Search Documents

By M. C. Bhulose

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The purpose of this project was to identify constraints that could occur in the current sub-decline shaft at Turffontein Shaft should an increase in production take place. Particular attention was to be paid to the transportation of men and materials and to the broken rock and ventilation capacity of the shaft. This project is an in-depth evaluation of the logistic capacity of the sub-decline system at Turffontein Shaft in order to determine by how much production can be increased in this area to replace tonnages from the vertical shaft area, where ore reserves are rapidly becoming depleted.

Jan 1, 2004

By H. D. Mellom

The direction of the optic or "C" axis of a uniaxial metal crystal can be found with the metallurgical polarizing microscope by examining two planes of section on the crystal. Complete orientation of the crystal can be determined if a twin crystal is common to both surfaces of section. Examination of Uniaxial Metals in Polarized Light-Rotation of a uniaxial crystal surface, properly prepared,' shows four extinction positions 90 deg apart, provided that the surface is not close to a basal section. One of these two extinction directions corresponds with the projection of the optic axis on the surface of section. This direction can be found if the 'sign of the rotationr2 for the metal is known. To find the direction of the optic axis, the crystal is rotated on the stage 45 deg from an extinction position. With a crystal of negative sign, to produce extinction the analyser must be rotated towards the optic axial direction and vice versa. All sections, other than basal, of a uniaxial crystal have the same sign of rotation and, since there is no change in sign with wave length, white light can be used for these measurements. U the sign of the rotation is not known the presumed direction of the optic axis can be determined assuming a positive sign. A third section cut normal to the presumed optic axis will show basal extinction if the assumption is correct. It is convenient to use the edge between the two planes of section as a fiducial direction common to both surfaces. The optic axis can be related to this direction. If the above measurements are repeated on the other plane of section and the angle between the two section planes measured, stereographic projection can be used to determine the orientation of the crystal optic axis. Determination of Complete Orientation—The complete orientation of a uniaxial crystal can be determined provided that a twin crystal is common to both surfaces of section, and the twin law is known. The orientation of the twin crystal optic axis can be determined in the same way as for the main crystal

Jan 1, 1962

By A. Bascetin

One very important aspect of mining is deciding what material in a deposit is worth mining and processing, versus what material should be considered waste. This decision is summarized by the cut-off grade policy. The cut-off grade strategy for an open pit mine influences the annual cash flows and affects the net present value of a project. The optimization of cut-off grade strategy requires the knowledge of detailed operational costs, mining sequence, mining operation, processing, and product constraints, as well as the grade distribution of a given deposit defined by pit, phase, and different material types. Cut-off grade optimization algorithms have been developed in the past. The most common criteria used in cut-off grade optimization is to maximize the net present value (NPV). This paper describes the determination of a cut-off grade strategy based on Lane?s algorithm adding an optimization factor based on the generalized reduced gradient (GRG) algorithm to maximize the project?s NPV. The introduced algorithm is a windows based program developed at Virginia Tech that is based on a series of Visual Basic routines within a spreadsheet environment (Excel).The benefits of the methodology are demonstrated using a hypothetical case study. Keywords: Cut-off grade optimization, net present value maximization, generalized reduced gradient algorithm method.

Jan 1, 2007

By W. J. Dick, K. G. Kress

A pipeline syphon can be a simple and reliable alternative for water conveyance as compared to otherwise more complex pumping systems or low-level outlet conduits through earthfill dams. In a simple form, it consists of a pipeline constructed over the top of a dam or other high topographic feature, connecting a source pond to a receiving pond or channel (Fig. 1). The syphon action is initiated by removing air from the pipeline (priming) using water pumps, vacuum trucks, or simple devices that can be purchased “off-the-shelf.” Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate, or other devices. Repriming is not required even if the flow is stopped, provided the syphon was not drained. A limiting factor in considering a pipeline syphon as a design option is the maximum lift (i.e. vertical distance from source pond water level to summit of pipeline syphon) which is approximately 9 m or less, depending on pipeline syphon features and site conditions. A pipeline syphon can be quickly constructed from readily available materials including steel, concrete, polyethylene, or PVC pipe. It is particularly well suited to many of the unique conditions often encountered at mine sites. This paper identifies situations that can sometimes be best resolved using a pipeline syphon. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

Jan 1, 2005

By A. T. Yu

On March 18, 1964, the 52,000 dwt ore carrier M/S Houn Maru called at the port of Coquimbo, Chile, on its maiden voyage to take iron ore to Japan. This marked the first time a vessel of this size ever arrived at Coquimbo, and the event promises to drastically accelerate henceforth iron ore exports from Coquimbo province. This was made possible by the use of a versatile shiploading system recently installed by Cia. Minera Santa Fe. Coquimbo has no mechanized loading facilities other than six conventional 5-ton cargo cranes. Limited space on shore further complicates the stocking problems. To make the best of what is available, a meticulously organized semi-hand-loading system has been developed through the years.

