Search Documents

By D. M. Hausen

Applications of process mineralogy to the exploitation of molybdenum ores begins with early exploration and continues through the evaluation of mineralized prospects, to amenability testwork and pilot plant studies, to the development of a mineable orebody and to the development of a viable process for recovery. After plant construction, a broad range of products from a wide selection of sampling locations, i.e. grinding circuit, flotation cells, smelters and roasting kilns. etc., are evaluated analytically and microscopically, followed by periodic troubleshooting of problem points. The various crystalline phases of molybdenum that occur naturally and throughout various hydrometallurgical and pyrometal1urgica1 processes are identified and characterized by a variety of instrumental methods, including XRD-XRF, optical and electron microscopy, infrared spectrographic and differential thermal analysis.

Jan 1, 1989

By Lifeng Zhang

Printed circuited boards contain considerable quantities of valuable metal, while also containing many environmental pollutants making them unsuitable for landfill. In this study the decomposition of common plastics used in printed circuit boards were studied. Polytetrafluoroethylene (PTFE), polyvinyl chloride (PVC) and polyethylene (PE) were heated in both C02 and argon atmospheres using a thermo-gravimetric furnace (TG) coupled to a mass spectrometer (MS). Soda ash Na2C03 and baking soda NaHC03 were used as reactants. The degradation temperatures and evolved gases are presented for single plastics and mixtures. Mixed plastics are shown to behave as a sum of the individual plastics. The mass loss temperature is the same in CO2 and argon. However, less residue is formed when heated in CO2.

Jan 1, 2008

By Filippos Patsiogiannis

Laboratory size (4.5 kg) low carbon steel melts were deoxidized using Al and FeAl (33% Al), with and without synthetic fluxes, in alumina and zirconia crucibles. The dissolved oxygen, total oxygen, soluble aluminum, insoluble aluminum, silicon and carbon contents in the melt were determined as a function of refining time and temperature. It was observed that the reaction between aluminum and oxygen in solution closely follows thermodynamic equilibrium. Silica present in the alumina crucibles was found to be a source of oxygen for the melt, while this was not the case for zirconia crucibles. Reoxidation of the melt occurred through oxygen pick-up from the atmosphere. The extent of this reoxidation was found to be a function of oxygen content of the bath and the slag cover on the surface of the melt. The effectiveness of calcium-aluminate based fluxes in protecting the melt from the reoxidation and in increasing the rate of removal of inclusions was evaluated.

Jan 1, 1992

By Günter Petzow, Hans Leo Lukas, Hans Jürgen Seifert

"The CALPHAD method (CALculation of PHAse Diagrams) has been extensively developed in the last 25 years and became a useful tool in materials science. Thermodynamic descriptions for the functions of state of unary, binary and ternary phases are derived by the optimization of phase diagrams. These functions are stored in computerized thermochemical databases and can be combined to extrapolate to multi component systems. Depending on special demand, the actually most advantagous presentations of the calculated results can be chosen: tables or in a clear graphical form as phase diagrams, phase amount diagrams or volatility diagrams. The method will be desribed by the system Ti-Si-C-N-O including the ceramic subsystem Si3N4-SiC-TiCi,N1_1,-C-N-O which is very important for the development of ceramic composites. The calculations give the thermodynamic stabilities of the condensed phases as function of temperature, concentration and partial pressure of different gas species. Adjusting the sintering conditions to these results the formation of unfavourable compounds or liquid phases can be suppressed.IntroductionThe CALculation of PHAse Diagrams (CALPHAD-method) of multicomponent systems provides the possibility to plan experiments very efficiently and avoid the experimental trial and error approach for the development of materials. The main problem for best use of calculated results is their interpretation with regard to the specific applications under consideration. Tables give the exact quantitative data for the treated phenomena. However, most important to make best use of these thermodynamic data is their graphical representation especially designed for the solution of specific problems, scientific as well as application oriented. Only well chosen graphical representations support a comprehensive understanding of the thermodynamic interrelationships and the transfer to the problem."

