Search Documents

By Padmavathy Mahadevan, Samir Chefai, Eduard Guerra

"Electrocoagulation is a technique for treating wastewater streams from metallurgical plants whereby electrodes are corroded to generate gases (most notably oxygen at the anode and hydrogen at the cathode) and solid particulates which acts as substrates for coprecipitation of impurities. The performance of electrocoagulation reactors, in terms of their efficiency for removing a particular impurity, is highly dependent on several factors, most notably: the nature of the electrodes, the spacing between electrodes, the current density, the height of the electrodes, the solution flow rate, and application of periodic current reversal. Because these variables have complex interactions, in order to ensure reliable scale-up of laboratory results, experiments should be conducted under conditions that closely match those that would be employed at an industrial scale. To that end, this article describes the design and commissioning of a versatile laboratory scale electrocoagulation reactor that allows for the control of all the aforementioned variables along with the ability to measure the instantaneous spatial distribution of current within the reactor.IntroductionArsenic is often removed from metallurgical waste streams in stirred tank reactors by coprecipitating it with ferric ions as an arsenical ferrihydrite [ 1]. Electrocoagulation is an electrolytic technology that can accomplish the same task, but has not yet been widely adopted to treat metallurgical waste streams [2]. The electrocoagulation process involves the use of an external DC power supply to drive the dissolution of a relatively non-toxic metal into the wastewater stream, usually either iron or aluminum, which then largely precipitates as oxyhydroxide phases that adsorb undesired impurities [l]. At the anode, the metal is dissolved and oxygen is often evolved, lowering the local pH and enhancing metal ion solubility."

Jan 1, 2012

By James L. Whitlock

Biological treatment of mining and industrial effluents reached full scale commercialization around 1980. These proven, low cost, technologies have been limited in application due to a number of factors, including extended periods of time and cost required for pilot testing as compared to chemical treatment technologies, lack of biological expertise in metallurgical personnel, longer treatment periods in some cases, and performance failures based on improper application. Renewed interest in biological treatment technologies is being driven by permits with lower effluent concentration criteria, permits with bioassay evaluation, the need to remove thiocyanate, nitrates, sulfates and? other parameters. Chemical treatment processes, in general, have not been able to meet these present requirements, or require elaborate? combinations of processes, in terms of effluent quality and treatment economics. This paper addresses biologieal treatment of mining and industrial waste waters and selected recent advances in these technologies. The future looks very bright for application of these low capital and operating cost technologies,

Jan 1, 1998

By Robert S. Sokolowski

The future of Materials Processing in Space (MPS) in the Space Station Era is being assured today by a strong coordinated science program which looks to solve these problems, the answers to which serve to underpin the technical foundation upon which future metallurgical and materials processes will be built. The critical link between the product and process development activities that accompany this science endeavor is the "nuts and bolts" hardware that will ultimately operate in the space environment. Ground-based facilities including drop facilities and aircraft provide excellent product development and process concept study tools. Shuttle flights with Spacelab and commercially developed space facilities represent the evolutionary path to Space Station processing facilities. Today the most promising areas of MPS are crystal growth, containerless, and quasicontainerless processing. The unique features of these processes will be highlighted. Finally a more visionary perspective of MPS will be presented that incorporates the limits of today's knowledge with the economic "necessity" of tomorrow.

Jan 1, 1988

By J. W. Whitney

Itronics Inc., through its wholly owned subsidiary Itronics Metallurgical, Inc. (IMI), has successfully developed technology that allows it to be fully integrated as a photochemical recycler. IMI is now using this technology to expand its regional operation, which collects used photographic chemicals, chemically removes 99.997% of the silver and uses the residual to make a line of high quality liquid multinutrient liquid fertilizer products. Elevated silver discharges from the Reno-Sparks sewage treatment facility, that were traced back to incoming waste photographic chemicals and which were seriously impacting the sensitive fishery, provided the impetus for this project. This paper is updated from a paper presented at the Twenty-Second International Precious Metals Conference Toronto, Ontario, Canada in June 1998. It presents an overview of the scope of the problem solved by the technology, some of the permitting and development issues, and some of the specific fertilization formulations that are now being marketed.

