Search Documents

By William E. Foreman

Editor's Note: For purposes of uniformity throughout this book, Coal Preparation, 5th Edition, the editors have advocated the use of the U.S.A. Sieve Series of testing sieves (see Table 6-2) as the testing sieves of modem choice. The adoption and use of the U.S.A. Sieve Series and its forerunner, the Tyler Standard Screen Scale, has for over seventy-five years introduced uniformity into reports; has simplified the comparison of results; and has provided control for operation of modem coal preparation circuits. While a full explanation of the differences, and more importantly the similarities of these two measuring systems cannot be stated here, it is felt that a brief clarification of terms is in order. The difference between the U.S.A. Sieve Series and the Tyler Standard Screen Scale Sieve Series is the identification method. Tyler Screen Scale sieves are identified by mesh designation with the width of opening varying by the square root of two, or 1.414 times the width of opening in the previous sieve. The U.S.A. Sieves are identified by openings in millimeters or microns and also arbitrary numbers which do not necessarily mean the mesh count; this series uses width of opening variations in the order of approximately the ratio of the fourth root of two, or 1.189. Tyler Standard Screen Scale and U.S.A. Sieves can be used interchangeably, and to avoid confusion the nameplate of all Tyler Screen Scale sieves show the U.S.A. Number, while all U.S.A. Sieves show Tyler Screen Scale mesh equivalent numbers on the nameplate. INTRODUCTION Sizing is the process of separating mixed mineral particles into groups of particles all of the same size, or into groups in which all particles range between definite maximum and minimum sizes. This chapter applies the modem mechanical screen and the liquid-solid cyclone (hydrocyclone) to the process of sizing solid particles as applied to coal preparation. Screening is a mechanical process that separates particles by size. Modem coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modem preparation plants is done for the following reasons: 1. Removal of fine coal before a size reduction step. 2. Size separation of the coal into a coarse and fine fraction for sized products or for processing in coarse and fine coal circuits. 3. Recovery of heavy media from heavy media coal cleaning circuits.

Jan 1, 1991

By John E. Miller

In recent years there has been increasing concern in the mining industry over the availability and high cost of diesel fuel to support mining operations. Unit Rig & Equipment Co. has been deeply involved with the development and testing of the newest designs for trolley assist. Beginning in dune 1980, Unit Rig modified and commissioned six 156 metric ton (170 short ton) trolley assist haulage trucks at two mine locations in South Africa. Operating haulage trucks with General Electric GTA 15E/776 drive systems were chosen for the tests since this size of truck represented the majority of the population of large size haulage trucks and the greatest technical development problems. Test operations have proven the feasibility of equipment designs in actual operation and preliminary economic data has convinced the operators to proceed with planning to modify their entire mining operation to use trolley assist. The initial capital investment incurred for trolley assist can be recovered in a short period of time. Following this quick capital recovery, mines will continue to realize lower operating costs through increased productivity and lower diesel consumption.

Jan 1, 1980

By Biswajit Samanta, Pranjal Pathak

A multimine mineral value chain (MVC) consists of multiple mines in the upstream supplying raw materials to multiple destinations in the downstream. The short-term mine production scheduling problem of a multimine MVC aims to determine the optimal extraction sequence and destination allocation of blocks from all the mines collaboratively to meet the quality and quantity requirements of all the processing plants in each period, subject to all relevant technical and operational constraints of the mining system. It is carried out at shorter scales of days/weeks/months under the purview of long-term production scheduling. An optimal short-term production schedule for MVC involving multiple mines that share the same infrastructure (processing units, stockpiles and waste dumps) requires coordination across the network of mines. Optimizing the short-term production schedules independently at each mine fails to capture the benefit of collaboratively generating schedules for all the mines, resulting in suboptimal schedules. Additionally, in short-term production scheduling, the operations are modeled in greater detail with additional decision variables and constraints to model the more complex multimine MVC situations. This makes the large-scale instances of the problem computationally intractable for standard mixed-integer programming (MIP) solvers. This work presents a customized genetic algorithm (GA)-based heuristic approach to obtain near-optimal solutions to the industrial-scale instances of the short-term production scheduling problem of multimine MVC within a reasonable computation time.

