Search Documents

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By C. Xiao, F. Mohamm, A. Borsoi

"Nitrogen compounds produced by cyanide destruction and/or blasting are often a cause of concern for environmental compliance and at times, for water re-use in metallurgical circuits. Natural attenuation in tailings ponds and wetlands is not always sufficient to ensure compliance and/or achievement of overall water management objectives. This paper provides a general overview of active treatment methods for nitrogen management followed by an investigation of selective adsorption combined with electro-oxidation as the potential treatment method for thiocyanate. Results from bench scale treatability study are presented. The concept of holistic assessment of nitrogen management at mine sites using Risk Adjusted Life Cycle Cost is introduced and discussed in the context of gold mining operations using sodium cyanide.INTRODUCTION Unlike metals, nitrogen compounds present in mine waters originate entirely from anthropogenic sources rather than mineral deposits. Table 1 summarizes the main sources of nitrogen compounds reporting to mine wastewater.The best management practice related to the use of ANFO involves minimizing contact between ANFO and water, control and monitoring of blasting to reduce the occurrence of misfires, and reducing the consumption of blasting reagents for a given ore body. The most common practice for the management of NaCN is the incorporation of cyanide destruction in the metallurgical flowsheet and the use of tailings impoundments and holding ponds for natural attenuation of cyanide destruction residues such as NH4-N and CNO. At most mine sites there is no active management of NO3-N and SCN in wastewater. While current practices have produced satisfactory results, new enhanced methods to manage nitrogen compounds at mines are needed due to: 1) Increased scrutiny over the adverse effects of nitrogen compounds released into the environment; 2) New effluent standards; and 3) The shift away from wet tailings towards dry stack systems resulting in diminished natural attenuation and dilution of nitrogen residues prior to effluent discharge or water re-use in mineral processing."

Jan 1, 2017

By Bruno Gemmi

The objective of the ? 200 million ($280 million) project Parma Railways Station-Urban Transformation was the reconnection of the North and South parts of the town by constructing an 80 m (250 ft) wide sunken artery passing under the four double railway tracks of the station without any impact on train traffic. The site of the project, adjacent to the Parma River, presented water seepage problems at any excavation depth. The use of conventional large diameter bored pile machinery was not allowed by the Railway Authority because equipment dimension and construction phases do not comply with train traffic safety regulations. Foundations for the bypass were thus constructed by minipiles nested into jet-grouted soil using machinery operating within the existing head room and at a safe distance from the tracks. Jet-grouting treatment reached depths of 25 to 28 m (80 to 90 ft) from tracks? grade and embedded minipile-heads were terminated at 2 to 3 m (6.6 to 10 ft) below grade. Load tests on minipiles were pushed to failure. Failure occurred at a 240 t (265 t) load without breakage of the bond between the jet grouted soil and the minipiles. A 0.93 MPa (135 psi) shear resistance ??? between minipile steel casing and the jet grouted soil was measured prior to the failure of the steel casings. Overall measured foundation settlements were well within expected values and were considered insignificant.

Jan 1, 2011

In a previous paper of this series (1) ,t it was shown that during the creep of single crystals of lead, deformation proceeded to some extent by means of slip on the octahedral plane. This was demonstrated by the formation of slip lines on the surface of the specimens. At first, a few broad bands appeared after a small amount of extension had taken place; then, as extension proceeded, more and finer lines made their appearance until the whole of the specimen surface was covered.The present paper deals with the process of deformation of the creep specimens as revealed by X-ray examination..By the use of this method, the changes taking place in the crystal structure can be observed.EXPERIMENTAL METHODThe method of preparation of the specimens, their size and the purity of the lead employed have been reported elsewhere (1). At frequent intervals, the specimens were dismantled from the test rack and X-ray back reflection photographs were taken. The specimens were so marked and set up on the X-ray machine that the same spot on the specimen surface was always examined.Copper radiation was employed, the tube voltage and current being 45 kV. and 25 m.a. respectively and the exposure time 2 hrs. The slit diameter was 1 mm.

