Search Documents

By Xiaojie Gao, Jingshe Li, Chengsong Liu, Haiyan Tang

In order to clarify the reaction between MnO-SiO2 oxides with low FeO content and Fe-Mn-Si alloy, two diffusion couples were produced by the new method using confocal scanning laser microscopy (CSLM). The interface of the alloy and oxide, content of Mn and Si in the alloy near the interface, size distribution and composition of the particles which precipitated in the alloy were observed and analyzed using the electron probe microanalysis (EPMA). Results show that though the FeO content in the oxides decrease to 1% which is lower than the equilibrium with the molten steel at 1873K, the diffusion of oxygen from oxide to alloy still exists during the heat treatment at 1473K and causes shorter Particle Precipitated Zone (PPZ) and Manganese Depleted Zone (MDZ) normally for the reduction of diffusion flux of oxygen.

Jan 1, 2015

By Ruhi Bux, Akshay Verma, Mohini Saxena, P. Asokan

"Due to the colossal increment in the industrialization, the generation of wastes gathered as a result of different extraction, benefaction and generation processes is having an alarming problem for waste disposal. The best and most acceptable way is to use the waste in accordance to its potential for the generation of high value lucrative composite goods. The study in this paper elucidates the potential of several industrial wastes like fly ash, red mud and marble slurry dust for the production of different wood substitute products like doors, windows, roofing sheets and instant houses for the rehabilitation on the sites of catastrophes. Wastes were initially characterized for the physical, chemical and mineralogical properties and then used in different formulations with binder like Polymer along with natural fiber like Jute to intensify the physical as well as mechanical properties of the resultant composite. The study also reveals that these composites have better mechanical properties than the available ones like teak, medium density board, Rice husk board etc. Also, the fly ash and red mud composites have better mechanical properties than marble slurry based composites. The results fosters the implementation of natural fiber with the industrial waste in the generation of eco-friendly and non-hazardous composites.IntroductionOver the last few decades, there has been a tremendous increase in the generation of industrial wastes gathered as a result of various extractions, benefaction and generation processes. The condition worsens even, when it comes to high quantum generated wastes like Fly ash, Red mud and Marble slurry dust. The primordial motif behind the incorporation of industrial wastes as filler in the development of composites is primarily composed of two main objectives; Firstly waste management, the colossal waste dissemination in the environment has disturbed the ecological balance by polluting land, surface water, ground water, air, natural resources and even disturbing the public health [1]. Secondly, to act as a perfect substitute for the conventionally existing building materials, this will aid in dwelling places to many with the least incorporation of exhaustive natural resources as woods quid pro quo."

Jan 1, 2008

By John A. Mavrogenes

Reflected light microscopy and electron microprobe techniques were used to determine the mineralogy, phase percentages, grain sizes, and textures of Co-Ni-rich mattes. The mattes were produced by submerged bath smelting at the University of Missouri-Rolla Pyrometallurgical Center of a flotation concentrate with 4.S% Co and 5.1% Ni that was prepared at the United States Bureau of Mines Rolla Research Center by flotation up-grading of the cobalt and nickel content of a copper concentrate from the Magmont mine, Viburnum Trend, Southeast Missouri. Nine distinct phases were distinguished in the matte samples, and three of these contain cobalt and nickel. The phases that were free from cobalt and nickel are bornite, chalcocite, pyrrhotite, magnetite, metallic copper, and galena. Submerged bath smelting serves to segregate the cobalt and nickel into phases that can subsequently be recovered by flotation. These phases are: shandite (Ni3PbZSZ)' cobaltpentlandite ((Co,Ni,Fe)9SS)' and Co-bearing Fe-rich sphalerite ((Zn,Fe,Co)S). Most of the cobalt occurs in cobaltpentlandite, but some is present in sphalerite. High total air conditions during smelting favor the development and segregation of cobalt into cobaltpentlandite. Nickel occurs in cobaltpentlandite and shandite. Shandite contains lead, a deleterious constituent in the smelting of cobalt and nickel.