Jan 1, 1996

By A. V. Reddy, C. Beckermann

"The DC continuous casting of a grain refined AI-4.5%Cu round ingot with realistic boundary conditions is numerically simulated. Of particular interest are the effects of the transport of free solid in the form of equiaxed grains on the macro segregation patterns and the final grain size distribution. The study uses a previously developed two-phase model that incorporates descriptions of heat transfer, solute redistribution, melt convection, and solid transport on the system scale with microscopic models of solutal undercooling, microsegregation and grain impingement. The numerical results indicate that grain transport inhibits the formation of inverse segregation in the ingot shell and promotes negative centerline segregation. This is explained by the reduction in the solid coherency next to the mold and the advection of solute-lean grains towards the centerline. Comparisons with the experiments of Finn et al. [5] illustrate the need for considerable improvements in the model. IntroductionMacrosegregation continues to be one of the concerns in DC continuous casting of aluminum ingots. The variation in composition over the ingot cross section results in the need to adjust alloy composition in order to meet mechanical property specifications in finished products. The extent of macrosegregation is greatly affected by the casting conditions, such as casting speed, superheat, cooling rate, mold size, alloy composition, and grain refining practices. Thus, it is of great interest to develop a comprehensive mathematical model to simulate the casting process, enabling the selection of conditions that minimize macrosegregation while maintaining a high productivity."

Jan 1, 1994

By Alwin Frei, Aldo Steinfeld, Peter G. Loutzenhiser, Enrico Guglielmini

"Using concentrated solar radiation as the energy source of high-temperature process heat, the carbothermal reductions of Al2O3 to Al and SiO2 to Si were examined thermodynamically and demonstrated experimentally at vacuum pressures. Reducing the system pressure favors Al(g) and Si(g) formation, enabling their vacuum distillation and avoiding contamination by carbides and/or oxycarbides. Exploratory experimentation in a solar reactor was performed with mixtures of charcoal with alumina and silica in the ranges of 1300-2000 K and 1997–2263 K, respectively, at 10-3 bar by direct exposure to concentrated thermal radiation. Distilled samples contained up to 19 wt% of Al in Al-Al2O3 mixtures and 79 wt% of Si in Si-SiO2 mixtures. When the reducing agent is derived from a biomass source, the solar-driven carbothermal processes are CO2 neutral.IntroductionMetallurgical extractive processes for producing Al1-2 from Al2O3 and Si3-6 from SiO2 are characterized by their high specific energy consumption and concomitant emissions. Alternatively, concentrated solar energy can be used as a high-temperature heat source to drive the carbothermal reductions and, thus, avoid greenhouse gas emissions and other pollutants derived from fossil-fuel-based processes7-12. When the reducing agent is biomass charcoal, the solar-driven carbothermal reduction is CO2 neutral. The carbothermal reductions of Al2O3 and SiO2 are represented by the simplified overall stoichiometric reactions:"

Jan 1, 2011

By E G. Prado

We have confirmed on bench scale the removal of chlorides and alkalies (+95%) and over 2/3 of the zinc, lead and cadmium from EAF dusts. This has been achieved with arrononium acetate solutions alone, or with combinations of water wash, amonia-ammonium carbonate and ammonium acetate solutions. Also confirmed are the process routes for the recovery of the aforementioned elements into marketable products. The technology involves the complete recycling of the reagents. The FAF residue is returned to the electric furnace without risk of impurities buildup. Commercial scale testing with the recycled dust was satisfactory, including quality of the slag and its behavior during the melting stage. A cursory feasibility evaluation is presented.

Jan 1, 1994

By Hiromichi Ohta

Precise thermal properties of molten materials are essentially required for analyzing the metal production process. These properties are also important as a clue to consider the dynamic structure of liquid materials. However, it is difficult to obtain the precise thermal diffusivity values of molten oxides at high temperature because of the experimental uncertainties arising from the bubble formation or the severe separation of radiative and conductive heat components. Recently a novel laser flash method has also developed for measuring thermal diffusivity of molten oxides at high temperature. In this new technique, the sample is melted in a metal crucible and heated to the desired temperature. A single laser pulse is flashed on the bottom of the metal crucible and the infrared ray irradiated from the same bottom surface is measured for obtaining the temperature decay, from which the thermal diffusivity of the liquid sample can be estimated. The usefulness and validity of this new laser flash technique have been confirmed by obtaining the thermal diffusivity values of silicate melts in the wide temperature range between 773 and 1673 K.

