Search Documents

By Shadia J. Ikhmayies

"Nanocrystalline fluorine doped tin oxide (Sn02:F) thin films were produced by the spray pyrolysis technique (SP) on glass substrates at a substrate temperature T, = 450 ° C. The hydrated stannous chloride (SnClz.2H20) was used as a precursor and ammonium fluoride (NH4F) and hydrofluoric acid (HF) were used as the doping compounds. A comparison between the compositional, morphological and optical properties of the films obtained by using the two doping compounds was performed by using scanning electron microscope (SEM) observations, energy dispersive spectroscopy by X-rays (EDAX) and transmittance measurements. It is found that the films prepared by using HF have larger grain size, and higher fluorine content than the films prepared by using ~- In addition these films have higher transmittance and higher direct optical bandgap energy. These results are interesting for the use of Sn02:F as a forecontact in CdS/CdTe solar cells.IntroductionTin dioxide is an n-type, wide bandgap semiconductor (about 3.5 eV) and in the form of thin films, it is a transparent conducting material, characterized by high optical transmission (80- 90%) [l]. Sn02:F is the most widely used transparent-conducting oxide material. The transparent-conducting thin films of this oxide are used as electrodes in a variety of optoelectronic devices, as heat mirror coatings in 'smart windows' for buildings, in automobile and airplane windshields, in incandescent light bulbs, in flat-plate and concentrating solar collectors. Tin oxide and zinc oxide, in thin film configuration are technologically important materials because of their applications in photovoltaic cells [2].Among various dopants for Sn02, fluorine is often preferred, because fluorine doping results in films with high transparency and good conductivity [3]. By exploring the literatures, it was found that different sources of fluorine were used to produce Sn02:F thin fihns, among which are ammonium fluoride (NH4F) and hydrofluoric acid (HF) are the most used. Some researchers used~ [2, 4-7] and others used HF [3, 6-8] for doping Sn02 films. Gordillo et al.[7] used both of NH4F and HF and showed that the resistivity of thin films obtained by using HF was lower than that of similar films obtained by using NH4F by a factor of 2.2. They also found that the films obtained by using HF have more random orientations."

Jan 1, 2013

By Mingming Zhang

"Three samples received from the EAF shop have been characterized by chemical, X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM) methods. The objective of this characterization work is to investigate the occurrence of nickel, copper, zinc, sulfur and phosphorus in these samples and identity their origin and associations with iron minerals in the concentrate samples that are from mines.The samples were identified as Mineral, Pellet, and HRD. The latter is the DR! product. All three samples were received as fine powders. The results indicate that, in the mineral sample, magnetite is the major iron oxide mineral with hematite as a second phase based on the OM and XRD studies. Pyrite [FeS2], chalcopyrite [CuFeS2] and bravoite [(Fe,Ni)S2] are major sulfide minerals. Trace amounts of apatite [Ca5(P04)3(F,Cl,OH)], wardite [Na4CaA112(P04)8(OH)8 6H20], giniite [Fe5(P04)4(OH)3 2H20] and vivianite [Fe3(p04)2 8H20] were identified by SEM and XRD. Microscopic studies also indicated that most of the sulfide grains in the mineral sample are present either as liberated fine particles (about 10 microns) or as inclusions within the magnetite and hematite grains. XRD studies revealed magnetite as the major mineral with subordinate amounts of hematite and pyrite confirming the microscopic findings. Copper, nickel, and zinc are mainly present as chalcopyrite, bravoite, and franklinite [(Zn,Mn,Fe)(Fe,Mn)204] in trace amount in the mineral samples, respectively. Impurities carry over to the Pellet and HRD samples.Chemical analyses of the three iron-bearing samples indicate that sulfur and phosphorus in the Pellet sample exceeded the specification. Since liberated pyrite and chalcopyrite particles were observed both in mineral and pellet samples, magnetic and flotation processing routes for this ore should be effective for sulfide removal but at the cost of iron losses. The high phosphorus content of all three samples indicates that there are phosphates which are difficult to remove by the current concentrating process (magnetic separation and flotation)"

Jan 1, 2012

By Li Rongxing

A general regular solution model put forward in this paper defines a general interaction parameter that includes both composition and temperature dependence. On the basis of this model, analytic express of solution excess properties was obtained by least square fit using the composition and temperature relations in binary alloy phase diagram. After some solution excess properties analytic expresses of correlated binary alloy system obtained, the analytic express of ternary alloy system could be obtained by superposition of general geometrical model. The ternary alloy system Pb-Sn-Zn has been predicted in terms of this method and the result was very in agreement with actual measured value.