Jan 1, 1989

By Deming Wang, R. A. Overfelt

"The oscillating cup viscometer has become a dominant technique to measure the viscosities of high temperature molten metals. Unfortunately, the viscosity estimation model from the observed logarithmic decrement and period of the oscillation is very complicated. There are still large discrepancies of viscosity estimation values between using different measurement facilities and using different viscosity estimation models for a same molten metal. The purpose of the paper is to evaluate the accuracy of an oscillating cup viscometer in Auburn University. Two well known viscosity estimation models, Roscoe's and Torklep's equations, are compared and discussed. The theoretical literature for the fluid flow inside an oscillating cup is reviewed and a more accurate working equation for the Auburn oscillating cup viscometer is developed. Some design parameters of the oscillating cup viscometer, which directly affect the accuracy of viscosity estimation by using the working equation, are discussed. In addition, applications and experimental measuring data are presented in the paper for several different commercial alloys, such as aluminum alloys: A319, A356 and A201, nickel-base super alloys: In713 and In718, and casting irons, C40 Gray Iron and Ductile Iron.1 IntroductionThe oscillating cup viscometer is the most important and has been most frequently used in viscosity measurement for high temperature liquids [1-4]. The principal advantages of this technique over others are its mechanical simplicity and the ability to measure the time period and amplitude decay with great precision. In the viscometer, a high temperature liquid (such as a molten metal) is contained within a crucible suspended by a wire to form a torsional pendulum, which induces torsional oscillation motion. This motion is damped primarily by viscous dissipation within the viscous liquid inside the cup. The viscosity of the liquid can be calculated by an analytical or numerical solution ofthe equations of motion of the oscillating cup system."

Jan 1, 2001

By J. N. Kondo, M. Hara, T. Smida, N. Ooto, K. Domen

"A porous material composed of two-dimensional anionic sheets of a layered perovskite, KSrNb30 10, was studied as photocatalyst for the production of Hz in the presence of alcohol sacrificial donors. Colloidal single and multi-layered HSr2Nb30 10 sheets were formed by intercalating ietra(n-buthylammonium) cations into the interlayeres of H+-exchanged KSr2Nb30 10 (HSr2Nb30 10), and addition of HN03 solution to the colloidal suspension precipitated the porous materials in which HSrNb30 10 sh~ets rand~mly stuck together. Original HSr2Nb30 10 before exfoliation had a BET surface area of 1 m2 g-1, whereas the surface area of a porous material prepared under optimal conditions exceeded 100 m2 g-1. The porous HSr2Nb30 10 had considerably higher photocatalytic'activitie8 for oxidation of 1-propanol and 1-buthanol than HSr2Nb39io, indicating that in the porous materials many niobate sheets are available for decomposition of these large alcohols.IntroductionQuite a research effort has gone into the design and study of porous materials. Such materials with large surface areas would have applications in highly efficient adsorbents or catalytic reactions.We have been studying photocatalytic reaction by cation-exchangeable layered metal oxides, where alkali metal cations are intercalated into the interlayers of inorganic sheets.[1,2] There are several advantages to using layered compounds rather than bulk powders for photocatalysis. Layered compound is rich in variety, in addition, modifications of them are easily performed by exchanging alkali metal cations in the inter layers for H + or other metal cations. The most important advantage is that some layered compounds have considerably high photocatalytic activities than bulk catalysts because the electrons and holes generated in each thin inorganic sheet readily reach interlayer spaces as reaction sites at the illterlayer spaces. It should be very important for further improvements· of layered photocatalysts to utilize two-dimensional inorganic sheets effectively."

Jan 1, 2000

By Nils Eivind Kamfjord, Roar Jensen, Ingeborg Solheim

"SINTEF has carried out several pilot scale silicon process experiments in the past, but always with an open off gas system. In order to test the possibilities in running a semi closed furnace operation, a new off gas hood has been designed and tested. The off gas hood is designed to collect all off gases to gain insight into the phase compositions in the off gas and at the same time have the opportunity to monitor and maintain the charging/stoking of the furnace. The furnace hood has regulation and control of the air inlet into the combustion zone in two different heights. The off gas temperature and composition was continuously monitored and analyzed during the experiment. In order to expand the knowledge on NOx- formation in silicon metal production, such information is vital.IntroductionBecause of the negative environmental impact, the attention towards all kinds of NOX emissions increases in Norway. The authorities’ demand towards better surveillance and control of emissions increases as well.Earlier and new industrial measurements in FeSi- and Si-metal furnaces reveal quite high NOX-emission. The measurements also show that the NOX formation (mainly as thermal NOX) is distinct connected to the formation of dust (SiO?SiO2) in the combustion chamber above the furnace surface, when the temperature is high and the access to N2/O2 is good. This means that stoking, charging and temperature straight above the furnace surface is important factors for the NOX formation."

