Search Documents

By Nobuyuki Higashiyama, Ikuo Yonezu

"Hydrogen-absorbing alloys containing rare-earth elements are used in high capacity nickel-metal hydride secondary batteries,' hydrogen storage systems for portable fuel cells, and refrigeration systems. New hydrogen-absorbing alloys containing rare-earth elements have also been developed and introduced into these applications. High performance in nickel-metal hydride secondary batteries is strongly demanded because of the remarkable advancements in portable electric appliances. A large hydrogen absorption capacity, high electrochemical reactivity and superior corrosion resistance in an alkaline solution are required for hydrogen-absorbing alloys used in nickel-metal hydride batteries. The aim of this investigation is to improve the performance of conventional LaNi5 type hydrogen-absorbing alloys. For example, Mm(Ni-Co-Al-Mn)„ type hydrogen-absorbing alloys with various non-stoichiometric compositions were developed. In addition, a new process of rapid quenching process was applied for preparing these hydrogen-absorbing alloys in order to improve their performance.IntroductionRecently, the trend in electronic appliances toward portability has increased the demand for high capacity of secondary batteries as power sources. Since nickel-metal hydride batteries were first commercialized in 1990 in Japan, they have become increasingly popular as power sources for cellular phones, portable computers, electric shavers, and other, products.The performance of a nickel-metal hydride battery, such as its discharge capacity, high rate capability, and charge-discharge cycle life, strongly depends on the characteristics of the hydrogen-absorbing alloy negative electrode. Many types of hydrogen-absorbing alloys have been developed so far. For a hydrogen absorbing alloy to be used as the negative electrode material, (1) it must allow a large amount of hydrogen to be absorbed and desorbed in an alkaline solution, (2) its reaction rate should be high, and. (3) it must have long term durability under repeated charge-discharge cycling. However, LaNi5, a typical rare earth-nickel type alloy, shows significant capacity deterioration during repeated charge-discharge cycling. Therefore the first step in its development was to obtain sufficient corrosion resistance of the LaNi5 alloy for its use as an electrode material. A partial replacement of nickel with cobalt and a substitution of the lanthanum- content with misch metal (Mm), a mixture of rare earth elements such as lanthanum, cerium, praseodymium and neodymium, were very useful in improving the charge-discharge cycle life. However, the discharge capacity of the alloy was still not sufficient for a practical battery. A study of the effect of the partial substitution of aluminum and manganese showed that the best alloy composition was Mm(Ni-Co-Al-Mn)x, as follows.The stoichiometry x of Mm(Ni-Co-Al-Mn)x largely affects the discharge capacity and cycle life. Theose alloys with non-stoichiometric alloys with the compositions of [Mm(Ni-Co-AMn)x: 4.7<x<4.8] have a large capacity and a long cycle life. Nogami' et al. reported that 'a non-stoichiometric alloy with a Mm(Ni-Co-Al-Mn)x (x=4.76) composition showed approximately 10% higher discharge capacity than the stoichiometric alloy (x=5) [1] and greater influence of x on the electrochemical properties of multi-component AB„ type hydrogen-absorbing alloys for batteries."

Jan 1, 2000

By T. Tamagawa

Vaporization of zinc and mixing of zinc vapor with CO-CO2 mixtures were studied experimentally to prepare Zn(g)-CO-CO2-Ar mixtures with desired composition for investigating the condensation behavior and efficiency of zinc vapor. The vaporization rate of zinc was generally constant under given conditions, and could be increased by raising the flow rate of the carrier gas, temperature and vaporization area. The Zn(g)-CO-CO,,-Ar mixtures were quenched by a water-cooling sampling tube for measuring the actual composition of the mixtures in the reactor. The oxidation extent of the zinc vapor in the CO-CO2 mixtures had relation to the CO2/CO ratios and the temperatures. Under current conditions, it was necessary to employ the CO2/CO ratio below 0.125 for mixing the zinc vapor with CO-CO2 mixtures without oxidation. In addition, the appearances and zinc contents of the condensed zinc on the sampling tube were also examined.