Oct 1, 2022

By Steven W. Hunt, Gregory C. Baker, Glen J. Rorison

Microtunneling methods were utilized beneath pile-supported clarifier basins to replace settlement damaged sludge drain lines at the Jones Island Wastewater Treatment Plant in Milwaukee, Wisconsin. To minimize the risk of blockage and expensive recovery of a microtunnel boring machine against pipe piles or construction debris, a Soltau RVS 80 was utilized. This machine allowed the alignment to be initially bored with guided 114-mm diameter rods to ensure proper alignment and lack of obstructions. Casing pipe was then installed by jacking 1-m long, 305-mm diameterclay pipe along the rods and behind an auger head. This case history also discusses how 2.4-m diameter precast concrete pipe was used as a one-pass sinking caisson for workshafts and new cleanout manholes.

Jan 1, 2001

By Joseph T. Matoney, Okley B. Bucklen, Claude A. Goode, Philip G. Meikle

INRTODUCTION Annual coal production rose to over 1.03 billion st (931 Mt) in 1990. At the same time the number of mines producing this increased tonnage has decreased over 60% in a 30-year period, from 9230 mines in 1960.1 The great increase in production made possible through continued mechanization requires greatly improved loading facilities just to get coal away from the mine. Also the trend to combine production from more than one mine and cleaning it in a single preparation plant continues. A recent census of US coal preparation plants indicated that 310 plants were in operation.2 In addition to increased loading capacity, storage and blending facilities are more necessary both at the producer and user end. In this climate of rapidly changing technology, any written account is faced with the possibility of obsolescence before its appearance. Thus, this chapter seeks to define the common and current practice in coal loading and storage facilities with the full knowledge that this practice is an ever-moving target. FUNDAMENTALS OF COAL STORAGE Storage of coal is becoming an increasingly important part of coal handling systems at mines, particularly since the advent of the unit-train concept in transportation. In order to take advantage of reduced transportation rates on trainload shipments of coal offered by unit-train movement, operators have found that storage is an economic necessity. In unit-train practice, large predetermined quantities must be loaded in relatively short periods of time, as opposed to conventional practice where coal is loaded at a speed dependent on the production capacity of the mine and/or the cleaning capacity of the preparation plant. Clean coal storage is generally practiced in order to accomplish one, or a combination, of the following objectives: 1. To load out promptly and economically. 2. To facilitate blending in order to even out chemical and physical inconsistencies and to prepare desired products or to attain maximum product uniformity. 3. To store certain sizes whose prices and market demand fluctuate with seasons and to permit shipping in good weather. Coal storage, then, is necessary and desirable, both from production and utilization standpoints. There are, however, several undesirable aspects attendant to the storage of coal, the most important of which are oxidation and spontaneous combustion, changes in properties which may affect utilization of the coal, degradation of coal due to rehandling, and the added cost of handling and storage facilities.

Jan 1, 1991

By William S. Pintz, William A. Vogely, Charles J. Johnson

This chapter on the role of minerals in developing economies is oriented toward economic policy issues. The discussion and analysis cut across the technical, economic, legal, and policy fields. The goal of this chapter is to pro- vide relevant background information important to individuals involved with the minerals sector in developing countries. Where possible, trends are shown to provide a basis for understanding the evolving role of minerals in developing economies. This chapter is divided into the following five sections: (1) characteristics of developing countries (which presents selected statistical comparisons); (2) government objectives in developing countries; (3) government policy formulation in developing countries; (4) determinants of future trends, and (5) a summary of the chapter's major points combined with the authors' view. CHARACTERISTICS OF DEVELOPING COUNTRIES There are 155 nations in the world categorized as "developing countries." In total these nations represent about one third of the value of the world's mineral production, three quarters of the world's population, and over half of the world's land surface area. The group of so-called developing countries is quite diverse and there are exceptions to almost any general observation about the group as a whole. Most definitions of the term "developing country" are based on levels of per capita income. However, if per capita income is the sole criterion used in categorization, then several oil-exporting countries would jump from the category of developing country to the category of developed country.a Obviously, this results in a poor fit with respect to other measures. In general, the majority of developing countries can be characterized by relatively low per capita income, high population growth rates, high levels of unemployment, low levels of education, short average life ex- pectancies, income distribution skewed toward the highest 20% of the population, and a large share of exports represented by primary commodities. b For the purposes of this chapter a slightly modified version of the widely used World Bank system of classification (shown in Table 1.2.1) is used. As summarized in Table 1.2.1, developing countries are divided into three main groups based on estimated gross national product (GNP) per capita. It should be noted that the high- income, oil-exporting countries have characteristics of both developing and industrialized countries; however they are included for most statistical comparisons within the group of developing countries. Of the 155 developing countries in the world, approximately half produce minerals other than common building materials, and only 32 account for more than five percent of world pro-

