgren, M. W. Mikhail

"Through funds made available in 1972 by the Nova Scotia Department of Mines and Energy (DME) and the federal Department of Regional Economic Expansion, a program was initiated to recover saleable coal from mine waste dumps adjacent to the existing Acadia wash plant in Stellarton, Nova Scotia.Following evaluation of these dumps in 1972, the Acadia wash plant was modified to treat high-ash material. The first production was recorded in late 1974. By the end of 1979, a total of 738,202 t of dump material had been processed, yielding a total of 205,212 t of thermal-quality coal.The successful Stellarton operation led to considering the possibility of recovering thermal coal from other dumps. Evaluation of the Westville dumps indicated total recoverable reserves of 1,346,617 t averaging 53.8OJo ash.Parameters for plant design were defined from the washability characteristics of the dump material and the results of a bulk test. Two options were proposed; one was to use the existing plant with some modifications, the other was to build a modular mobile plant that could be used at future dump sites in the province after Westville. At the 25% ash level, the potential recovery of coal from the dump was estimated at 41% yield (by weight) or 549,679 t."

Jan 1, 1981

In 1961, West Australian Petroleum's Eneabba No. 1 bore encountered 22 seams of coal totalling 40 ft in thickness between the depths of 6373 ft and 6441 ft. On analysis, this coal had a similar calorific value (8000-HOOO B.T.U./lb, assuming 20 per cent water) to the coal from the Collie Coalfield, Western Australia's only known area of commercially exploitable coal. Being buried to depths in excess of 6000 ft, the coal at Eneabba had developed weakly-coking properties, and thus, although much younger than the Permian coals of Collie, gave promise of being a major potential source of power for Western Australia.West Australian Petroleum undertook a programme of stratigraphic drilling and shallow test drilling to determine whether this coalhorizon persisted into the outcrop of the Lower Jurassic sediments in the Hill River district, 140 miles NNW. of Perth, and, if it was present, if the quality and quantity of the coal would warrant development of the deposits by open cutting. The coal horizon was identified in the near surface, but the poor quality of the coal and the complexity of the structure made development (in the area examined) uneconomic at the time.A strong seismic reflection in the Eneabba area occurs at the same depth as the Jurassic coals. This event originates within the upper beds of the Lower Jurassic and it is probable that the velocity contrast between the higher velocity siltstones and the very low velocity coals enhances this very strong, distinctive seismic reflection.This event can be followed on continuous seismic data over a large area of the northern Perth Basin, from 13 miles SE. of Dongara to 20 miles SW. of Coorow. It can be followed from a depth of 4000 ftnear Dongara to over 17,000 ft to the SE., so development of thisvast potential source of power will depend on the economics ofprocesses being developed for the production of power from theburning of coal seams in situ.INTRODUCTIONThe discovery of 22 seams of economically useable coaltotalling 40 ft in thickness in the Lower J urassic sedimentsof the Eneabba No. 1 bore (Fig. 1) led to the search forthese seams at economically workable depths. The Ministerfor Mines in Western Australia granted to West Australian1. Supervising Geologist, West Australian Petroleum Pty. Ltd.Manuscript received at The Institute, 25th May, 1964. and presented to the 1964Annual Conference.

Jan 1, 1964

By J. A. Every-Brown

Case studies are presented of three derelict sites in Kent and Essex that provide a good cross-section of opportunities for second-generation commercial uses of former chalk, limestone, clay and gravel workings. A 240 ha abandoned chalk quarry at Grays in Essex, now known as Chafford Hundred, is undergoing mixed development to include leisure facilities, a range of housing and commercial areas and an enhanced environment. The 120 ha of Stone Marshes now comprises the Crossways business park and the Dartford international ferry terminal. Reclamation and servicing required more work than had been anticipated and the fact that the area was within the green belt added to the delays, but Blue Circle was eventually able to provide a comprehensive development of the entire area to a high environmental standard. Stone Pit 1 landfill, at Dartford in Kent, is a former chalk quarry 40 ha in area and with an original average depth of 35 m. Landfilling commenced in 1976 and during the period 1979-1984 the site operator designed, developed and installed a gas collection and flaring system. From 1986 a gas plant supplied up to 5 000 000 therm/yr of landfill gas to a local cement works and in 1989 a 1 MW power generation scheme, later expanded to 3 MW, was commissioned. Gas is currently also supplied to a metal refining company for use in internal combustion engines