Jan 1, 2000

By R. W. Lee

The first prototype plant using the Imperial Smelting Process commenced operation in 1950. It is timely therefore to review the developments that have occurred with the process over the past half-century. A major advantage claimed initially for the process was its ability simultaneously to recover zinc and lead from bulk concentrates. This has remained a fundamental advantage, but it has been extended by the increasing treatment of secondary materials containing zinc and lead. This has been facilitated by the development of hot briquetting and tuyere injection. These techniques and their impact on the technology of the operation will be described. The other major advantage claimed for the process was its potential to achieve new levels of productivity in the pyrometallurgical smelting of zinc. This has been realised with operating furnaces producing up to 400 t/d of zinc. The technical developments that have enabled this scale of operation will be reviewed.

Jan 1, 2000

By Kamal Adham

Hydrochloric acid is used as lixiviant in such hydrometallurgy processes as synthetic rutile production and nickel extraction. The intermediary metal chloride is normally roasted to release gaseous HCl and a solid metal oxide. A large amount of fuel is required for this thermal regeneration, mainly to vaporize the water content of the feed solution. To conserve fuel, some energy recovery from the off-gas is currently achieved, but the fuel costs can further be reduced by process optimization and energy recovery from the gaseous, aqueous and solid products of the regenerator. Here, first the existing limitations to fuel efficiency in the industrial scale HCl regeneration roasters are described. Then, for the case of a dilute feed solution, options for pre-evaporation and fuel minimization are modeled and compared. Finally, energy recovery technologies including heat pumps, acid heat exchangers and solid waste heat boilers are described, and their potentials as the heat source for pre-evaporation of the feed are evaluated.

Jan 1, 2003

By Guo Xueyi

The reaction mechanism for the manganese dioxide reductive dissolution in acidic chloride media in the presence of ferrous/ferric ions are based on theoretical delineation and dual cell experiments. In terms of the Buttler-Volmer equation and chemical kinetic principles, a electrochemical kinetic equation was deduced, which successfully provided a theoretical basis for describing the role of Cl-, Fe2+, Fe3+ and H+ in solution, as well as their interrelationship in manganese dioxide reductive dissolution. Dual cell experimental studies indicate that the increases of Cl- and Fe2 in solution are helpful to accelerate the couple process; while, Fe3and Mn2+ hinder the coupled reaction to some degree. Higher acidity in solution is beneficial to the dissolution of MnO2. All the dual cell experimental results are consistent with the theoretical deduction. This study will be useful to understand the mechanism for the leaching of manganese nodules from the deep ocean, as well as the leaching of manganese dioxide ore from land.

Jan 1, 2003

By P. W. Godbehere

Over the past three years the Horne Smelter has successfully introduced concentrate smelting by injection in Peirce-Smith converters, allowing definitive closure of its last operating reverberatory furnace, while commissioning a large acid plant treating off gases from its Noranda reactor. Future strategies include a major revision to present converter practices to permit further significant reductions in sulphur and dust emissions. This paper gives an overview of the status of these and other technical and operating developments which will further contribute to ensuring the Horne's position as an efficient custom smelter of primary and secondary feeds.

Jan 1, 1993

By Jason Eric Sallee

Ongoing operations at the Cyprus Miami Smelter involve the use of an electric furnace for settling of copper matte from discard slag. Proper operation of the electric settling furnace is a major factor in minimizing losses of copper to the discard slag. Recent test work at the smelter has shown improvement in the operation of the electric furnace with a subsequent improvement with regard to the copper losses. This paper presents a general discussion of the Cyprus Miami Smelter operation, past results with respect to copper losses, recent operational changes and test work, and the subsequent results.

