Search Documents

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel- economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the 3 reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By John A. Kiefer

Ground fault and overcurrent protection criteria for coal mine a.c. distribution systems were examined under a Bureau of Mines funded investigation. The report begins with a literature review which discusses relaying topics including instrument transformers, ground-fault pickup methods, static relaying, and comparison of relaying techniques. A chapter on ground-fault relaying provides recommendations for maximum and minimum pickup levels as a function of maximum ground current and power system line-to-ground capacitance. Research in the area of phase overcurrent protection has resulted in a complete set of procedural recommendations for the selection and setting of overcurrent relays and current transformers, molded-case circuit breakers, and distribution system fuses in coal mine power systems. The final chapter, which discusses relay system maintenance, introduces a unique test set which was developed by KETRON and used to test the performance of relaying systems in coal mines.

Jan 1, 1980

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By Raymond M. Stateham

Infrared and displacement studies were made of an unsupported roof in Kaiser Steel Corp.'s York Canyon coal mine, Raton, N. Mex. Monitoring of the roof continued until the roof over the area was caved. Loose slabs in the roof, about 6 inches thick, were detected by means of associated thermal anomalies, using remote-sensing infrared instruments. Displacement measurements taken during the study indicate that roof movement was cyclic in nature; the cycles appear to have been related to the mine work cycle (work days to idle days).

Jan 1, 1974

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Health, safety and productivity can all be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard, called AziSA, meaning ?to inform? in isiZulu, will allow any device that complies with it to join any network that supports it. The standard is designed for South African gold and platinum mines. To be practical in a typical Bushveld platinum mine, a real-time sensor system needs to be robust, reliable and cheap: ?Sensors are equipped with power sources that will last as long as the sensor is required. In effect, sensors need to be disposable: cheap enough not to warrant repair if they break. ?Communication in the stope is wireless, to avoid there liability problems associated with wire connections. For example, wires to sensors in the face area are unlikely to survive blasting. ?To get information out of the stope, the power line to the scraper winch is used as a communications link. Unlike a separate communications link, the power line will be repaired if damaged, because of its importance to production. ?Outside the stope, communications are transferred onto the mine communication infrastructure. To succeed as a management system, the next key element is the use of software decision support tools that will analyse masses of real-time data to extract key parameters and trends for decision makers. A range of sensors has been developed, including commercial sensors that have had wireless adapters added to make them AziSA compliant, and bespoke sensors that provide low cost sensing of typical mining parameters. An important parameter in any sensor network is the location of the sensor. This has to be easy and cheap to establish, so a tool has been developed to locate sensors in the confines of a stope, using ultrasonic and radio techniques. Once sensors are installed and located, they associate their location to all data that they produce. All the data from the system are captured at surface in a flexible database that can be queried by any application that requires data of any kind. It is simple to program alerts, and for actions to be associated with alerts. The use of wireless in stope also allows for communication from surface to the stope, or from stope to stope. The first implementation of an AziSA compliant system is being installed as part of the Mine Health and Safety Council funded rockfall elimination project. The design is discussed, and a future application for a platinum mine is considered.

Jan 1, 2009

By M Lipalile, A B. Tunono, A W. Naismith

Konkola No 3 shaft experienced severe mining induced stress and time related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shafts (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, including the post-grouting of all drilled shaft tips. ? Design and construction of the scour protection for the two main pylons. ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2007

The Winton Basin is one of three Southland sub-basins. The oldest known sediments are Early Oligocene terrestrial shales, sands and lignites deposited in half grabens formed as a result of oblique extension. A marine transgression in the Oligocene deposited mid-outer shelf to upper bathyal mudstones. Shallowing of the basin and tectonic quiessence lead to limestone deposition in the Early Miocene. Regional tilting led to uplift in the north and east and deposition of terrestrial lignites and gravels across the basin and the basement high to the south.

