Search Documents

By Barton J. Suchomel

Introduction Despite perennial economic turbulence, Argentina continues to push ahead with efforts to develop its fledgling hardrock mining industry. The country lacks the infrastructure and mining history of neighboring Chile, but contains vast areas of great resource potential. The eastern slope of the Andean Cordillera in west-northwest Argentina is a relatively little-explored region offering geology highly conducive to the occurrence of base and precious metals deposits. Past exploration has concentrated on locating and evaluating porphyry copper-molybdenum (Cu-Mo) type occurrences. Comparatively little attention has been given to precious metals potential. An interesting and important group of base and precious metals prospects in northwestern Argentina occurs within and adjacent to the Upper Miocene Farallon Negro volcanic complex in Catamarca province. The volcanic complex contains numerous base and precious metals vein occurrences, high gold porphyry copper prospects, and possible disseminated gold targets that have attracted relatively minor attention in the past. Various geologic aspects of the region have been reported by several workers (Llambias, 1970, 1972; Caelles et al, 1971; and Sillitoe, 1973). Regional geology The Farallon Negro volcanic complex is located within the Sierras Pampeanas morphostructural province about 200 km (125 miles) east of the main Andean Cordillera (Fig. 1). The Sierras Pampeanas is characterized by north-south-trending basin and range topography that developed during the Miocene and Pliocene. Uplifted blocks are composed mainly of lower Paleozoic metasediments and granitoid plutonic rocks unconformably overlain by Tertiary redbeds and minor carbonates. A consistent landward migration of volcanic and intrusive ac¬tivity occurred in this region of the Andes from the early Mesozoic through the mid-Tertiary. An eastward extension of magmatism during the Miocene and Pliocene resulted in the formation of the Farallon Negro volcanic center. Volcanism at Farallon Negro ini-

Jan 8, 1988

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

By H. McSorley

"I note that many of you are involved in the production of zinc, lead and copper concentrates and metal, which I am the most familiar with among the non-ferrous metals. This afternoon, I will describe briefly the responsibilities of a commercial manager within a mining/metallurgical company, the basic framework of a non-ferrous metals concentrate agreement and lastly, a brief discussion of the copper, zinc and lead concentrate and metal markets.I hope this talk will contribute to a better understanding of the business between all of us and look forward to a discussion after the presentation.First of all, I work for Noranda Sales, which is the marketing and sales agent for Noranda Minerals' three operating units: Noranda Copper, Noranda Zinc and Mining Corporation. In addition, Noranda Sales acts for other mining companies in the marketing of their raw materials and metals. Noranda Sales is responsible for procuring all raw materials for Noranda's metallurgical plants, such as the Copper Group's Forne and Gaspe smelters, as well as the sale of surplus concentrates and by-products and metal products. In addition, Noranda Sales trades metals and concentrates and owns a metal brokerage business, Rudolf Wolff, a founding member of the London Metal Exchange. It does $3 billion of business in 60 countries, exporting some 80% of Noranda Minerals' output to the world.What are the responsibilities of commercial management in resource marketing to the mine and metal producers?Resource marketing and commercial administration involves assistance in establishing exploration priorities, contributing to feasibility studies, pre-production planning, product promotion and realization of income for many properties and metallurgical plants through completion of supply and sale agreements with other companie"

Jan 1, 1988

Draft tube circulators are now widely used instead of Pachucas for suspension of slurries in large tall tanks.Precipitators in the alumina industry are an example.Draft tube/tank diameter ratio is critical. Two independent criteria are given for optimum ratio. The hydraulic and energy relationships are defined. These require an impeller of very high specific speed. For a stable and efficient system the impeller should have aerofoil blades with a pitch angle which decreases from hub to tip.The draft tube must be matched to the impeller with inlet baffles above the impeller and flow control vanes below it. Tip recirculation must be suppressed. The tank itself should have a filleted flat bottom.Such a system exhibits the behaviour of axial flow devices with the characteristic undesirable behaviour at low flow.Installed and operating power requirements depend critically on hydraulic design and to a lesser extent on speed reducer efficiency.The problems of re-suspension have been overcome by a patented slot system which also improves behaviour at low flow to permit a more economic design. A number of other practical operating considerations are also discussed.