Jan 1, 2012

By Kaixi Jiang, Lan Li, Bang Wei, Haibei Wang, Yaping Feng

"China is currently the world's largest copper producer. In the last five years, 950 kt/y of smelting capacity was commissioned. Currently, about 1200 kt/y smelting capacity is under construction and about 2000 kt/y smelting capacity is under feasibility study. Ausmelt/ISA smelting and flash smelting technologies were commonly adopted in China. After the double-flash-smelter was first adopted in 2004, three new double-flash-smelters are scheduled. Recently, two new copper smelting technologies were developed in China. One is an improved bath side-blown smelting process, and another is the SK.S bottom blowing process. Both technologies have been in practice for over three years and have achieved good technical performance. Approximately 500 kt/y new smelting capacity in China and India will adopt these technologies. Both technologies have the advantages of low investment cost, low energy consumption and high flexibility for complex raw materials. This paper reviews ""green"" copper smelting projects in China and introduces the practices of the two new Chinese smelting technologies.IntroductionPresently, China is the largest copper producer in the world. As far as the smelting of copper is concerned, there are many smelting processes applied in industrial production, such as flash smelting, Noranda smelting, Ausmelt smelting, Isa smelting, the Mitsubishi process, Vanukov smelting, silver copper-smelting, SKS smelting, both side-blown smelting, traditional blast furnace smelting, electric furnace smelting, reverberatery smelting and so on . Except the last three traditional processes that are eliminated because of their failure to meet the requirements for environmental protection, all of the other above-mentioned methods are advanced smelting processes adopted nowadays."

Jan 1, 2012

By Garry W. Warren

The brass foundry industry produces a significant amount of waste sand containing Cu, Zn and Pb which is often classified as a hazardous waste due to Pb content. The potential application of a hydrometallurgical process to treat the sand by extracting metal values and thus detoxifying the material has been investigated. The process involves leaching of metal values followed by cementation. The emphasis of this investigation was on the leaching step, although some preliminary cementation experiments have been performed. In order for any alternative treatment scheme to be successful, the smaller size fractions of the sand must be addressed. Experiments have been performed on five individual size fractions using various lixiviants HCI, acetic acid and HCI/NaCI. Cu extraction was found to be slower than either Zn or Pb. Results obtained in this investigation indicate that copper is present in two forms, an oxide form which dissolves rapidly and is insensitive to the level of oxygen, and a less soluble form, probably metallic which dissolves more slowly and requires an oxidizing agent. The presence or absence of oxygen had no influence on the rate of Zn dissolution indicating that zinc is present mostly in oxide form. Toxicity Characteristic Leaching Procedure (TCLP) tests showed that residues could be produced which meet the toxicity limit for lead. Preliminary cementation experiments have also demonstrated the feasibility of Cu and Pb recovery.

Jan 1, 1991

By L. Sh. Tsemekhman

The results of laboratory, large-scale laboratory and commercial scale investigations regarding the process of slag melts cleaning by oxidizing-reduction gas mixtures with a wide range of Po2 and the use of matte of various compositions as an extracting phase are presented. The copper, nickel and cobalt behavior during the cleaning process has been studied based on SEM and x-ray Microprobe of the quenched slag melts. The general cleaning mechanisms have been found. On the basis of the obtained data the most efficient cleaning methods have been proposed.