Jan 1, 1941

By AIME AIME

The first session, held Tuesday evening, February 23, in North Sheffield Hall, was called to order by Louis V. Pirsson, Chairman of the Local Committee, who introduced Prof. Russell H. Chittenden, Dean of the Sheffield Scientific School of Yale University. Professor Chittenden, in behalf of the Governing Board, felicitated the Institute on its visit to New Haven, and cordially welcomed the members and guests to the University and the city. Dr. James Douglas, who presided at the meeting, responded in behalf of the Institute. The Secretary announced that, upon the proposal of many members, the unanimous report of the Committee on Membership, and .the unanimous recommendation of the Council, the following members had been unanimously elected by the Board of Directors Honorary Members in the American Institute of Mining Engineers Prof. Richard Beck, of Freiberg, Saxony, in recognition of his distinguished service to technical literature, and the cordial

Apr 1, 1909

By John P. Wagner

The details of a three-phase study (total time period of 12 months) entitled ?Fire Alert Systems for Metal and Non-Metal Mines,? are presented. Phase 1 consists of a state of the art survey on fire detection devices and gas sensing techniques. Phases 2 and 3 include laboratory screening and systems concepts testing on various detectors classified as products of combustion, optical view-field and contact (or thermal) types under incipient and flaming combustion conditions. Recommendations for a mine fire detection system to protect shaft, sealed off or mined out (from spontaneous combustion of sulfide containing ores and cellulosic materials), and fuel storage areas are also included. me principal problem area noted during Phase 1 study is the high expected occurrence of false alarming of products of combustion detectors (POC") subjected to normal mining operations---diesel vehicles and equipment and shot firing or blasting operations. Simultaneous gas sensing of either the ratio of CO/NOx or CO2/NOx with detection of one or more fire signatures (smoke, radiant energy, or heat sensing) is the recommended approach to discriminate against these operations.

Jan 1, 1975

By T. M. Williams, P. M. Green

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The sediment geochemistry of streams draining Southern Uplands and Lake District turbidites was compared with lithogeochemical data for the source greywackes, using stratigraphically defined catchments. Several systematic trends in element abundance variation between source and stream sediment can probably be applied more widely to interpretation of drainage geochemistry. Pb and Zr increase markedly from source rock to sediment, by adsorption on clay and zircon grain concentration. Variation of feldspar-related elements Rb, Sr, K and Ba appears to be controlled by source grain size and compositional maturity. Ni shows surprisingly little change and Fe and Co are only slightly raised. Cr is particularly useful, with variations superimposed in anomalously high regional levels. Abrupt changes in Cr distribution in stream sediment coincide with stratigraphical boundaries, allowing drainage data to be used as a surrogate for whole-rock values

Jun 19, 1905

By M. W. Grabinsky, M. S. Diederichs, E. Hoek

Provided that they are used correctly, numerical models can be of considerable assistance to mining engineers in designing underground excavations. Guidance is given to the engineer or geologist who is not a specialist in numerical analysis but who is interested in using numerical modelling tools or in employing someone to analyse the stresses, displacements and failure in the rock surrounding underground excavations. A description of the theoretical background to a number of these numerical models and discussion of the advantages and disadvantages of each are followed by guidelines on the selection of appropriate models for each stage in the development of a mine, from exploration to the completion of mining

Jan 1, 1991

By G Eastwood, C Joyce, P Ryan, G M. Johnston

Over the years, predictive techniques for Acid Mine Drainage (AMD) and the natural processes affecting acid generation have received considerable attention. Less emphasis has been placed on the sampling strategy and the integration of testwork results with the geological data base. The sampling strategy employed and the development of a geological model to determine the spatial distribution and volume of acid producing material are often crucial for developing cost-effective containment and mitigation measures. The geological model provides a link between the occurrence, timing, destination and placement of mined waste rock. Careful and accurate interrogation of a comprehensive geological database provides this linkage. The AMD testwork program at Cadia in NSW has been designed to identify the temporal selective handling requirements that will be required during operation. Sampling involved collection of representative combinations of all waste rock types identified within an extensive geological database. These samples were subjected to static, kinetic and accelerated weathering predictive tests. Preliminary results have been used to construct a waste block model for the deposit that identifies the quantity and distribution of acid producing material. Integration of the block model with the mine scheduling determines when the material will be mined.

Jan 1, 1996

By F. P. Haver

The Federal Bureau of Mines developed a 10,000-ampere cell to determine the economic feasibility of producing high-purity electrolytic titanium from mill scrap or offgrade sponge. Operating variables were investigated, matetial handling procedures were established, and the cost of electrorefining titanium was determined. The prototype cell produced premium-grade metal (<100 Brinell hardness number (B.h.n.)) from very impure Kroll sponge at a processing cost of less than $0.60 per pound. Refined metal was deposited at the cathode in the form of coarse (85 percent plus 34-mesh), hexagonal crystals of a titanium when the cell was operated an 850° C. A cathode current density of 1,000 amperes per square foot and a molten sodium chloride electrolyte containing approximately 5 percent by weight of soluble titanium were used. In continuous operation, at the optimum number of ampere-hours, (40,000), the current efficiency averaged slightly less than 60 percent. It was possible to supply large enough amounts of electric current for electrolysis to maintain the temperature of the bath, thus reducing overall power consumption to less than 5 kilowatt-hours per pound of metal refined.