Jan 5, 1964

By O. Leuangthong, M. Nowak

"The impact of high-grade data on resource estimation has been a longstanding topic of interest in the mining industry. Concerns related to possible over-estimation of resources in such cases have led many investigators to develop possible solutions to limit the influence of highgrade data. It is interesting to note that the risk associated with including high-grade data in estimation appears to be one of the most broadly appreciated concepts understood by the general public, and not only professionals in the resource modelling sector. Many consider grade capping or cutting as the primary approach to dealing with high-grade data; however, other methods and potentially better solutions have been proposed for different stages throughout the resource modelling workflow.This paper reviews the various methods that geomodellers have used to mitigate the impact of high-grade data on resource estimation. In particular, the methods are organized into three categories depending on the stage of the estimation workflow when they may be invoked: (1) domain determination; (2) grade capping; and (3) estimation methods and implementation. It will be emphasized in this paper that any treatment of high-grade data should not lead to undue lowering of the estimated grades, and that limiting the influence of high grades by grade capping should be considered as a last resort. A much better approach is related to domain design or invoking a proper estimation methodology. An example data-set from a gold deposit in Ontario, Canada is used to illustrate the impact of controlling high-grade data in each phase of a study. We note that the case study is by no means comprehensive; it is used to illustrate the place of each method and the manner in which it is possible to mitigate the impact of high-grade data at various stages in resource estimation."

Jan 1, 2015

By S. A. L. Read

"The intact rock constant, mi, is one of the three basic input parameters required for the widelyused Hoek-Brown failure criterion. Values for the constant should ideally be determined by statistical analysis of laboratory test data. In this paper the influence of the inclusion or exclusion of tensile test data on derived values is discussed. We firstly investigate the relationship between direct tensile strength (DTS) test values and Brazilian tensile strength (BTS) test values based on a literature search, finding that the correlation between the two test types is DTS = 0.9*BTS, independent of the lithology being tested. Secondly, using the shear strength database of Douglas (2002), we examine the influence of confining pressure range and the inclusion or exclusion of DTS and BTS test values on calculated values of mi.Chief amongst the influences was the exclusion of tensile data in the calculation procedure, particularly when the Hoek triaxial confining stress range requirement (?3?max = 0.5?c) was not satisfied. Based on a reasonable 1:1 relationship between R (the ratio of unconfined compressive to tensile strength), use of actual tensile data in the calculations for the Hoek brown failure criterion is considered to be a simpler and more robust approach to the use of a tensile cutoff based on empirical criteria such as that of Fairhurst (1964). We advocate the fitting a failure curve using compressive and tensile test data as the most reliable means of calculating mi, while at the same time satisfying requirements as originally advocated by Hoek relating to the appropriate triaxial confining stress range (?3?max = 0.5?c) and sufficient (>5) evenlyspread data points. In the absence of triaxial data the use of R provides a practical means of obtaining estimates of mi that are more robust than guideline values."

Jan 1, 2015

By A. C. Fieldner

"Decline of the Beehive Coke OvenTwenty years ago a favorite theme of the crusader for fuel conservation was the enormous waste of valuable by-products incurred in the manufacture of blast-furnace coke in beehive ovens. Indeed, there was good reason for arousing the national conscience to this needless' loss of an irreplaceable mineral resource. In 1910, 83 per cent of the coke production was made in beehive ovens, from which surplus gas, tar, light oil, and ammonia, aggregating in value (at 1910 prices) 40 million dollars annually, were discharged into the atmosphere.In 1929, proportions were reversed and 90 per cent of the production was made in by-product ovens. The average value of by-products obtained in the production of 1 ton of coke in 1929 was $3.60, as compared with $1.16 in 1910, although the value of a ton of coke had increased only from $3.47 to $4.80. As shown in Figure 1,1 the production of by-product coke progressed rather slowly until 1915. War needs suddenly expanded the demand for coke and the by-products benzol and toluol for the manufacture of explosives. Except during the depression of 1921, this accelerating rate of production was maintained up to 1929, largely at the expense of beehive plants. The 1929 production of 60 million tons of coke will probably remain a record-breaking figure for several years. The developments which are now in progress in long-distance transmission of rural gas and in the utilization of volatile petroleum products and refinery gases for augmenting, city gas supplies may retard an other- wise accelerating demand for coke and coke-oven gas for domestic and industrial heating, Trends in Value of By-ProductsThe increasing value of by-products in comparison to the value of coke is shown in Figure 2. In 1913, the average value of by-product coke was $3.38, the value of the by-products per ton of coke was $1.41, and the cost of coal per ton of coke was $3,27, In 1929 not shown in figure) the value of the coke had risen to $4.80 per ton, the value of the by-products to $3.60, and the cost of coal per ton of coke to $5.07. The by-product values in were 155 per cent higher than in 1913, although the coke value had increased only 25 per And the cost of the coal 55 per cent. Actually the increase or the total value of coke plus by-products in this period was very little more than the increase in the coat of the coal, being 55per cent for coal and 60 per cent for coke plus by-products."