Jan 1, 2003

By Jie Li, Thomas A. Rawdanowicz, W. J. Collis, S. Venkatraman, S. Iyer

"InSb being the lowest band gap. material amongst the 111-V semiconductors with low effective mass has long attracted research interest, due to its potential application in far infrared devices and for high speed circuit elements. In this paper, we report, for the first time, Te-doping of InSb on GaAs substrate using SnTe doping source with molecular beam epitaxy (MBE) technique and its electrical characterization. The undoped epilayers are n-type in the temperature range of 10 K to 300 K investigated. The room temperature (RT) mobility as high as 64,810 cm2/V·s (1.9x1016 cm-3) have been measured on a 4.8 µm thick epilayer. Sn Te doping at different doping levels were investigated. 5. 7 µm thick doped layers with RT carrier concentrations ranging from 2x1016 cm-3 to 3.2x1018 cm-3 with corresponding full width at half maximum (FWHM) of x-ray (400) rocking curve varying from 170-200 arc-seconds have been achieved. The Hall mobility of 20,000 cm2/V·s at 1.3xl018 cm-3 carrier concentration was obtained indicating that SnTe is a good candidate as source material for n-type doping of InSb.IntroductionThe thin films of InSb and InSb-based alloys have found considerable interest because of potential applications in III-V semiconductor-based infrared optoelectronic devices1• In addition, the advantage of the small effective mass and the consequent high mobility can be utilized in high frequency and high-speed circuit devices2 InSb can also be used in magnetoresistive sensors for position sensing3. Epitaxial InSb films grown by MBE may be doped n-type with Si or Sn, or with the group VI elements, namely, S, Se, or Te. Of the group VI elements, Te may be advantageous because of its relatively low vapor pressure. However, the vapor pressure is high enough to have sufficient memory effect during MBE growth. Hence different telluride compounds such as GaTe45, PbTe6 and Sb2Te37 have been used as the dopant source for Sb-based compounds. SnTe has also been used as a successful n-type dopant in the MBE growth ofGaSb8 But, to our knowledge, there is no report on the investigation of SnTe doping of InSb. In this paper, we report the first doping characteristics of SnTe in InSb layers grown on GaAs substrate."

Jan 1, 1998

By Richard D. Hagni

Ore microscopy is a useful technique to detect and study the ore minerals that are associated with sediment-hosted and volcanic-hosted deposits of finely disseminated gold and silver. Ore microscopy can be used to determine the: 1) precious metal-bearing minerals in some ores, 2) associated ore minerals that may form geochemical exploration halos, 3) character of iron sulfide grains, 4) extent of sulfide oxidation, 5) character of oxidized iron minerals, 6) character of original sulfide grains from a study of the hypogene and supergene oxidized ores, 7) relative time of oxidation, 8) character of organic matter, 9) minerals that may consume excessive amounts of cyanide solution, 10) extent of silicification and silica encapsulation, and 11) possibility of salting.

Jan 1, 1987

By D. Mukerjee, Ramen Datta, Sanak Mishra, R. Veeraraghavan, K. L. Rohira

"Recent efforts at Steel Authority of India Limited (SAIL) has led to the successful development of atmospheric and marine corrosion resistant high tensile Thermo Mechanically Treated (TMT) bars with minimum specified yield strength of 50 kg.mm-2. These rebars are increasingly being used for a wide range of end-applications, namely, concrete reinforcement structures, bridges, flyovers, dams etc. Welding is an important processing tool for each of the above applications. In view of the importance of welding, a comprehensive evaluation of the weldability properties has been carried for the two grades of steels using Submerged Metal Arc Welding (SMAW) process; the most popularly used technique of welding of reinforcement bars (re bars).Implant tests were conducted to assess the cold cracking susceptibility of the steels. The static fatigue limit (SFL) value, determined for the atmospheric corrosion resistant (Cu-TMT) rebars under no preheat and no rebalcing conditions was found to be 63.8 kg mm-2, which was significantly higher than the Minimum Specified Yield Strength (MSYS) (50 kg.mm-2). This indicates adequate resistance to hydrogen induced cracking (HIC). On the other hand, the SFL value obtained for the marine corrosion resistant rebars (Cu-Cr TMT) under no preheat, no rebaking conditions was found to be inconsistent. Repeat of the test with fully rebaked electrodes (350°C-2h) resulted in a high SFL value (60.3 kg mm-2)_The rigidity of the structure or restraint influences the susceptibility of the weld joint to cracking. The cracking tendency increases with restraint intensity (K) of an assembly. The critical restraint intensities determined for the two steels were found to be· in excess of 1680 kg/mm.mm, indicating good welding behaviour with the following welding conditions : for Cu-TMT rebars with no preheat and no rebaking and for Cu-Cr TMT rebars with no preheat and fully baked electrodes; that is under low hydrogen levels."

