Search Documents

The Oregon-Idaho graben evolved after widespread tholeiitic flood basalt volcanism associated with the arrival of the plume head of the Yellowstone hotspot beneath southeastern Oregon approximately 17 - 16 Ma. The north- to north-northeast-trending, 50 km-wide graben evolved between 15.5 and 10.5 Ma during east-west extension. The graben is part of a middle Miocene back-arc rift (1100 km long) that includes the northern Nevada rift, the Baker and LaGrande grabens, and the Chief Joseph dike swarm of the Columbia River Basalt Group. The graben ceased to be a volcanotectonic depression as the cross-cutting western Snake River plain began to evolve at approximately 10.5 Ma. At about 14.3 Ma and continuing to approximately 12.6 Ma the Oregon-Idaho graben began to break up into subbasins that were bounded by intragraben fault zones. The break up was accompanied by a change to calc-alkaline volcanism that persisted within the Oregon-Idaho graben until 8.1 Ma, approximately 2.5 million years after subsidence within the graben ceased. Three intragraben fault zones have been identified and a fourth is inferred. The easternmost, the Devils Gate fault zone, coincides with the magmatic axis of the graben at approximately 14.3 Ma. By approximately 13.5 Ma the magmatic axis had shifted to the west along the Dry Creek Buttes and Wall Rock Ridge fault zones. A diffuse magmatic axis developed at approximately 12 Ma farther to the west where the fourth intragraben fault zone is inferred. In addition to serving as conduits for the ascent of basalt, basaltic andesite, rhyodacite, and rhyolite magmas, the zones focused the discharge of large geothermal systems. The intragraben fault zones display a common evolutionary pattern. The 2 to 3 km-wide zones initially control the distribution of facies in volcaniclastic sediments and the location of basalt hydrovolcanic vents. During this stage, the fault zones may have had no surface expression other than a low elevation change on a relatively low-relief landscape. As relief developed by continued deformation along the fault zones, strike-length of individual faults increased and weakly consolidated volcaniclastic sediments, silicified sediments and hot-spring sinter, and palagonite were eroded from the uplifted blocks and deposited in neighboring subbasins. It is during this stage that the large hot-spring precious-metals bearing prospects evolved. Displacements of over 150 m on a few faults within the zones and possible reversal of the sense of displacement along the zones occurred in this final stage of development. Locally, the fault zones were remobilised during the subsidence of the cross-cutting western Snake River plain. The intragraben fault zones within the Oregon-Idaho graben illustrate the relations among syntectonic volcanism and sedimentation and the evolution of geothermal systems within continental rift systems.

Jan 1, 1995

By Sherwin F. Kelly

"THE TITLE I have chosen is certainly not one of those self-explanatory ones. I shall endeavour to make its significance clear during my remarks but, in the hope of minimizing that inevitable exodus which follows a good lunch such as this, I am going to withhold the final key to its meaning until the very last sentence of this talk.Some explanation is due at the beginning, however, so for those of you unfamiliar with Spanish I will explain that casa means house, or home. The casa about which I am going to talk necessitates a wide .and generous interpretation of the word, because I am using it to indicate principally that portion of the North American continent which is the home, in the western hemisphere, of British and American ideals of justice and freedom, the dignity of the individual and his right to exercise private initiative .and engage in private enterprise. In a wider sense, I am including the entire western hemisphere, which may yet stand as the last bulwark of political and industrial democracy.As for the treasures of which I am about to speak, may I remind you that there are no• material treasures but those derived from the earth, and they are derived by one of two processes, -mining and farming. These two fundamental industries are the basis, and the sole material basis, of our welfare, our wealth, our very existence. From farming, whether it be farming of the land. or farming of the sea, we obtain the food to keep us alive, healthy and able to work."