Jan 1, 2001

By M. Cowling, S. Kumarl, A. W. Piper, R. A. Forsdick, C. Bailei, M. Patell

"The lead-refining process takes place in hemispherical vessels called kettles. In these kettles, lead-bullion is mixed at a certain temperature to remove impurities from the melt. This paper presents steps in a novel method for calculating vortex shape and flow field in the refining kettle using Computational Fluid Dynamics (CFD). First of all a two-dimensional axisymmetric model is used to calculate the vortex shape at the liquid-air interface. Here action of impellers and baffles are accounted for by adding source and sink terms to the appropriate momentum equations. The model includes Yolume of Fluid (YOF) method to predict the shape of interface deformation, i.e. vortex. This strategy reduces the computationally intensive three-dimensional transient simulations to a more efficient two-dimensional model. The calculated vortex shape is then used to regenerate a full three-dimensional grid. This grid is used to carry out steady-state simulation using the standard multiple-reference-frame method of impeller-fluid-baffle interaction within the commercial code Fluent. Simulation results for both stages of the development are compared with experimental data.IntroductionOne of the most important steps in Lead Refining process is impeller stirred mixing of Lead Bullion in hemispherical vessels. During this process, the melt is treated with one or more reagents in order to remove impurity elements such as copper, antimony, silver and bismuth. These impurities react selectively with the reagents and float to the melt surface in the form of a powdery layer, which is then skimmed for further processing. Figure-! shows (a) the lead refining kettle and (b) the schematic representation of involved flow pattern. Stirring of the lead bath using specific impeller designs, which creates a central vortex, provides a mechanism for draw-down and dispersion of the buoyant reactants. Clearly, effective control of the impeller generated vortex and flow pattern is crucial to achieving efficient operating conditions."

Jan 1, 2001

By Miller, Geoffrey W.

The Ravensthorpe Nickel Project (RNP) flow sheet provides for the upgrading of Ni & Co in a size based beneficiation process prior to leaching. The upgrading effect on Ni and Co makes the beneticiation process a powerful addition to the flow sheet. Multiple linear regression (MLR) analysis based on 351 individual batch tests, 52 large scale composites and 21 pilot plant tests has been used to successfully model beneticiation product grade, recovery, upgrade and mass recovery. Statistically, 83% and 96% of the variability in nickel recovery and nickel product grade respectively was accounted for. Algorithms have been developed for Ni, Co, Mg, Al and Fe, which represents the revenue and operating cost factors for the process. The algorithms have subsequently been applied to the resource model, allowing prediction of elemental grade and recovery for the development of the mine schedules based upon these parameters and not head grades alone. This has allowed optimisation of the mine schedule for improvement to the project&apos;s NPV. Keywords: Ni Laterite, Prediction, Multiple Linear Regression, Beneficiation

Jan 1, 2004

The copper concentrate market is becoming increasingly unstable. In the early 1990s large concentrate stocks were built up and the glut was cleared only after treatment charges rose so sharply that &apos;non-traditional&apos; custom smelter capacity, such as in Kazakhstan, could be employed, By 1994 the market had shifted and Western smelters were unable to secure enough concentrates to operate full out. The reason for these sharp swings in the market balance is that virtllally all the recent mine development has been non-integrated. With different companies developing new mine . and smelter capacity, it is inevitable that the pace of expansion in the two sectors will not be coordinated. For many years the Japanese smelters were the major buyers from the new mm-integrated mines. However, Japanese smelter capacity is unlikely to increase appreciably in the future and this stabilizing influence will be very difficult to replace. This paper will examine the likely concentrate/smelter balance over the next five years and will forecast the likely direction of? treatment charges. It will also touch on the critical variables in assessing the viability of new greenfield custom smelter capacity, such as proximity to concentrate sources, by-product sulfuric acid prices and, most importantly, tariff protection.