Jan 1, 1985

An insufficient hydrologic data base exists for most large and small coal basins in Alaska owing to the lack of need in the past to collect data. The runoff process is insufficiently understood which is complicated by specifically northern phenomenon, and the lack of understanding of hydrologic relationships in permafrost environment. This paper presents an understanding of the hydrologic effects of frozen ground and presents methods by which the influence of surface mining upon the hydrologic balance can be analyzed.

Jan 1, 1988

By J. A. Procarione

Introduction Ventilation engineers have always felt somewhat uneasy when, in the normal course of their work, they are forced to consider the flow in any mine entry as "wholly rough." Under such conditions in pipes, friction factor is no longer a function of Reynolds' number. This assumption serves to simplify the problem and overcome an evident lack of information concerning the variability of K-factors. During the summer of 1985, a unique opportunity to investigate the reaction of friction factor to changing flow rates presented itself. A Utah coal mine was temporarily directing a substantial airflow through a single entry. By regulating the quantity, it would be possible to obtain a wide range of Reynolds' numbers in an entry composed of two distinct coal thicknesses. This paper describes the conducted study. The theory covering basic fluid flows in pipes that led to the questioning of constant K-factor is presented first. Experimental procedures are then described, including the use of a view camera in determining entry area and perimeter. Finally, a discussion of the observed variations in friction factor versus Reynolds' number is given. Changes of 34% and 45% in K-factor were seen in this study for the two entry heights. The implications of ignoring the relationship in this case and a call for an expanded research effort are also presented. Theory Since a gas is a fluid, the general principles of fluid mechanics are equally applicable to airflow in a mine entry as they are to the flow of water in a pipe. The Darcy equation is, therefore, equally applicable to pressure drop calculations in both situations. This famous formula was originally derived for use in circular cross sections and may be modified for any other shape by the use of hydraulic radius (defined as the area divided by the "wetted" perimeter). The Darcy equation relates the physical parameters of the pipe (diameter, length, and resistance to flow) and fluid velocity to the energy needed to create the flow. A study by Nikuradse (1933) brought to light the suspected dependency of the friction factor term in the Darcy equation upon Reynolds' number. By performing a large number of laboratory experiments, he established some basic concepts upon which other researchers built. Chief among these contributors was Colebrook (1939). Using commercial-grade pipe, he established an empirical relationship between Darcy's friction factor and Reynolds' number that is still in use today. If Colebrook's system of equations is plotted on log-log paper (as was done by Moody, 1944), the curves have some very distinct features. Of importance to the subject at hand is the relative response of friction factor to Reynolds' number at a given relative roughness. Simply stated, a pipe can appear to be either smooth or rough, depending on the flow conditions. As the Reynolds' number increases, the friction factor decreases at a decreasing rate until it becomes nearly a constant value. At this point, the flow is said to be "wholly rough." It is upon this condition that many traditional ventilation solution methods depend. For calculating pressure drops in a mine entry, Atkinson's equation is much more popular than the Darcy equation. Both of these formulas describe the same phenomenon and so have similar forms and functions. The K-factor in the Atkinson equation is equivalent to the Darcy friction factor and can be related by simply changing units, equating the pressure drops, and canceling like terms. A generalized form of this relationship is presented below as equation 1. K = yf/28,800g = [q]f/28,800 (1) where K is Atkinson's friction factor in kg/m3 (lb - min2/ft4), Y is the specific volume in Nt/m3 (lb per cu ft), p is the fluid density in kg/m3 (slugs per cu ft), g is the acceleration due to gravity (9.8 m/s2 or 32.2 fpsz), and f is Darcy's friction factor, which is unitless. The objective behind Eq. 1 is to show the strong correlation between K and f. Since these two quantities differ only by a constant (q]/28,000), the assumed independence of K-factor and Reynolds' number is suspect in light of the known response of f. Unfortunately, the formulation does not provide information concerning the actual relationship, as entry geometry likely plays a major role in the response curve. Only an indirect indication that such a relationship might exist is provided. Previous work on this subject was performed by Thomas Falkie (1958). The study involved a laboratory model composed of sections of straight, steel duct and a range of Reynolds' numbers from 15,610 to 137,200. Results from this work show a variation in friction factor with Reynolds' number in much the same way as it was found to vary in pipes. Over the range of velocities examined, a decrease of approximately 38% in K-factor was observed. This previous experience provides additional incentives to investigate the phenomenon under field conditions. Past model studies done at the University of Utah by Ozukurt (1945), Biron (1944), and Greenhalgh (1942) present similar evidence of this variability. More recently, Kharkar's (1974) study of coal mine friction factors contains similar indications that K-factor is not constant in all situations. Taken together, the data