Jan 1, 1992

By D Craw, J Pope

The Greenland Group, Westland, can be characterised with respect to environmental issues by the application of a GIS database (DAME), and specific sampling campaigns. Waters draining gold mineralised areas have a distinctive chemistry characterised by neutral pH and arsenic as a trace element. The acid neutralising capacity (ANC) from carbonates usually exceeds the maximum potential acidity (MPA) from sulphides resulting in circum-neutral pH. These waters are readily distinguishable from waters draining coal mine related areas, which commonly have low pH (~4) and low As concentrations (~0.1 ppm). In contrast, dissolved arsenic mobilised from Greenland Group historic gold mining areas is up to 2.4 ppm. This As mobilisation is controlled by the secondary As mineral, scorodite (FeAsO2+2H2O). Maximum dissolved As concentrations increase with increasing pH, corresponding to the increasing solubility of scorodite with increasing pH. Dissolved As is attenuated by dilution, precipitation of scorodite, and/or adsorption to iron oxyhydroxide (HFO). Adsorption to HFO is an important attenuation mechanism in and adjacent to many mine sites. HFO is abundant at mine sites where pyrite was abundant in fresh rock, such as where the mineralised zone is dominated by disseminated pyrite. Pyrite, and resulting HFO, are relatively rare where mineralisation occurred as well-defined quartz veins. Localised HFO occurs also where ankerite oxidises in host rocks. Arsenic output flux (ca. 25 g/day) from historic gold mine sites is commonly less than the natural background flux from mineralised rocks (>5000 g/day).

Jan 1, 2006

By H. Takamoto, M. Ichinose

"The basic objectives of mine roadways are to provide sufficient cross sections in order to meet the needs of accommodation of equipment, transport, personnel travel and ventilation. However, many roadways become damaged to the extent of needing maintenance, generally dinting, and in some cases requiring re-ripping. The damaging of a roadway is a result of several factors including geological properties of surrounding strata, method of roadway formation, support systems and so on. Among these factors, strata conditions play important effects on the stability of roadways and other mining activities. Weak rocks cause excessive roadway closures, and water softens some rocks and worsens the closure problem. In Indonesia, over 250 Mt of coal is now produced from almost surface mines. In the near future, some coal must be mined from underground. Unfortunately, the mechanical properties of coal measures rocks are not so good to open underground mines. In this paper, a scientific discussion on the effect of water on the stability of roadways is given on the basis of results obtained by means of in-situ investigation and laboratory tests both in Japan and Indonesia."

Jan 1, 2011

By James M. Harrington, A. Azra Bilgin, JoAnn Silverstein

The prevention of AMD in situ is more attractive compared to subsequent downgradient treatment alternatives that do not involve source control. AMD source control can be achieved by shifting the microbial activity in the sulfidic rock from pyrite oxidation to anaerobic heterotrophic activity. This is achieved by adding biodegradable organic carbon amendments to the sulfidic rock. This technique was applied in an abandoned mine pool with a pH of 3-3.5. Following treatment, near-neutral pH and decreased effluent heavy metal concentrations were achieved. In situ bioremediation by enhancement of bacterial iron and sulfate reduction is a promising technology for AMD prevention.

Jan 1, 2005

By Kanchan K. Sen

The North Shore Connector (NSC) project will extend the Allegheny County Port Authority?s Light Rail Transit System from downtown Pittsburgh below the Allegheny River to the North Shore via twin bore tunnels. Jet grouting, diaphragm walls, and soil mixing were selected as cost-effective technically viable ground improvement and support of excavation techniques. Jet grouting was specified to provide break-out (egress) and break-in (ingress) block sections at the tunnel boring machine (TBM) launching and receiving pits. Jet grout treatment was also used adjacent to buildings with shallow foundations and below retaining walls along the tunnel alignment. A new method for measuring jet grout column diameter based on electrical resistivity was employed on the project. New equipment was introduced in the U.S for constructing soil mix temporary support of excavation using a soil-mix technique termed Cutter Soil Mixing (CSM) due to the use of two vertical cutting wheels that have evolved from diaphragm wall trench cutter technology. The system allows for continuous water tight soil mix panel construction including steel beams. This paper highlights some applications of jet grouting and various support of excavation systems (e.g. slurry walls, cement bentonite walls and CSM walls), including new innovative techniques (e.g. Cyljet and CSM) used under the constraints of an urban environment.