Jan 1, 2003

By Frank L. Marley

Mexican silver mining operations have existed prior to the sixteenth century. Recovery processes throughout the centuries were developed at the many mining localities and have progressed through smelting, the patio amalgamation process to cyanidation and flotation. A study of the present silver mining zones is reported in which the ores are evaluated in terms of the mineralogical constituents, their state in the matrix and the effects these are noted to impose upon the efficiency of recovery. Silver mineral identifications were by quantitative ore microscopic and scanning electron microscopic energy dispersive X-ray analysis.

Jan 1, 1982

By S. Neogy, M. Gupta, D. Srivastava, V. Kain, S. Roychowdhury, R. C. Prasad, G. K. Dey

"Austenitic stainless steels are an important material of construction for Boiling Water Reactors (BWR). These stainless steels are amenable to strengthening by strain hardening. Various deformation modes at different test temperatures and strain become active. In the present investigation type 304LN stainless steel was used in the annealed and strain hardened condition. Thin foils were prepared from gauge section for transmission electron microscope (TEM) investigation after tensile testing at room temperature and at 288°C. TEM investigation reveals that twinning is the major mode of deformation for the tests done at room temperature while dislocation cross-slip is the major mode of deformation at higher temperature. Stacking faults were also observed to a limited extent. The extent of twinning was much higher for the tests done using the rolled material. The formation of martensite in the stainless steel due to straining was investigated by the analysis of selected area diffraction patterns.IntroductionAustenitic stainless steels (type 300 series) are an important material of construction in Boiling Water Reactors (BWR). These stainless steels cannot be heat treated but can be strengthened by cold working [1]. Nitrogen alloying of these stainless steels result in high strain hardening rates and higher strength without any loss in toughness [1]. Stress Corrosion Cracking (SCC) in BWR of these types of stainless steels have been attributed to surface strain hardening and strain hardening ofregions adjacent to constrained weldment [2].The test temperature [3, 4], prestrain [5] and nitrogen level [5] has been reported to affect the deformation mechanism during tensile testing. Byun et al. [3] have reported the formation of martensite, dislocations, stacking faults and twinning during tensile deformation, the extent of each depending on the test temperature. Strain localisation has been reported to occur during tensile deformation in irradiated stainless steels [ 6]. The behaviour of rolled material during tensile testing is similar to that of irradiated material to a large extent [3]. Austenitic stainless steels are low stacking fault energy (SFE) materials in which various types of microstructures have been reported to form during tensile deformation and the strain is also highly heterogeneous in nature in these stainless steels which aides SCC in BWR environment to a large extent [7]. During cold working of austenitic stainless steels second order twinning has also been reported [8]. Knowledge about the deformation mechanisms operative in the strain hardened austenitic stainless steels during tensile testing at different temperatures is essential to understand the material deformation behavior and the present study aims at enhancing the existing understanding."

Jan 1, 2011

By Steven R. Izatt

IBC Advanced Technologies, Inc. (IBC) has developed a mercury selective product, which can be used by sulfuric acid producers as either a polisher, or as the primary technology for mercury removal from sulfuric acid. The Molecular Recognition Technology (MRT) separations material selectively binds Hg2+, and to a lesser extent Hg+, out of concentrated sulfuric acid. Mercury output levels of less than 0.1 ppm can be attained by the MRT system. Pilot plant tests have been successfully conducted at base metal smelting operations. A large-scale commercial plant is due for commissioning in 2003. Results from these projects will be discussed.

Jan 1, 2003

By Xirneng Zhu

The electrochemical behavior of Pittsburgh and Illinois coal pyrite in basic and neutral borate/sulfate solutions was investigated. In the transpassive region, aggressive oxidation of pyrite occurred. The reaction products in this region were Fe(III) oxide, sulfate ion and partially oxidized sulfur intermediates. The formation of sulfur and polysulfides was identified by in-situ Raman spectroscopy. The growth kinetics of the reaction product film, resulting from transpassive oxidation of coal pyrites, were studied using chronoamperometry measurement with both stationary and rotating disk electrodes. The reaction rate was well correlated by a paralinear rate equation. The effects of electrode rotation speed, solution pH and temperature were examined. The kinetics were compared to those for mineral pyrite.