Jan 1, 2006

By B. Nebreda, I. Vegas, R. Vigil, O. Rodríguez, M. I. Sánchez de Rojas, M. Frías, R. García, J. Urreta

"This paper shows the possibility of reutilize paper sludge waste as supplementary cementing material for the cement manufacture. This industrial waste consists essentially of a mixture of organic matter (30%) and inorganic compound, such as calcite and clay minerals. The raw paper sludge does not present pozzolanic properties, but once calcined at 650ºC during 2 hours, exhibits high pozzolanic activity, similar to silica fume at 28 days, as a consequence of the transformation of kaolinite into metakaolinite. Calcined paper sludge was used as partial Portland cement replacements of 0, 5, 10 and 20%. Enhancement in compressive strength was appreciably obtained for 10 and 20% substitution levels from 7 days on. Furthermore, calcined paper sludge slightly reduces the initial and final setting times of cement paste. Introduction Natural pozzolanic materials have been ordinary used in different aspects of construction, mainly for their influence on the microstructure and durability of blended cement matrixes [1, 2]. Due to the regulations of environmental protection, many researches are focusing on the possibility of obtaining pozzolanic materials from industrial wastes and not from natural materials (ceramic wastes, silica fume (SF), activated clays) [3–5]. One of the most used pozzolanic products is the metakaolin (MK) obtained from the activation of natural clay (kaolinite). The positive effect that MK has on blended cement performances [6,7] and also the influence that curing temperature and matrix nature have on the reaction kinetics and stability of hydrated phases produced during the pozzolanic reaction, according to the studies carried out by Frías et al. [8,9] are well known. However, there is a worldwide trend towards the use of recycled products in cement industry. In this line, some authors have reported an alternative way of obtaining MK from waste paper sludge [10-14]. The raw paper sludge (PS), once calcined under controlled conditions (700-800ºC), produces a MK with pozzolanic properties [15-20]. The present research is part of an experimental study about alternative source for MK from the Spanish paper recycling industry and its use as supplementary cementing material. This contribution pays special attention to the option of reducing activation temperature below 700ºC. This fact has a positive effect in reducing the energy consumption, as well as in reducing environmental impacts associated with decarbonation of calcite. The chemical and mineralogical characteristics of raw paper sludge and derived calcined product are described. In addition, the influence and behavior on blended cement properties (setting times and mechanical properties) are also discussed."

Jan 1, 2008

By Gaifeng Xue, Lei Zhang, Xia Liu, Lina Wang, Pu Liu, Benquan Fu

"Experiments were conducted to investigate the behavior of the integrated process with a three-dimensional electrode reactor combined with Fenton process for coking wastewater treatment. Effects of initial pH value, reaction time, H20 2 dosage, Fe2+ dosage on Total organic carbon (f OC) removal rate were investigated. The kinetics of degradation of TOC from coking wastewater by three-dimensional fluid bed electrode reactor combined with Fenton process was also studied. Experimental results shows that three-dimensional fluid bed electrode reactor combined with Fenton process had better synergic effect, average 17.4% TOC removal rate was improved within an hour. It was found that TOC degradation in coking wastewater followed a pseudo-first-order reaction kinetic model. The optimum degradation efficiencies of TOC were up to 60% as pH3.4, 3.5 mM ofFe2+ andl.2-1.8ml/L H20 2 in 90min reaction period. Furthermore, the integrated process showed a rapid reaction performance at a low temperature within a short reaction time and remained high efficiencies for TOC removal. Overall, the integrated process was proved feasible for coking wastewater treatment in practical applications.IntroductionCoking wastewater is generated from coal coking, coal gas purification, and by-product recovery processes of coking, which is composed of phenolic compounds, heterocyclic compounds, polycyclic aromatic hydrocarbons, ammonia, cyanide, polycyclic nitrogen-containing aromatics, acyclic compounds, etc. Most of these constituents are refractory, poor biodegradability, toxic and carcinogenic['-31. Currently, coking wastewater is usually treated by different forms of A/O biological nitrogen removal process as the primary treatment process, but the aforementioned processes are not efficient enough to meet the requirements from the National Discharge Standard in China (GB13456-1992). According to the continuous requirement on improving environmental protection for coking industry (revised 2008), increasing wastewater utilization ratio and reducing discharge of effluent in the coke industry has to be implemented for cleaner production and sustainable development. Therefore, advanced technologies need to be developed to treat coking wastewater and reutilize the product as industrial cooling water, which would be one of the best choices to achieve zero discharge of wastewater and reduce water consumption per ton of steel [4-51 . In this study, three-dimensional fluidized bed electrode reactor combined with Fenton process was adopted to advanced treatment of coking wastewater, and the effects of operating conditions, including H2O 2 dosage, Fe2+ dosage, initial pH, and reaction time on TOC removal rate, were investigated. Meantime, study of kinetics of reaction was estimated."