Jan 1, 1955

By R. Haecker, S. Bajic, R. Thorpe, A. Palko, M. Kalstrom

"Historically, mineral processors have used inferential data like plant instrumentation, assays, and grind sizes to monitor the performance of their plants. The ability to monitor the minerals themselves on a daily basis has eluded all but the very largest and richest of operations. The advent of a new generation of compact, robust, and user-friendly SEM-based automated mineralogy systems looks set to accomplish this, aiming to bring daily mineral monitoring of plant performance within the reach of all mills from mid-size upwards. This paper describes the use of this machine at Greens Creek Mine, a 2.5 ktpd Ag-Au-Pb-Zn operation with a complex flotation flowsheet. During the trial, the machine provided turnaround from sample collection to reporting averaging 24-36 h for key daily samples. All equipment was located within the compact mill, and proved highly reliable despite the challenging environment. Turnaround time was fast enough for metallurgists to understand, and, where possible, respond to ore and process changes while they were still happening. The plethora of data generated was filtered to a simple report whereby mill management could quickly absorb key daily mineral-based performance indicators. This paper will describe how the data was used to understand the key drivers behind metallurgical efficiency at Greens Creek, and how metallurgists began using the information to enhance daily mill performance."

Jan 1, 2014

By Foster Fraas

The most important lithium resource in the United States is in the form of the feldspathoid mineral spodumene. This mineral has not been used to any important extent as a source of lithium salts or lithium metal, as other more easily decomposed minerals have b en available in sufficient quantity to supply the relatively small demand. The need for cheaper lithium salts for such promising new uses as air conditioning or dehumidification and of lithium feldspar for use in the glass and [ramic] trades has justified the recent work done by the Bureau of Mines on King available, through improved beneficiation and extractive processes, some of the lower grade but extensive spodumene deposits.

Jan 1, 1937

By Foster Fraas

The most important lithium resource in the United States is in the form of the feldspathoid mineral spodumene. This mineral has not been used to any important extent as a source of lithium salts or lithium metal, as other more easily decomposed minerals have been available in sufficient quantity to supply the relatively small demand. The need for cheaper lithium salts for such promising new uses as air conditioning or dehumidification and of lithium feldspar for use in the glass and [ramic] trades has justified the recent work done by the Bureau of Mines on [king] available, through improved beneficiation and extractive processes, some of the lower grade but extensive spodumene deposits.

Jan 1, 1937

By D T. Froedge

With successive generations of the Iso-Seismic System, we are acquiring more and more information about the actual behavior of blast induced ground, and airborne vibration, as it propagates through the environment. Some of the original “truths” that have been long accepted may have to be \revised.

Jan 1, 1995

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

By L. B. Hales

Image analysis for feed belts and flotation has been used for over 20 years. It has been shown to aid in the modelling and optimization of Sag Mill circuits, and any improvements in the image analysis result in improvements in the model for control. Using a laser to measure the height-profile of rocks on the conveyor has been shown to increase the accuracy of the size classification. We have developed a system using two cameras in a stereoscopic configuration to provide height-profile measurement without the added expense and safety concerns of using a laser. Additionally, we have developed a novel technique for calibration of the system, using artificial intelligence techniques to optimize the model fit by adjusting the image analysis tuning parameters to values resulting in the best classification.

Feb 27, 2013

By M P. Simpson

Forty one whole rock samples from the Gold Cross low-sulfidation epithermal Au-Ag deposit have d18O values that range from 4.4 to 9.3 per mil, with an average value of 7.0 per mil. Unaltered and weakly altered rocks have d18O values greater than eight per mil, and the orebody is surrounded by samples that are depleted in 18O. A strongly silicified sample adjacent to the Empire Vein System has a d18O value of 9.0 per mil, similar to previously reported analyses of vein quartz (7.0 to 11.7ë, average 9.4ë). This suggests that, in detail, Golden Cross may have a zone of 18O-enriched wall rocks in the core of the deposit, adjacent to the main underground veins. Although some workers have suggested that stable isotope geochemistry may provide useful information for epithermal mineral deposit exploration, at Golden Cross this is not the case. Alteration minerals, major elements and trace elements all define larger, less ambiguous halos than the zone of 18O-depleted wall rocks.

Jan 1, 2001

By A. J. Vietti

A pilot plant paste thickening campaign was conducted at the Anglo Platinum Limited Mogalakwena South Concentrator plant in South Africa in order to determine the water saving capability of P&TT technology. In the process a simple water consumption model was developed for estimating the overall water consumption of the mine. The model indicates that for the Mogalakwena tailings, significant water savings are achieved by discharging thickened tailing directly to the TSF but only at densities where free water release at the TSF is close to zero. Keywords Paste, thickened tailings, thickener, water savings, water consumption.

