Search Documents

By Kyle Selga, Christopher J. Greet

"The Pulp Chemistry Monitor (PCM) has been installed and operated in a number of concentrators in Australasia, and has produced some very interesting results. PCM measures the pH, Eh, dissolved oxygen, temperature and oxygen demand of process streams within a concentrator continuously and in real time.In the example presented in the paper the cleaner feed pulp chemistry is measured, and related back to changes in the mineralogy as well as variations in metallurgical response. For example, a decrease in Eh and dissolved oxygen as well as an increase in the oxygen demand. These changes in the pulp chemistry appear to coincide with increases in the feed grades, probably higher pyrite grades. Further, these variations in pulp chemistry and feed mineralogy have a negative impact on the concentrate grade and recovery.The implication is that if the pulp chemistry is monitored it is possible to predict changes in the mineralogy of the system, and from this the metallurgical response. Further, the changes in pulp chemistry can be used in a control system to counter the changes in mineralogy and maintain the metallurgy.IntroductionIt has long been recognized at a fundamental level that the flotation behaviour of sulphide minerals is dependent on the pH and Eh of the system (for example: Tolun and Kitchener, 1964; Woods, 1976). However, measuring pulp chemical parameters within an operating concentrator has had limited attention. Woodcock and Jones (1970a and b) were among the first to actually collect data from operating plants. Jones and Woodcock (1984) identified some of the chemical complexities of flotation pulps, and noted that most concentrators already operate at high levels of metallurgical performance but there was still considerable scope for improvement. These gains would, in part come from more effective chemical control. In the same volume, Healy (1984) discussed metal ion hydrolysis and precipitation, redox chemistry and how the surface chemistry of sulphide minerals can be influence flotation behaviour. The impact of grinding environment on the pulp chemistry and flotation response of a complex polymetallic sulphide ore is discussed by Forssberg and Subrahmanyam (1993). Their work essentially contrasts the pulp chemical and flotation performance of pulps ground with conventional ferrous grinding media to a fully autogenous system. The data suggested that the reduction or removal of iron hydrolysis contamination from the system could have a positive influence on flotation behaviour, and perhaps the first stage of “controlling” the chemistry of the system should be in the grinding circuit. Grano et al (1995) demonstrated that the collection of pulp, solution and surface chemical data could identify weaknesses within a concentrator, and from these data develop, test and implement solutions that improved the process. Greet et al (2006) showed that the pulp chemical trends observed through primary grinding and rougher flotation circuits of most sulphide flotation concentrators are approximately the same. There are differences in the magnitude of various pulp chemical parameters (pH, Eh, dissolved oxygen, temperature and oxygen demand) as a result of variations in the feed mineralogy and processes employed. Further, it was noted the Eh shifted to more reducing values of the ten days measurements were collected, and this change could be traced to an increase in the iron sulphide content of the feed. Metallurgically, this resulted in an increase in nickel recovery through the recovery of nickeliferous iron sulphides, and a decrease in nickel concentrate grade."

Jan 1, 2016

By A. H. Shapiro

A decanter centrifuge of novel design was developed for the dewatering of fine-solids slurries having micron-range particles that form paste-like, flowable, hard-to-dewater cakes. The design combines a compound beach with a cake-flow control structure that allows expressed liquid from the cake in the dry beach region to be returned back to the liquid pool while maintaining high solids throughput. In order to provide optimal performance with various operating parameters (feed rate, centrifugal gravity, pool, differential speed, concentration of feed solids, and different slurry types), the cake-flow control is adjustable. The second part of the beach is preferably at zero angle. Tests showed that the new design allows increases in both solids dryness and solids throughput.

