Search Documents

By M. B. Mesina

Mechanical separation systems are widely used nowadays for scrap metal processing, but they have natural limitations in product quality. The quality of the final product is considerably improved when sensors are used in the separation process. This paper describes new methods using sensors for scrap metal sorting and quality control. An example is the electromagnetic sensor, which uses the electrical and magnetic properties of materials to distinguish between different non-ferrous metals. The measurement results of two prototypes are reported. The benefits and the possibility to integrate such systems into practical applications regarding the processing of secondary raw materials are also described.

Jan 1, 2003

By Jesus Gonzalez

Peirce-Smith converters (PSC) are long cylindrical chemical reactors where copper matte reacts with air. Traditionally, air is injected laterally through submerged tuyeres at different subsonic velocities. However, the accumulated experience in steelmaking, particularly in the basic oxygen furnace (BOF) process, shows that the gas bottom injection may improve the mixing efficiency of a liquid pool. The aim of bottom injection is to maximize the copper kinetic energy meanwhile avoiding excessive reactor splashing. When gas is injected from a single orifice at the bottom of a liquid pool, two main gas flow regimes can be identified, bubbling and jetting. In this work, a PSC with bottom air injection is studied by means of multiphase 3D CFD numerical simulations considering multiple air velocities. Special attention is paid to the bubbles and jet formation mechanism. The mixing efficiency is measured by calculating the turbulent kinetic energy of the copper matte.

Jan 1, 2008

By Jae-Ho. Lee

For some electronic applications where a dispersed electrically-conductive particulate-phase is employed, the conductivity of the surface (or near-surface region) of the particles provides for the primary mechanism which determines its electrical conductivity. Particles of a less expensive material, which may have desirable thermal-expansion properties, when coated with silver offer a means of also obtaining desirable electrical properties and at low cost. The research conducted was focused primarily on the development of silver-coated tungsten particles for thick-film polymeric conductors. The ammoniacal electrolyte was formulated from silver-nitrate, glycine inhibitor and formaldehyde reductant. The reduction, and subsequent deposition, of silver occurred selectively on the surface of the tungsten particles. Coated particles were assessed by SEM imaging. The thickness of the silver coating was estimated to be approximately 100nm on the basis of a mass account and the coating being uniform. The electrical conductivity of a silver-coated tungsten-powder pellet was found to be similar to that of a silver-powder pellet, of identical geometry.

Jan 1, 1997

By Yuanyuan Wang, Hong Li, Xueting Liu, Hao Bai, Kang Zhou

"Phase change materials are widely used in efficient utilization of energy and new energy technology. Especially, more attention has been paid to composite phase material, which is applied on architectural energy-saving and efficient working fluid. In this paper, stearic acid-silicon dioxide composite material was prepared by sol-gel process from tetraethyl orthosilicate (TEOS) and stearic acid (SA). The material was investigated by Field emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectroscopy (FT-IR) and Differential scanning calorimeter (DSC). The FE-SEM results show that 3D-grids of silicon dioxide were formed clearly and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reactions between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity. This material is expected to be used to make a cooling working fluid.1. IntroductionEnergy thermal storage becomes increasingly prominent issue in recent years, because thermal storage has been used in many aspects, for example, it can be added into building materials to improve heat conditioning. Another potential application of thermal storage materials is that the intermittent waste heat can be collected and recycled effectively by using the thermal storage facility. Thus, energy thermal storage plays a significant role in conserving available energy and improving its utilization [1]. Energy thermal storage includes sensible heat storage and latent heat storage. The latent heat storage has great heat density with a constant temperature during the phase change process [2-5]. Large quantities of latent heat storage will be absorbed and released when phase change takes place. Based on the former researches, some phase change material (PCM), such as fatty acid and paraffin waxes, has been proved to have high latent heat storage capacity and appropriate thermal properties [5-6]. However, using the PCM in energy storage systems directly is restricted, e.g. some properties of organic PCM, like form-stability and thermal conductivity, are not good enough to use. Meanwhile, almost all the inorganic PCMs are corrosive and most materials may cause sub cooling and segregation [7-9].The other problem is that the leakage when the temperature reaches the phase change point. Therefore, encapsulated composite phase change material (CPCM) emerged in order to solve the problem of leaking out, minimize the sub cooling and prevent phase segregation. [10-13] However, the easy flammability of fatty acid also has hindered the development of PCM. Accordingly, it has been found out that silicon compounds are environmentally friendly promising substitutes for halogen-containing flame retardants. Especially, silsesquioxanes are excellent in the flame retardancy. So CPCM can be encapsulated with SiO2 acting supporting material."

