Search Documents

By W. S. Fyfe, R. J. Puddephatt, S. Zhou

Gold is easily mobilized at temperatures within range 600-11OO°C by gases such as Cl2, CO, H2S, in gas mixtures, at low pressures. Such gases are relevant to conditions of granulite facies metaomorphism in environments of magma underplating. These observations suggest an efficient mechanism for moving gold to the upper crust during major thermal events. The efficiency of precipitation of gold at lower temperatures is related to available mineral surfaces and pyrite appears to be an excellent substrate for gold precipitation.

Jan 1, 1989

By K. F. Unrug

The identification of the major subsidence areas in the Western Kentucky Coal Field has been made to distinguish the subsidence phenomena on the basis of geographical location Further, this identification process is based upon selected critical geological, topographical, and mining features in the coal fields. The proposed identification of the regions is derived from a comparison of the subsidence potential in a particular area. The most likely severe subsidence areas are compared to those with the probable low subsidence severity. The combination of certain geological and mining parameters involved allows for the derivation of a classification of the subsidence potential. It is recommended that further site specific studies should be performed on this area.

Jan 1, 1986

By M. E. Lewellyn

A lower moisture content for a clean coal product means increased Btu content, or increased yields at the same Btu content, and lower operating costs. The conventional surfactant-based dewatering aids effeciently lower the moisture content but often the presence of residual surfactant in the filtrate and recycle water causes problems downstream. ACCOAL-DRI 1000, a surfactant-based dewatering aid, was developed to solve this problem by minimizing the downstream effects while efficiently lowering the moisture content. The theory of the use of surfactants in filtration will be discussed as well as the development and field evaluation of this new product.

Jan 1, 1988

By Wendell H. Wiser

A comparison is presented of coal pyrolysis at temp¬eratures ranging from 4090 to 497°C and thermal dissolution of coal in tetralin at temperatures ranging from 350° to 450,°C, both utilizing a Utah high-volatile bituminous coal. The initial coal pyrolysis reactions are second order with an enthalpy of activation of 35.6 kcal per mole. The fraction of total product yield produced under second order conditions ranges from 67% at 409°C to 96% at 497°C. The process then gradually deteriorates to a first order reaction in the later stages with enthalpy of activation of 4.1 kcal, per mole. The initial reactions of solution of coal in tetralin are second order with an enthalpy of activation of 28.8 kcal per mole. The fraction of total product produced under second order conditions ranges from 63% at 350°C' to 94% at 450°C. The dissolution process then gradually changes to first order in the later stages with enthalpy of activation of 15.6 kcal per mole. A model is presented which relates the two processes and explains, the significance of the above similarities.

Jan 1, 1967

By Lyle A. Hale

The subject area known as upper Dry Valley is located 15 miles due east of Soda Springs in Sections 14 and 23, Township 9 South, Range 44 East, Caribou County, Idaho. The railroad extending from Soda Springs to its terminus at El Paso's Maybe Canyon mine is 8z miles to the north in lower Dry Valley. Initial data derived from trench work in 1962 revealed a variety of econom¬ically significant alterations of the phosphatic beds related to the rather unique geomorphic development in the northern part of phosphate lease 1-012989. It was apparent that such conditions, while valid for near-surface beds in a strike direction, would be misleading if projected to the proposed depth limits of strip mining. Consequently, a subsurface mapping program was initiated in 1963 to determine: (1) the depth and horizontal extent of weathering and related phe¬nomena, (2) the depth, thickness, and quality of ore beds and intervening strata, and (3) structural geology as a guide for mining procedures. Successful use of a scintillometer in 1956 to detect the subcrop position of phosphate beds in the Smokey Canyon area of southeastern Idaho led to the conclusion that gamma radiation surveys of drill holes could be a useful aid in subsurface mapping. The objectives of this paper are: (1) briefly to describe geologic features characteristic of the phosphate lease area and (2) to demonstrate the practical application and theory behind gamma radiation logging as an effective tool in the economic evaluation of a phosphate lease.