Jan 1, 2001

By Chris Mark

Successful longwall mining requires a stable tailgate entry. Gate entry performance is influenced by a number of geotechnical and design factors, including: - Pillar size and pillar loading; - Roof quality; - Floor quality; - Entry width; and, - Artificial support (primary and secondary). This paper describes a comprehensive, practical, design methodology, based on statistical analysis of a nationwide data base of longwall ground control experience. Geotechnical surveys were conducted at 44 U.S. longwall mines, and underground observations of site geology, entry conditions, and support design were recorded at each mine. The observations were combined with discussions with mine personnel to identify 69 longwall gate entry designs as satisfactory, unsatisfactory, or borderline. Only conventional longwall designs, in which the pillars are expected to carry the full abutment loads, were included in the data base. Designs which employed yield pillars only were excluded. The case histories were characterized using five descriptive parameters. Pillar design was described by the Analysis of Longwall Pillar Stability Factor (ALPS SF). A major new contribution is the Coal Mine Roof Rating (CMRR), a rock mass classification system that quantifies the structural competence of bolted mine roof. Other quantitative measures were developed for primary support, secondary support, and entry width. Multivariate statistical analyses indicated that in 84% of the case histories the tailgate performance could be correctly predicted using just ALPS and the CMRR. Most of the misclassified cases fell within a very narrow borderline region. The analyses also confirmed that primary support and gate entry width are essential elements in successful gate entry design. The relative importance of the floor and of secondary support could not be determined from the data. Based on these results, a simple equation was developed to guide the design of longwall pillars and gate entries: ALPS SF,, = 1.76 - 0.014 CMRR Where: ALPS SF, = ALPS SF suggested for design. Guidelines for entry width and primary support density, as related to the CMRR, are also provided.

Jan 1, 1993

By Valerio Viti

In High Pressure Die Casting a molten metal is injected through a thin gate into the cast cavity. High injection pressures and high gate velocities create atomization phenomena which can negatively affect the final quality of the cast. In order to control atomization process it is essential to understand the atomization patterns and the two-phase flowfield that exist at the gate exit. In the present work, 2D numerical simulations of the flow of molten Magnesium through a high aspect-ratio rectangular gate are performed using a water analogue for an open and closed cavity. The numerical simulations made use of VOF-type (Eulerian) physical models and Lagrangian models. Further, a sub-grid scale model was implemented that, in conjunction with VOF-type equations can efficiently predict the general atomization pattern without the need for high-resolution grids. The numerical results were compared to experimental data for validation.

Jan 1, 2006

By Guthrie. R. K., H. B. Hill

"INTRODUCTION During the early 1920's world-wide attention was attracted to a group of oil fields (Mexia, Wortham, Currie, Richard, and Powell) later known as Mexia-Powell fault-line fields in Limestone, Freestonne, and Navarro Counties, Tex. Enormous yields of high-gravity oil from the wells in these fields resulted in drilling campaigns that quickly surpassed all previous records for rapid, intensive development of productive areas. The discovery of oil in the Mexia filed in September 1921 was followed quickly by the finding of oil in the Currie field in October. In January 1923 oil was discovered in the Powell field; in February 1924 the Richland field, midway between Currie and Powell fields, was brought in; and in November 1924 oil was discovered in the Wortham field, situated between Mexia and Currie fields. Each of the fileds was developed rapidly: wells were spaced closely and had high initial production; production peaks were reached early in the producing lives of the fields; subsequent decline was rapid, and there was early and rapid encroachment of edge water.In 1927 Bureau of Mines engineers, in their investigations a engineering conditions in oil,completed a preliminary study and published a mimeographed report 4/ on underground conditions in the Wortham field, and in 1928 they reported on production and development problems in the Powell Field. 5/ field."

Aug 1, 1943

By T. M. Barczak, S. C. Tadolini

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of “topping off” the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

By B W. Riddol1s

The 1983 Energy Plan calls for an increase in North Island coal production from both underground and opencast sources from the 1982/1983 production of 843 000 tpa to approximately 3.4 Mtpa within the ten year period to March 1993. This increased production is scheduled to come from the following sources: Huntly West No 1 underground mine reaching full production of 1.26 Mtpa. Huntly East underground mine increasing production to 750 000 tpa. The proposed new Huntly West No 2 mine producing 100 000 tpa in its first year of operation û 1992. The proposed Ohinewai opencast producing 920 000 tpa for supply to the steelmaking plant at Glenbrook, replacing Weavers opencast which will be worked out in 1990. Rotowaro opencast producing at 220 000 tpa (currently being achieved). Two additional sources of supply which are not scheduled to begin production for at least ten years, and both of which have been designated for coal fired thermal power generation, are the Maramarua and Mokau coalfields. It was originally envisaged that development of both coalfields would be a combination of underground and opencast mines. The form of development is yet to be confirmed by detailed feasibility studies. The location of the Maramarua, Ohinewai (Waikare Coalfield) and Mokau deposits is shown on Figure 1. Worley Consultants Limited, in conjunction with their partners Rheinbraun Consulting GmbH (Germany) and Longworth McKenzie Pty Limited (Australia) have been involved with investigations and mining assessments for the Maramarua, Mokau and Ohinewai prospects. The Maramarua and Mokau studies form part of the New Zealand Coal Resources Survey programme of updating information to the Pre-Feasibility Mining Assessment level before proceeding to detailed feasibility studies. The Ohinewai study was commissioned directly by Mines Division to investigate the feasibility of mining coal by 1989 before reserves at Weavers opencast are depleted. This paper describes typical studies which are now being commissioned by Mines Division to investigate large-scale mining development and the effect geotechnical-conditions may have on coal recovery. The magnitude of these projects is reflected in the proposed outputs û up to2 Mtpa from individual mines û and the introduction of new continuous mining systems for both underground and opencast mines on a scale which has not previously been contemplated.