Jan 1, 1982

By Harold J. Miller

Loading and haulage of run-of-mine ore is frequently the highest cost in underground mining operations. These costs can be significantly reduced by use of belt conveyors, a common practice in coal and similar soft miner ii mines. This is particularly true if oversize ore and rock can he eliminated prior to conveying; thus producing a demand for crushers near the production areas. Portable feeder-breakers are extensively used in conveyorized mines, but no suitable, equivalent equipment, is available to provide these benefits to hard rock mines of low to medium headroom. A hard rock crusher capable of easy movement and readily disassembled would allow use to belt conveyors and could improve the general safety and productivity of any underground ore hauling system. This report summarizes proposals and findings made in conjunction with the newly designed M-44 Low Head Portable Crusher which is believed well capable of meeting the requirements of a "portable, underground, hard rock" machine as previously defined in earlier reports. Data gathered by use of the 1/4 Scale Model of the M-44 has substantiated and verified the concept sufficiently to justify construction of a full-size machine for further testing under actual mine conditions.

Jan 1, 1978

This Bureau of Mines publication consists of an overview of the mine waste management research currently being conducted by the Bureau. The following papers, given at a Technology Transfer Workshop, emphasize the increasing importance of research related to the safety and environmental considerations of mine waste disposal In recent years. Current work related to legislation passed in the last 10 years and their subsequent standards includes the development of adequate monitoring systems, development of stability and seepage prediction and control techniques, control of runoff water, and control of leaching solutions. Selected topics are included here that cover coal mine waste disposal, embankment slope stability monitoring, flow failures of mine tailings impoundments, and controlled burnout of abandoned coal mine fires. The projects described provide a current documentation of problems being addressed.

Jan 1, 1981

By Peter B. Dowden, Robert A. Robinson

Boulders, frequently found in tunnels excavated through soils, can pose major problems for full face TBMs in terms of slowing or halting the tunnel advance, cutter damage, and abrasive wear. The paper aims to consider the problem as a whole, from the geological characteristics of boulder sites, to the appropriate physical design of theTBM, and its operation in boulder-laden soils. In addition, visualization of boulders and other subsurface obstructions by seismic methods and ground penetrating radar are reviewed. The paper will assist the construction planner in assessing the risks and preparing appropriate specifications.

Jan 1, 2001

By R Hoskings

Conceptual studies of the run of mine stockpiling and reclaiming requirements commenced in 1975. Final selection of equipment was made in 1978 and the equipment was commissioned in June, 1979. Equipment selection was made after extensive investigation and visits to existing facilities throughout the world. The equipment selected is described and compared with the alternatives. Foundations were designed to minimise cleanup effort and to ensure stability of equipment under design wind loading without storm bays. Programmable logic control enables the stacking and reclaiming facility to provide a blended feed to the coal preparation plant.

Jan 1, 1980

By Jamie Bonner, Ray Hutton, Taro Nonaka

The Nancy Creek Tunnel is a deep tunnel, designed to store and convey wastewater by diverting flows from trunk sewers currently at or near capacity in the northwest of the City of Atlanta. The tunnel, constructed in hard rock, has an overall length of 13,300 m (43,700 ft), and a finished diameter of 4.9 m (16 ft). The project is currently under construction by a joint venture of Obayashi/CJB for the City’s Department of Watershed Management. This paper describes the contractor’s techniques and equipment, as well as discussing challenges which were overcome. The project is scheduled to be complete in October 2005.

Jan 1, 2005

By Y. Q. Zhang, Y. Luo, S. S. Peng, C. T. Holland

Barrier pillars in underground coal mines could eventually be subjected to a hydraulic pressure head due to the build-up of mine water in the old workings. The pressure head could not only act as a force to destabilize the pillar but also cause seepage flow through the pillar and its surrounding strata. Excessive seepage flow could induce piping failure that in turn could accelerate the mechanical failure process of the barrier pillars. In this paper, finite element simulation approach has been employed in the evaluation of the barrier pillars. Both the stress distribution and the seepage flow pattern in and around a barrier pillar have been simulated numerically. The effects of ground stress on rock permeability to water seepage has been taken into consideration in these simulations.