Jan 1, 1988

By J. D. Allen

The Concord Mine Coal Preparation Plant of United States Steel Corporation, located near Bessemer, Alabama, began operations in June, 1950. The basic cleaning circuit consisted of a Chance Cone for cleaning the 2-inch x 3/8-inch fraction and concentrating tables for cleaning the minus 3/8-inch coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable (Figure 1), 85 per cent passing three mesh and 25 per cent passing 28 mesh, there was a considerable amount of fines passing through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-foot diameter hydro-separators with the underflow returning to the dewatering screens and the overflow going to a 175-foot diameter thickener for water clarification, (Figure 2). As might be expected, there was a considerable amount of recirculation of the minus 35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20 per cent. Further reduction to approximately 11 per cent was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a smaller percentage of the coal previously used at the coke plant, the high moisture and fluctuations did not seriously hamper coking operations.

Jan 1, 1966

By Justin Jensen, Luis Moya, Jose Carlos Durazo, William Szolga, Tyler McCallum, Tim Doubleday

Sulfuric acid mist is an undesired by-product of the copper electrowinning process, caused by oxygen evolution at the anode which entrains droplets of the acidic copper electrolyte solution. As the oxygen moves to the surface of the cell, these droplets become aerosolized resulting in acid mist. The addition of chemical anti-misting agents to the copper electrolyte is a common mitigation technique. This paper details Syensqo’s laboratory development of a new environmentally friendly acid mist suppressant, ACORGA® EW98. The product exhibits excellent acid mist suppression and it is fully compatible with the adjacent solvent extraction process. Lab and pilot test results are reviewed ahead of future planned industrial trial testing.

Feb 1, 2025

By Ing. E. h. Martin Herrenknecht, Werner Burger

In recent years, there has been a dramatic increase in the number of machine driven soft ground tunnelling projects. This increase is largely due to the technological development of slurry and EPB Shield systems. A new generation of soft ground tunnelling machines, markedly different from those of five years ago, now overcomes ground conditions that until now were too costly and impractical to undertake. The paper reviews the latest soft ground tunnelling machine developments in material transport, guidance and control, seismic surveying, soil conditioning, settlement control, cutting tool applications and variable mode operating systems. Specific projects where this technology has been applied will be highlighted.

