Search Documents

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

By T. E. Swigart, C. E. Beecher

The Federal Government, as the largest lessor of oil and gas lands in the United States, is vitally interested in the conservation of those resources. This manual has been prepared at the direction of the Secretary of the Interior to call the attention of lessees of public oil and gas lands to the most common oil and gas field wastes and the best methods of preventing them; to outline the policies of the Interior Department on field operations; and to give information as to how the "Operating Regulations" of the department will be interpreted by the Bureau of Mines. The oil industry has progressed steadily. Present operating methods are much more efficient-and less wasteful-than those of a few years ago; moreover, the art of producing oil and gas is continually advancing. Public interest requires that improved methods, which will result in obtaining the greatest possible amounts of oil and gas from the natural deposits, shall be developed and used. Part I of this manual points out types of oil and gas wastes and suggests, in detail or by reference, the most practical and effective methods in current practice for stopping these wastes. Throughout Part I the department's operating policy is given, with interpretations of the "Operating Regulations" for enforcing every practical measure of conservation. Part II comprises the revised "Operating Regula-tions" which supersede all previous regulations and will govern future operations on public lands; it will be found in the pocket in the back cover of this bulletin.

Jan 1, 1923

By G. J. de Korte

South Africa’s best-quality coal, located in the central Highveld basin, is becoming depleted and alternative sources of coal, such as the Waterberg coalfield, will have to be developed to supply the country with coal in the future. The quality of the coal being mined in the central basin is gradually becoming poorer. This necessitates that more of the coal be processed to improve the quality to meet customer requirements. The challenge to the coal processing industry is to process low-yielding coals to produce goodquality products and at the same time ensure that coal mining remains economically viable. This requires that more cost-effective coal processing technologies be investigated and implemented.

Jan 1, 2015

Results of laboratory studies on the flotation of marmatite (zinc sulphide) with new reagents, which were developed to avoid the use of copper sulphate, are presented.Episulphides were chosen as the basis for the reagents because of their reported special chemical affinity for zinc and cadmium. Attempts were made to solubilize and introduce functional groups to episulphides with organic and inorganic acids, ammonia, phenol, aniline, diethylamine, and pyridine. As a class of reagents, the episulphide-amine combination was generally found effective in zinc sulphide flotation to a greater or lesser degree. Best results were obtained with ethylene sulphide-aniline combination. Although anilino-ethyl mercaptan is the reported reaction product of aniline and ethylene sulphide, it was concluded that the effective zinc sulphide flotation with ethylene sulphide-aniline combination is not entirely due to the formation of the mercaptan.The economics of the possible usage of ethylene sulphide-aniline reagent are discussed.

Jan 1, 1974

By J. R. Heberger

"“Safety Pays in Mining” web application developed by the U.S. National Institute for Occupational Safety and Health Mining Program, helps mines determine the potential costs associated with mining injuries. This web app groups injuries by type, either by the cause of the injury or by the nature of the injury. When the user selects one of more than 30 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, the app will estimate the total costs of the selected injuries, including an estimate of additional indirect costs, the estimated impact of total injury costs on mining company profits, and provide some examples of other items, such as services or equipment, on which companies could spend the savings that result from the prevention of injuries. This paper reviews the app by discussing its development, how it is used to show the true costs of mining injuries, and how mines can benefit from using it.IntroductionInjuries on the job cause pain and suffering. They can also profoundly affect profits and daily operations. In addition to paying direct costs or increased premiums for workers’ compensation insurance, a company might need to pay overtime for other workers to fill an injured worker’s job role, cover training costs for a replacement worker or divert administrative resources in the wake of an injury. “Safety Pays in Mining” is a web app that estimates the distribution of these injury costs and assesses the impact that occupational injuries have on a company’s profits.The costs of specific types of occupational injuries in mining are not readily available as mining and insurance companies do not usually share this information. As a consequence, companies only have cost information based on previous experience with their own employees. Therefore, if a mine never experienced a finger amputation for one of its miners, for example, it would not be aware of the possible costs associated with this type of injury. In addition, injury costs are unique in that the cost distribution is so wide that just using the average cost of a specific injury type does not provide adequate information. Some injuries involve immensely high costs, and even though the risk of these high-cost injuries occurring is low, mines need to be aware of the potential impact on their company’s financial health."