Jan 1, 2011

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979

By A. K. Snelgrove

Introduction ?Concerning the inland commodities, as wel to be drawen from this land (Newfoundland) there is nothing which our East and Northe.rly countries of Europe doe yeelde, but the like also may be made in (ît) as plentifully by time and industry : Namely, rosen, pitch . . . metalls, and many moe. All which the countries will aford, and the soyle is apt to yeelde ... For besides these alreadie recounted and infinite moe, the mountains generally make shew of minerall substance : Iron very common, lead, and somewhere copper. I will not auerre of richer metalls: albeit ... more then hope may be concieued thereof. " - Narrative of Captain Hayes, second-in-command to Sir Humphrey Gilbert's Expedition, IJ83 (From Hakluyt). The investigations set forth in the following pages were made in the field in Newfoundland during the summer of 1927, and later in the laboratories and library of McGill University, and in the library of the Canadian Geological Survey at Ottawa, with the purpose of collating and adding to our knowledge of the geology of an area roughly wedge-shaped in outline, and nearly nine thousand square miles in extent, stretching across the centre of the island of Newfoundland, from the southwest to the northeast coasts. To the description of this district, which contains most of the known mineral occurrences of Newfoundland, the term mineral belt is here introduced.

Jan 1, 1928

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By Luciano R. G. Santos

Keywords: biosorption, cadmium, copper, biomass, spent zeolite. The majority of the industrial activities produce some kind of solid wastes. In this work two industrial residues (spent zeolite and wood sawdust) were chemically modified to increase their heavy metals sorption capacities. Manilkara longifolia (a Brazilian plant known as parajú) sawdust was first treated with NaOH and modified with different citric acid concentrations (0.6-1.2 mol/L) at 120°C, for 90 min. Infrared spectroscopy confirmed the presence of carboxylate groups in the wood structure as result of their mixing. Similarly, spent zeolites were also submitted to a chemical treatment (NaOH) to remove carbon deposited during oil cracking and to recover its sorption capacity. Batch experiments carried out at ambient temperature showed that both materials present sorption capacity for copper and cadmium comparable to weak acid ion exchange resins. A maximum of 78 mg-Cd/g and 59.7 mg-Cu/g as well as 29.9 mg-Cd/g and 14.6 mg-Cu/g were observed for the sawdust and the zeolite, respectively. The results were modeled according to the Freundlich and Langmuir equilibrium isotherms and compared with results of other studies.

Jan 1, 2005

By C. Birch

"A ‘geologically constrained’ orebody model has long been hailed as vital for a Mineral Resource statement that is compliant with the South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code). In this paper, the requirements for geological modelling as contained in the outline for the SAMREC Code are considered, and whether the new modelling software available on the market is a ‘black box’ or is better for modelling than traditional methods of wireframe creation.Implicit geological modelling is a technique that uses a radial basis function to establish and update geological models relatively quickly and efficiently from borehole data, outcrop data, manually interpreted vertical or horizontal sections, and structural data. Assays and any coded drill-hole data, such as lithology and alteration, can be interpolated.Leapfrog Geo software is an example of this new approach to geological modelling. A case study of a short training course in geological modelling for non-geologists at the University of Witwatersrand, as part of the Higher Certificate in Mineral Resource Management, is presented. The benefits of this type of geological modelling software are considered for this type of assignment as well as for mining industry applications.The use of geological models in mine planning is reviewed and a case study is presented comparing the variations in mine plan design and financial output of 13 final-year Mine Design projects from the University of the Witwatersrand School of Mining Engineering. These designs were all based on the same geological model created in the traditional way, and yet the resultant mine designs were significantly different, with very different resulting financial outlooks for the project. This raises questions as to how significant a very detailed model in the pre-feasibility and feasibility phases of projects really is, considering the huge costs involved in gathering the required data to build a SAMREC-compliant geological model."