Jan 1, 2014

By Du Sichen, S. Seetharaman, J. A. Bustnes

"The present study deals with the kinetic studies of reduction of some selected transition metal tungstates with hydrogen. The measurements were carried out by the isothermal thermogravimetric method. Shallow powder beds were employed in order to avoid the effects due to transport phenomena affecting the reaction rate. In this way, the chemical reaction rates could be selectively studied. The experiments were carried out in the temperature range 873 - 1173 K. From the experimental data, the activation energies were evaluated and were found to be around 88 kJ / mol in the case of both iron as well as cobalt tungstates indicating the similarities in W-O bonds in both cases. The activation energies obtained are discussed in the light of the position of the transition metal in the periodic table as well as the thermodynamic stabilities of the various tungstates.IntroductionThe tungsten containing hard metals, characterized by high density, belong to a class of two-phase metal matrix composites. While these types of materials have traditionally found their applications within the defence industry as armour-piercing projectiles, counterbalance in helicopters and military aircrafts, outer casings of hand-grenades, etc., commercial applications for this class of alloys also exist, including radiation shields, penetrators for the oil industry, turbines for turbo-jet engines and a wide range of sports related parts. A possible route to the production of these alloys is to reduce the tungstates such as FeW04, Co W04 and NiW04 using a reductant like hydrogen or carbon monoxide. In order to have a better understanding of the processes involved in the production, it is important to have a knowledge of the reduction kinetics for these tungstates. According to the knowledge of the present authors, while the reduction ofNiW04 by hydrogen gas has been investigated earlier in the present laboratorypl no systematic reduction study has been carried out previously for the tungstates of iron, cobalt."

Jan 1, 1996

By James O'Brien, Lyman Frost, Grant Hawkes, S. Elangovan, Manohar Sohal, J. S. Herring, Joseph Hartvigsen, Carl Stoots

"Pressing environmental and energy security concerns have brought much needed attention to economic production of hydrogen as the secondary energy carrier for non-electrical markets as well as to meet increasing demand for crude upgrading and desulfurization. While steam reforming of natural gas is currently the dominant method of hydrogen production, it is depleting a valuable fossil fuel while emitting green house gases. Thus, in the long run, efficient, environmentally friendly, and economic means of hydrogen production using nuclear and renewable energy needs to be developed. High temperature electrolysis using solid oxide electrolyte cells is an exceptionally efficient means of generation of high purity hydrogen. It is also capable of directly converting steam and CO2 into synthesis gas. This co-electrolysis process enables conversion of CO2 recovered from concentrated industrial sources into a feedstock for synthetic fuels production. Use of CO2 provides a means of storing hydrogen in a concentrated and convenient form – a hydrocarbon. This is also an effective storage medium for intermittent renewable energy sources such as wind and solar.Ceramatec, Inc and the Idaho National Laboratory are applying solid oxide fuel cell technology to the production of synthesis gas by high temperature co-electrolysis of steam and carbon dioxide. This technology utilizes solid oxide fuel cell stacks to electrochemically remove oxygen from steam and CO2, leaving a clean stream of hydrogen and carbon monoxide suitable for fuel synthesis. By varying the relative concentrations of carbon dioxide and steam, the hydrogen to carbon monoxide product ratio can be controlled as required by the desired type of synthetic fuel being produced from the syngas. The resultant synthesis gas has been used as the feedstock to produce synthetic methane and Fischer Tropsch liquid fuels.Alkaline and proton exchange membrane electrolysis cells typically operate below 100°C, while solid oxide electrolysis cells operates in the 750-850°C range. This higher temperature improves the efficiency significantly. Practically, it translates into a lower cell operating voltage, 1.1-1.4V for high temperature electrolysis vs. ~1.8V for water electrolysis. Hydrogen production is stoichiometric with current in all types of electrolyzers.Carbon dioxide is a valuable resource as a feedstock for energy storage as a hydrocarbon. There is a vast amount of renewable energy that cannot be effectively utilized as grid electricity, but which could be used to convert CO2 to hydrocarbons, offering a solution to the even more difficult (than supplying grid power) challenge of production of sustainable, domestic transportation fuels. Conventional electrolysis and chemical processes could be deployed to accomplish this conversion. However, high temperature co-electrolysis of CO2 and steam to produce synthesis gas using solid oxide fuel cell technology has the potential of improving the efficiency by nearly 50%. A domestic synfuel industry will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles while increasing our energy security."