Jan 1, 1994

By Chuanhong Li, Zuohua Lin, Zhancheng Guo

"Catalytic mechanism of CeO2 in combustion of coals was investigated in this paper. Catalytic combustion of four kinds of coals with different metamorphic grades by CeO2 was examined, suggesting that catalytic function of CeO2 increases with increase of metamorphic grade of the coals. One important reason for CeO2 promoting combustion of the coals is that pyrolysis of anthracite is advanced by CeO2, which not only raises the pyrolysis rate and pyrolysis conversion ratio, but increases contents of light components in pyrolysis gas; and both pore space and specific surface area of the pyrolysis char are enlarged by CeO2, which is another reason. In order to realize in situ catalysis for reducing catalyst consumption, it is crucial to increase catalyst particle number and enhance the bonding force between catalyst and coal. In addition, remarkable energy saving effect was observed when a nanometer calcium-based rare earth catalyst obtained by hydro-thermal synthesis was applied to catalytic combustion of coal injection into blast furnace.Introduction Coal combustion is acknowledged as one of the most important coal applications. Since addition of catalysts could reduce the ignition temperature of pulverized coal and accelerate the coal combustion, catalytic combustion is generally accepted as an effective measure to realize fast combustion of coal. Furthermore, different catalysts added may produce different effects on ignition temperature of coal. It is reported activity of catalysts with the same cation follows this order: OH->CO3 2->Cl->SO4 2-; while that of the catalysts which have the same anion follows: Cs+>Rb+>K+>Na+>Ba2+>Li+>Sr2+>Ca2+>Mg2+>Be2+ [1-4] .Due to the special physical and chemical structure, CeO2 plays an important role in the catalysis field. Many literatures point out that CeO2 not only has great catalytic effect on energy conversion, succeeded in catalyzing combustion of gaseous fuels such as CH4, CO, etc. but also can catalyze combustion of some liquid and solid fuels such as JP-10, black carbon, carbon deposit in the automobile exhausts and so on [5-9].Pyrolysis, the first step of combustion, directly influences ignition temperature and combustion rate of coals. So a great variety of catalysts were applied to catalyze pyrolysis of coals. And plenty of studies suggest that the alkali and alkaline-earth metal compounds inherent in the coals show apparent catalytic effect on coal pyrolysis. Meanwhile, addition of alkali and alkaline-earth metals into coal combustion process also indicates obvious catalysis effect, accelerating coal pyrolysis, improving pyrolysis conversion ratio, increasing contents of pyrolysis gases and changing composition of the pyrolysis gases [10-15].Although alkali and alkaline-earth metal compounds have good catalysis effect on coal combustion, their application in the catalysis field was limited because of their erosive attack to the combustion equipments. In contrast, CeO2, as a substitution of the traditional coal catalysts, presents widely potential application due to its good catalysis ability, non-corrosive and nontoxic. However, investigation on CeO2 catalyzing coal combustion is rarely reported. In this work, catalytic mechanism of CeO2 in coal combustion was studied, in an attempt to provide theoretical foundation for developing new catalysis technologies."

Jan 1, 2009

By Du Sichen, S. Seetharaman, A. Jakobsson

"In the Present paper, the principles of oxygen potential measurements have been discussed along with the design details for oxygen sensors that are used in copper industry. A description of some of commercial probes is presented along with their salient features. The application of these sensors in flash smelting, converter and casting sections of copper production are discussed along with their implications on process optimization.I. IntroductionThe high temperature galvanic cells have come into prominence on account of their numerous applications in both fundamental as well as applied measurements. Since the inception of the oxygen-ion conducting electrolytes like ZrOrCaO·by Kiukkola and Wagner [1], the oxygen concentration cells have been extensively used in laboratories as well as in industries. In metal-production technology, these cells have been used to monitor the oxygen potentials in metallic, slag as well as gas phases and also to control and styr metallurgical processes. The pioneer among the various industrial users of such cells is the copper industry. To-day, high temperature solid electrolyte cells involving oxygen ion conducting electrolytes have become an integral part of copper pyro-refining and continuous casting. In the present paper some of the applications according to the industrial processes are described including the developments that are going on in the European scene."