Jan 1, 1961

By James W. Harrower, Gerald S. Ball

This paper discusses the installation of steel linings in vertical, raisebored openings. Design criteria used to evaluate the applicability of liner type and design are presented as well as a brief description of installation procedures. Specific projects completed by J. S. Redpath Corporation are then outlined noting special considerations and techniques.

Jan 1, 1985

By Met B

IN the followmg paper an account is given of work performed by the author for the purpose of sampling a slime dam on the leases of the North Mount Farrell Co. N.L., at Tullah, Tasmania, during the summer of 1925-26.For convenience the paper is divided into sections as follows:1. THE MINE2. THE SLIME DAM3. SURVEY OF THE DAM4. BORING OF THE DAM(a) INTRODUCTION(b) 1ST METHOD(c) 2ND METHOD(d) 3RD METHOD(e) 4TH METHOD(f) GENERAL NOTES5. CONCLUSION

Jan 1, 1928

In the 1980s and?90s the gold mining industry in South Africa came under pressure from the continued poor dollar gold price and escalating Rand based costs, furthermore the external impacts on the industry were changing. Thus, the Chamber of Mines (COM) shifted its focus away from many historical areas of support towards the new industry challenges in safety and health, labour markets, environmental responsibility, mineral rights legislation and social responsibility. During 1997 the lack of funds and the changes facing the tertiary institutions were often subjects of discussion at the various sub-committee meetings. The Metallurgical Sub-committee of the Chamber Education Fund or the Sub-committee of Consulting Metallurgists as it was known identified the need for the funding structure to change with the times. Up to this time the Chamber of Mines operated an Education Fund that supported mining industry academic departments at various South African tertiary institutions; these funds were derived exclusively from the country?s gold and coal mines the basis of Chamber membership. Funds of less than R5 million per annum were available for distribution by the three disciplinary sub-committees of mining, metallurgy and geology.

Jan 1, 2003

By J. P. McCullough

In 1943, the Federal Bureau of Mines began a program of thermodynamic investigations of petroleum constituents and related compounds. These systematic, long-range studies, which were conducted in the thermodynamics laboratory of the Bartlesville Petroleum Research Center and are still continuing, have resulted in a substantial quantity of data valuable to the petroleum industry and science in general. As separate phases of these studies were completed, the findings were promptly reported in the scientific press. During the past 16 years, 89 journal articles, giving the results obtained for individual compounds and small groups of related compounds, were published, mainly in the Journal of the American Chemical Society and the Journal of Physical Chemistry. In addition, members of the Bureau staff have contributed six chapters to specialized reference books. This circular, prepared in response to many requests, lists these 95 published papers, giving an abstract of the contents of each, as well as titles, authors, and literature citations. The journal articles are listed in the order of their preparation, which closely approximates the chronological order of their publication; hence, the item number to the left of each citation corresponds to the assigned contribution number. For the convenience of the reader, the abstract section is followed by a condensed bibliography, arranged alphabetically by senior author and keyed to the abstracts by appropriate contribution numbers in parentheses after the entry.

Jan 1, 1961

By C. Musingwini

An often overlooked factor in the analysis of mine layouts and schedules is technical operating flexibility (or tactical flexibility), mainly due to its nebulous nature. By glossing over technical operating flexibility the resultant mine layouts and schedules maybe suboptimal. The need to incorporate technical operating flexibility into the analysis and comparison of mine layouts and schedules is increasing in importance. The nature of technical operating flexibility is illustrated, previous work on valuing of operating flexibility reviewed, and a proposal made on how technical operating flexibility can be quantified for tabular reef mines by using a platinum reef deposit as a case study. Once technical operating flexibility has been quantified it becomes possible to explore its incorporation into the analysis of mine layouts and schedules and subsequent optimization processes. This paper is a revised version of a paper presented in the Proceedings of the Second International Platinum Conference, ?Platinum Surges Ahead? in 2006. The work described in this paper is part of a current PhD study at the University of the Witwatersrand. Keywords: mine plans, layouts, schedules, technical operating flexibility/tactical flexibility, ore availability.