Jan 1, 1995

By Shengli Wu, Mingyin Kou, Laixin Wang, Xinliang Liu, Zhennan Qi, Yujue Wang

Softening and melting experiments were conducted on four kinds of imported lump ores named A-D, under different temperature intervals within the self-developed visualization high temperature furnace. By calculating the reduction and shrinking degree under different intervals, softening and melting indexes were determined. These ores all expanded firstly followed by shrinkage with the temperature increasing. The difference of lump ore’s own characteristic led to different softening and melting behavior. The results showed that the looser the structure was, the better the reducibility will be. The compact structure and good reducibility led to high expansion rate. The beginning softening temperature declined and the ending softening temperature increased because of high porosity, which resulted in wide softening temperature interval. The charging ratio of lump ore A should be improved. Lump ore B should be distributed in the center of the blast furnace. Lump ores C and D should be used less.

Jan 1, 2016

By L. Katgerman, R. Van Toi, H. E. A. Van den Akker

"Mould filling simulations are powerful tools for optimizing the characteristics of castings. The robustness of calculational methods for mould filling simulations is generally tested in simple geometries. While a vertical plate has been used often for validation studies, this paper aims at mould filling simulations of a horizontal thin wall casting. Such castings exhibit a strong interaction between heat transfer (solidification), surface tension and gravitational force.The results are presented of a study to validate numerical simulations of mould filling phenomena in a thin wall horizontal casting. Solidification during mould filling is studied computationally. Velocities are measured using Particle Image Velocimetry.INTRODUCTIONIn foundry practice Computational Fluid Dynamics (CFD) is being considered a promising tool to arrive at a better understanding of casting defects introduced during the mould filling period of a casting. The use of CFD is believed to be advantageous in predicting possible defect locations, pouring times, and the lowest possible casting temperature without the risk of cold shuts. In addition, CFD may be used to optimize pouring system geometries [1,2]. As opposed to experimental studies in, e.g., cold water models, CFD allows for the flexible modification of the casting geometry and the pouring system, and for the inclusion of physical effects such as solidification and heat transfer. Thus, a proper use of CFD may lead to a reduction of the casting rejection rate without expensive trial-and-error procedures, and to a decrease of production costs in foundries. Mould filling simulations take a special place in CFD, because a free surface tracking algorithm is required. Over the past decade methods, MAC [3] and SOLAVOF [4], have been extended to 3-D. The robustness of computational methods for mould filling simulations is generally tested in simple geometries [5,6]. While a vertical plate has been used often for validation studies, this paper concentrates at mould filling simulations of a horizontal thin wall casting. Thin wall horizontal castings exhibit a strong interaction between heat transfer (solidification), surfaces tension and gravitational force. The gravitational force in this setting is orthogonal to the plane of flow and has therefore no influence on the shape of the free surface in the plane of flow. Mould filling numerical methods and algorithms have been recently reviewed by Chen et al.[7]."

Jan 1, 1999

By S. P. Rivers

The stainless steel industry re1ies on nitric-hydrofluoric acid (HNO,/HF) pickling solutions to remove surface contaminants and maintain the corrosion resistance of the steel. More stringent environmental guide1ines are expected to be placed on the disposal of these solutions which could significantly increase processing costs. The U.S. Bureau of Mines has been conducting research to develop a process for recycling depleted pickling solutions, thus reducing the quantity of by product acids generated. Research has shown that F- can be liberated from the predominant iron fluoride species (FeF,&apos;) by using oxalic acid in an electrodialysis cell. Ion selective membranes allow dissolved metals in the depleted solution to be replaced with hydronium ions by metathesis, thereby regenerating the HF. The regenerated HN03/HF is then retained in the pick1ing solution. This paper reports on the research effort at the U.S. Bureau of Mines Rolla Research Center to apply electrodialytic recycling to HN03/HF pickling solutions.