Jan 1, 1969

By J. Gallegos, R. Faber, T. Cox

"An innovative method to reduce acid rock drainage (ARD) and sediment loading of a recreational lake was used in the Red River watershed in northern New Mexico. The Red River drains a mining district that contains multiple naturally occurring hydrothermal alteration zones that release ARD and sediment to the river during episodic summer rain storms. A lake is near the mouth of the watershed and is filled with water from the river through a sluice gate and diversion. An automated actuator was installed on the sluice gate to close when the river is impacted by high-suspended sediment. Water quality probes were installed at the sluice gate to monitor the river water for turbidity, specific conductivity and water depth. If high turbidity is measured, the sluice gate closes automatically. Remote access is setup with a computer view screen to review the real-time system status. Once the turbidity drops below a threshold, the sluice gate is reopened remotely. The automated sluice gate has successfully reduced the amount of ARD and suspended sediment entering the lake. This reduction has resulted in an improved aquatic habitat for the fishery and benthic macroinvertebrate community. BACKGROUND The Red River is located within the Sangre De Cristo Mountain Range in northern New Mexico. The river drains an area of approximately 190 square miles and spans elevations from 6,600 feet at its confluence with the Rio Grande to its headwaters near 12,000 feet (Figure 1). The river generally flows to the west along most if its length.The Red River watershed includes several hydrothermal alteration zones. The alteration zones were created by intrusion of high-silica granites and subvolcanic porphyries, with associated hydrothermal fluids, into the volcanic rocks of the Questa Caldera. The hydrothermal alteration is also responsible for the molybdenum deposits in the area. Rapid chemical weathering and physical erosion of pyrite-rich hydrothermally altered rocks has resulted in the formation of alteration scars. The alteration scars are characterized by steep, erodible slopes with little vegetation and incised gullies. Debris fans from the drainages containing active alteration scars have formed and typically consist of poorly sorted sand and gravel that is distinctly pale yellow in color. Some of the more prominent scars are located in the Hansen, Straight and Hottentot Creek drainages downstream of the town of Red River."

Jan 1, 2018

By S. G. Malghan, W. H. Moyer

In reference to the section "Excess pyrite," the author discusses difficulties in separating chalcopyrite from pyrite. A technique does exist, and has been used commercially, for the flotation, separation, and recovery, if desired, of both chalcopyrite and pyrite. The method was described in Mining Engineering, March 1966, "An Improved Flotation Method for Cornwall Sulfides." While it was not used on a porphyry copper ore, it was used on a chalcopyrite- pyrite-containing ore and might well have application. Both sulfides, chalcopyrite and pyrite, were floated simultaneously using xanthate as a collector and MIBC frother to produce a cleaned sulfide product. This concentrate was then thickened and conditioned at high solids with aeration and lime to a pH above 12.0 for a period of 1.5 to 2 hr. A supplemental suppressant, such as cyanide, could be used if necessary to sharpen the subsequent separation; however, it was not required at Cornwall. The conditioned sulfides were floated with two stages of cleaning to produce a high- grade chalcopyrite froth product and a pyrite sink product barren in copper. The separation at Cornwall gave a 28.6% Cu grade chalcopyrite product and a pyrite analyzing 0.06% Cu. A desliming step on the raw ore initially used at Cornwall for a period of time was later discontinued. Advantages to be found in using a strong sulfide collector, such as a xanthate, is the rapid flotation it induces and, generally, an ability to float at a coarser grind. A following regrind circuit could be used to give maximum liberation and produce a clean sulfide concentration. The "differential" separation is concerned primarily with grade and with assuring a barren pyrite for maximum recovery.