Jan 1, 2014

By P. L. Michael

Several evaluations were made by Modified Rhyme Test (MRT) word lists transmitted through various simulations of the Trapped-Miner Communication System being developed by the U.S. Bureau of Mines. The tests were performed in a "single blind? situation so that the evaluators would not be biased by knowing the characteristics of the system being simulated. A computer program was developed to provide a simulation of the electrical aspects of the communication system and to provide an evaluation by calculation of the articulation index (AI). The study indicates that communication through the presently proposed system will be somewhat unreliable at depths as great as 300 metre even with the system operating at maximum effeciency.

Jan 1, 1977

By A Hekmat, M Fuentes, F Armijo, R Castro, F Rodriguez

Interpreting the behaviour of granular material and simulating the gravity flow are complex processes in cave mining methods. In this paper, a new Cellular Automata based code – FlowSim – is used as a flexible tool to simulate the gravity flow and subsidence zone in block caving mines. The simulation results of the gravity flow model in a real scaled mine as well as a scaled physical model are presented in this study. In this research, FlowSim was first calibrated at a mine, based on the information obtained from smart markers. These markers were located in five points of the second block of the Esmeralda sector, at the El Teniente copper mine, Codelco, Chile. The calibration was performed with the objective of reducing the discrepancy between the extraction zone defined by markers in the mine and FlowSim outputs. Regarding the mine data, FlowSim was calibrated with the minimum error of ten per cent between real and simulated results. Then, the calibrated FlowSim model was used to simulate the flow behaviour of a scaled physical model. This model was constructed in the Block Caving Laboratory of the University of Chile to scale down the same block of the Esmeralda sector with the scale of 1:200. The FlowSim outputs show that this software enables the simulation of the gravity flow of the scaled model with less than five per cent discrepancy in grade and dilution entry to the drawpoints. According to the obtained results, this paper recommends FlowSim as an appropriate tool which can improve the design of production level in block caving and can enhance the prediction of the subsidence zone and dilution entry.CITATION:Castro, R, Hekmat, A, Fuentes, M, Armijo, F and Rodriguez, F, 2016. FlowSim – a versatile flow simulation tool to quantify extraction and design alternatives for block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 645–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Rajiv Kalra, Ji Jiangang

"This paper reviews the following aspects of the world’s largest manufactured Grinding Mill’s in terms of diameter and power, along with the world’s biggest shop assembly and trial run of the mills delivered to Sino Iron Magnetite Project in Australia.1. An overview of the basic flow sheet of the Sino Iron (Magnetite) Project located in Australia2. An overview of in-house designed CITIC Heavy Industries 12.2 m (40ft) F x 11 m(36ft) LG – 28MW AG mills including FEA and major components3. In-house manufacturing at CITIC-HIC work in Luoyang China of all major components for 6 off Ø12.2 m(40ft) AG mills and 6 off Ø7.9 m(26ft) x 13.6 m(44.6ft) LG – 2 x 7.8 MW Ball Mills4. Major aspects of design and preparation of the biggest shop trial run of Ø7.9 m(26ft) x 13.6 m(44.6ft) LG Ball Mill witnessed by international EPCM’s and clients in July 2009.5. Major aspects of one piece assembly of 1300 tonne rotating element of the Ø12.2 m(40ft) x 11 m(36ft) LG AG Mill and Ø7.9 m F (26) x 13.6 m(44.6ft) LG Ball Mill at the port of the export China and transport to Australian Port and then to site.6. An insight to unique installation methods used for Ø12.2 m(40ft) and Ø7.9 m(26ft) rotating element lifting on the mill foundation in one piece assemblies.7. CITIC Heavy Industries present capability for in house design and manufacture of Grinding Mills up to Ø13.7 m (45 ft) with 35 MW Gearless drives and Ø12.2 m(40ft) with 2 x 10 MW Geared Mill drives"

Jan 1, 2012

By Khamis Y. Haramy

This Bureau of Mines paper describes the use of the borehole shear tester (BST) In mines. Assembly and procedure sections explain how the equipment is assembled and used properly. Schematics of the BST, limitations, test hole specifications, data recording and calculations are all explained briefly, and an example of the data collecting and calculations is given to assist understanding.

Jan 1, 1981