Aug 1, 1994

By F. L. Pirkle

A heavy-mineral deposit about 1.6 kilometers (I mile) in length and averaging about three meters (10 feet) in thickness is exposed approximately130 kilometers (80 miles) east of Denver, along Interstate 70, in Elbert County, Colorado near the town of Limon. The deposit is exposed in a geomorphic feature known locally as Titanium Ridge. The dominant heavy minerals, accounting for about 70% of the total heavy mineral suite by weight, are ilmenite, garnet, and zircon. The mineralized zone appears in a series of visually interpretable facies that are stacked vertically and represent subtidal, forebeach, backbeach, washover fan, and aeolian depositional environments. These paleoenvironments are analogous to depositional environments represented by a modern heavy-mineral bearing facies tract on St. Catherines Island, Georgia. Thus, Titanium Ridge provides evidence that heavy-mineral accumulation models for late Cenozoic deposits in the Georgia and Florida coastal plains are applicable to heavy-mineral deposits of the Western Interior subsurface and, by implication, the Western Interior Seaway, extending from Mexico to the Canadian Arctic.

Jan 1, 2011

By B. Schoevaerts

The ever-increasing depth of mineral extraction presents a challenging environment for hard-rock underground mines. High in situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in South African underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanized installation of a chain-link mesh as evaluation at Gold Fields' South Deep Gold mine situated some 45 km south-west of Johannesburg. A purpose-built mechanized roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been specified as success criteria by Gold Fields: ? A 30% faster installation compared to the conventional methodology ? The mesh should sustain any blast damage when applied to the blasting face ? No unravelling of the mesh when cut ? No failure of mesh under normal conditions ? Reliability of the MESHA® installation handler (availability >90% ? Compatibility of the MESHA® installation handler with AC 282 boomers. Although the energy-absorbing mesh combined with yielding rockbolts is a ground support system of choice for rockburst-prone conditions, the operational upsides recognized during the trial imply that this product can also be competitively used in less demanding ground conditions where weld mesh or shotcrete are customarily used as a primary surface support.

Jan 1, 2012

By Meghan McGrath

Third generation advance high strength steels with microstructures of acicular ferrite and retained austenite were investigated and meet mechanical property goals. A good combination of strength and ductility were achieved with duplex ferrite and austenite microstructures where cementite formation was suppressed. Transformation induced plasticity (TRIP) behavior produced rapid work hardening. The mechanical properties of two hot-rolled steels with duplex microstructures were compared and had the following compositions: (1) Fe-0.14C-13.87Mn-1.42Si-3.51Al; and (2) Fe-0.06C-14.2Mn-1.85Si-2.38Al. These steels were cast, homogenized, and hot rolled at 900ºC to obtain a refined microstructure with ultimate tensile strengths and elongations to failure of 865 MPa and 39% and 1,217 MPa and 28%, respectively. The amount of metastable austenite in both compositions decreased after tensile testing from 58% and 28% to 6% and 0%, respectively. Microstructures were characterized using optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction.

Jan 1, 2010

By K. Donahue

Clay minerals play an important role in the gravitational stability of man-made rock piles by affecting geotechnical and hydrological characteristics of the material. The Goathill North rock pile at the Questa Mine in northern New Mexico has been the focus of a multi-disciplinary study to determine the effect of weathering on rock pile stability and in particular to determine if clay minerals are forming in the rock pile due to surface weathering. The results of x-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses indicate the clay minerals found within the fine-grained soil matrix of the rock pile are of hydrothermal origins and did not detect any neoformation of clay minerals. The foremost mechanism for an increase in clay minerals within the rock pile is the physical break down of hydrothermally altered rock fragments to release hydrothermal clay minerals. The hydrothermal clay minerals within the rock pile show evidence of weathering by the dehydration of smectite from 2-water to 1-water interlayers within the clay mineral structure. This dehydration is most likely due to higher temperatures and low relative humidities in the Goathill north rock pile during surface exposure.