Jan 1, 2001

By L. F. Contreras

In open pit mine design, it is customary for geotechnical engineers to define the appropriate slope design angles within practical limits. The conventional approach to slope angle design is based on the comparison of calculated stability indicators, such as the factor of safety (FS) and the probability of failure (PF), with generic acceptability criteria not directly related to the impacts of failure. A major drawback of this type of approach is related to the difficulty of defining meaningful acceptability criteria. An alternative methodology of pit slope design is proposed, where the economic impacts of potential slope failures are calculated and used as the elements on which to apply the acceptability criteria for design. The methodology is based on the construction of a graph, referred to as a risk map, that relates the probability of exceeding the economic impact of slope failure to the magnitude of the impact measured in monetary terms. The process includes the analysis of a selected number of representative years of the mine plan and slope sections of the pit areas to define the required inputs for the construction of the risk map. The paper discusses the concepts used in interpreting the probability of slope failure, and describes the approach followed for the estimation of the economic impacts of slope failure and the construction of the risk map. Finally, the two main uses of the risk map are discussed, including the comparison with acceptability criteria for the evaluation of a specific open pit design and the comparative analysis of open pit design options in terms of value and risk to identify optimum pit layouts.

Jan 1, 2015

The Phoenix mine on the Mararoa Reef at Norseman, Western Australia, provides an outstanding: AUstralian instance of the recurrence of payable ore beneath the bottom of an abandoned mine, and an interesting and instructive example of the development ofideas with regard to ore recurrence in a particular district. The Mararoa Reef is the most productive of several hypothermal goldquartz vains in pre-Cambrian basic volc81olics which strike northsouth and dip on the average, 45 degrees east. The Phoenix minewas abandoned at 500 ft. vertical depth after producing 342,000 tons of 9.9 dwt. recovery grade (equivalent to nearly half of the total production of the Norseman field) from a 2,500 ft.. long, horizontally disposed oreshoot, which is reported to have had an ore outcrop only 30 ft. in length.Interest in the field was revived in 1933, and by 1941 new ore mined and developed on the Mararoa Reef by Central Norseman Gold Corporation N.L. amounted to approximately 700,000 tons of 6.7 dwt. recovery grade. In the same period another oreshoot of similar size and grade was developed by Norseman Gold Mines N.L., south of the old Mararoa company's site. As shown by the plans, the ore occurs in discontinuous shoots. The intervening area of shear is poor in quartz as well as in gold. Geological work on behalf of Western Mining Corporation Ltd., and Central Norseman Gold Corporation N.L. has been in progress in the mine and in the field more or less continuously from 1913 to 1941 and again since 1946. This paper describes the successive advances in the understanding of the exploratory problem up to late 1941, to which several investigators have contributed. It is published by permission of the Board of Directors of Central Norseman Gold Corporation N.L., owners and operators of the Phoenix and other mines.Development of the Prospect.In 1933 Western Mining Corporation acquired an option over the Phoenix property and adjacent leases. H. E. McKinstryl visited the mine and recognised that the ore occurred primarily on the flatly dipping sections of the vein, as distinct from the steeply dippingsections, in a wide shear zone with reverse movement. Many of the flatly dipping fractures were seen to exhibit tension phenomena and to link one shear plane to the next below on the footwall side. The flat links carried much more quartz than the steeper shears.Later, H. J. C. Conolly, assisted by J. D. Campbell, examined the prospect and by contouring the vein with reference to an inclined...

Jan 1, 1950

As a result of the world depression and the consequent heavy fall in the price of tin, Malaya joined with other great tin producing: countries of the world in a restriction scheme that heavily restricted production from its individual mines. This condition, together with the knowledge that it was becoming more and more difficult in, Malaya to acquire further areas and so prolong the existence of a specific company's activities, induced Mr. H. G. Scott, managing director for the Siamese Tin Syndicate Ltd., to consider other possible sources of production. Mainly because of the conditions that obtained in Tasmania, he turned his attention to that country, where, not only could mining be carried on without restriction as to output, but where the incidence of the exchange position created favourable conditions for operation. The district selected for examination was that of St. Helens, on the East Coast of Tasmania, which district had behind it a long record of successful tin mining operations.PRELIMINARY OPERATIONS OF SIAMESE TIN SYNDICATE LTD. AT ST. HELENS.First of all the district was examined, and there was no lack of evidence to show that tin existed, although it was impossible to get down to quantities and values without an extensive prospecting campaign. For one thing, the physical features of the country seemed to be all wrong. There were no extensive alluvial flats such as a mining engineer...