Jan 1, 1987

By Jon “Ike” Isaacson, Frank Perrone, Eric Prantil

"Tunneling through an urban environment carries many inherent risks to the immediate local infrastructure and subsequently to the project stakeholders. On the CQ031 Contract of the East Side Access Project in Queens, New York, twin 22.5’ diameter Herrenknecht Slurry TBMs were mined within close proximity to many infrastructure assets, with cover of less than half a shield diameter at times. Multiple public bridges and critical railroad infrastructure including catenary poles and signal towers supporting the busiest rail interlocking in the United States required underpinning systems. The support program for these structures was refined over the course of the four tunnel drives. It is the intent of this paper to show how the interaction between the temporary structures, instrumentation monitoring plan, and risk assessment program melded to provide a system which the owner, contractor, and designer relied on as a tool to ensure the project success without impacting the public surroundings. PROJECT BACKGROUND The East Side Access (ESA) megaproject located in New York City, N.Y is a multi billion dollar program for the Metropolitan Transit Authority Capital Construction (MTACC) with the main goal of bringing the Long Island Railroad (LIRR) commuter rail to Grand Central Station located in the heart of Midtown Manhattan. When completed, the project will significantly reduce congestion both into and out of Penn Station, the current terminus of the LIRR. In order to accomplish this, multiple contracts of varying scope are required to operate simultaneously in both Queens, N.Y and Manhattan. In 2009, the CQ031 Queens Bored Tunnels Contract was awarded to the joint venture of Granite Construction Northeast, Traylor Bros. Inc., and Frontier Kemper (G.T.F). The main scope of this contract was to excavate four segmentally lined soft ground tunnels underneath the Sunnyside Rail Yard in Queens, New York. Additional scope of work included the construction of a tunnel approach structure, electrical substation, and multipurpose ventilation and egress facility."

Jan 1, 2016

By Alper Kirmaci, Taghi Sherizadeh, Gunnar Wurst, Paul Brooks, Dogukan Guner, Samuel Nowak, Mina Esmaeelpour, Kutay Karadeniz

As mines continue to deepen and become more expansive, active monitoring of larger volumes of rock mass will become more critical to calibrate numerical simulations and to ensure the safety of underground workers. Monitoring larger volumes of rock mass requires low-cost sensors that are simple in construction and installation. In this study, a novel hybrid optical fiber cable (HOFC) designed for use in distributed optical fiber sensing (DOFS) via grouted boreholes was deployed to monitor a bulk mining operation in an underground metal mine. The HOFC was successfully used to monitor approximately 2.7 × 10 m3 of rock mass above excavations surrounding a pillar removal area in which six large pillars were removed simultaneously. A total of six measurement boreholes (maximum depth of 22 m) were used to measure strain along the optical fiber during the pillar removal operation using the HOFC, allowing for 70 individual strain measurement points, which were constructed for under one U.S. dollar each. Monitoring of the excavation area took place over a 44-day period after pillar removal. Extensional strains were noted in the areas closest to the removed pillars, while areas of compression were noted directly above the remaining pillar in the area. The results of the case study demonstrate that a low-cost optical fiber strain sensing network can be rapidly installed in a large excavation area and can provide highly sensitive strain measurements in a manner that would be cost prohibitive using other methods.

Oct 1, 2024

By J. Sharp, R. Arnold, P. Rusin, T. Young, N. A. Sinclair

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environmentally unacceptable. Bioreductive leaching of such ore samples at MBX resulted in high extractions of silver and molybdenum. When baseline, three-day, cyanide bottle-roll tests were conducted on manganiferous-oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bioreduction with 99.8% dissolution of manganese. A followup cyanide bottle-roll test yielded an additional 8.5 % silver dissolution, for a total extraction of 94.5%. Baseline, three-day, acid bottle-roll tests of the iron-oxide molybdenum ore Yielded 1.8% molybdenum. However, bioreduction solubilized 93.3% of the molybdenum into the growth medium. An additional 0.3% molybdenum was solubilized during the followup acid bottle-roll test. Microbial treatment of refractory oxide ores with bioreductive bacteria resulted in higher extractions of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and molybdenum was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1993

By V. Svalbonas

In the establishment of a useful failure criteria for complicated, fabricated structures, two basic areas of knowledge must be evaluated: 1. The accuracy of the applied stress analysis must be known in comparison with actual stresses encountered during mill operation. 2. The metallurgical fracture properties of the basic materials must be established with reference to non-destructive examination (NDE) methods to be used during fabrication. Both of the above can only be evaluated by use of full scale tests on the structures, and/or components, of interest. This paper describes such tests and comparisons as applied to several large mill installations. In addition, weldment component fatigue tests arid flawed casting strain gauge tests are also discussed. The combination of such test results allows for the formulation of failure criteria directly applicable to the fabrication and examination procedures followed in grinding mill structure manufacture.