Jan 1, 2013

By K. A. Elbarawy

Processing of Egyptian barite ore with a composition of 85.5% BaSO4; 2.75%SiO2;1.56%Fe2O3 and 5.1% Al2O3 was performed with the aim to prepare pure barium salts. The process took place through pelletization-solid state reduction and leaching steps. Each of these steps was optimized. Pure barium sulphate (99% < 0.82µm) and carbonate (99%<0.75µm )were the final products. This article deals with the reduction process that occur whn coal was added to the ore during pelletization in the ratio of 5:1 stoichiometry. Optimum reduction of pellets of 8-12mm in diameter was achieved after 60 minutes at 1050oC and under a rate of 5 lmin-1 of nitrogen atmosphere, where 87.79% of the ore was reduced. The kinetic studies showed that the reduction process could be modeled according to the core mechanism of diffusion control in which the effective diffusivity is based on the surface area of unreacted ore. The activation energy calculated was 92.7 kJmol-1.

Jan 1, 2006

By P. R. Seidl, R. C. C. Ribeiro, J. C. G. Correia

"More than 95% of asphalt pavement materials consist of aggregates. The highway and construction industries consume a huge amount of aggregates annually causing considerable energy and environmental losses. The aggregates are usually produced from neighborhood aggregate quarries or form natural aggregate sources. The use of marble and granite wastes from quarries as aggregates might help meet the increasing demands and slow down any detrimental effects on the environment. Chemical and physical results showed that the use of marble and granite wastes from quarries in the asphalt production is quite fusible. Consequently, granite sawmills would perform a clean technology. This technology would also have an economical impact by not spending on basalt extraction.IntroductionThe granite fines generated from sawmills of ornamental rocks comes as a great problem and it lacks undeletable solutions. This problem involves the preservation of the environmental and constitutes one of the subjects more critical the point of view of social beneficiation of the population. The Cachoeiro de Itapemirim County, Espírito Santo State, Brazil is an example, of this problem. In this area, the granite and marble fines generation is around 15.000 ton/year.The problems generated by these residues affect with more emphasis the animals, such as the cattle, which inhaled the water content fines of granite and this residue accumulate in their lungs. Other great problem observed is the sanded of the river and the reduction of aquatic life.This problem is beginning to be set out due to performance of Center of Mineral Technology (CETEM), and of several other organisms of Rio de Janeiro State, aiding the sawmills owner’s. This help consists of teaching the best procedure of discard the residues and studies for its use, for instance the production of mortars, tiles, bricks and road pavements [1]."

Jan 1, 2008

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young&apos;s modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2Si/MgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (P/M) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2JIm is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ forming process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm) and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young&apos;s modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Jens Decker

"In consideration of energy savings the ideal refractory furnace lining should possess the following features:??Lowest thermal conductivity possible in order to avoid heat loss.??Single component lining in order to allow freeze plane changes caused by wear, infiltration and temperature changes of the furnace.??Resistance against mechanical wear from cleaning tools and stirring in order to allow maximum output without equipment downtime due to maintenance.??Resistance against thermo-chemical attack from aluminum and alloying elements.However, refractory materials with a low thermal conductivity typically possess a higher porosity and this leads to lower strengths and resistance against chemical attack and wear. Hence, as a compromise, multi layer linings are required in order to meet energy saving standards.In this paper we present the features of chemically phosphate bonded dense and light weight refractories and how such refractories can contribute to energy savings.IntroductionIn several reports, the U.S Department of Energy published theoretical energy requirement limits for aluminum production as a future target, with recommendations on how to reduce energy losses. The reports provide a basic description of the processes and equipment involved, their interrelationship, and their effects on energy consumed. The report uses onsite process measurements as benchmarks that industry uses to compare performance between facilities and companies [1]. The energy consumptions used in this paper are primarily based on numbers published by the Department of Energy. However, their reports do not consider the potentially significant energy losses from process interruptions due to a lack of preventive maintenance and material deterioration over time. Further, the Department of Energy reports do not consider equipment costs and availability. Energy input to metal output depends on factors beyond energy losses through the furnace wall. For instance, a focus on energy savings should consider fixed output costs due to depreciation of the equipment and the plant."