Jan 1, 1999

By Khoo Khyou Pin, Yoshiyuki Funaki, Hirotsugu Takeuchi, Ryoichi Urao, Naotatsu Asahi

"Steel is used to be ion carburized with mixing gas of methane and hydrogen. In carburizing, carbon in the methane decomposes and deposits on the steel by plasma, so methane gas flow may influence on ion carburizing of the steel. An apparatus in which works can transfer preheating, ion-carburizing and diffusion treating zones continuously was made for effective carburizing of steel. The gases were flown into above three zones with three different gas inlets. The hardness and microstructure of the works were investigated after ion carburizing and quenching. The steel is carburized deeper near the carburizing gas flow nozzle of the inlet than far from the nozzle. Hard surface layer fom1ed by quenching of ion-carburized steel.IntroductionGas carburizing is used for a surface hardening treatment which decreases fatigue and wear of the industrial parts used in automobile, machines etc. Ion and vacuum carburizing have been developed recently and applied to some industrial parts of restrictive purposes. The ion carburizing treatment which uses hollow cathode discharge (HCD ion-carburizing) is superior in energy saving, resource saving, environmental cleanness to the other carburizing treatment. Specially, carburizing energy can be saved in HCD ion-carburizing, because highly heated zone can be restricted in the range between work and subsidiary cathode where hollow cathode discharge arises, and the work is carburized in shorter tin1e in HCD ion carburizing method than other carburizing methods. Three treatments of preheating, carburizing methods and carbon potential controlling by hollow cathode discharge tried to be carried out in one continuous transferring series to carburize works more effectively, so the HCD ion-carburizing apparatus with continuous transferring system was made and gears of works were HCD ion-carburized in continuous transferring. The works were rotated themselves to get homogeneous carburizing by continuous transferring in glow of hollow cathode discharge."

Jan 1, 2000

By Robert Kozicki, Eric Graham, George Wrightson

"IntroductionThe manufacture of Ferro Chromium involves the smelting of various ores and fluxes to produce the metallic product.Slag is inherent in the process. It has a much lower density than the metallic FeCr. Some chrome may be trapped in the slag as either FeCr or Cr203.Previous methods to estimate the slag in the FeCr have revolved around separating the slag and metallic portions by exploiting the differences in density. The downside with that procedure is that material will often contain pieces that are adhered FeCr and slag. The Metallic FeCr may also be completely encapsulated in the slag.An alternative and more precise method involves calculating the slag content based on chemical analysis of Mg and Al. The Mg and Al will be at relatively low levels (less than 0.1 % ) in the Metallic FeCr pieces and considerably higher in the slag (3% or greater). The overall sample will have a proportional amount and is calculated using simultaneous equations with the assumption there is only one kind of slag and one kind ofFeCr present. ""Pure"" slag and ""pure"" FeCr are needed in order to determine the Mg and Al in each. The detemlination of the Mg and Al in the overall sample would then be used to calculate the amount of slag.When the particle size is small, it is difficult to sample and get ""pure"" pieces of the slag and FeCr of sufficient quantity to perform a proper analysis. Often, historic data is used but that is dependent on the source of the FeCr and the materials used in its production. Mg and Al levels in slag can vary between 3% and 20% in different FeCr slags depending on their origin."

Jan 1, 2013

By Donghai Li, Cheng Pan, Xuyang Liu, Xuewei Lv, Chenguang Bai

"Fine chromite ore is the common raw material to produce ferrochrome alloy through the submerged electric furnace process. The electric resistivity of fine chromite ore plays an important role in the operation efficiency because it determines the current distribution. The effect of particle size and the contact area of the particles on electric resistivity for several of chromite were investigated at room temperature, and the relationship between the electric resistivity of mixed particles and the volume fraction of lump ore to fine ore was also studied. The results shown that the electric resistivity increases with the increase of particle size, and the electric resistivity of mixture decreases with the increase of volume ratio of fine ore.IntroductionChromium is one of the most important alloying elements in manufacturing of stainless steel that used at high temperature and corrosive environment applications [I, 2]. As the raw materials to be charged into the steel, ferrochromium alloys and charge chromium are produced directly by smelting of chromite ore with the reducing agent in submerged electric arc furnace (SAF). During the process, the oxides of chromium and iron were reduced by carbon and meanwhile the electrical energy were consumed [3,4]. The ideal industrial process is to achieve high recovery level of Cr and Fe with minimal power consumption. In SAF process, the electric resistivity of charge stock has significant effect on the current distribution, which determines the heat distribution, molten bath structure and chemical reactions in the furnace. High resistance of the charge is desired to reduce the current distribution through the charge stock, thus the electrodes may insert into the charge stock with proper depth to form a high temperature arc heat source, and proper smelting can be realized[5]."