Dec 1, 2018

By J. P. F. Charpin

The transport of large boulders in a furrow from a mining area to a nearby pond was considered. The furrow is filled with a mixture of water and soil particles flowing down to the pond at high velocity. Due to operating constraints, the slope of the furrow is reduced progressively. A relationship is derived, relating the slope of the furrow and the composition of the fluid to the maximum size and shape of the transported boulders. The characteristics of the boulders carried all the way down to the pond may then be determined.

Jan 1, 2007

By Prosser A. P

The conditions under which vanadium is rendered insoluble by silica in the alkali-roast process have been investigated starting with both slag and reagent-grade materials. The inert phase is a glass formed slowlyfrom soluble NaV03 produced at lower temperatures. It contains approximately 30 per cent V in a partly reduced state; iron is not a principal component. Some of the vanadium in the inert phase is slowly returned to a soluble form by heating in an oxidizing atmosphere below the temperature at which the glass is formed (750°C). As the reaction leading to the required, soluble form of vanadium is also slow between 600 and 750° optimization and control of the temperature profile and atmosphere in the furnace, and the residence time of the solids, are necessary to ensure high vanadium extraction during subsequent leaching.

Jan 1, 1976

By A. E. Anderson, H. J. Hilll

Laboratory data for 155 field muds and 77 .shales have been used to develop correlations to estimate the net streaming potential component of the SP. Analysis of these data and comparison with field tests show that streaming potential corrections must be made to obtain an accurate estimate of the electrochemical potential for use in the determinntion of formation water resi-iiviy. The self-potential curve is related to formation water resistivity, and considerable effort within the oil industry has been directed toward clarifying this relationship. The Schlumbergers and Leonardon1,2 recognized that two types of potentials, electrochemical and electro-kinetic, resulted in the net potential variation in the borehole. Most of the later papers have dealt with the electrochemical component and its controlling parameters. The investigations of Wyllie,2" Salisch' and Moore5 provide the most extensive sources of data on streaming potentials across mud cakes. These authors observed streaming potentials of sufficient magnitude to be of critical importance in SP interpretation, if it is assumed that streaming potentials develop only opposite permeable beds. Streaming potentials across shales have been reported by Schenck and by Gondouin, et al.7 Since SP magnitude is the difference in potential opposite shale and sand beds, these authors suggested that the net streaming potential component may be negligible. The present investigation was initiated to evaluate empirically some of the parameters controlling the magnitude of the net borehole streaming potential and to determine whether useful relations between mud properties and net streaming potential could be established. Field muds were used in this investigation. These muds were characterized by the amount and type of chemical treatment utilized for five days before Sampling. Filter loss, mud resistivity, mud density and filtrate resistivity were determined for each mud with conventional methods and apparatus. Mud filtrate pH was estimated with Hydrion pH paper for the appropriate range. Streaming PotentIals Across MuD Cakes Commercial calomel-saturated KC1 electrodes are subject to potential changes attributed to contamination of the very small fiber-tip bridge by particles of clay from the drilling mud.3 To minimize this difficulty, a large diameter bridge (Fig. 1) was constructed with saturated KC1-agar gel and a filter disc of microporous porcelain. Experiments showed that streaming potentials across this bridge are less than 0.2 mv at pressure dif-

By Murali M. Gadde

Welded wire mesh is the most commonly used skin control technique in the United States underground coal mines. Currently, selection of the mesh is based on trial and error rather than any rigorous design methodology. Several factors affect a wire mesh?s performance including the amount of rock material to be supported and how the load is distributed, wire gauge, aperture size, grade of steel, weld strength, bolting pattern and sheet size. Although the best way to choose the mesh is to conduct full-scale physical load tests, because of the limitations on the number of variables that can be considered in such tests and the requirement of an elaborate test set-up, it may not always be possible to use this option. An alternative would be to use numerical modeling to study the load-deformation behavior of a wire mesh. In addition to providing a very detailed stress, strain distribution in the entire mesh, the advantage of this approach is the ease with which parametric studies can be conducted. In this paper it is shown that the load-deformation curves generated by nonlinear numerical models match closely with laboratory derived ones. Then, based on parametric studies, design guidelines are developed to choose the mesh appropriate for different loading conditions. The modeling studies also bring forth the limitations of the current lab studies. For example, under some conditions it was noticed that the small sheet size considered in lab tests would produce higher mesh deformations than a full-size one used in actual practice.

Jan 1, 2006

By Conny Postupack

The first principle one usually learns about blasting is that competence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced in a new area, may have co make one or two himself to the new conditions with which he blaster when operating shots just to acclimate is faced.