Jan 1, 2007

Jan 1, 2003

William Kent, New York, N. Y.:—The Institute may congratulate itself on the opportunity of reading the splendid address of President Brunton. It is an admirable summary of the progress that has been made in the mining and metallurgical arts in recent years. The paper rightly gives the chief credit for this progress to the aid which has been rendered to these arts by the advances in mechanics, chemistry, and electricity. It is notable that most of the headings in Mr. Brunton&apos;s address refer to the work of the mechanical engineer, the electrical engineer, and the chemist, rather than to that of the specialist in mining-operations. It seems that the most successful mining engineer of the present day is the one who makes the most intelligent application of the inventions and designs of engineers and others who are not directly engaged in mining. A tabulation of the headings of the address, grouped as below, shows this most clearly. Work of the Mechanical Engineer—Rock-drills, hoisting-machinery, tramming, pumping, ventilation, dredging, Sampling, concentration, briquetting, fume-recovery. Work of the Electrical Engineer—Electric machinery for hoisting, pumping, tramming, lighting and signaling, electric transmission, electric smelting. Work of the Chemist and Metallurgist—Explosives, chlorina-tion, cyanidation, roasting, lead-smelting, and copper-smelting. Work of the Geologist—Economic geology. Work of the Mining Engineer—Mine-mapping, surface-mining, timbering, tunneling; and planning and supervision of the work in general. The mining engineer of the present day, who is in responsible charge of a large plant, finds his chief work not in doing those things he was trained to do as a specialist, but in making use of the knowledge of geologists, chemists, and electrical and

Jan 1, 1910

By C. C. Harris, A. Jowett, S. K. Ghosh

An equation derived from first-order kinetics and accounting for return from froth to pulp has correlated continuous flotation data. The concentration of floatable material in the pulp can be altered either by changing the feed concentration or the feed rate. The latter does not affect the flotation rate constant, the froth to pulp return constant, and the concentration of non-floatable material in both the pulp and concentrate. Both the return constant and the concentration of non-floatable material in the pulp are directly proportional to the feed concentration, while the concentration of non-floatable material in the concentrate is related to the feed concentration. The investigation of the froth flotation process by continuous test methods, previously used by Brown and smith,1 Jowett and Safvi2 and Jowett and West,3 is being continued. Recent tests, primarily concerned with flotation cell design, have yielded kinetic data suitable for testing an equation proposed by Arbiter and Harris4 which postulates that a flotation process is defined by two rate constants: 1) the rate constant for mass transfer from pulp to froth. Previous workers have regarded this as the flotation rate constant. 2) the rate constant for mass transfer from froth to pulp, which has previously been ignored. THEORY Under continuous flow conditions at the steady state in Fig. 1 the equation developed4 is Symbols are defined in Table I. The air-liquid ratio terms4 have been omitted, since they are substantially constant for a given set of conditions. Also, for a system operating at the steady state Vf and V, remain constant and Eq. 1 can be written: Cp/Cc=b&apos;/a,+Qc/a&apos; [2]

Jan 1, 1963

Utilizing a very large database from a mined-out area on a South African gold mine, the relative efficacy of a method to mitigate the smoothing effect introduced by the algorithmic constraints imposed by kriging was investigated. Smoothing effects arising from limited data availability are differentiated from the smoothing arising from the application of estimation algorithms. Very little can be done to ameliorate smoothing of estimates because of too little data, barring additional drilling or sampling. However, the smoothing effects resulting from the kriging process are shown to be mitigated by use of an alternative algorithm. The primary criterion in the development of the new algorithm was to avoid re-introducing conditional bias. This paper examines firstly the smoothing effects introduced into estimates via the kriging covariance matrix, secondly the process for ameliorating the smoothing effect, and finally it uses a case study to demonstrate the effectiveness of the new algorithm on a very large database. The database was used to introduce a 60 m by 60 m drilling pattern which in turn was used to model the semi-variogram and produce 30 m by 30 m kriged block estimates. The follow-up database was then re-introduced (roughly 5 m by 5 m grid spacing) and averaged into 30 m by 30 m blocks to provide a direct comparison with the initial estimates. In this way the extent of smoothing and accuracy of the estimates before and after the corrections was tested.

Jan 1, 2014

By R. Boom, L. Holappa

In the present paper, microstructure changes of solid-state reduction of industrial chromite pellets and lumpy ore were investigated with SEM/EPMA. To simulate the reactions in the packed bed zone of the Submerged Arc Furnace (SAF), carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at 1500 °C. Scanning electron microscopy was used to observe and analyse the structure and composition changes of the chromite samples. It was found that reduction of lumpy ore generally took place slower than that of pellet. In all samples, chromite reduction proceeded faster in the outer part of the sample than in the centre part. The reaction mechanism is discussed on the basis of experimental results and earlier investigations. The possibilities to optimize the FeCr production process are also discussed.

Jan 1, 2007