Jan 1, 1982

By C. R. Daly, D. Biswas

This study presents the development of a simplified artificial neural network (ANN) for the characterization of rock mass with a simultaneous display of its output in a three-dimensional interactive environment as well as in the form of a text document. The system was developed using JAVA object-oriented language, virtual-reality modeling language (VRML) and JavaScript, and it runs on the Internet. The user can walk through a three-dimensional virtual roadway, checking the underground rock mass behavior and, consequently, can design a support system. The system first characterizes the rock mass with the help of a neural network and recommends a suitable support system for the particular geomining condition. The system then represents its output in a three-dimensional environment. The neural network developed in this system was trained with 261 data sets, and its performance was evaluated with five case histories. The evaluation results showed that the network could identify the rock category and support system adaptively. The average error for the support load was 2.7%. Among the five case histories, two were represented in a three-dimensional environment. The output obtained from the overall system compared favorably with the existing underground conditions.

Jan 1, 2003

By A. Bruynesteyn

Procedures are discussed to determine if a waste material can become acid producing when left exposed to the environment. When wastes proves to be acid producing, methods are described that can be used to determine the characteristics of the effluents produced from a commercial size waste dump, taking into consideration that large quantities of pollutants can accumulate inside a waste dump during dry periods. The length of such dry periods and the quantity of rainfall greatly affect effluent characteristics.

Jan 1, 1980

By Donna L. Boreck

In an effort to increase recovery in thick and closely spaced coal seams, the Bureau of Hines, U.S. Department of the Interior, is studying the feasibility of introducing three mining methods-high-face longwall, multi-slice longwall, and longwall caving-in western coal operations. Geology plays a significant role in determining the success of such methods. Some of the factors that will affect development are as follows: (1) thickness and three-dimensional configuration of the seam, (2) cleats, joints, and fractures in the coal and roof rock, (3) roof composition and variability, and (4) coal quality and changes in quality within the seam. Through geologic mapping, the presence of many of these factors is predictable prior to development.

Jan 1, 1987

By Harold Bloom

The Mount Pleasant Mines, or Mount Pleasant Joint Venture as it is presently known, is located approximately 59.5 km (37 miles) south of Fredericton, NB, Canada. Earliest indications of mineralization were found in 1954, during a regional reconnaissance geochemical stream sediment survey carried out over large parts of New Brunswick and the Gaspé Peninsula. The regional geology of New Brunswick is shown in Fig. 1. This program, sponsored by Selco Exploration Co. Ltd. of Toronto was conducted by H. Bloom, H.E. Hawkes, J.E. Riddell, and J.S. Webb. At its conclusion in 1955, 30 significant anomalous drainages were identified for follow-up evaluation. A total of 4937 sample sites were occupied. Geochemical reconnaissance using stream sediment sampling was a new technique which had only been field tested the previous year in the Gaspé and the northern coastal area of New Brunswick. Sediments collected from known mineralized drainages were found to leave a train of anomalous heavy metals from 1.6 to 9.7 km (1 to 6 miles) in length. When the exercise was extended to a reconnaissance survey, the previously unknown mineralized prospect at Nash Creek, New Brunswick, was discovered, staked, and later drilled (Hawkes and Bloom, 1956). Although it did not come into production, the discovery left little doubt as to the viability of the method and led to the Selco sponsorship of the program for the following two years.