Mar 1, 1931

By S. S. Peng, C. T. Holland

Mountain Top Removal (MTR) mining started in West Virginia nearly thirty years ago. This surface mining method can extract multiple coal seams as thin as a few inches thick with total recovery and minimum rock dilution in very steep mountainous terrain. It is highly efficient even if coal seams are in close proximity and small in aerial extent. Consequently, MTR has been widely used in the Central Appalachian Coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) for the past thirty years with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impacts on the surroundings in the history of MTR mining. However, in the past two years the debate over the MTR mining has grown quickly and in times become very intensely. This paper describes chronologically the issues raised by various parties, legal actions, its impacts on mining permit application and research projects developed to address the issues.

Jan 1, 2000

By A. R. Barnes, A. F. Newall

Keywords: Pyrometallurgy, furnace, smelting, spinel, PGM, phase diagrams As Merensky reef ores are replaced by UG2 ores, chromium levels in PGM smelting furnace feeds have steadily increased. Increased chromium levels lead to operating problems. Attempts to increase the chromium solubility in the slag by a variety of techniques create other difficulties. The authors have developed a technique for removal of the chromium spinel interface along with the matte for subsequent separation outside the smelting furnace by utilising differential solidification in the ladle. The process has been patented internationally with support from the Innovation Fund.

Jan 1, 2006

By Yuanwci Shi

This paper discusses the results of research on the interaction between roof strata and shield supports including the active and passive supporting functions of the shield supports which prevents roof strata separation; pressure distribution on the canopy and under the base plate as measured in the laboratory and underground; comparison between various shield structures regarding their effectiveness on roof and floor control; and determination of optimum support capacity under given geological and mining conditions including hard-tocave roof

Jan 1, 1997

By J. Kulas, J. Weaver, K. Hagley

An assessment of potential groundwater movement beneath the tailing impoundment at the Red Dog Mine was performed, and has indicated a unique aquifer situation within sub-permafrost groundwater at the site. The aquifer was shown to be isolated from both vertical recharge and a real discharge, and is characterized as a virtually no-flow system. The permafrost resulted in a deep aquifer with high tidal efficiency, meaning that variable surface loads are easily transmitted to the fluid. The tidal efficiency has been characterized through analysis of water level fluctuations that respond to earth tides, barometric pressure loads, and loading from the pond.

Jan 1, 2002

By Dodd SF

Valuation of mining companies and their underlying assets prepared by brokers' analysts are, by necessity, approximations. The reliability of the valuations is entirely proportional to the quality of available data, the reliability of forecasts and the nature of underlying commodity price assumptions. The latter is perhaps the greatest single cause of gross variations in company and asset earnings estimates and- valuations. Assumptions are often necessary regarding commodity price achievement based on commodity hedge positions. Public disclosure from listed companies provides a sound base from which to project earnings, cashflows and balance sheets. The uncommon disclosure of projected production and cost schedules often reduces the reliability of future estimates. The application of reserve and resource estimates is contentious with practitioners applying differing weightings to importance of resources in estimating mine lives (and therefore cashflow streams). Valuation methods applied in equity markets usually focus on relative value and the identification of pricing anomalies. The commonest ""rules of thumb"" applied in the valuation of mining companies (and therefore their underlying assets) is with the use of year specific price/earnings (P/E) and price/cashflow (P/CF) ratios, with low multiples suggesting undervalued assets, high multiples overvalued situations (but these rules can often be clouded by market expectations of underlying commodity price movements). Another simply applied valuation tool is to examine the examine the value placed on reserves and resources by the market. Inexpensive gold in the ground (expressed as $ of market capitalisation per ounce of reserves or resources) might indicate a buying opportunity, but the market does discount the value of gold in the ground prior to mine development and where development risk is perceived.