Jan 1, 1997

By D. H. Magoon

The zinc smelter of Cominco Ltd. at Trail, B.C. Is the largest In the western world. A total of 550.000 tonnes of concentrate are proceed at the smelter annually. Approximately 80% of the zinc concentrate is roasted and the remainder Is treated by aqueous oxidation preaaure leaching. The zinc concentrate roasting and sulphur dioxide gas processing plants have undergone many changes over the years. This paper describes the processes and equipment currently used for concentrate roasting, S02 gas cooling and cleaning, mercury removal, sulphuric acid production liquid S02 production, and tall gas S02 scrubbing. The recent Installation of an advanced process control system for the operation of these Integrated processes Is also described.

Jan 1, 1990

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. This project is concerned with the determination of the effects of operating variables on the reaction of the particles. Experiments were carried out in a large laboratory-scale flash furnace with 72 wt-% Cu matte by varying initial particle size, temperature, oxygen partial pressure, oxygen-to-matte mass ratio and residence time. Chemical analysis was used to study the oxidation extent and copper volatilization. Particle fragmentation was examined. Fractional conversion and sulfur removal slightly decreased with initial particle size, while a higher oxygen-to-matte mass ratio mainly resulted in higher fractional conversion and more efficient sulfur removal. The fractional conversion values represented the overall extent of oxidation more closely than degree of sulfur removal.

Jan 1, 1997

By Marietta Canty

A paper is presented in which an innovative biological process is described for the treatment of cyanide-, metals-, and nitrate-contaminated mine process water. The technology was tested for its ability to detoxify cyanide and nitrate and immobilize metals in wastewater from agitation cyanide leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to demonstrate the technology on a mine process waste stream at a mine in Nevada. The demonstration was performed Jointly under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered by the U.S. Department of Energy's (DOE) Western Environmental Technology Office (WETO) and the Superfund Innovative Technology Evaluation (SITE) Demonstration Program under Interagency Agreement Number DW89938513-0 I-0. MSE Technology Applications, Inc. (MSE) located in Butte. Montana, was the contractor responsible for conducting the project, and Pintail Systems, Inc., of Aurora. Colorado, was the technology provider. The pilot-scale unit was field-tested at the Echo Bay McCoy/Cove Mine southwest of Battle Mountain, Nevada. The biotreatment process was considered to be successful in destroying cyanide in the mine process water. The process was also determined to be effective in removing metals. The pH was consistently neutralized, and nitrates were successfully removed from the mine process water. As a result of conducting these pilot-scale tests, the biotreatment process was concluded to be an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1998

By L. Becze, S. J. Hock, G. P. Demopoulos

"Regeneration of HCl from chloride solutions is commercially practiced by high temperature (800-900 °C) pyrohydrolysis associated with high energy consumption and capital cost. As an alternative to pyrohydrolysis a novel low temperature ( <200 °C) non-autoclave hydrolytic process has been studied in this research work, which comprises two steps. In the first step, ferrous chloride is oxidized by oxygen at 1;150 °C, followed by hydrolytic decomposition of ferric chloride to coarse hematite particles and superazeotropic hydrochloric acid (8-9M) operated at approximately 180 °C. This paper provides a summary of the laboratory results related to both oxidation and hydrolysis and presents a newly designed conceptual process flowsheet.IntroductionRecovery of base, noble and rare metals from ores and secondary materials (slags, dusts, residues) by chloride-based hydrometallurgical processes holds a lot of promise if a low cost HCl process becomes available. This is particularly so due to the high activity of HCl or more accurately activity of hydrogen ion [1] in concentrated chloride media and the formation of chlorocomplexes allowing for effective leaching under atmospheric leaching conditions and simultaneous ease of metal separation. However, during leaching significant amount of iron, which is associated with most of ores and secondary materials, goes into the solution. Hence, the obtained leach solution has to be treated to convert iron chlorides into easily filterable iron oxide and simultaneously produce concentrated hydrochloric acid. Apparently the critical operation of these processes is the regeneration of the lixiviant (HCl). Currently in the industry, its regeneration is accomplished by high capital and intensive pyrohydrolysis which operates at 700- 900 °C. Aimed at lowering the operational cost of pyrohydrolysis a process called PORI [2] was developed and tested in pilot plant scale in the 1970s for the purpose of treatment of pickle liquors without, however, resulting in industrial application."