Jan 1, 2010

By Syd S. Peng

Mountaintop removal (MTR) mining started in West Virginia nearly 30 years ago. This surface mining method can extract multiple coal seams as thin as a few inches in whole and minimum rock dilution in very steep mountainous terrain. MTR is highly efficient, even if coal seams are in close proximity and small in a real extent. Consequently, MTR has been widely used in the Central Appalachian coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impact on the surrounding area. During the past two years, however, the debate over MTR mining has grown quickly and has become very intense. This article describes chronologically issues raised by various parties, legal actions, impacts on mining permit applications and research projects developed to address the issues.

Jan 1, 2000

By Hibbert W. D, Lottrey A

The behaviour of coal in a process is a function of both the coal properties and the processing conditions. In the case of the Loy Yang coal deposit, extensive testing has been undertaken to determine: ò the extent, distribution and structure of the coal resource; ò the variations in properties throughout the resource; and ò evaluation of the behaviour of the coal during processing. This has involved the conduct of an extensive borehole drilling program, backed by geological modelling and material characterisation (chemical, physico-chemical and petrological). Evaluation of the behaviour of the coal during processing has ranged from theoretical modelling, laboratory-scale investigations through to pilot scale and full-scale tests. Until recently, the bulk of the work was directed at evaluating the behaviour of the coal for existing pulverised fuel (pf) firing/steam boiler technology and a high level of understanding has been developed of both the coal resource and its behaviour within these systems. More recent efforts have been directed towards the evaluation of new technologies directed towards cheaper and more efficient power generation using this coal. Loy Yang coal has been evaluated in the following technologies: ò Hydrothermal dewatering/direct coal-fired gas turbine; ò Steam fluidised bed drying; ò Solar drying/densification; ò Briquetting; and ò Gasification.

Jan 1, 1992

Effect of Grinding Media on the Flotation of Sulfide Minerals

Sep 13, 2010

By John E. Wiegand

This study will discuss the AMAX Coal Co., Penndiana Pipeline Project, which was conducted in conjunction with the following parties: AMAX Coal Industries, (U.S.B.O.M.) United States Bureau of Mines, (I.D.O.R.) Indiana Division of Reclamation, Ohio Valley Pipeline, Inc., New Mexico Tech, and ourselves, VIBRONICS, INC., Evansville, Indiana. The purpose of this study was to find a safe vibration level for active gas transmission pipelines near surface coal operations.

Jan 1, 1994

By N. F. Mescheriakov

New mechanical and pneumatic-mechanical flotation machines with axial impellers have been developed. Industrial tests show that these machines ensure lower power expenditure (on flotation) by 1.5-2.0 times as compared with reference machines (with the same or improved technological indices). Application of the newly developed axial impeller, with these advantages, is possible in any volume chambers of type OK, Dorr-Oliver, Wemko etc.

Jan 1, 1998

By Gray Mullins

This paper presents experimental results from a study to assess the interface bond between a cast-in-place concrete seal slab and prestressed concrete piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid had to be displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also investigated. Both model and full-scale tests were conducted. In the model tests, twenty eight 15 cm square prestressed sections were used with the embedment depth varied between d-2d, where d is the width of the pile. In the full-scale tests, 16 specimens were tested. The prestressed piles were 36 cm square with the embedment varied between 0.5d-2d. Four of the sixteen piles were cast with embedded gages located at the top, middle and bottom of the interface region. The results showed that loads were transferred to the piles over an effective area, not the entire embedded depth. Significant bond stresses developed even for the worst placement condition. Recommendations are made for revising current values in specifications.

Jan 1, 2013

By A. H. Swart

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths (resulting in excessive stope spans) that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hardrock mines, shallow mining operations

Jan 1, 2005

Research of 200 m3 Self-Suction Flotation Machine

Sep 13, 2010