Jan 1, 1934

By P. Lefebvre, J. Sargent, K. Major, B. Darnton

"Stillwater Mining commenced mining operations at Nye, Montana in 1987 for the recovery of platinum and palladium. Exploration identified that the J-M Reef extended for 43 km. In 1998 Stillwater Mining made the decision to develop the East Boulder mine complex, located approximately 13 miles from the Stillwater mine complex at Nye, to increase production. This paper describes the design, construction, and start-up of the East Boulder process plant.INTRODUCTIONStillwater Mining Company have been producing Platinum and Palladium from their Nye, Montana operations since 1987. The mine production from Nye had been increased in stages with mine production being delivered through several portals and one vertical shaft.The deposit is narrow veined which prevents the application of bulk mining methods and thus limits the production capabilities.In order to increase the production of platinum (Pt) and palladium (Pd) Stillwater made the decision to access the ore from the J-M Reef from the East Boulder site. The East Boulder mine site is located about 21 km (13 miles) from Nye, however as shown in Figure 1, the travel distance is closer to 188 km (114 miles). Distance, on strike, and space availability at Nye precluded the expansion of the Nye concentrator to handle the increased mining rate and supported the decision to install a new concentrator at East Boulder."

Jan 1, 2003

By David B. Paul

"ABSTRACTThe US Army Corps of Engineers (USACE) has 704 dams in their inventory and over 100,000 miles of levees with a capital value of over $150 billion. Currently, there are 319 dams that are classified as high hazard and have actionable failure modes that will require structural modifications. The most frequent actionable failure mode associated with the inventory is seepage and piping. One of the most effective engineering solutions is the installation of a cutoff to limit seepage. Currently, USACE has over $1.5 Billion of cutoff wall projects under construction and/or design. Given the magnitude of the dam and levee safety issues, USACE is developing a new Engineering Manual (EM) titled “Seepage Control Cutoffs for Dams and Levees.” This EM covers all of the methods to construct cutoff walls. USACE has partnered with the Deep Foundation Institute (DFI) in preparation of the EM to ensure that it is comprehensive and draws from the expertise of the specialty foundation engineering companies that design, manufacture, and construct seepage control cutoffs around the world. The EM contains case histories as well as a comprehensive project statistical summary and guide specification paragraphs. The goal of USACE was to make the EM a state of the art document for use by Districts.HISTORYSlurry wall construction techniques were developed in the late 1940’s in Italy by ICOS. The first use of the slurry trench method of construction in the United States was by the USACE Memphis District in September 1945, to form a partial cutoff along the Mississippi River levee on the Arkansas side of the river just below Memphis, Tennessee. The idea for the project probably evolved from the use at that time of puddle clay trench cutoffs combined with the use of drilling mud for advancing borings. A paddle wheel mixing device was constructed for making slurry from native clays. Trenches were dug to a 20-ft depth using a trenching machine and to a 35-ft depth using a dragline with a 100-ft boom and 2-cu-yd bucket. Backfill was mixed in windrows at the site from hauled-in clay gravel and native materials and pushed into the trench by a bulldozer when the length of the trench was equal to about twice the trench depth. It is amazing that after almost 70 years, the technique is still about the same as it was when first developed by the Memphis District. A soilbentonite cutoff was constructed under the Kennewick Levee adjacent to the Columbia River as part of the McNary Dam Project in Washington by the Walla Walla District in 1952 The first application of a soil-bentonite slurry trench cutoff for control of underseepage at a major earth dam was at Wanapum Dam on the Columbia River in Washington in 1959.The first cement- bentonite cutoff in the United States was constructed at the Tilden Tailings Project to store tailings from the Tilden Mine in Michigan in 1976. The first cement-bentonite cutoff constructed at a dam on a river retaining a reservoir in the United States was completed in 1978 at the Elgo Dam (formerly the San Carlos Dam) in Arizona.The USACE has designed and constructed some of the deepest and most complex cutoff walls for dams since the 1970’s. The first major concrete panel cutoff wall constructed in a dam in the United States was at Wolf Creek Dam (Nashville District) by the ICOS Corporation between 1974-77. The dam has a long history of seepage issues associated with the karst geology that comprises the foundation. In 1968, about 17 years after first being impounded, wet areas, muddy flows in the tailrace and sinkholes in the downstream toe adjacent to the switchyard occurred."