Jan 1, 1994

By N A. Sikwa, L M. van Niekerk, G N. Ndlovu

In June 2012, Lucara Diamond Corporation officially commissioned its Karowe Diamond Mine in Letlhakane, Botswana. The processing plant circuit incorporates variable speed autogeneous milling, a first for African diamond processing - only previously practiced in Russia. The paper discusses the basis for the selection of milling against the more traditional circuits incorporating crushing and scrubbing. It covers early commissioning challenges of operating a mill in an æalien environmentÆ with no immediate reference plant to look up to for bench-marking.The paper describes how these challenges were overcome and learnings quickly incorporated into the mill operating philosophy for maximum diamond liberation and minimum product damage. The plant was commissioned in three months and by August 2012 the production ramp up had reached name-plate capacity. The feed to the mill has varied from highly weathered material to extremely hard kimberlite and the operating philosophy had to be optimised for the full range of ore types. While more work is required to stretch the mill operating envelope coupled with other circuit additions to improve liberation of fine diamonds at minimum capital expenditure, the mill has, to date, performed to its billing.CITATION:van Niekerk, L M, Ndlovu, G N and Sikwa, N A, 2013. Commissioning and operating an autogeneous mill at Karowe Diamond Mine, in Proceedings MetPlant 2013 , pp 215-228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

Misiman society is matrilineal and despite relatively long contact with Europeans and mining, it retains its traditional consensus style of decision making. Many Misimans at least understand English, and this has encouraged comfortable communication between the people and the company (Misima Mines Pty Limited). Company care in monitoring the environment (mostly using Misiman staff), its policy of maintaining a largely Misiman workforce, and its emphasis on training and safety, have all created an environment compatible with Misiman society. In addition, the company has constructed and/or upgraded community facilities such as the airstrip, roads, the health centre, police station and schools, and has actively promoted local business endeavours. All these initiatives have been accomplished by constant dialogue with the largely Misiman workforce, and with the Misiman people, both before and during implementation. Constant, careful communication, using traditional Misiman consensus methods, appears to be the key to continued community acceptance of the project.

Jan 1, 1991

By G. L. Oldwright, F. K. Shelton, W. E. Keck

"INTRODUCTION Zinc must be of high grade to satisfy the present demand. Even when the amount of premium paid is small, the purer metal as the buyers' preference. The following specifications for spelter were taken from the American Society for Testing Materials for 1927, Part I, pane 524. (The specifications for 1930, p. 582, are tile same.)Another specification for zinc of a much higher grade than any of the above has been established lately by the same society. The committee on zinc die-casting (Proc. Am. Soc. Test. Mat., vol. 31, 1931, p. 263) reached the following, conclusions: I. ""That the purest of zinc is necessary to produce stable zinc-base die castings, and as a result requested specifications for zinc spelter .with total impurities not over 0.02 percent."" Their tests showed that the die castings made of the purest zinc had the least elongation and the greatest tensile strength, and exhibited the least changes with temperature.Still more far-reaching claims are made for the properties of zinc containing over 99.99 percent metal. Zinc foil, for instance, may someday be made as a common commercial product. It would seem likely that the demand for zinc of high grades rill continue and that even purer varieties may be desired. This demand fits in with the modern trend in manufacturing plants of reducing the number of variables to a minimum by using pure materials, and of controlling the processing of metals during their various stages of fabrication by mechanical means instead of by expert laborers."

Jun 1, 1933

Continuing with the effort of providing new and more effective exploration methods to the mining industry, where direct methods (drilling, cross-cutting, etc.) are not applicable, either for logistical or environmental reasons or because they are costly and sometimes ineffective, we present here a new seismic technique based on full wave recording of 3-D channel waves generated within the coal seam across a longwall. In the past two years we reported the application on In-Seam High Resolution Seismic Reflection (ISHRSR) and In-Seam Seismic Tomography (ISST) to map non-coal inclusions that disrupt the coal seam continuity. In the present paper we present a 3-D In-Seam Seismic Tomography (3-DTSST) method using 3-D channel waves recorded by three component high resolution geophones. The method allows to distinguish longitudinal and transversal components of the channel waves, similar to the spheroidal and toroidal modes for the free oscillations of the earth. The recording of these waves allows a more complete analysis of the free modal vibrations of channel waves, permitting a more complete inversion of the structure of the coal seam through which they travel. The full wave analysis provides additional insights of the detailed coal structure for larger, distances than for the ones previously reported using the one dimensional method. The refinement of the inversion software is also a contribution towards the better definition of the coal seam geometry and structures disturbing them such as sandstone channels, sandstone rolls, partings, mine voids, faults, fractures, etc. The method is illustrated with three case studies where subsequent mining revealed the virtues and limitations. The first example deals with the problem of mapping mine works in one side of a longwall panel which geometry is well known, to verify its applicability to map old mine works. The second example deals with a sandstone body that partially scoured the coal seam withing a longwall panel. The third shows an application of the method to map roof conditions in a longwall panel where this problem critically affected production scheduling and costs