Jan 1, 2010

By David R. Sadedin

The highly negative Gibbs free energies of hydrogen atom reactions suggest that refractory oxides such as titanium dioxide should be easily reduced by hydrogen atoms. These reactions appear to be most favourable at low temperatures; oxides should be reducible even at room temperature. Since hydrogen atoms are produced in plasmas containing hydrogen a number of investigators have used hydrogen plasmas of various sorts to test these possibilities for reducing refractory oxides, in particular TiO2. None of these attempts has succeeded, a small degree of reduction being achieved in only a thin layer near the surface. A deeper consideration shows that several factors complicate the reactions expected on the basis of the negative Gibbs free energy. One factor is that the back reaction by water molecules produces molecular hydrogen, not hydrogen atoms, and the metal atoms that have been reduced may be immediately re-oxidised. In plasmas there are complications due to diffusion, thermal and charge boundary layers and charged particle reactions. Interpreting the results of hydrogen atom reactions is difficult. Hydrogen is not detectable by electron dispersive spectroscopy and amorphous products are not determinable by x-ray diffraction. Another consideration is economics. The cost of producing hydrogen atoms has a large bearing on the metals for which hydrogen atom reduction may be competitive. In this paper these factors are discussed, some necessary basic studies are highlighted and the general principles of a laboratory reactor are given, together with the results of tests using ZnFe2O4, ZnO and TiO2 as test oxides.

Jan 1, 2006

By Serge Lavoie

Alcan's Guillaume-Tremblay plant, located in Jonquiere, Quebec, has been in operation since 1990. This was the first plasma dross processing plant ever built. In addition to the use of the plasma heating technology, Guillaume-Tremblay has other unique features making it a modern and efficient dross processing facility. This paper presents a general overview of the practical experience at the Guillaume-Tremblay plant. In particular, the utilization of plasma heating in industrial conditions, the metallurgical performance, the unique dross handling system, the control and information management system and the reclaiming of the by-products will be discussed. Finally, the use of the plasma process for salty dross will be addressed' briefly.

Jan 1, 1995

By Ehsan Khajeh

In this study, the permeabilities of Al-15.5wt%Cu and Al-19.5wt%Cu have been determined by solving the full Navier-Stokes equations on 3D geometries of interdendritic channels obtained by X-ray microtomography (XMT). The samples for XMT were sectioned from different positions in directionally solidified cylinders in order to obtain a variety of microstructures for each composition. The flow has been solved using a 2nd-order accurate Finite Volume Method (FVM) approach. The effect of employing uniform or unstructured mesh on the calculated permeability has been studied. The Marching-cube triangulation method was necessary to extract accurate surfaces for unstructured volume meshing. Calculated values of permeability for this range of solid fractions show partial agreement with previous experiments. Observed deviations are attributed to the difficulties of experimental permeability measurements.

Jan 1, 2009

By Paykan Safe

This paper reviews various process off-gas cooling options available for sulfide smelting processes. Advantages and disadvantages of each, system are discussed along with the selection criteria for a reliable and cost effective :system. Various systems are presented to demonstrate typical process parameters for smelter off-gas handling systems and to outline operating difficulties associated with each system:

Jan 1, 1998

By Bin Zhu, Mingmei Zhu, Hong Zhou, Xiaofei Dou, Bin Xie, Yu Wang, Tiancheng Lin

In this study, the formation of 2CaO·SiO2 and 3CaO·P2O5 solid solution (nC2S-C3P) in hot metal dephosphorization process is discussed. The variations of CaO and SiO2 mass, both in nC2S-C3P solid solution phase and liquid slag phase with increasing P2O5 mass in CaO-SiO2-FetO-P2O5 slags were calculated using Factsage software. CaO-SiO2-FeOt-P2O5 slag containing up to 18 % P2O5 was melted at 1823 K then cooled to 1673 K. The contents of CaO and SiO2 both in the solid solution phase and liquid slag phase of quenched samples were observed and analyzed by SEM/EDS. Both the calculated and experimental results show that the contents of CaO and SiO2 in the solid solution phase decreased, just opposite in the liquid slag phase, with increasing P2O5 content in the slags. Formation mechanism of nC2S-C3P solid solution in the slags was derived based on the ionic structure theory of molten slag. The SiO4 4- in the nC2S-C3P solid solution can be replaced by PO4 3- in the liquid phase resulting in the increasing of free Ca2+ and SiO4 4- in liquid phase.

Jan 1, 2015

By Yuanbo Zhang, Qian Li, Helei Zhang, Heng Yu, Guanghui Li, Tao Jiang

"Large reserves of specularite iron ores have been found all over the world, which is characterized by high total iron grade, low gangues content, as well as low commercial price. However, it has not been widely used in sinter or pellet production due to its inferior sintering and roasting behaviors. It has shown that the proportion of specularite ores was increased as high as 40%~50% and good results was achieveed by using Composite Agglomeration Process (CAP), an innovative agglomeration process invented by Central South University. But the mineralization of specularite is still unknown during composite agglomeration processing. In this paper, the induration characteristic of specularite ore is studied by simulating CAP in laboratory, as well as microstructure analysis of CAP product. The results show that specularite pellet is mainly indurated through recrystallization of Fe2O3, calcium ferrite within high basicity sinters matrix interweaves with the recrystallized Fe2O3 on the surface of the pellet, which forms an integral microstructure, and ensures high strength of CAP product for ironmaking.IntroductionLarge reserves of specularite iron ores have been found all over the world, especially in Minas Gerais of Brazil, Xuanhua city and Anshan city of China, Elba island of Italy, St.Gotthard of Switzerland, Cumberland of Britannic, and so on. The specularite ores have a smooth surface, as well as a good crystallization and dense texture. When specularite is used to produce pellets, the specularite ore grains are difficult to adhere onto green ball due to its poor ballability. Moreover, specularite pellet requires high roasting temperature over 1300°C [1]. When specularite ore is used in sintering, the permeability of sintering bed gets bad and the quality of sinter is diminished. The practice in a few sintering plants finds that the output and strength of sinter decrease with the increase of specularite proportion, and the consumption of coke increases [2-4]. Therefore, the utilization of specularite has been limited. Composite Agglomeration Process (CAP) is an innovative technology invented by Central South University [5-7]. The process has the following merits: making reasonable utilization of different iron ore resources; improving the quality and output of sinters; manufacturing sinters with low basicity; significantly reducing energy consumption, etc[8-9]. It has been shown that large proportion specularite ores, as high as 40%~50% can be used well by CAP [10], but the mineralization of specularite pellet is still unknown during composite agglomeration processing. In this investigation, the induration characteristics of specularite ore pellets is studied by simulating CAP in laboratory, and the phase composition and microstructure of CAP product are also characterized by using microscope and Leica image analyzer (Germany, Leica DM RXp)."