Jan 1, 1984

By P. J. Baguley

The model has been developed on the basis of the observation that the partitioning behaviour of a particle is related to its calculated terminal velocity. It utilises a theoretical calculation of the terminal velocity of each particle class. This is then correlated with the observed partition data for a plant separator using empirically-derived functions of operating conditions which take into account effects such as bath turbulence, holes in drum lifters and feed arrangements. The model successfully decouples the effects of medium density and viscosity and is appropriate for any bath-type separator. The correlation between calculated terminal velocity and actual partitioning behaviour was established and modelled using data obtained from two Wemco drums treating Fe and Mn ores. The model can be used to predict the prevailing size-by-size partition curves and the separation (product grades/recoveries) given the washability of the feed and operating conditions. Simulations are used to show that, for the treatment of Fe ore, there is a maximum medium density beyond which product grades fall and that this maximum decreases as the proportion of magnetite in the medium increases. This is attributed to the dominant effect of viscosity at higher medium solids concentrations

Jun 18, 1905

By William F. Hahn

The Bureau of Mines recognized the problems encountered in low seam mining illumination systems. It was determined that the best way of implementing an illumination system is to integrate the design during the design and fabrication of new machinery at the factory. The purpose of this program was to integrate an approved lighting system in a low seam battery powered scoop and evaluate its performance. This report documents the work performed on this program and the results obtained.

Jan 1, 1980

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

By J. Jonas, J. M. Harrington, K. Wangerud, S. D. Fundingsland, J. G. Harrington

EPA NRMRL Mine Waste Technology Program and Region VIII Superfund office are jointly conducting an in-situ technology demonstration at the Anchor Hill Pit Lake, Gilt Edge Mine Superfund site. The goal is to develop in-situ treatment cost/performance data for potential application in long-term water treatment/management at Gilt Edge and similar sites. The pit contained 77,000,000 gallons of pH 3water with elevated metals, sulfate, and nitrate. The Green World Science® patented process for in situ treatment was implemented to isolate and sequester metals; create stable long-term water quality and restore a sustainable ecosystem. COCs have decreased more than 99%, and dissolved discharge standards were attained.

Jan 1, 2004

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

When selecting a solution for improving resiliency at facilities, such as airports, utility and transit sites, there are many options to protect structures and equipment against potential flooding. Each case involves an evaluation of the several key factors such as: design flood parameters, the geography and geological conditions below the site, the facility, and the layout of buildings and equipment to be protected. Upon reviewing these conditions and conducting a cost analysis of various options, the most suitable approach to protecting a facility can be determined. This paper will compare the conditions at various New York City sites, and give detail to the solutions utilized at these sites to improve resiliency and protect each facility. Flood wall types varied as did the strategies for raising critical equipment, to meet the Federal Emergency Management Agency (FEMA) and American Society of Civil Engineers (ASCE) 7 guidelines. Due to granular soil conditions, some sites may experience soil seepage below the flood wall resulting in the need for underground cut off systems. The authors will also present detail regarding the solutions used to control seepage. Various cut off systems will be discussed such as grouting and sheeting, explaining the factors that may impact the choice of systems. Another consideration in flood resiliency is the potential for a buoyancy condition on basement slabs when localized flood barriers are employed on first floor doors and windows. The authors will discuss the potential impacts of this condition on facilities and methods to mitigate this issue. 1. INTRODUCTION New York City is an urban coastal Metropolis with varied geology and low land areas. This includes but is not limited to sandy soils at Coney Island and the John F. Kennedy Airport. Soft marshes are found near Flushing Queens and LaGuardia Airport. Heavy rains and coastal storms caused disruption to daily life and heavily affected the economy of this vibrant City. For instance, in lower Manhattan business was interrupted in the Financial District. Power outage was widespread; commuter trains and subways were stopped and put out of service. Additionally, numerous residential homes were damaged in Coastal Neighborhoods such as the Far Rockaways and Staten Island. 1.1. Superstorm Sandy Flood Statistics On October 29, 2012 Superstorm Sandy impacted numerous facilities in the New York City Metro area. The resulting damage cost New York City more than $42 billion in repair costs. $33 billion was allocated to repair housing and infrastructure, and $9 billion was allocated to protect transit systems1. One of the major issues that impacted the city in terms of its preparedness was the high flood surge. The surge surpassed the former base flood elevation and reached as high as 13.88 feet (above mean lower low water - MLLW) in Battery Park at 9:24pm that evening. Tottenville, Staten Island experienced more damage where the water was recorded at +16 (North America Vertical Datum of 1988 - NAVD88), which is equivalent to 18.7 feet above MLLW (see Fig. 1). Not only was the surge at record levels, the waves in New York Harbor were also at record level where some buoy stations recorded waves of up to 32.5 feet. The City released “A Stronger, More Resilient New York” in June 2013, a plan laid out to rebuild communities impacted by Sandy and improve the resiliency of the infrastructure and buildings in New York City. Figures below help to illustrate the extent of the inundation relative to the projects being discussed.