Jan 1, 1996

By R L. Brathwaite

As part of an investigation of the deep structure of the Waihi Basin, an extensive set of resistivity measurements was recently collected by DSIR Geology & Geophysics. The objective of this work is to map deep resistivity changes throughout the Waihi area in order to contribute to a better understanding of the regional geophysical structure. This research is also aimed at improving techniques for locating 'deposits of epithermal mineral resources, and helping to establish their origin and genetic relationship to fossil geothermal systems.   The results indicate that the basin south of Waihi is underlain by an extensive layer of low resistivity, modelled as a 5ohm-m layer several hundred metres thick. Lake sediments (mudstones), as exposed in the south western part of the basin, near Waitawheta, are the most likely source of this low resistivity layer, although hydrothermally altered clays and/or elevated temperatures are other possible causes. Strong northeast trending anisotropy is also observed, implying structural links from Waitawheta through to Golden Valley. The observed resistivity pattern is consistent with a æburied calderaÆ or æfaulted depressionÆ structural model for the basin, as inferred from gravity and magnetic data.

Jan 1, 1991

By Maral Papazian Bedian

Construction contracts in the USA contain the clause "Value Engineering" ? an interesting and curious clause allowing contractor initiated design changes. Misleading is the interpretation of value engineering implying cost saving and sharing with the owner, and curious is the timing, just before beginning of actual construction. It is not surprising that such a clause would simply be ignored, because it involves change, often major design changes in very short time; and change is feared, moreover, it is vehemently resisted by all parties, owner, designer, contractor. The problem in the USA may lie in the divergence and separation of the two entities: Designer/Engineer and Builder/Contractor, assigned to the "one" engineering project. The priorities and incentives of these two groups are very different. The Engineer spends years, even decades, in design and prepares contract drawings often without a deep understanding of construction methods. Worse, with all the time available to him and in our era of tremendous advances in computational methods and speed, the designer turns in plans that are inexcusably exaggerated code-based design with excessive safety factors. As to the Contractor, he builds, often without appreciation of design principles or regard for design engineers. Redesign to apply a new technology or optimization of an inferior design just before construction becomes unthinkable. It is not surprising that adverse and hostile relationship between the designer and the contractor is a norm with extended disputes and claims, not to mention the cost these entail. Surprisingly, "Value Engineering" was successfully implemented in record speed on several very large projects in the metropolitan New York area. The process of change was unconventional, painful, and even comical. Four case studies are presented: two Design/Build: the 1.2 billion dollars Hudson-Bergen Light Rail Transit System in New Jersey and the 90 million dollars MTA Bus Depot in Manhattan, and two Conventional Design/Bid/Build: the 90 million dollars Queens Boulevard Bridge and the 150 million dollars Long Island Expressway.

Jan 1, 2002

The rapid advance in the adaptation of scientific knowledge to the treatment of ores, resulting in improved chemical and metallurgical processes, has enormously increased the possibility of working lodes profitably, which a few years ago were passed over as unpayable. By the discovery of chlorination, and later of "Cyanidation," by the highly improved methods of concentration, and by the rapid advance in our knowledge of smelting (for which we are greatly indebted to Americanmetallurgists), and by the gradual replacement of scientifing principles and enlightened management, for rule-of-thumb methods formerly in vogue, many large low grade bodies have been opened, and are now paying dividends, which were,twenty years ago, looked upon as hopelessly unpayable. It has been more especially in these large low grade ore bodies, that modern methods have been benefical; for small lodes must be rich to pay at all, as they cannot be worked on the same gigantic scale, but even in these a percentage of metal is saved which formerly was absolutely lost.To make these large deposits remunerative it is, however necessary to try and find the point of greatest economic advantage, to handle the ore in vast quantities, to erect huge plats to treat it, to substitute automatic appliances for hand labour as far as possible, and to combine several processes supplementary to one another, so that ore which is not amenable to one process, shall be saved, by another; and by doing...

Jan 1, 1901