Jan 1, 2009

By Bob King

Jan 1, 2005

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003

The polymerisation of silica is found to interfere with thickening of leach pulps at Risdon. Hydroxyl ion and fluoride ion are catalysts for this reaction. Stability may be obtained by the presence of aluminium or ferric iron.INTRODUCTIONAt Risdon it has been a matter for satisfaction that, although the concentration, of silica in leach solutions is appreciable, it has ,given relatively little cause for anxiety.However the margin of safety is small and some intermittent difficulty in thickening leach residues during the last few years has prompted a further investigation, certain parts of which are described here since they may be of general interest.Leaching and ClassificationThe method of leaching which is practised at Risdon has been described in, two previous articles, by W. C. Snow (1936) and S. W. Ross (1949) to whiCh the reader is referred for detail. Continuous leaching is practised, the circuit solution flowing through five air agitated pachucas in series, to tlie first of which calcine is added. The circuit solution, which also enters the first pachuca, consists of spent electrolyte from, the electrolytic cells and contains 90 -gm. of free sulphuric acid per litre. About 80 per cent of the solublezinc oxide is extracted from the calcine in the first pachuca, at a pH value of 1-1 (7 gm.H2S04/1 at 55 to 60°C. In the later pachucas the leaching rate decreases sharply. The leach pulp which leaves the 'last pachuca contains an average of 17 gm. of free acid per litre, corresponding to a pH of 1.7; but, owing to variations in extraction, the end point fluctuates between 2.5 and 0·3 gm. free acid per litre (pH:> 1·5 to 2.5). The average flow through the plant is 1,250,000 gallons per day, which corresponds to a production of 300...

Jan 1, 1958

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By P. H. Morris

The profile of a delta formed by fine-grained mineral processing wastes, disposed of as aqueous slurries by subaerial deposition from a pipeline, has a significant bearing on the volume that is available for waste and water storage in a given containment structure. Earlier field data and laboratory experiments suggested that mine waste delta profiles could be predicted with high levels of accuracy using data from small-scale laboratory deposition tests. The relationships between the profiles of full-size and laboratory-model deltas were analysed using the principles of kinematic similarity and a recent theory of delta formation based on engineering hydraulics. Measured profiles of full-size and model coal-mine tailings deltas are compared and the prediction of full-size profiles discussed. It is shown that the data-derived laboratory-model deltas are insufficient to allow accurate prediction of full-size delta profiles. Initial slope data or other, equivalent data for the full-size delta are also required

Apr 1, 1996

Study on Influence that Styrene-Phosphoric has on the Surface Property of Rutile Minerals

Sep 13, 2010

By René de Batz

From 1754 to the end of 1895 the production of gold in Russia had been approximately as follows: Kilogrammes. Russia proper (Finland and the Caucasus),. .. 890 The Ural Region,........505,386 Western Siberia,........116,937 Eastern Siberia,........1,218,372 Total,.........1,841,085 of the value of more than $1,200,000,000.

Jan 1, 1899

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations. The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works. This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000

By Tetsuo Yamazaki

Metal market prices rose drastically in 2006, and most broke historical records as shown in Figs. 1-4. This increase has been basically driven by economic growth in Asian countries, especially China. The growth trend is expected to continue for several years. Then, India will follow the same growth trend. Their metal demands keep the price levels high for 20 years or more. One more additional important factor on the metal market prices is hedge funds come into the market. Japan imports all metals for domestic use from overseas. The amounts imported were 1.27 million tons in copper, 0.32 million tons in lead, 0.59 million tons in zinc, 0.20 million tons in nickel, and 1.18 million tons in manganese, respectively in 2006 (Source: http://www.jogmec.go.jp/j_resourse/index.html#03). Though mainly we import the concentrates and our domestic customer smelters take the part of metallurgical leaching, the payment necessary for purchasing the concentrates is estimated about US$ 10 billions in 2006. The payments in 2005 and in 2003 were about a half and a quarter of the 2006, respectively. Japan must have effective counter measures to reduce the future payments.