Jan 1, 2012

By D. Kennis

"Union Miniere Precious Metal's (UMPM's) Hoboken Business Unit has a long tradition in complex Pb-Cu metallurgy, focussing on the recovery of precious metals from various types of secondary and recyclable materials. Although the old flow sheet, based on a traditional sinter plant, blast furnace, and lead refinery process was a very complete flow-sheet with the capability of dealing with almost every impurity, the weaknesses became clear:1. old and costly technology,2. too many unit operations,3. too much internal recycling, and4. dependency on concentrates for the sintering process.To maintain the competitiveness of the Hoboken Business Unit, the project ""Smelter 2000"" was born. This project represents a breakthrough in metallurgical processes and technology. A modem smelting technology was chosen together with the development of a new process. A lead-copper process combining lead slag and blister copper production, carried out in an ISASMEL T vessel, was the key to simplifying the Hoboken flowsheet. ISASMEL T smelting technology was chosen for its flexibility towards feed characteristics and process parameters.The new smelter was commissioned at the end of 1997. Although there were a lot of problems due to the high degree of technical innovations in the process, the new smelter came to design capacity within 1 year after start-up. During this period, however, UMPM had, a very difficult time because of the extreme clear-cut nature of going from the old to the new flowsheet.After two and a half years of operation, the new flowsheet has proven to fit with the strategy of UMPM, focussing on treating secondary Pb-Cu materials and a broad range of recyclable feeds such as electronic scrap (E-scrap) and catalysts. Together with the new Precious Metals Plant, efficient logistics, recognised world class sampling practices and a customer-focussed commercial organisation, UMPM Hoboken can definitely be considered reborn."

Jan 1, 2000

By Bora Derin, Onuralp Yucel, M. Seref Sonmez, Murat Alkan

"Latest stage in the production of boron carbide by metallothermic methods using magnesium was the leaching process. Boron carbide particles obtained by self-propagating high temperature synthesis contained several impurities such as magnesium oxide and magnesium borates after the metallothermic reactions. Removal of such contaminates by hydrometallurgical methods required to produce high purity boron carbide. Leaching by concentrated hydrochloric acid solutions resulted in the production of pure boron carbide together with high magnesium and boron containing solutions. Removal of such ions from the spent liquor was the necessity to have dischargeable solution. In this study, precipitation of magnesium and boron compounds from relevant chloride containing spent liquors and the production of saleable products was aimed. The effects of chemical reagents, pH of the solution on the precipitation efficiency of magnesium and boron compounds were investigated in the study. Chemical analysis and the characterisationof solid phases by using x-ray diffraction analysis were the latest stage.Introduction A variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers can be synthesized by using different SHS techniques [1, 2, 3]. In the SHS process, after initiation, reaction becomes self-sustaining and propagates in the reactant mixture. A high amount of heat which is generated during the process accelerates the reaction rate and thus it makes the process highly productive and economically feasible for different production scales. After the SHS process obtained powder mixture needs to reacted with acidic solutions to purify the product. In this case B2O3 was reacted together with C and Mg to synthesis fine B4C powder resulted in the production of MgO as well according to the Eq. 1 and then MgO was removed from the mixture by leaching with the concentrated HCl solution as shown in Eq. 2, respectively [4, 5]."

Jan 1, 2008

By Takahiko Okura

"It is said that the energy and resources crisis will come before long because the lifetime of known deposits of crude oil and common metals such as Pb, Zn, Cu is estimated to be less than 50 years. Establishing the sustainable society by means of resources-recycling has become an absolute necessity.The non-ferrous metals industry in Japan has been involved in the resource- recycling business for many years, along with the introduction and enforcement of various legislations to preserve the environment and natural resources. Including process-linkage during various manufacturing activities, the non-ferrous metals industry, the iron-making and cement industries are treating considerable amounts of recycled materials and wastes, in an environmentally-sound and economic manner.The Mining and Materials Processing Institute of Japan has submitted “The present and issues in Japanese non-ferrous metals and recycling industries.”The topic of the paper is to highlight the actual conditions within the resources-recycling structures and the present issues.IntroductionGlobalization has been changing the world, introducing the spike of energy and metals price. In addition, the preservation of the environment has also been strongly facing the crisis and many people have been aggrieved by both shortage and the increment in the price of the meals.In the world of metals, even though their reserves are coming depleted, the production rates are increasing, and then the industry has to enhance their productivity under stricter environmental regulations. The Japanese industry experimented the same scenario some 40 years ago, facing big pollution problems, but concurred them and enhanced the technology to overcome the more severe regulations. It will be fruitful to present the current situation in the Japanese industry for the world. The present issues are also presented."