Jan 1, 1993

By G. Roy Chaudhury

Adsorption techniques are comparatively low cost and effective for treatment of arsenic contaminated drinking water. Various adsorbents such as alumina, ferrihydrite and manganese ores have been used, but there has been little investigation of modifying the structure of ferrihydrite to improve its adsorptive efficiency of As(III) and As(V). In the present study the incorporation of manganese oxide into the ferrihydrite structure was carried out and the prepared materials used in arsenic adsorption experiments. The compounds were X-ray amorphous, but TGA/DTA and FTIR analysis showed some structural characteristics. Sorption studies reported in this paper indicate the excellent arsenic removal properties of the manganese/iron compounds with a loading capacity of 0.3 mmol/g. Adsorption follows first order kinetics and the results fitted to adsorption and mass transfer models. Arsenic levels in water containing 1 mg/L As(V) were reduced by 50% in 20 minutes and 90% in 60 minutes using 1 g/L manganic ferric oxyhydroxide.

Jan 1, 2003

By Tabbetha A. Dobbins

We report studies concerning the time frame for catalytic reactions between NaAlH4 (sodium alanate) and TiCl3 during high energy milling. Spectral features in x-ray absorption spectra were analyzed for samples milled for various times (0 minutes, 1 minute, 5 minutes, 25 minutes, and 125 minutes). A structural transition from Ti3+ to Ti0 is observed within the first 5 minutes of milling. The Ti0 structure persists for samples milled for times longer than 5 minutes?even after those samples underwent a subsequent single hydrogen desorption/absorption cycle. Samples milled for less than 5 minutes retain Ti3+. For samples milled for 1 minute, the Ti-K edge position shifts from Ti3+ to Ti0 after a single desorption/absorption cycle. However, the first coordination sphere around the Ti0 absorber occurs at longer distances for 1 minute milled sample. These results hint at the formation of Ti0 pure metallic clusters upon desorption/adsorption cycling of 1 minute milled sample. Previously reported x-ray absorption spectroscopy studies have demonstrated the structural transition from Ti3+ (in TiCl3) to Ti0(determined to be TiAl3 found at the surface of the alanate powder). Aluminum deficiency on the NaAlH4 lattice is responsible for controlling hydrogen absorption capacity. These time-resolved spectroscopy studies suggest the possibility for controlling aluminum deficiency, while still maintaining titanium activation of the alanate powder, by manipulating the coordination environment of the titanium dopant during the first five minutes of high energy milling. Specifically, a possible approach to mitigating aluminum deficiency during doping would be to introduce an alternative species to which the to Ti3+ catalyst would form a metallic bond after the TiCl3 has attached at the surface of the sodium alanate powder and before the Ti3+ forms the TiAl3 intermetallic species.