Jan 1, 1991

By Mehrotra G. M, Frohberg M. G

Based on the concepts of statistical thermodynamics of athermal mixtures, an approach is developed which is capable of quantitatively explaining the thermodynamic properties of binary silicate systems. Expressions for the ionic fractions of various anionic linear and nonlinear chain polymers are derived. The developed expressions for free energy of mixing are tested by applying these to the system PbO-SiO2. The ionic fractions of various chain polymers in this system are calculated. The two cases, namely, of linear and nonlinear chain polymers are compared with each other.Limitations of earlier models are pointed out.

Jan 1, 1975

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

By Don W. Deere

Faults under high rock cover represent some of the most severe ground conditions a Tunneler can encounter. High ground water pressures and flows are usually associated with mountain faults. Ground behavior can range from blocky ground to flowing sands and squeezing clays. Sticking a IBM within a fault zone for many weeks, with the disastrous financial consequences, is still a common occurrence. Interpreting the geology and detecting the location of a fault prior to penetrating it is a fundamental step to successful tunneling. Ground water control through predraining or pre-grouting is the second fundamental step. This paper discusses techniques applied for detecting and crossing mountainous fault zones through the use of case histories across the globe.

Jan 1, 2007

By M. K. Sichone

Anglo Platinum?s Waterval smelting complex based in South Africa operates the Anglo Converting Process (ACP) that produces SO2 offgas. This SO2 offgas is treated in a double-contact, double-absorption acid plant allowing for conversion efficiencies higher than 99.90 %. The catalytic converter used in the acid plant to convert the SO2 to SO3 is a 4-bed reactor loaded with a combination of cesium-promoted and conventional vanadium pentoxide catalysts. In June 2008 there was a shutdown, in which one of the main activities was to screen the catalyst. Before this shutdown, the operator would control the converter pass temperatures manually, via the SCADA, especially during plant start-ups after which some of the automatic temperature controllers were used. After the shutdown, the control philosophy was revisited and all temperature controllers were put on auto mode during plant start up. Furthermore the set points of the pass inlet temperatures were reduced to maximize conversion in the first two passes. The result has been a reduction of SO2 emissions, from a daily average of 50 ? 70 ppm to as low as 20 ppm for similar sulphur dioxide and oxygen concentrations. Further work has been done to maintain high bed temperatures in the third and fourth passes at low SO2 strengths by splitting the gas stream between pass 1 and 2 thus increasing the SO2 content in the gas to pass 2. This increases the temperature of the gas exiting the second pass, which results in higher temperatures in passes 3 and 4. Comparison of the converter performance prior to and after the changes is made. The benefits of partially bypassing the first pass to increase the SO2 content in the gas to the second pass are shown. Conclusions and scope for further work have been drawn from the comparisons.

Jan 1, 2009

By C. Pelley, A. Piche

"The Canadian mining industry faces the prospects of a severe shortage of graduate mining engineers over the next decade. This arises from three factors: first, a growth in industrial activity; second, the average age of company engineering and management staff; and third, the reduced number of students in engineering faculties around the world. This paper aims to identify the critical factors underlying the trend of inadequate recruitment into higher education for mining and to examine means of alleviating the problem.This paper is based upon surveys of potential and current students and graduate mining engineers from four mining schools. An attempt is made to understand institutional and industrial images, career prospects and what is required to attract enough high-calibre young people into mining education over the next decade.IntroductionThe mining industry has started to experience a severe shortage of graduate mining engineers which is likely to persist and even worsen in the short- to medium-term.This arise s from three principal factors:1. a recent and strong growth in mining activity, which surpasses that experienced through the 70s, before the recent international industrial recession; .2. an increasingly older average age of mine engineering employees, at least in the industry's larger companies; and3. problems associated with maintaining adequate mining undergraduate recruitment levels ."