Sep 24, 2006

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974

By F. F. Peng

The raw-coal feeding system and the upward medium current flow in a dense-medium vessel (DMV) are, in addition to the residence time of particles in the separator, important factors for efficient coarse particle separation. The feed material from a raw coal screen and/or pre-wet screen merge with the major volume of circulating medium as push medium, guided by an adjustable submergence baffle plate deep fed into the separator for effective separation. The remaining volume of the circulating medium enters from the purge and drain hoppers at the bottom of the DMV. This generates a gentle upward medium current flow in the separator, which prevents dense medium stratification/settling and merges as part of the push medium. A two-dimensional, two-phase model developed using computational fluid dynamics (CFD) is used to describe the flow pattern and evaluate the function of the dip plate for understanding the mechanisms of particle separation in the separator. The particle movement in the DMV is also tracked to investigate the major operating parameters affecting the separation performance of the DMV. The simulation results of the DMV separation performance are validated by in-plant test data.

Jan 1, 2007

By A. E. Chute

The shortage of sulfur is not only continuing but appears to be worsening, attended by steadily rising prices. At the same time emphasis on air-pollution abatement is also increasing. These two factors, a rising market and the growth of environmental attention, have encouraged producers to carefully review all possible sulfur sources. As a result, production of sulfur from hydrogen sulfide occurring in petroleum is receiving greater attention than ever before. Until about a decade ago, the practice of recovering sulfur from hydrogen sulfide separated from gases (either found naturally or generated in desulfurization of liquid petroleum) was wide1y recognized but contributed little to total free-world sulfur production. However, during the past ten years, the production of sulfur from this source has increased so rapidly that it now accounts for a substantial portion of total production. This trend shows no signs of slackening, and current forecasts predict that recovered sulfur may become the dominant source of supply within ten years, exceeding mined sulfur production. This paper is intended to list sulfur sources and relationships, and to discuss the potential of producing sulfur from petroleum. The processing involved, in addition to product storage and transportation will also be discussed along with important economic aspects of sulfur recovered from hydrogen sulfide. For many years, most of the world's elemental sulfur has been produced from salt domes, predominantly by the Frasch process. During the past decade, however, another production source has developed so quickly that it is expected to surpass the Frasch production sources within a short time. This new source lies in the petroleum gases and liquids from which dramatically increasing quantities of elemental sulfur are being recovered. In the phraseology of the trade, the sulfur so obtained is know as "recovered sulfur," a term which does not, as one might expect, include sulfur recovered from other sources such as smelter gases. The growth rate of recovered sulfur compared to that of Frasch sulfur, total elemental sulfur, and total Free World sulfur in all forms is shown in Fig. 1 Since 1963, sulfur consumption has exceeded production,with the natural result that the price of sulfurhas continually increased. The posted price reported for f.o.b. Port Sulphur, La., has risen from as low as $18 per ton in 1962 to $32.50 per ton in mid-1967. With freight and other charges, delivered prices have of course run much higher, amounting to $45 or $46 per ton on the east and west coasts. In some cases, spot sales for as much as $60 have been reported. Although it is playing an ever-increasing role in the sulfur market, recovered sulfur was originally a by-product of the removal of hydrogen sulfide from natural and petroleum refinery gases. Today, however, it is often the most valuable product of a multi-product processing facility. Since there are two major sources of recovered sulfur—production and refining processes —natural gas is included with liquid petroleum for purposes of this discussion. Sulfur from these sources is produced in the form of gaseous hydrogen sulfide which is removed from a gas stream and converted to elemental sulfur. Gases in which hydrogen sulfide occurs naturally are natural gas and the gas produced from a high=pres-sure crude=oil or condensate field.

Jan 1, 1969