Jan 1, 2011

By Wantae Kim, Jaechun Lee, Tatsuya Oki, Sungbaek Cho, Sangbae Kim

"Effect of attrition scrubbing on the recovery of platinum group metals(PGMs) from automotive catalytic converter was discussed. The attrition scrubbing as comminution and separation process was effective for the recovery of the catalyst layer, ?-alumina, from ceramic supporting matrix, cordierite, by physical impact and shearing action between particles in the scrubbing vessel. The catalyst layer was dislodged from the surface of the supporting matrix into fine particles less than 45µm by attrition scrubbing. The production of fine fraction less than 45µm increased as the residence time for attrition scrubbing increased. The fine fraction obtained at the residence time of 40min contained 19.25% CeO2, 1.93% ZrO2 and 418.8ppp PGMs. The recovery of ?-alumina in the fine fraction increased as the residence time increased. Simultaneously, the recoveries of CeO2, ZrO2 and PGMs increased and reached up to 82.9% CeO2, 78.7% ZrO2 and 78.9% PGMs at the attrition scrubbing time of 40min. The production of the fine fraction and recovery of ?- alumina increased when the solid concentration and initial feed size increased.IntroductionThe automobile catalytic converters contain appreciable amount of PGMs. Currently several million tons of used catalytic converters are disposed annually worldwide, each containing about 0.5-1g of platinum and 1-2g of all PGMs1). The recovery technologies of PGMs from spent catalytic converters have been thoroughly reviewed by numerous researchers since last decades. Two types of methods, wet and dry processes, have been commercially operated. In the wet process, the PGMs on the spent catalytic converters were dissolved mostly in the form of chlorocomplex, MCl6 2-, by contacting with aqueous solutions. Subsequently the resulting solutions are treated to concentrate and the precious metal ions are reduced by introducing metals such as Al, Fe and Zn in the concentrated system2). In the dry process, the spent catalytic converters are melted, in some case with CaO, at an elevated temperature to produce a low viscous slag. The PGMs in the melt are separated by allowing them to adsorb on Fe or Cu having high specific gravity7). Although highly pure precious metals could be obtainable, the recovery technologies of PGMs currently operated seem not to be cost-effective since PGMs embedded in these types of catalytic converters are present in very small quantities."

Jan 1, 2008

By John R. Howell

"SUMMARYThe process of producing a new cast component requires significant design and development by both the design engineer and the foundry engineer. This effort strives to produce a high quality component at minimum cost. To assist in this development, an analysis system, consisting of several computer programs, has been developed to simulate the metal casting process. This system incorporates analytical geometric solid modeling, finite element analysis, results display, and an innovative technique to model the casting mold with surface boundary conditions.The simulation has produced excellent thermal results and work is in progress to develop techniques to enable use of this data in additional analyses to predict porosity and residual stress. Research is required to produce working parametric formulations of material properties. Software development is required to develop good fluid flow analyses for large. 3D models to simulate filling of and convection in molds.Integrating this system of programs is difficult due to proprietary database structures used by software developers. However, an acceptable means has been accomplished' to move data from one program to another. Further software development is required to facilitate this task. INTRODUCTIONThe process of producing a new cast component requires significant design and development by both the design and foundry engineer. This effort strives to produce a high quality, reliable component at minimum cost in a timely manner. The design engineer needs to know the physical and mechanical properites which can be expected in the actual part at critical areas. This will enable him to design a part with minimum material while fulfilling the performance required. The foundry engineer needs to produce a sound, quality casting with a minimal amount of material In risers, the feeding system and machining stock. This must be done with a minimum· investment in tooling and development time and maximum productivity of labor and capital employed. This task Is continually being made more difficult because of increased competition in the marketplace and the use of castings in more severe service. This has strongly influenced the need for high quality castings.The task of developing a new casting is difficult for both the design and foundry engineer. To assist in this development, Deere & Company has been engaged in the development of an analysis system to simulate material processes. A major portion of this program involves simulation of the metal casting process. This analysis system has evolved into a package of computer programs which simulates casting solidification and subsequent cooling through the finite element method"

Jan 1, 1986