Jan 1, 1999

By H. Wen, X. Zhai

"The Jurassic coal fields which lay in west China are the major energy base and contain half of coal resources in China. Due to the gather and degeneration rules, the spontaneous combustion characteristic of Jurassic coal is distinguished with permo-carboniferous coal, which needs to be studied deeply. Programmed heating experiments of five Jurassic coal samples and three permo-carboniferous coal samples from different primal coal fields in West China were conducted to identify the characteristic parameters in the low temperature stage of oxidation and spontaneous combustion. The experiments were carried out under non-isothermal heating conditions up to 180? at the heating rate of 0.33?/min in an air atmosphere. The result showed that oxygen consumption rate, CO gas production rate and heating intensity of all coal samples increased with the rising of the temperature, which of the Jurassic coal was higher than that of Permian-carboniferous coal. The C2H4 gas of Jurassic coal generated earlier, more than that of Permian-carboniferous coal in the process of oxidation and spontaneous combustion. It indicated that the Jurassic coal was easier to be oxidized and spontaneous combustion and the index parameters of spontaneous combustion were different between the Jurassic coal and permo-carboniferous coal.INTRODUCTION Coal was the foundation of industry development, and occupied 70% of primary energy production and consumption structure in China. According to the data of the 3rd coalfield prediction, 39.6% of the total coal resources were located in northwest Jurassic coal field in China [1], where the quality of coal was excellent. The study of northwest Jurassic coal already dated from the 80s of the 20th century, about coal rock composition, coal metamorphism [2], coal-derived hydrocarbons, coal structure [3], etc. The results of these studies showed that the composition and properties of Jurassic coal was obviously different from Permian-carboniferous coal, as well as the characteristic of spontaneous combustion [4]. As a result, the spontaneous combustion characteristic of Jurassic coal particularly needed to be studied. Now more and more methods could be conducted to test the characteristics of coal spontaneous combustion, for example, thermal analysis technology [5-7], programmed heating experiment [8-10] and coal spontaneous combustion experiment [11,12]. In these methods, programmed heating experiment could be conducted to determine the oxygen consumption rate, CO gas production rate and heating intensity quickly."

Jan 1, 2015

By E. Sabina Brady

Over the next two decades there will be significant trade and development opportunities in China for mining, engineering, equipment, and construction companies interested in becoming part of the development of China's chemical and fertilizer industries. At last count, China's phosphate ore reserves of 11.8 Gt (13 billion st), ranked fourth in the world behind the US, the USSR, and Sahara-Morocco. However, a recent statement by the head of the Ministry of Geology and Minerals, Sun Daguang, claims that with increased prospecting in the last few years, China's phosphate reserves now rank first in the world. Whatever the actual size of its known and potential reserves, China's present phosphate processing capabilities fall far short of demand, while the substantial progress that has been made in this area points out the severity of the problems that still remain. Since 1949 China has developed 181 mines and increased its phosphate concentrate production from 10 kt (11,000 st) to 10.86 Mt (11.97 million st). By the 1980s, China was the third largest chemical fertilizer producer in the world-although this claim is slightly misleading as China's nitrogen/phosphate potassium ratios are far from average world ratios and even further from US standards. According to the Sixth Five Year Plan promulgated in 1982, the country's development plans emphasize the expansion and upgrading of key energy and industrial sectors, including that of fertilizer production-specifically phosphate and potash. Within the framework of the plan, the Ministry of Chemical Industry's development priorities are to: • Increase potash production by 150% to 50 kt (55,115 st). • Raise phosphate fertilizer production 21.2% to 2.8 Mt (3.1 million st), 46 kt (50,705 st) of which will come from new projects constructed and completed within the Sixth Five Year Plan, with projected new production of phosphate concentrate and complex fertilizer in the next decades totaling 500 kt (551,146 st). • Commence work to increase phosphate ore production by 8.33 Mt (9.18 million st). Facilities for 2.43 Mt (2.68 million st) will be completed and come on stream by 1985. • Commence work to increase iron pyrite ore production by 3.69 Mt (4.07 million st), facilities for 2.9 Mt (3.2 million st) will be completed and come on stream by 1985. • Verify 600 Mt (661 million st) of new phosphate ore reserves. Since the promulgation of the Sixth Five Year Plan, Chinese authorities have announced that 70 key construction projects will receive top priority in the implementation of the plan. These projects include five in the chemical industry area, including the construction of four fertilizer plants in Urumqi (Xinjiang), Zhenhai (Zhejiang), Beijing, and Lucheng (Shanxi), and a pyrite mine in Yunfu (Guangdong). In addition, by 1985 the state will expand or construct three major phosphate mines: Wangji in Hubei, Kaiyang in Guizhou, and Kunyang in Yunnan. Fertilizer Ratios In 1982, China's fertilizer production was slightly higher than 12 Mt (13.2 million st) and consisted of 80% nitrogen, 19% phosphate, and 0.19% potassium. By 1985, state officials project that fertilizer production will reach 13.4 Mt (14.8 million st) and consist of 78.4% nitrogen (10.5 Mt or 11.6 million st), 21.2% phosphate (2.8 Mt or 3 million st), and 0.39% potassium (52.3 kt or 57,605 st). To attain the world average using the country's 1985 projected production level for nitrogen, China will have to double its 1985 phosphate production to 5.76 Mt (6.35 million st) and increase its 1985 potassium production almost 80 times to 4.1 Mt (4.5 million st). These numbers demonstrate the seriousness of the fertilizer production problem in China today and the long-term nature of the problem's solution. Development Examples Yunnan is the third largest phosphate-rich province in China with verified deposits of 1.9 Gt (2.1 billion st). Despite this abundance, the province only mines around 3 Mt (3.3 million st) of phosphate rock annually. In June of this year, Yunnan announced its intention to initiate 39 development projects within the next two and a half years, requiring an estimated $200 million worth of foreign investment. The three areas receiving the most emphasis will be:

Jan 9, 1983

By E. J. Hammer

In the crushing and grinding of metallics for beneficiation, the sizing is normally done to liberate the metals or sulphides for further processing to improve recoveries of the basic metals or minerals. The objective is to reduce the ore in size through various closely controlled stages to that degree of fineness which gives an economic liberation of valuable mineral, but which avoids as much as possible the production of sliming fractions. A different philosophy applies to the crushing and grinding of Gypsum. Our requirements normally demand controlled grinding and/or crushing of the material not only to a fineness suitable for further processing of the mineral into end products, but to produce various sizes of material which are them- selves saleable products. The majority of our tonnage ultimately ends up in stucco for Wallboard. Therefore, our mineral reduction is normally designed toward this end, but it is done in a manner that permits drawing off inter- mediate products to meet various Customer requirements. This forces us into compromises at times in our equipment installations, and our equipment must sometimes be more versatile and complex than we would like it to be. We try to process our basic rock, Gypsum, for the most efficient size reduction. We market 5 to 6 different sizes intermediate to the end product, which generally is the fineness of material to be used for stucco for Wallboard, and we do this with controlled crushing, grinding and sizing cycles of the material. To summarize, we use a different philosophy of crushing and grinding than the metallic field which uses comminution or crushing and grinding to improve recovery, whereas we choose our equipment to crush and grind primarily for product performance.

Jan 1, 1969

By Brent A. Elliott, J. Richard Kyle

This article reviews the production trends of industrial minerals since 2000 for Texas, the leading U.S. producing state of industrial minerals with a total value of $5.2 billion in 2017, equivalent to 6.9 percent of all U.S. minerals value. Most current Texas industrial-mineral value comes from the production of cement, crushed stone, industrial sand, and construction sand and gravel. Construction material consumption is concentrated in the 25 metropolitan areas of the state, with production of industrial minerals in nearby counties. With Texas’ population projected to reach 50 million by 2050, continuing in-state development and production of industrial minerals will be required to meet in-state and regional demand. Texas’ most rapidly growing production of industrial minerals is industrial sand to supply proppants for multiple unconventional petroleum plays. Texas’ favorable geology and economic factors provide opportunities for the identification and development of new industrial-mineral production sites. Repurposing of former industrial-mineral production sites for post-production development likely will increase as efficient land use evolves. Understanding the geologic, economic and societal framework of industrial-mineral resources will facilitate more informed decisions about the complex issues that the region will face, including effects of sea-level rise on coastal infrastructure.