Jan 1, 1998

By G. Cifuentes

It is known that the cathode purity and the electrolyte treatment are affected by the solids present in the electrolyte. Anodic slimes properties (e.g., chemical composition, crystalline composition, sedimentation) were studied in copper electrorefining. These properties were modified through anodic composition and current density. In this investigation, we have worked with anode material from the Ventana Smelting, Hernan Videla Lira Smelting (ex - Paipote) of ENAMI (National Mining Company) and El Teniente Smelting of CODELCO-Chile (National Corporation of Copper of Chile). The characterization of the anodic slimes was done as a function of current density and anodic composition.

Jan 1, 1999

By G. A. Eltringham, A. F. Sarofim, A. A. Shook, M. P. Heap, B. R. Adams, K. A. Davis

This paper discusses the use of a reacting CFD model to determine chalcopyrite kinetics in a drop tube furnace and to predict the reaction of a chalcopyrite concentrate in the reaction shaft of an industrial smelter. Reacting CFD codes can be applied to determine the consequences of the interaction of gas with particles and therefore improve the ability to derive kinetic parameters that take into account the different temperature and oxidation histories that different particles will see. This paper describes the application of such a model to derive improved kinetic parameters for the pyrolysis and oxidation of chalcopyrite. The improved kinetic parameters derived from the drop tube studies are used to simulate chalcopyrite concentrate reactions in the reaction shaft of an industrial smelter. The reaction shaft model includes the effects of turbulent fluid mechanics, entrained flow mixing, turbulent particle dispersion, heterogeneous particle reactions, radiative and convective heat transfer, and surface and bath deposition rates. Particle reaction and composition characteristics are predicted as a function of particle trajectory and deposition and are used to aid in evaluating shaft performance.

Jan 1, 1999

By Garrett May

We present a periodic technique for measuring the thermal conductivity of thin, disk-shaped samples. In samples of this type, temperature measurements must be made across the sample faces and are therefore subject to large error due to the interface resistance between the temperature sensor and the sample. The technique uses measurements of the amplitude and phase of the periodic temperature across both a reference sample and the unknown material at several different frequencies. Modeling of the heat flow in the sample allows the simultaneous determination of the thermal parameters of the sample as well as the interface resistance. The technique is demonstrated on nanocomposite samples less than 1.0 mm thick.

Jan 1, 2008

By Chai Liyuan

Chromium-containing slag was detoxified by the method of microbial treatment using Ch-1bacteria isolated from nature by our research group, belonging to achromobacter sp. and with the characteristic of reducing high concentration of Cr(VI) in alkaline solution. The detoxifying process of Ch-1 to chromium-containing slag was studied by column-leaching techniques respectively. The results indicate that Cr(VI) in leachate can not be detected when chromium-containing slag has been column-leached for 7 days, and Cr(OH)3 content in precipitate is up to 32.8% with great value of resource recycling. Flowchart of engineering experimentation was ascertained based on the parameters of column-leaching experiments. Using the technique of pelletization of chromium-containing slag heap-leaching by Ch-1,the leaching rate of water-soluble Cr(VI) existing in chromium-containing slag reaches up to 100%, while the leaching rate of full chromium is up to 90%, when the process has been operated for 7-10 days under the conditions of 25-40C and consecutive spray by circular leachate. The content of Cr(VI) in chromium-containing slag after detoxified meet the national identification standard for extraction procedure inxicity for hazardous wastes(GB5085-1996) in China, moreover approximately 90% of Cr(VI) existing in chromium-containing slag has been recycled.

Jan 1, 2006

By Christina Viklund-White

Life Cycle Assessment has been used to compare the environmental performance of landfilling versus recycling of the zinc used for galvanizing steel. Hypothetical process routes were com-posed involving four different EAF dust treatment processes; Waelz kiln, DC-furnace, EZINEX and slag fuming, as well as scrap dezincing. The study shows that recycling of zinc used for galvanizing steel has environmental benefits in that it saves zinc resources. However, zinc recovery does not necessarily decrease the potential impact on global warming and acidification. The magnitude of these two impact categories is tightly correlated with the amount and type of primary energy consumed in a process. Due to the high electricity consumption in the dezincing process, this route has the highest impact on Global Warming Potential as well as Acidification Potential. The major part of the energy requirement for the production of zinc from primary and secondary sources is consumed in the reduction of ZnO to Zn. The consequence is that the theoretically possible savings in primary energy by recycling zinc-containing materials are relatively minor. The impact categories "land use" and "waste generation" are not considered in this study, but most likely the evaluation of such impacts would further increase the potential environmental impact of the landfill alternative. The results also show that the location of an electricity-intensive process highly affects the potential environmental impact. Comparing process and material alternatives in LCA studies where branch average data is used, is considerably more complex than when LCA is used within a company.