Jan 1, 2006

By Robert Fritzsch, Ragnhild E. Aune, Mark William Kennedy, Behzad Mirzaei

"The quantitative particle concentration can give important information about the cleanliness of melts for quality control in primary and secondary production of aluminum. Manual quantification of the particle concentration is normally a time consuming process and human control can bias the acquired images and particle count.The present paper explains the automated image-processing steps for the quantification of SiC-particles, with equivalent diameters from 2 to 25 µm, in solidified A356. A total of 700 micrographs, acquired with a standard white light microscope with 10 x magnification, were analyzed. The applied software (Image Pro-Plus 7.0 from MediaCybemetics®) allows for programming of macros which in tum provides the user with a higher degree of control. The automated results are compared with the results obtained by manually counting the particles in the same micrographs. The impact of the automated results on the estimated filtration efficiency was established to be only -3%.IntroductionInclusions are both indigenous and exogenous particulates that are present in commercial metals such as aluminum. If large individual or large numbers of inclusions are present, they can have a significant negative impact on the appearance, mechanical and chemical behavior of products produced from the metal. Aluminum is known to contain large numbers of inclusions: =50 µm in size, e.g. typically <l ppm by volume or <100,000 inclusions of>20 µm per kg of metal as detectable using a Liquid Metal Cleanliness Analyzer, LiMCA [1]. Depending on the final application of the aluminum, inclusions can render the metal 'not fit for purpose', and result in serious economic consequences to metal producers.It is not surprising that the aluminum industry has developed a number of treatment processes to improve metal cleanliness, given the large number of high value products whose quality can be adversely affected by inclusions. CFFs are the most commonly applied filtration process and have been used to filter >50% of the world production of aluminum since the 1990's [2].Inclusions in aluminum may be particles, bifilms [3] or clusters of: oxides (Al2O3 , SiO2), spinels (MgO· Al2O3), carbides (SiC, Al4C3), nitrides (AlN), borides (TiB2), sulfides, phosphides and intermetallics [ 4]."

Jan 1, 2013

By V. V. Geikhman

The paper updates the Plant experience in the development and implementation of an advanced environmentally friendly zinc production technology complying with the technological and economic level of producers in the world and the standards of maximum permissible gas emissions stipulated by the Russian legislation. General water recycling engineering allowed to ensure 95.6% water rotation level. All solid wastes formed during treating zinc concentrate are processed into marketable products or semiproducts and sold. As a result of implementing innovation techniques production at the Chelyabinsk Zinc Plant is non-waste.

Jan 1, 2006

By Stephen M. Testa

Several methodologies are available for the remediation of contaminated soils including bioremediation, vapor extraction, chemical fixation, incineration and direct disposal. A proven innovative and cost effective alternative for the fixation of contaminated soils is via cold-mix Environmentally Processed Asphaltm (EPA"&apos;). EPAm methodology utilizes contaminated soil as an ingredient in an industrial process to produce a commercially viable product. Petroleum hydrocarbon and metal affected soil is incorporated with a water-based asphalt emulsion and varying amounts of aggregate to produce a range of cold-mix asphaltic products that fulfills the requirements of a variety of end uses. This viable and creative use which is within the intent and spirit of current regulations in producing, in lieu of a landfill waste, an end product for use as a berm, road base, liner, or other site specific application. Consideration of certain engineering and environmental factors including durability, stability, chemical resistance and ageing, biological resistance, permeability, leachability and geochemical aspects suggests that cold-mix asphalt incorporation of affected soil will perform more than adequately under normal conditions for a long period of time.

Jan 1, 1994

By A. G. Cecutti

A brief overview of the known significant health effects of both Nickel and Cobalt will be presented. Some time will be given to the current research activities, especially for Nickel. Emphasis will be placed on some of the controversial issues associated with their health effects.

Jan 1, 1988

By S. C. Grand, T. J. Auping, K. Born

Process control, environmental monitoring, budgeting and accounting are based on process data. Without appropriate tools for data analysis, the process data could remain unused and wasted. This paper demonstrates how data reconciliation can be used as a tool to develop closed mass balances. Mass balances are the initial step in plant optimisation (technical, economical or environmental). From mass balances, fundamental process models can be developed. These balances link process parameters (e.g., feed materials) to process performance (e.g., recovery of valuable elements). Some of these models could find their way into simulators useful to plant operators. Classical regression methods regularly fail when they are applied to complex non-linear problems involving a large number of variables. Alternatively, multiparametrical regression analysis can be successfully applied with the aid of neural networks based on reconciled data. Both methods have been applied to plant data originating from the hydrometallurgical zinc plant at Ruhr-Zink, which in this paper serves as a case study. Very promising and useful results were obtained from this study.