By Pengfei Wang, Guorui Feng

"With the depletion of easily minable coal seams, less favorable reserves under adverse conditions have to be mined out to meet the market demand. Due to several historical reasons, a large amount of remnant coal was left unrecovered. One such case history occurs with the remnant rectangular stripe coal pillars using partial extraction method at Guandi Coal Mine, Shanxi Province, China. The challenge that the coal mine is facing is that there is an ultra-close coal seam right under it, with an only 0.8 to 1.5 m sandstone dirt band in between the two. The simulation study was carried out to investigate the simultaneous recovery of upper remnant coal pillars while mining the ultra-close lower panel using longwall top coal caving (LTCC). The remnant coal pillar was induced to cave in as top coal in LTCC system. Physical modelling shows that the coal pillars are the abutments of the stress arch structure formed within the overburden strata. The stability of overhanging roof strata highly depends on the stability of the remnant coal pillars. The gob development (roof strata cave-in) is intermittent with the cave-in of these coal pillars and the sandstone dirt band. FLAC3D numerical modelling shows that the multiple seam interaction has a significant influence on mining-induced stress environment for mining of lower panel. The pattern of the stress evolution on the coal pillars with the advance of the lower working face was found. This demonstrates that the stress relief of a remnant coal pillar enhances the caveability of the pillars and sandstone dirt band below them.INTRODUCTIONChina is one of the world’s coal-rich countries. Coal has played a significant role in the growth of China’s economy. Coal reserves have been mined commercially in China for over one hundred years. The demand for coal in China is still going to grow at a relatively high rate (BP Energy Outlook, 2019). Long-term large-scale and intensive coal mining activities have created tension between increased demand and limited resources (Bai et al., 2018). Easily minable coal seams such as sub-horizontal, tabular, and laterally extensive coal seams are being depleted, and therefore the remaining reserves are becoming less favorable. However, in many situations, the coal reserves under adverse conditions have to be mined out to meet the market demand for energy.Due to sedimentary environments and geological conditions, many coal seams are interspersed with sedimentary bands, or partings both within an individual seam and between seams. These bands and partings lead to appearance of ultra-close coal seams, as well as giving rise to considerable variation in their structural and mechanical properties (Ghabraie and Ren, 2016). Difficulties are encountered in the mining of such coal seams. If ultra-close coal seams are mined sequentially, that requires the design of a mining system for each individual coal seam; also, a large number of gateroads have to be excavated, which is not a high-efficiency option. If ultra-close coal seams are mined at a great mining height at once, for instance, using longwall top coal caving—a longwall mining method that is widely used in China for the mining of ultra-thick coal seams—then the location and characteristics of the band would have a significant influence on success of their extraction."

Jan 1, 2019

By A. F. Peterson

There is no single mining problem at Benson that does not exist at some other mine. There are four, however, that require special attention primarily because they occur together and have an influence on each other. These are the nature of the mineral occurrence, the shape of the ore body, the operating schedule, and the climate. It is the purpose of this paper to describe mining practices in relation to these four factors. Iron ore was first noticed in the Star Lake area early in the nineteenth century. Prior to Jones and Laughlin leasing the facilities built by the Defence Plant Corporation, several companies tried to mine the ore body but gave it up as uneconomical. While there is a little high grade (40%) magnetite, most of the ore contains 20 to 25% iron and not enough was known prior to World War II to design a profitable operation. By 1943, and certainly in the years that followed, technological developments in ore dressing and mining not only put the magnetite into the category of a commercial ore, but made possible the concentration of the non-magnetic iron mineral, martite. This last development nearly doubled the ore reserve. Jones and Laughlin bought the DPC holdings in 1946 and has since expanded the plant to its present capacity of 4,400 gross tons of concentrates daily or 1,600,000 gross tons per year. Magnetite makes up 62% of this production at the present time, but it will be necessary before long to bring martite production up to about 45% of the total because of the ratio of the two ores in the reserves. To keep the plant supplied, 14,000 to 15,000 tons must be mined and crushed daily, with a ratio of concentration that varies from 2.8 to 3.4. The ore body is 12,000 feet long and varies in width from 600 to 1,500 feet. The waste rock is, for the most part, a granite gneiss, and the overburden, of which little is left, is a glacial drift sand. For the entire reserve, there is a half ton of rock for every ton of concentrate, but the stripping ratio is more than one to one at present because of the existence of more rock in the upper mining levels in relation to the ore. The dirt stripping or development work that cannot be handled by company facilities is contracted to an outside firm. The need for this diminishes every year and will soon disappear. The deposit looks like a "J" in plan, with the long leg running approximately north and south and the short leg to the west. The primary crushing plant, consisting of a 54" gyratory followed by two 18" gyratories and a 1,500 foot conveyor belt to the fine crushers, is located on the third level where the long and short leg of the mine meet. The widest part of the pit lies just the north of the crusher. The mine is operated on a lease that expires in 199l0 There are two fee owners, the Benson Iron Company, which owns slightly overhlf of the reserves, and the Newton Falls Paper Company, which owns the balance. There is no appreciable difference in the mining on the two fees, so the ore is removed in strict proportion to calculated reserves during each year. Basic mining equipment consists of eight 45 yard electric shovels, a fleet of twenty-five 22 ton end dump trucks, eleven churn drills for nine inch blast holes, and two small percussion drills for four to five inch holes, There are the normal auxiliary items, such as dozers, graders, wagon drills, and two drop-ball cranes. Power is purchased and, where practical, is used at 4100 volts. Pit drainage pumps can handle a maximum of 11,500 GPM from the several sumps, but water is a problem only during the spring or when a sudden thaw follows a heavy snowfall.