Jan 1, 2009

By Daojin Cao

Aiming at many controversial reports on Raman spectral pattern of octamolybdate ion in aqueous solution appearing in the literature, a new method for the establishment of corresponding relation between Raman spectral pattern and chemical components of aqueous molybdate solution was put forward using spectroscopy measure and component analyses of saturated solution of ammonium octamolybdate hydrate known structure. It was found that the main characteristic of Raman spectral pattern of the saturated solution was described as the same ?double-peaks, hereinto a weak peak at the boundary? as some literature, but chemical components of the saturated solution were affirmed to be octamolybdate ion (Mo8O264-) and double protonated heptamolybdate ion (H2Mo7O244-), which were in equilibrium in aqueous solution each other. The authors propose that the pattern of the saturated solution can be regarded as the standard pattern of primiparous octamolybdate ion during acidified molybdate solution. It is satisfying that the standard pattern is applied to the identification of primiparous octamolybdate ion during acidified molybdate solution.

Jan 1, 2006

By Deepu Philip, Pratik Agarwal, Ajay Kumar Shukla, Ishani Shukla, G Rajesh

Steel plants generally employ static BOF end point control models to arrive at a given temperature and chemistry at the end of blow. These end point models have now been supplemented with chaos control models to steer the blowing process in the right direction while the blow is in progress. Merely arriving at the correct end point temperature is however not adequate because in the subsequent stages as well the temperature variations can be large and unpredictable. The present paper deals with an integrated model to take into account the effect of all parameters affecting temperature and composition from tapping to the start of casting to minimize the use of LF or aluminum heating, and also minimize grade mixing. The application of lean operations strategy is explained in which the previous “Push System’ is changed to a “Pull System”, minimizing the use of ladle furnace or aluminum heating during steelmaking.

Jan 1, 2014

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By Tetsuro Sakai

Home appliance recycling law was put into force in April 2001 in Japan. Specified kinds of home appliances, such as air conditioners, television sets, refrigerators and washing machines, should be recycled according to the law. Mitsubishi Materials Corporation (MMC) in cooperation with home appliance manufacturers is operating five home appliance recycling plants in Japan. MMC established complete treatment system of recyclable materials generating from home appliance recycling plants, which is formed by unique collaboration among home appliance recycling plants, copper smelter and refinery, and cement plants. Recyclable materials containing copper and precious metals are only handled and treated within the MMC group. By using this lock-in system, safe treatment and traceability of materials are guaranteed as 100% materials recycle.

Jan 1, 2008

By Jukka S. Sulanto

Outokumpu has applied its well -known copper Fl ash Smelling Process also for smelting su1phide lead . concentrates. The lead in the Flash Smelting Furnace slag is recovered by reducing the oxygen potential of the slag in an electric furnace by injecting reductant into the slag bath. A series of tests have been carried out in a 1000 KVA electric furnace? adjacent to a pilot Flash Smelting Furnace. The furnace has been fed continuously with molten Flash Furnace Slag. The feed rate has varied from 0.5 to 3.1 MTPH (0.55 - 3..4 STPH) depending on the feed rate and the quality of concentrate to the Flash Smelting Furnace. The inlet slag contained 15 to 40% of lead and the cleaned slag 1. 5 to 3. 0%. The lead recovery from sol id raw material was tested in the same continuous process by feeding lead calcine into the furnace. Feed rate was 0.7 to 0.95 MTPH (0.8 - 1.05 STPH) and the calcine contained 33 to 34% of Pb. Several reduction agents and procedures were tested. The process proved to be suitable for continuous recovery of lead from solid oxide raw materials.

Jan 1, 1990

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

The method of ultrasonic-assisted leaching was used to extract vanadium from the stone coal, with alkali as leaching reagent. The effects of ultrasonic power, concentration of alkali, reaction temperature, liquid-solid ratio and reaction time were investigated, respectively. The optimal ultrasonic leaching condition for vanadium extraction is as follows: ultrasonic power 230W, concentration of alkali 5%, liquid-solid ratio 3:1, reaction temperature 90℃ and reaction time 1h. The leaching rate of vanadium reaches 76.4% under the optimal condition, which is 12.2% higher than that of non-ultrasonic leaching. The reason on enhancing the leaching rate of vanadium by ultrasonic leaching was discussed. It is indicated that the ultrasonic cavitation can increase the surface area of mineral, which is beneficial to facilitate the reaction rate. Keywords: stone coal; vanadium; alkaline leaching; ultrasonic