Jan 1, 2000

By Wang Haibei

China is the important country in terms of Ga, Ge reserves and products. These elements usually associate with lead and zinc ores such as in Fankou, Dachang and Lanping mines. Until now these metals could not be extracted from zinc residues effectively. The main reason is that it is difficult to separate zinc and iron. BGRIMM has carried out considerable research on this subject and some hydrometallurgical processes were developed. Zinc residues were pressure leached with a reducing agent such as zinc concentrates or SO2 at 110~130C. The final concentrate of H2SO4 was 30~50g/L. The metals such as Zn, Fe, Ga and Ge were dissolved into solution. In the leaching residue Pb and Ag could reach 20% and 2000g/t. The feed of solvent extraction was prepared from the leaching solution by pre-neutralization ? precipitation of Ga, Ge and acid dissolving. Then Ga and Ge were extracted by solvent extraction through P204 and G315 produced by BGRIMM. After stripping, metallic Ga was produced by electrowinning. GeO2 was produced by precipitation. The iron in raffinate was removed by the hematite process. The solution after removal of iron came back at the zinc neutral leaching stage. In 2003-2004, pilot tests were finished in BGRIMM in cooperation with Fankou Lead and Zinc Mine Ltd. And the extraction rate of Ga and Ge in the leaching stage was 94% and 83% respectively. The total recovery rate was 90% and 80%. It is estimated that the technology has a wide commercial use in the coming five years.

Jan 1, 2006

By H. Masuda

The lijima Zinc Refinery started operation in 1972, and has today an annual capacity of 200,000t-Zn. The hematite process was employed for the first time and the ideal of waste-free refinery has been pursued for 30 years. In recent years, however, only half of the hematite produced would be sold to the cement industry and hence a reduction of arsenic level has been necessary in order to sell the entire amount produced. The arsenic cementation process with zinc powder, developed through a long time laboratory research was found among some options as the best for the hematite process. The construction work started in 2000 and the facility was put into operation in 2001, As a result in the same year all hematite were sold to the cement industry. The outline of this project, present operations and technical issue are reported in this paper.

Jan 1, 2003

By A. Erçin Ersundu

In the present work, three different domestic iron ores; Sivas Divrigi B Head high grade hematite lump ore, Malatya-Hekimhan-Hasançelebi medium and low grade magnetite lump ores reduced with Soma-Kisrakdere lignite coal to investigate their suitability for sponge iron production. A laboratory scale box furnace was used to carry out the reduction experiments. In the experimental studies different operation parameters were selected being Cfix/Fetot. ratio, temperature in the range of 1100 - 1250 oC and time, to determine their effects on metallization. Metallization degree up to 90 % was found in the reduction experiments realized by using Sivas Divrigi B Head high grade hematite lump ore, whereas for Malatya-Hekimhan-Hasançelebi medium and low grade magnetite lump ores 60 - 65 % metallization degrees were obtained.

Jan 1, 2008

By G. W. Barton

Process Systems Engineering (PSE) can be defined as the integrated usage of computer-based design and analysis tools. As such, PSE is becoming increasingly important in the chemical and petrochemical industries. This paper shows how a range of PSE techniques have been applied to the zinc electrowinning process. Topics discussed include model development, parameter estimation, steady-state and dynamic model applications, steady-state optimisation and neural network modelling.

Jan 1, 1994

By Bo Björkman

Four different arsenic containing dusts from the Boliden plant, Boliden mineral AB, Sweden have been examined. A kinetic study of the As elimination was performed in a laboratory scale roasting furnace for roasting furnace ESP dust and smelting furnace ESP dust. Characterisation and thermodynamic calculations were carried out to determine the mineralogy, and the stability of compounds in the dusts studied. The characterisation methods used were chemical analysis, X-ray diffraction analysis and microprobe analysis. It was found in the experiments that a high degree of As elimination was obtained for roasting fumace ESP dust and a low degree for smelting fumace ESP dust. Derived kinetic models are given. A prediction of the As-elimation for settling furnace dust and converter ventilation dust is presented.

Jan 1, 1994