Jan 1, 1991

By RICKARD HANSEN

Vehicle fires in underground mines pose a certain risk for which measures to prevent or mitigate the fires are highly important. Fire protection measures can be divided into active and passive measures, where active measures require an external power to work in the event of a fire, and passive measures could include an existing partition preventing fire spread. As passive fire protection does not rely on activation, it is expected to provide high reliability and a robust solution, and should be considered during the design process. This paper investigates passive fire protection measures that could be implemented in the design of mining vehicles. It was found that passive fire protection should include the use of several measures simultaneously to ensure fire protection throughout the different phases of a fire. Threshold distances for fuel components were calculated, and it was found that combining hydraulic hoses and electrical cables resulted in larger threshold distances. A pool fire along the underside of a vehicle will pose a certain risk, and passive measures should be focused on ignition prevention, making high demands on the insulation/shielding along the underside. Any occurring tire fire may pose a challenge, and the priority should be on preventing ignition. Potential measures include shielding the wheelhouse and applying fire-resistant sealings.

By K. E. Robinson, G. Re, L. Skoski

Introduction A new technology is evolving as a result of growing industry and government concerns over the potential impacts of possible airborne emissions from uranium tailings piles. A major component of the technology is the use of earth covers to stabilize the tailings after mill operations have ceased. While various analytical models have been used to predict the thickness of required covers, experimental validation of the models has been necessary. This paper presents the results of a field program to select and test cover material to determine its suitability for eventual reclamation of a currently active tailings pile. The two main criteria guiding the study were the U.S. Nuclear Regulatory Commission radon flux requirements (reduction to less than twice background pre-1979, and to 2 pCi/m2 -sec above background post-1979) and the desire to employ locally available material. The methodology chosen for this study consisted of three main elements: o Determination of the background radon flux. o Determination of the radon flux from the tailings pile. o Experimental determination of the cover material diffusion coefficient and and calculation of cover thickness. The first two elements of the study are relatively straightforward, the last phase is discussed in detail. Background Radon Flux Measurements of radon-222 emanation rates from the surface of the ground were taken at three sampling locations. Samples were collected by means of the accumulator can method described by Wilkening, 1977. Both morning and afternoon samples were collected at each site to obtain an average. The measured fluxes were fairly uniform and did not differ greatly among sites. The overall average flux for all sites was 0.63[+]0.28(o) pCi/m2 -sec. This value is equal to the average radium-226 concentration determined in the soil, thus yielding a one to one ratio of radon-222 emitted (in pCi/m2 -sec) to soil radium content (in pCi/g). Tailings Pile Radon Flux Two sites on the tailing pile

Jan 1, 1980

By Hans-Henrik Wallin

The stresses in the heads and shell of a grinding mill are largely dependent on the bending moment produced by the trunnion bearing. By using spherical roller bearings in a special narrow housing a short moment arm is obtained and the bending moment is reduced. For large mills a hydrostatic shoe bearing which also gives a short arm, can be used. Spherical roller bearings also require less maintenance and have a long service life. As the bearings are grease lubricated an automatic lubricator is used instead of an oil lube system. Service data from two Swedish mining companys confirm the fact that the above arrangements provide a long service life.

Jan 1, 1979

By J. M. Avasthi

Gulf Research & Development Company conducted the nation's first underground coal gasification test in steeply dipping beds near Rawlins, Wyoming. The geotechnical considerations played a major role in the initial site selection. The test plan included a detailed geotechnical program for site evaluation, test design, permitting, and environmental studies before the burn. During burn, the geotechnical activity continued in the form of monitoring surface subsidence and acoustic emission. The postburn evaluation included studies of the drill cores obtained from the burn zone and effects on the surrounding rock mass.

Jan 1, 1981

By J. H. Rowland

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on the effectiveness to extinguish conveyor belt fires. The four different types of suppression systems were water sprinkler, deluge type water spray, and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 72-in-wide fire resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 500-550 feet per minute (fpm) and 1350-1500 fpm. Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to extinguish any smoldering belting was greater than the current MSHA regulations require. MSHA regulations only require 10 minutes of water supply to the suppression system. In the test set up neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 500 fpm air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test set-up, arrangement of the fire suppression systems, and conclusions regarding the effect of air velocity on fire suppression system design and performance. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009