Jan 1, 2011

By Matthew John M. Krane, Christopher J. Vreeman, J. David Schloz

"A continuum mixture model of the direct chill casting process is used to model the transport phenomena and solidification behavior in the Direct Chill casting of an Al - 6 wt% Cu billet using Wagstaffs AirslipTM process. The model, which includes the transport of free-floating solid particles, can simulate the effect of a grain refiner on macrosegregation and fluid flow. Numerical predictions of sump profiles and composition and temperature fields are presented. Two 45 cm diameter billets were cast under production conditions with and without grain refiner. Temperature and composition measurements and sump profiles are compared to the numerical results. The comparison shows excellent agreement for the grain refined case. It is believed that an incorrect model assumption prevents good agreement in the non-grain refined billet. IntroductionDirect chill casting is a semi-continuous process in which molten aluminum enters the top of a water-cooled mold, is cooled, and forms a solid ingot drawn out below (Figure l(b)). The molten aluminum begins to solidify due to the cooling effect of the mold wall. As the ingot is withdrawn from the bottom of the mold, water jets impinge on the surface, directly cooling the billet and forming a solid layer around a liquid melt, commonly referred to as the sump.A particular defect that occurs in a wide range of casting processes, including the direct chill (DC) casting of aluminum alloys, is macrosegregation, the uncontrolled redistribution of alloying elements on the scale of the ingot during solidification. Macrosegregation in DC cast ingots can produce non-uniform mechanical properties [l], which affects the behavior of the metal during downstream forming and heat treat operations."

Jan 1, 2001

By Anna Wasilkowska

The study concentrates on the effects exerted by microstructure, deformation history and uniaxial stress conditions (temperature, stress state, strain rate) on the mechanical properties offerritic TRIP-aided steels for automotive applications. In low-alloyed TRIP-steels it is quite difficult to separate the effect of the austenite to martensite phase transformation from the influence of the ferritic matrix contributing to the yield stress and uniform elongation. Investigation of transformation kinetics of retained austenite as a function of the deformation temperature show that using the parameter k to characterize the retained austenite stability allows to identify regious of different temperature sensitivity separated by a transition temperature of 10±5°C. The observed low strain-rate sensitivity of the flow stress is an intrinsic property of the ferritix matrix and points to defomtation governed by slip. The ultimate tensile strength is much stronger affected by temperature than the yield stress. The influence of the temperature on the elongation is complex, because of the heating of the specimens by 60-l20°C at moderate and high strain rates. The increase of the total strain can be understood in terms of thermal softening of the ferrite. On the other hand, the steep increase of the stress during dynamic testing is an effect of accommodated elastic and plastic strains in the matrix. The strain- hardening exponent is dependent on the conditions imposed during testing. The martensite transfomtation rate is lower and the critical stress for martensite nucleation is much higher under compression compared to tensile loading. In secondary tensile tests, the yield stress increases steeply, and the ultimate tensile strength and the total elongation depend linearly on the amount of pre-straining. The results confirm that in the range of 8=10-4 s-l the TRIP-effect governs room temperature plasticity. Keywords: TRIP-steels, mechanical properties, strain rate sensitivity, temperature sensitivity, austenite stability

Jan 1, 2003

By D. Van Dooren

The final goal of the research project is to develop a 3D FEM model that is able to predict the kinetics and micro-structural evolution during the bainitic transformation. The input parameters consist of thermodynamic and atomic mobility data obtained from the ThermoCalc and mCTRA databases combined with structural mechanics data extracted from the stress-strain curves of the fcc and bee phases. In this paper the general principles of the model are outlined and some interesting preliminary results are shown and commented. The full implementation of the model has presently not been achieved yet. In the model the bainitic transformation is considered as a sequence of martensitic (re)nucleation and growth of a ferritic subunit followed by the carbon rejection into the surrounding austenite. The (re)nucleation of the subunits will be described through a non-classical martensitic nucleation criterion. Once a nucleus has been activated at a specific location in the material, a full-sized subunit is instantaneously formed through a displacive mechanism. The stress state in the system that arises due to the transformation strain can be calculated by a 3D FEM programming code. Immediately after the formation of the subunit, another 3D FEM programming code calculates the carbon diffusion from the supersaturated ferrite into the surrounding austenite. The resulting stress state and carbon profiles will be used to determine where and when a new subunit will nucleate based on a renucleation criterion. Keywords: Bainitic Transformation, Modeling, Eshelby, Carbon Diffusion

Jan 1, 2003

By J. W. Matousek

Copper losses in smelter slags are :typically normalized with some form of the distribution coefficient, written as the ratio of the weight percent assays of metal in slag to the metal in matte or its inverse: L(s/m) = %(Cu)/%[Cu] or L(m/s) = %[Cu]/%(Cu) However, this simple approach ignores the dynamics of the smelting process. It overlooks the effect of the chemical work done in producing a given matte grade from concentrates of different grades -- or from a single concentrate blended with varying quantities of copper bearing precipitates or reverts. This paper examines the combined influences of matte grade and the work done in smelting on the copper content of smelting furnace slags. A simple model for the relationship is proposed.