Jan 1, 2000

By J. Partinen

Drying is a unit process which has numerous applications in metallurgical process industry. Kumera Technology Center, being a worldwide equipment and process supplier, has developed sophisticated solutions for both direct and indirect drying. In conventional direct drum drying, the energy is taken from combustion of fossil fuels, requiring energy input and emitting considerable amount of off gases. In modem copper smelters, thermal energy from the off gases is recovered in waste heat boilers making the steam available. Using that steam as the energy source for concentrate drying, the total volume of off gases can be considerably reduced and releasing of harmful combustion gases into the atmosphere can be avoided. Kumera Technology Center has recently developed and promotes a new steam drying process for drying of copper concentrates. In the development of the new dryer, Kumera's approach has been to combine the best properties of both the steam dryers and the drum dryers. In the design special attention has been paid to overcome problems of excessive wear and clogging and to reduce the required maintenance operations. In this paper the environmental issues and energy consumption related to both direct and indirect drying processes are discussed. The estimated operation costs and emission levels are compared, based on calculations and the data collected from industry. Finally, the development project of the Kumera Steam Dryer is briefly reviewed

Jan 1, 1999

By Tuneo Funahashi

Sumitomo Shisaka Works has been treating EAF(Electric Arc Furnace) dust to recover zinc and lead in the Waelz Kiln process. Since its commencement of operation in 1977, many technical improvements have been successfully made to increase the production capacity and the zinc recovery rate. The EAF dust charge to the Waelz Kiln was increased from 35,000tly to 120,00OtIy, and the production of zinc oxide now amounts to 40,000tly. The zinc content in the clinker was decreased from 5% to less than I%, by the optimization of the kiln heat pattern with no accretion trouble. And the clinker has become more a valuable raw material for steel making. This paper describes the above progress ofthe SMM Waelz Kiln process operation at the Shisaka Works.

Jan 1, 1998

By H. Y. Sohn, Haitao Wang, Moo Eob Choi

"A novel ironmaking technology is under development at the University of Utah. This technology produces iron directly from iron ore concentrate by gas-solid suspension reduction. Hydrogen is the main reducing agent for high reactivity and for the elimination of carbon dioxide release in this ironmaking process. The direct use of concentrates allows bypassing the problematic pelletization/sintering and cokemaking steps in the steel industry.Intrinsic kinetics of the suspension reduction of magnetite concentrate particles by hydrogen has been measured. Experiments were carried out in the temperature range of 1423-1673 K, other experimental variable being hydrogen partial pressure, the amount of excess hydrogen and particle size. Under most experimental conditions, 95% reduction was attained within several seconds, which presents sufficiently rapid kinetics for a suspension reduction process. The reaction kinetics followed the nucleation-and-growth equation, and a rate equation that contains all the effects of the experimental parameters has been obtained.IntroductionWith the rapid increase in steel production, it is critical to control CO2 emissions which is the main greenhouse gas. It is inevitable to release a huge amount of CO2 when coke and/or coal are used as the main reducing agent in producing iron. As one of the methods to reduce the CO2 emission from ironmaking, the utilization of the gaseous reducing agents and fuels, including hydrogen, has been investigated [1-6]. The use of such gases forms the basis for a new ironmaking technology under development for producing iron directly from fine concentrates by a gas-solid suspension technology. This technology would reduce energy consumption by about 40% of the amount required by the blast furnace and drastically lower environmental pollution, especially CO2 emission, from the steel industry [4]. This is accomplished by adopting H2-based reductant and bypassing pelletization/sintering and cokemaking steps. Unlike other gas-based alternative ironmaking processes using shaft furnaces or fluidized-bed reactors, the suspension reduction technology is a high-intensity process because it will not suffer from the problems that other processes do when operated at high temperatures mainly from the sticking and fusion of particles."

Jan 1, 2011