Jan 1, 1958

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION This method is a variation of cut-and-fill mining where either the wall rock or the vein is too unconsolidated to permit safe mining by conventional cut-and-fill methods. Basic development consists of driving a 2.4 x 2.7-m (8 x 9-ft) haulage heading laterally in the footwall side of the vein. Crosscuts are driven over to the vein at 91-m (300-ft) intervals. Then the vein, at each inter¬section, is mined out to a distance of about 9 m (30 ft ) above the track level. After the installation of an ore chute, scrams or intermediate drifts are driven in both directions along the vein. Mining then starts imme¬diately below the level bounding the upper limit of the stope. A cut varying between 3 and 4.2 m (10 and 14 ft) in depth and mined for a distance of 45.7 m (150 ft )along the strike is taken from the orepass in each direction (Fig. 1). In this mined-out void, the floor of the cut is equipped with 203 x 203-mm (8 x 8-in.) caps hitched into the wall with steel saddle hitches installed on 1.5-m (5-ft) centers. Double wood stringers, 152.4 x 152.4 mm (6 x 6 in.), are then installed on 1.2-m (4-ft) centers longitudinally down the length of the stope. Reinforc¬ing wire mesh is also placed, overlying each mat of timber. Directly above the stringers, stulls are installed from hanging wall to footwall to hold the timber in place during the sand-filling operation. Then a cement¬sand mixture in a ratio of about 1:10 weight is poured to a depth of about 2.4 m (8 ft). The entire cycle is then repeated down to the scram drift. Another variation of timbering is illustrated in Fig. 2. There is a vein width of approximately 5.5 m (18 ft) with the same unconsolidated ground conditions. The primary difference between handling this situation and the previously described undercut-and-fill method is that standard timbered sets are installed in each excavated stoping void rather than stulls. Once again the basic method is to work down the ore block from an upper timbered drift to a lower timbered drift. Cuts are taken from a timbered raise with a chute on the stope side. Each piece of ground excavated is essentially two sets high, 5.5 m (18 ft), by two sets wide, 5.5 m (18 ft), by the length of the cut along the strike of the vein. The timbered sets are 2.4 x 2.4 x 2.4 m (8 x 8 x 8 ft). The net result is, therefore, two sets of timber on a top floor separated by doubled-up 76-mm (3-in.) lagging from

Jan 1, 1982

By FHATUWANI SENGANI

The understanding of yielding pillar behavior has been well documented in terms of pillar strength using numerical simulations and empirical formulas, but the understanding of how fracture propagates in a matured yielding pillar is not well established. A new empirical summation chart of fracture distribution along the matured yielding pillar is presented in this paper. The chart was developed using ground penetrating radar (GPR) supported by borescope observations, focusing on monitoring the distribution of extension fracture.

By Kurt Egger, Emily A. Baker

Rehabilitation work at the Cameron Run Tunnels entailed the restoration of seven heavily deformed, approximately 69 m long, steel liner plate supported culverts through a CSX Railroad embankment near Alexandria, Virginia. A custom fabricated expander, equipped with four 200-ton hydraulic jacks on two expansion arms was used to push back the liner plates encroaching into the proposed tunnel profile and install the steel set support. In a second phase the tunnels were then lined with 16 cm of fiber reinforced shotcrete. Geotechnical instruments both in the tunnels and on the railroad embankment were used to monitor the effects of the rehabilitation work on the two CSX Railroad tracks above the tunnels. Freight and passenger trains were required to run uninterrupted and at maximum speeds throughout construction.

Jan 1, 2003