Jan 1, 2014

By Andrew Campbell, Michael Reed

"WorleyParsons has used Discrete Event Simulation methods in conjunction with more traditional process models to assess the performance of copper smelting operations. This work was performed to determine the plant capacities and suitability of proposed debottlenecking options including accounting for the planned and unplanned (breakdowns) shutdowns in the various parts of the plant and supply chain. This paper outlines the methods used along with demonstrating the benefits of selecting a feasible option and minimizing capital and operating costs.IntroductionTraditionally for de bottlenecking studies of smelters and other process plants, a mass balance is performed based on continuous operating rates and expected operating hours. Smelters have several points of failure that will restrict, if not take the entire plant offline. By using a more detailed model, validated against plant experience, bottlenecks can be demonstrated and strategies to remove them to increase plant availability and economic.The modeling simulates the plant performance in real time, and by performing enough simulation the expected long run performance of the plant can be estimated. The models have been built using ExtendSim which is a powerful Discrete Event Simulation software package that is ideally suited to the batch and semi-batch processes and events that occur within smelter operating environments. The value of performing this work is that the operational performance of the plant can be assessed ensuring production targets are met, without using excessive capital outlay."

Jan 1, 2013

By Klaus Bauckhage

Phase-Doppler-anemometry (PDA)-measurements have to be taken from representative measuring positions from inside the spray cone, helping - with the support of simulated data of improved process models - to describe the multiphase flow situations within the spray cone - and accordingly to that - the heat transfer conditions for the rapid cooling and (partly) solidifying melt droplets before their impact onto the substratddeposit. Simulations and PDA-measurements thus give the base to confirm the hypothesis of the existence of a semisolid mixed-layer and it&apos;s influence on the resulting material structure during compaction. The dispersed particles in the spray cone exhibit a cooling and solidification process within a split of a second, which leads - as far as the particles solidify - to a dendritic structure with very short dendritic arm spacings. This causes within the particles extremely short distances for the following equalizing diffision processes taking place on a high temperature level (between liquidus and solidus) in the semisolid mixed-layer of the deposit and explaining the short residence times within this zone of only seconds up to a few minutes. This and the fact that the globular structure of the mushy zone (in the semisolid mixed-layer) leads to an unidirectional crystallization process over very short distances also explains the chemical and morphological ,homogeneity of the sprayed material. The dynamics of these process steps, the very special buffer function of the mixing layer during parameter variations as well as the controlled cooling process of the preform in order to avoid hot cracks influence the quality of the material. Due to the necessity of measuring and controlling the particle bound mass-, momentum- and enthalpy- fluxes to the deposit the PDA-technique has been adapted and modified in order to receive in-line and (in the future) also on-line data from the dynamics of the multiphase flow conditions within the spray chamber.

Jan 1, 1999

By J. R. Addison

Commissioned in September 1987, the Phelps Dodge Morenci, Inc. (PDMI) Central Electrowinning (EW) Tankhouse bas undergone two major expansions in its eleven-year history. A third tankhouse renovation, which began in November 1998, entails complete conversion of the 548-cell facility from a copper starter sheet based operation to Mt. Isa Process stainless steel mother blank technology. This paper outlines the operating history of the Central EW Tankhouse and reviews the conversion process, the rationale that led PDMI to undertake this project, and describes various design optimizations which have been implemented during the conversion.

Jan 1, 1999

By B. Willit, J. Martin

"Continued emphasis on water and energy conservation with less operator attention has created a need for more sophisticated cooling tower controls. A joint Betz/ASARCO project has produced a computerized water parameter controller and automated pumpless feed unit. Interfacing the unit via radio modem to the operator control room computer allows real time system status monitoring. Incorporating SPC principles to monitor and regulate all pertinent parameters yielded enhanced water control. This paper described the system design and present the results of a six month trial.BackgroundReducing operating costs and better manpower utilization are two of the largest concerns confronting maintenance managers today. At the ASARCO plant in Amarillo, a trial has been initiated to prove that it is possible to accomplish both of these objectives by using automated cooling tower control. The system is being adapted from a unit that was designed for continuously operating cooling towers in refineries and power plants by Betz Equipment Systems Division, a subsidiary of Betz Laboratories, Inc. The System l3000™ is designed to continually monitor conditions in the cooling system and to provide adjustments to the chemical balance for corrosion and deposition control. At Asarco, the unit was installed on the Rodline cooling system which operates on an intermittent basis.The primary justification for this project is to reduce costs of the five cooling systems in the plant. Current procedures require an operator to make visual checks every two hours on the five cooling towers as well as run lab tests on the water to insure proper treatment levels. This manpower can be better utilized by controlling the towers and collecting all the data available at one central location, in this case, the boiler house."

Jan 1, 1989