Jan 1, 1999

By J. P. Gu, C. Beckermann

"Melt convection and macrosegregation in casting of a large steel ingot is numerically simulated. The simulation is based on a previously developed model for multicomponent steel solidification with melt convection, and involves the solution of fully coupled conservation equations for the transport phenomena in the liquid, mush, and solid. Heat transfer in the mold and insulation materials, as well as the formation of a shrinkage cavity at the top are taken into account. The numerical results show the evolution of the temperature, melt velocity, and species concentration fields during solidification. The predicted variation of the macrosegregation of carbon and sulfur along the vertical centerline is compared with measurements from an industrial steel ingot that was sectioned and analyzed. Although generally good agreement is obtained, the neglect of sedimentation of free equiaxed grains prevents the prediction of the zone of negative macrosegregation observed in the lower part of the ingot. It is also shown that the inclusion of the shrinkage cavity at the top is important in obtaining good agreement between the predictions and measurements.IntroductionMacrosegregation in large steel ingots is one of the most well-known and now classical problems in the field of solidification and casting [1]. Commonly found macrosegregation patterns in steel ingots are a positively segregated zone at the top, negative segregation near the bottom in the equiaxed zone, inverse segregation near the ingot surface, V-segregates along the centerline, and A-segregates in the columnar zone [2, 3]. It is well established that the macroscopic transport of species leading to macrosegregation can occur by a variety of mechanisms, including thermally and solutally driven natural convection of the melt in the mushy zone, flow due to solidification contraction, and the sedimentation of free equiaxed crystals. Fredriksson and coworkers [ 4,5] provide recent overviews of the solidification transport phenomena and macrosegregation in ingot casting."

Jan 1, 1999

A simulation of a capper concentrate smelter was built with a capacity of 450,000 tons per year. The system's components to simulate were three : a Reverbetory furnace, a Wiente ' s modified converter ( TMC ) and two cranes. The system was classified as dynamic, stochastic and discrete. In the simulation language choice it was concluded that the most advantageous one was GPSS/H. The model verification was done through the interactive Debugger that the language has and the statistical validation was done through the result variables of sane activities, that as a whole characterize the system (charged matte and charged concentrate to the TMC, skimming white metal and skimning slag). The validation was done comparing the simulation results of these variables with the ones obtained for those variables in a specific month in the smelter. The comparison consisted in a difference of means test and in all cases the equality was accepted with a 95% of confidence. The animation tool was PROOF, a general purpose animator, that is used after processing the simulation.

Jan 1, 1994

By J. E. Allen

The trend in refractory technology for the copper and nickel industries has been to higher quality raw materials and improved processing technology. These changes have been dictated by the changes in pyrometallurgical processes in these industries. For example the introduction of flash smelting, reaction type smelting and auxiliary slag cleaning furnaces havedemanded better refractories materials. Extensive field applications and improved laboratory testing procedures have helped make this transition possible. Changes in refractory technology, primarily in basic refractories, are followed from the late fifties to the present and into the future.

Jan 1, 1994

By G. G. Richards

The zinc slag fuming process is used to recover zinc from molten iron-calcium silicate slags by treatment with pulverized coal and air. The rate of zinc fuming is controlled by the complex interaction of several kinetic factors including the rate of entrainment of coal in the slag, the extent of the coal-slag reaction and the rate of ferrous oxide oxidation to ferric oxide. This paper briefly outlines the mechanism of fuming and, on this basis, optimization of process parameters is discussed. Modelling analysis and recent industrial trials at Cominco show that coal entrainment in the slag, bath temperature, and bath depth are critical variables affecting process rate and efficiency. The first step in process optimization is to assess coal bypass of the bath. In general, changes which promote operation at a higher temperature, greater coal entrainment in the slag and extended residence time of the coal in the bath increase fuming performance. Coal entrainment is controlled by injection conditions whereas bath temperature is a function of coal combustion and ferrous oxide oxidation. Residence time of the coal is largely a function of bath depth. The implication of model predictions for continuous fuming is shown.

Jan 1, 1994