Jan 1, 1989

By Joseph Ribak

Grunerite asbestos (amosite) has been shown in epidemiological and experimental animal studies to cause lung cancer, mesothelioma and pulmonary fibrosis commonly referred to as asbestosis. An overview of the human and experimental animal studies describing the health hazards of grunerite asbestos (amosite) is presented. Of the many human studies describing the health hazards of asbestos, only three factories using mainly, if not exclusively, grunerite asbestos (amosite) have been studied. The first is a series of reports on a cohort of 820 workers from a plant located in Paterson, NJ. Among this cohort, 18.7% died of lung cancer and 17 mesotheliomas occurred. The Paterson factory closed in 1954 and moved to Tyler, Texas where it operated until 1972. Among the 1130 former workers in the Tyler plant 6 mesotheliomas were reported with 15.8% lung cancer mortality. The third grunerite asbestos (amosite) exposed cohort was an insulation board manufacturing facility in Uxbridge, United Kingdom. Here 17.1% of the workers died of lung cancer and 5 mesotheliomas occurred. The lung content from 48 Uxbridge workers was analyzed by analytical transmission electron microscopy for mineral fibers. The relationship between grunerite asbestos (amosite) concentrations in the lung correlated with grades of fibrosis and asbestos bodies and was lower than the concentration found in the cases with malignant tumors. The lung cancer cases contained more grunerite asbestos (amosite) than mesothelioma cases, and in the cases of non-alignant disease the concentrations were still lower. In both types of malignancies the concentration of grunerite asbestos (amosite) was very high-over a billion fibers per gram of dried lung tissue. Occupational exposure to airborne concentrations of between 14 and 100 fibers of grunerite asbestos (amosite) per milliliter after 20 year latency causes marked increases in lung cancer, mesothelioma and pulmonary fibrosis (asbestosis). © 2007 Elsevier Inc. All rights reserved. Keywords: Grunerite asbestos; Amosite; Mesothelioma; Asbestosis

Jan 1, 2007

By Virgil Miller, Glenn L. Allen

The purpose of this report is to present a comprehensive review of the technology of alumina and aluminum production in the former Japanese Empire , which consisted of the Japanese Home Islands and her dependencies , Formosa , Manchuria , and Korea . Pertinent background material and statistics are given when deemed necessary to make the report self - contained and to make clear the factors underlying Japan's tremendous accomplishments in the production of aluminum .

Apr 1, 1949

Air tabling of zircon-rich non-conductor products containing quartz enables most of the fine quartz present to be rejected without a markedloss of zircon. The coarser quartz in the air table feed can be separated from the zircon by screening one or more air table products, the oversize products containing most of the quartz and little of the zircon. Air tabling, with or without screening, is more efficient than wet tabling alone for the removal of fine quartz, but not for the removal of coarse quartz. Practically all of the quartz can be separated from the zircon by using wet tabling in conjunction with hydraulic classification, or by using air tabling in conjunction with dry launder treatment, in which a degree of sizing takes place that is advantageous for subsequent air tabling.INTRODUCTIONBack-dune and inland beach sand deposits usually contain fine wind-blown quartz, and neither spiral nor wet table concentration, alone or in conjunction, makes a clean separation of heavy minerals from quartz. Many rutile plants recover rutile and zircon from a low-quartz, wet-table concentrates by means of magnetic and electrostatic separation; some rutile and zircon are lost in the table tailings. Other rutile plants, and two of the ilmenite plants in Western Australia, recover rutile or ilmenite respectively, from a spiral concentrate containing several per cent of quartz, and then subject the non-conductor product to an additionalgravity concentration process to separate the zircon from the quartz. Some zircon is lost in the additional gravity process, but all of the rutile or ilmenite in the spiral concentrate is, or should be, recovered as high-grade concentrate. The higher recovery of rutile or ilmenite by this treatment method is offset by the expense of drying part of the feed twice, as a wet process is usually used to separate the quartz...

Jan 1, 1962

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumedmetabolic rate of 325W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ?Tgi and ?HR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ?Tgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

Nov 8, 2019

By Ashutosh S. Dhar

Cast-in-place piles were examined in this paper from the viewpoints of construction quality, axial capacity, and load-displacement responses. The results of ten 450 mm diameter (18? f) bored piles, installed in a soil deposit of silt to medium dense sand using the method of percussion drilling, were tested under static loads. The results of the pile load tests were used for evaluation of various design methods of calculating pile capacity. The study revealed that the design methods based on the concept of critical depth underestimated the ultimate skin fiction. Thus, the applicability of the critical depth concept for design of bored piles under the soil condition considered may be unreliable. The estimated skin friction factor, ß, was too low in these methods. The Tomlinson method and the Neely method provided the best prediction of the ultimate skin friction. The methods used for calculating end bearing resistance were found to provide a conservative estimate of the resistance. During pile load tests, a settlement of 5 to 6 mm was required for full mobilization of skin friction for the piles in loose sand, while larger settlements (> 10 mm) were required for piles in denser soil. The ultimate skin frictional resistance was observed to be low for piles in loose sand.

Jan 1, 2006