Jan 1, 2014

By Richard A. Allwes

This Bureau of Mines report presents a procedure for the design of an arch canopy for use in rehabilitating a high-roof-fall area. Only dy-namic line loading of an unbackfilled arch canopy at its crown is considered, and the procedure does not account for an asymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation depends on many variables, including in-mine conditions and the engineering properties of the structure. However, a general evaluation can be based on a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. The design procedure is based on the concept that when an arch canopy is sub-jected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure is that it gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1987

By K. J. Griffin, G. W. Rosval

"In our increasingly competitive market, attempts to improve productivity by increasing axle loads have placed more severe demands on rails. CP Rail thus requires stronger, tougher, and more wear-resistant rails from steel manufacturers. The choice of any rail steel is always a compromise between technical and economic factors. The technical assessment of a candidate rail consists of laboratory and field testing. Laboratory evaluation of rail steels cannot adequately model many service conditions and must, therefore, be supplemented by long-term field testing. The field testing conducted on CP Rail is the subject of this paper.Long-term, in-track, assessment of candidate rail steels begins with the selection and re-laying of a test curve representative of the intended service with both the candidate rail and a control rail steel (i.e. the present intermediate or premium rail standard). The wear performance of the candidate rail is evaluated, in relation to that of the control rail, using data obtained with a rail profilometer developed by the Research and Development Department of CP Rail. Qualitative observations are also periodically made to evaluate the relative susceptibilities of the two rail types to surface defect formation. Testing continues until stable metal loss patterns are achieved. Relative life predictions are then made and detailed monitoring of the test site is discontinued.CP Rail's in-track assessment program for premium rails has resulted in the establishment of a new CP Rail premium rail standard - low-alloy, head-hardened, rails have replaced high alloy rails. The wear/fatigue lives of these new premium rails exceed those of our previous standard by more than 50%, and they also exhibit excellent weldability. CP Rail will continue to evaluate new premium and intermediate strength rail products."

Jan 1, 1988

This Bureau of Mines report and its companion report (Information Circular 9143) have been prepared to assist in the preparation of prefeasibility type estimates for capital and operating costs of mining of various types of mineral occurrences using current technology. The handbook provides a convenient costing procedure based on the summation of the casts for the unit processes required in any particular mining or mineral processing operation. The costing handbook consists of a series of costing sections, each corresponding to a specific mining unit process. Contained within each section is the methodology to estimate either the capital or operating cost for that unit process. The unit process sections may be used to generate, in January 1984 dollars, costs through the use of either costing curves or formulae representing the prevailing technology. Coverage for surface mining includes dredging, quarrying, strip mining, and open pit mining. The underground mining includes individual development sections for drifting, raising, shaft sinking, stope development, various mining methods, underground mine haulage, general plant, and underground mine administrative cost. This system can be used for estimating cost data for an undeveloped deposit or for checking or verifying mining costs from a developed deposit, with a minimum amount of background information.

Jan 1, 1987

By Arturo Ressi di Cervia

The utilization of diaphragm wall construction in Hong Kong began in 1974 with the construction of the New World Center, the first diaphragm wall job built in the British Colony. That landmark job of which I am presenting a few slides and a schematic description, embodied all of the difficulties and problems which are encountered in the difficult geology of Hong Kong. A small rocky island in the South China Sea, Hong Kong provides one of the finest natural harbors in the world. It is its splendid harbor, coupled with the enterprising attitude of the Hong Kong Chinese and the laissez-fair attitude of the British government which has resulted in the explosive growth of this speck of land soon to revert to the political control of mainland China.

Jan 1, 1993

The Manto Verde mine is found in the coastal ranges of the Atacama desert, 1000 km north of Santiago, Chile . The deposit is a fault-breccia specularite-oxide copper mineralisation hosted by the Jurassic andesites of La Negra Formation. It is located in a tensional fault that joins twoparallel arms of the Atacama Fault. The mine is in feasibility study: reserves are of the order of 60 Mt at 0.9 wt per cent soluble copper; mining will be undertaken at a rate of 11 000 tpd utilising an open pit and the ore will be heap-leached with acidified sea water, with copper recovery and by SX/EW.

Jan 1, 1992