Jan 1, 2018

By Sam Palombo, James José Varela

"Washing can be defined as the process used to eliminate or reduce the dirt (presence of fines or slimes) of one material. It is also the basic and oldest process applied to ore preparation for further concentration. This process, in combination with commnution and screening, form the so called washing plant and in many cases produce end products. This work describes the factors that influence the performance of the washing process and main washing technologies used in the mineral processing industry.The Hydro-Clean represents, since 1998, a state of the art technology in this area and is comprised of one of the most innovative solutions developed at HAVER & BOECKER. HAVER & BOECKER design and manufacture technology for mining and related industries. Today the Hydro-Clean is manufactured and sold throughout the Haver Screening Group (HSG) which is comprised of HAVER & BOECKER Maschinenfabrik Münster, HAVER & BOECKER Latinoamericana – Brazil and W.S. Tyler Canada.The Hydro-Clean is a washing technology based on utilization of high pressure water jets. To follow we will discuss how the Hydro-Clean’s different modes of operation result in several advantages related with mine waste reduction, recovery of saleable product, lower capital costs, superior washing results, less stress for the material, a wider range of application and less maintenance cost. Aside from these positive factors, its lower operation costs related to the consumption of energy and water are presented. It is important to note that the quantities, tonnages, data and management concepts presented in the paper are accurate for the time of writing and are subject to change and modification as operations progress."

Jan 1, 2009

By Francis J. Kelly

This Bureau of Mines study was made to obtain and present facts concerning the production and marketing of rare-earth metals and thorium in the Central and Southern Rocky Mountains (Arizona, Colorado, New Mexico, Utah, and Wyoming, referred to in this report as the region) and to review the current demand for these elements in the United States. Little or no published information was available on the marketing practices for these commodities. As a result of many inquiries from industry, potential prospectors, and the general public, the various factors of resources, production (present and potential), marketing, and consumption have been investigated, and the results are set forth in this report. Material concerning occurrences and deposits is from published references detailed in the bibliography.

Jan 1, 1962

By G. G. Barbante

The oxidation behaviour of selenide matte with a substantial Cu content and low Ag differs significantly from that of high-Ag matte. Low-Ag selenide mattes display a large oxygen solubility and the upper boundary of the miscibility gap in the Ag-Cu-Se-O system is depressed to quite low Se contents. As a result, the formation of Ag metal is considerably delayed. The oxidised selenide matte, low in Se and with a relatively high oxygen content, has previously been termed oxymelt. With further oxidation, its composition enters the misciblity gap and crude Ag is formed. The sodium silicate slag captures very little of the SeO2 and the dissolved Ag2O(s) content of the slag is relatively small, with a Raoultian activity coefficient of 0.57. This value was found to be independent of the slag's Cu2O content

Jun 19, 1905

By G. van Hout, D. Rahal

Caving is a mass mining method that is normally applied to large, low grade orebodies because of its low production cost and high capacity. However, equipment breakdown and poor draw management can cause mining costs to exceed that of all other mining methods. One way to minimize the effect of disruptions in the mining cycle is to use Mixed Integer Linear Programming (MILP) for long-term scheduling. This paper describes a MILP goal program which has the dual objectives of minimizing deviation from the ideal draw profile while achieving a production target. Schedule optimization is performed using a life of mine approach in which all production periods are optimized simultaneously. The underlying assumption being that material mixing in the short-term (between monthly optimization cycles) has a minimal effect on the long-term state of the panel. Schedule optimization is carried out using six general constraint types to model and control production. The constraint types define: deviation from ideal practice, panel state, material flow conservation, production quality, material flow capacity and production control. These constraints define production targets and drive production toward the ideal profile while maintaining correct mining practice. Application of the model using production scheduling data for a De Beers kimberlite mine. It is shown how different production control constraints regulate production from individual drawpoints as well as recovery of the ideal panel profile by implementing an optimised draw schedule.