Jan 1, 2008

By Biserka Lucheva, Tzonio Tzonev

"A unique DC electric arc rotary furnace with capacity 150 kg has been designed and constructed for the recycling of low-quality scrap and aluminum dross. The main constructive feature of this furnace is that the axially positioned graphite electrodes (cathode and anode) are placed 100 mm away from the rotation axis of the furnace. A specific characteristic of the construction is the possibility one of the electrodes (the anode) apart from moving axially (parallel to the furnace axis) to move at 90° outside the working space. High recovery rate of metal aluminum from aluminum dross (92%) was realized in this furnace. This is the reason for construction of industrial DC electric arc furnace.IntroductionThe consumption of aluminum waste has been rising continuously on a world scale, which is a great stimulus for the development of the technology for aluminum recycling.To recover the aluminum in dross, the conventional recycling process uses salt rotary furnaces heated with a fuel or a gas burner. This treatment process produces a secondary dross containing alumina, salts, impurities and a small amount of aluminum. Molten aluminum is tapped from the furnace and the residue is then dumped from the furnace. It has been the practice to dispose the residue in a landfill. Improvement of this technology, known as the oxy-fuel process, uses a gas burner enriched with oxygen to increase the thermal efficiency [1]. Recent studies show that the most efficient aggregate for recycling of aluminum scrap has turned out to be the rotary tilting furnaces, heated by plasma or electric arc, for which the use of flux is not necessary [2,3].Accordingly, there is a substantial need in the industry for an improved process for recovering free aluminium. It is particularly desirable that such process be cost effective and ecologically safe."

Jan 1, 2008

By Amanda C. Lima, Luiz Augusto H. Terrones, Sergio N. Monteiro

"Fabric from weaved yarns made of jute fibers have been considered as reinforcement for polymeric composites. In particular, these fabrics obtained from discarded sackcloth are presently being investigated as environmentally friendly composites with recycled polyethylene matrix. The objective of the present work was to compare the practical properties and economical aspects of these composites with those of conventional materials such as wooden board and gypsum panels for building application. The comparison showed that, depending on the amount of post-used jute fabric, a cost/benefit analysis favors these composites over the conventional materials.IntroductionThe increasing amount of wastes generated by human activities is becoming a worldwide problem of pollution with growing consequences to the environment. The question on how to dispose these wastes is, therefore, a major global issue. Among the possibilities of it gating the problem, the use of materials with characteristics of being renewable, biodegradable and recyclable is considered an environmentally correct solution. Examples of this type of materials are left over lignocellulosic fiber from coconut husks and sugarcane bagasse [1] that, after the primary extraction of edible pulp and juices, can be recover for industrial application. Nowadays, the main use of these fibers is to reinforce polymeric composites applied as components for building construction and automobile parts [2,3]. In addition to these applications, composites reinforced with residual lignocellulosic fibers may replace conventional furniture and panels made of wood and thus help to reduce deforestation [4].Environmental protection is not the only motivation for recycling natural fiber wastes. In developing regions activities associate with collecting and processing residual fibers provide job opportunities for low-income people. Moreover, if the lignocellulosic fiber is collected as a recyclable waste, it hes the economic advantage of a comparatively cost, which constitutes in a relevant difference as a choice for commercial utilization."