Jan 1, 2003

By Damian R. Siebert

Risk-reduction measures implemented during the design and construction of a 21-story pile-supported building adjacent to a below-grade 100-year-old sewer structure were keys to a successful foundation system. Avoiding damage to the existing sewer structure during construction activities and the future ability to access the structure post-construction were the main concerns for the utility owner. Clear communication and a deliberate design process between all parties ? utility owner, building owner, structural engineer, geotechnical engineer, architect, and contractor ? were integral to the project?s success. This collaborative process helped all parties to understand the risks, both real and perceived, and to develop mitigation measures to reduce the risks. Bringing together all parties to engage in dialogue and encouraging open communication throughout the project were paramount to its success. By implementing the joint design plan, using mutually-acceptable construction techniques, and careful monitoring, the building foundation was successfully installed and all parties? risks were averted.

Jan 1, 2011

The preeipitation of dissolved lead from a strong brine by metallic iron is a chemically controlled, first order reaction. The precipitation rate is sensitive to changes in chloride concentration and temperature. The precipitation of dissolved silver is a diffusion controlled, first order reaction. The precipitation rate is insensitive to changes in chloride concentration and temperature.INTRODUCTIONLead and silver sulphates can be extracted from electrolytic zinc plant tailings, or residues, by leaching with strong brine solutions, the lead and silver going into solution as complex chlorides. One of the methods which can then be used to recover the dissolved lead and silver is to precipitate them with metallic iron. The deposition reactions which take place are of the type Pb++ Fe - Fe++ Pb............ (a)To fit such a method of precipitation successfully into a practical flowsheet it is necessary to have some knowledge of the kinetics of the various reactions, Le. to know how the precipitation rates vary with temperature, brine and metal concentrations, and so on. Reaction rates are also needed to design suitable precipitation vessels. However, when examining the possibility of using a brine leaching process to extract the lead and silver from the residue produced at the Risdon plant of the Electrolytic Zinc Co. of Australasia, it was found that, although the use of metallic iron to recover lead and silver from the pregnant brine had been reported by Ralston (1924) and by TrumbulI, Hardiek and Lawford (1948), very little was known about the precipitation reactions. Consequently a laboratory investigation was undertaken, and this paper covers those aspects considered to be...

Jan 1, 1961

By R. D. Stewart

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 18pp., 5 refs. A seismic risk assessment method has been developed for application to rockburst prone deep-level mining sites which have sufficient seismic coverage. The technique utilises several seismic hazard parameters simultaneously and assesses the seismic risk on a daily basis according to the individual levels of these parameters. Critical levels are determined from investigation of the long-term behaviour of the parameters in relation to recorded potentially damaging seismic events. The method has been applied to a data set comprising 15 months' worth of seismic data, with encouraging results

Aug 1, 1995

The Central Andes in Peru, Chile, Bolivia, and Argentina , contain two contiguous terranes which were accreted to Gondwanaland between the end of the Devonian and the end of the Triassic. These terranes, Arequipa in the north, and Chilenia in the south, differ from each other in the timing and style of their metallogenic development. However, they contain over 90% of the Central Andean porphyry copper resource. The copper porphyries in the Arequipa terrane are Paleocene to lower Oligocene in age, whereas the Chilenia deposits are mid-upper Cretaceous and mid-upper Miocene. Porphyry copper deposits occur outside these terranes, but are all Miocene in age. Miocene porphyry-style mineralisation also exists in the Arequipa terrane, but is copper-deficient and gold-rich. The accreted terranes may have favoured porphyry and other styles of copper mineralisation because they possessed relatively thin continental crust compared to adjacent parts of the Andes. Crustal thickening which commenced at about 30 Ma in the Arequipa terrane coincided with a major change to polymetallic, precious metal mineralisation which commonly displays high sulfidation characteristics.

Jan 1, 1995