Jan 1, 2008

By Jr. Brown, A. Calderara, A. L. Antozzi

"The result of extensive research into fundamental mixed metal oxide catalyst morphology has produced a next generation all titanium Dimensionally Stable Anode (DSA ®). This new DSA ® anode, patent pending, is tailored for electrowinning of non-ferrous metals (copper, nickel, cobalt, zinc) by means of this new coating technology.These DSA ® anodes are characterized by a hanger bar with vertical distributor bars, having primary titanium mesh attached by weldments. The active mesh is provided with noble-metal electrocatalytic coatings, consisting of iridium and/or ruthenium oxides, obtained by thermal decomposition of precursor solutions applied to the titanium substrates. The catalytic activity of state-of-the-art DSA ® anodes is increased by controlling the crystallite size of the noble-metals without decreasing the decomposition temperature. It is known that below a certain value (typically 400°C) the stability of these oxides, and associated lifetime, is seriously compromised. A highly active DSA ® anode, consisting of a quasi-amorphous phase, is obtained at high temperature (above 450°C), therefore not compromising lifetime performance. Through optimization of these design parameters, the manufacture of these novel anodes was identified.DSA ® anode performance advantages include: lead-free ' green' all titanium anodes, true leadfree cathode quality, energy savings of 0.3 to 0.55 V can be realized depending on the EW application when compared to industry standard lead-alloy anodes, eliminate need for cobalt sulphate addition required for lead anodes, sustainability designed into long-life recoatable anode structures, increase plant cathode output through increased current density operations, improve plant on-stream production, no sludge generated or removed, and improve current distribution producing smooth high efficiency cathode.Introduction of ProductThere are many factors to consider when engineering a high performance DSA ® electrowinning anode. Half of the anode's performance is derived from the physical attributes of the electrocatalyst and methods employed when applying this catalyst to the titanium anode structure. The other half of the performance benefits relate to the proper structural design of the anode. In this paper, we will highlight the anode development program in which De Nora has invested to provide the Electrowinning marketplace with a high performance anode product."

Jan 1, 2012

By C. Niedersberg, M. K. Almeida, R. M. C. Santana, V. G. Dalenogore

"The major source of environmental pollution in urban areas is the transport sector and its impact on human health and the greenhouse is preoccupying. In many works of literature is monitored the pollutants in urban cities, however in specific areas such as universities, they are scarce. Therefore, the aim of this work is to monitorate the gaseous pollutans in a bus terminal at Santa Cruz do Sul University-UNISC and to develop a control framework of the air quality. Six points were selected for monitoring, being one of them inside a bus. The monitoring of CO, HC and CO2 were carried out on arrival and departure of the bus. Preliminary results conducted in a day of spring showed that the most critical condition was during the night shift, where the concentration of CO (200 ppm) was the highest, caused by the vehicles increase, due to the larger number of students.IntroductionAccording to Mascarenhas et al, 2005, air pollutants are responsible for various effects on vegetation, ecosystems and is recognized as one of major public health problems of today, with harmful effect on humans even at levels considered safe by Brazilian legislation.There are numerous scientific papers linking air pollution with respiratory problems, cardiovascular which hinder the daily life because many of these diseases are chronic and may even lead to death, as was noted by Brook et al, 2004.There is a significant increase in the last decades of emissions to air resulting mainly from human activities. Already being observed the relationship of these emissions with the change in global climate, IPCC, 1995.They are a multitude of pollutants from the atmosphere, and its sources and its effects. The effect of Greenhouse gases (GHG), representing less than 1% of the gases in the atmosphere, controlling the flow of energy in the atmosphere. The increase in emissions of greenhouse gases is affecting the Earth's average temperature, which depends on the balance between these flows, in particular the flow of solar radiation reaching the surface and the flow of infrared radiation sent into space.One of the main greenhouse gases to this imbalance is the gas methane (CH4). Methane is produced by anaerobic decomposition of organic substances, through the action of bacteria metanogenic conditions that require highly reduced to its growth. This gas is released into the atmosphere mainly by transport diffusive by aerenchyma (vascular tissue) plant and also by diffusion through the water slide. (Bont et al., 1978)."

Jan 1, 2008

Testing is in progress to address compatibility issues with regard to long term storage of plutonium in contact with two different intermetallic systems. The two intermetallic systems are: 1. dental amalgam, i.e., mercury plus silver alloy powder, and 2. liquid gallium alloy plus copper powder. Both of these are plasto-metallic materials that undergo a solidification reaction at room temperature. Each system is allowed to react in contact with both high-purity alpha plutonium and a delta stabilized plutonium alloy at varying temperatures in an argon atmosphere. Wetting characteristics and possible interaction will be studied metallographically in the post-mortem condition. Complete results including metallographic examinations will be presented.

Jan 1, 1995