Search Documents

By Jack T. Work

Spiraling costs in every segment of the open-pit mining cycle is a fact of life that every operator must reckon with. The introduction of various shock absorbing devices for rotary drilling is one recent innovation that may significantly reduce overall drilling cost, increase drill availability, and lower maintenance requirements. In a recent all-inclusive test in taconite ores, shock absorbers on Bucyrus-Erie BE 60R and Gardner¬Denver GD 120 rotary drills were directly responsible for overall savings of up to $41.06 per hour. What is It? A shock absorber is simply a device installed between the rotary drive head and drill steel that cushions the two. It functions in the same manner as springs and shocks on an automobile. Some benefits associated with use of the tool are readily apparent on a daily basis; other benefits are realized over longer time intervals and through continued use. A properly designed shock absorber will: •protect the drill from severe vi¬brations, improve rock bit performance, allow application of the best weight-on-bit and rotating speed under all drilling conditions, •function effectively over a wide range of applied bit weights, • have a spring rate soft enough to perform its primary function of absorbing both rotary and vertical vibrational forces generated by rough drilling, •be reliable and subject to as little maintenance as possible, •be easy to install and remove, and • be of such an economic benefit so as to offset the added expense of its application. A shock absorbing tool developed by BJ-Hughes Inc. was used in a recent test. The "Smoothdrill" is just one of the products currently available. This unit absorbs both rotary and vertical shock loads and has no mechanical parts so lubrication is unnecessary. A rebuild of the unit consists of removing the worn rubber element and inserting a new element, an operation taking less than one hour. Minimizing Vibrations Severe vibrations on a blasthole drill operating in broken and discontinuous formations have visible effects. These vibrations often cause structural damage when allowed to' continue, resulting in fatigue cracks in the mast and related structural components in the drill. When rough running formations are encountered, drilling must be interrupted and possibly shut down. Usually, the drill operator resumes drilling using less down pressures and various rotational speeds until firmer drilling is encountered. An effective shock absorber can substantially reduce these vibrational forces so more down pressure can be applied in bad ground. It is generally accepted that longitudinal vibrations and cyclic forces are more effectively reduced if a tool is designed to incorporate a relatively "soft" shock absorber. The softness of any shock absorbing tool is best judged by its spring rate-the weight required to produce a given amount of deflection, commonly expressed in units of kg per mm or pounds per inch of deflection. All shock tools use a resilient member such as rubber springs, steel springs, fluid, or gas springs to absorb

Jan 4, 1980

By Isobel Yeo, Luca Cocchi, Sven Petersen, Nico Augustin, Sean Plunkett, Ingo Klaucke

Exploration for seafloor massive sulfides is currently mainly focused on investigation for active hydrothermal vent fields. However, most of the resource potential is thought to be related to inactive, large deposits that had enough time to accumulate sufficient tonnage. At the same time, ageing of these deposits will ultimately result also in burial acted by either sediments and/or volcanic deposits. We currently lack the technologies to explore for these deposits in a time- and cost-efficient manner. In the fall of 2012 we used a number of AUV-based technologies to explore and image a sulfide occurrence at the Palinuro Volcanic Complex in the Tyrrhenian Sea (Mediterranean Sea; Fig. 1) where sampling and drilling have documented a buried polymetallic barite-pyrite dominated site (Petersen et al., 2014). Sulfide mineralization is here covered by volcaniclastic and pelagic sediments and only red sediment staining and the presence of few tubeworm bushes indicated recent hydrothermal activity - black smoker venting is absent. We used AUVbased high-resolution bathymetry, sidescan sonar imaging, subbottom profiling, as well as magnetics to describe, in a quantitative way, the previously known sulfide-bearing areas as well as to successfully explore for new hydrothermal sites including large chimney structures (Figs. 2). Additionally chemical sensors (CTD, Eh, turbidity) investigated the water column for signs of hydrothermal activity in areas not previously investigated, but at the end, only weak anomalies were found in the southern part of the summit.

Sep 1, 2014

The Subtropolis mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, Ohio. In February 2018, mine management began implementing a heading reorientation to better control the negative effects of excessive levels of horizontal stress. The conditions in the headings improved, but as expected, stressrelated damage concentrated within crosscuts. The mine operator has worked to lessen the impact of the instabilities in the outby crosscuts by implementing several engineering controls. With the implementation of each control, conditions were monitored and analyzed using observational and measurement techniques including three-dimensional (3-D) LiDAR surveys.

Jan 7, 2020

By Nasser Madani, SULTAN ABULKHAIR

The abstract of the paper discusses the challenge of quantifying iron content in a coal deposit in Kazakhstan. The iron dataset is limited, coming from only three drill holes and some stope samples, while a large amount of geological information is available from legacy drill hole data. The paper proposes a workflow using multiple-point geostatistics to model geological domains and two-point geostatistics to model iron content within these domains. The results show that the direct sampling (DeeSse) algorithm effectively reproduces the complex seam layers, and sequential Gaussian simulation models the iron within each domain.

Mar 30, 2022

More than 410,000 visitors from 171 countries helped bauma ’04 set new attendance records at the world’s largest construction machinery and mining technology show. The show, held in Munich, Germany March 29-April 4, marked bauma’s 50th anniversary. At the last bauma show in 2001, attendance was about 406,000 people from 157 countries. At bauma ’04, international attendance increased to 31 percent from 27 percent in 2001. In addition to record-setting attendance, bauma ’04also attracted 2,801 exhibitors, up from 2,341 in 2001. Exhibitors came from the United States, Europe, China, Japan and the Middle East. Exhibitor space topped 500,000m2 (5.4 million sq ft), another record. And, for the first time, there were more foreign exhibitors than German exhibitors, show organizers said.

Jan 1, 2004

By David Belknap, Clay Haynes, David Egger

Rehabilitation challenges were met nearly two months ahead of contract schedule for the Design-Build, Fast Track Scituate Aqueduct & Tunnel project in Cranston, Rhode Island. The aqueduct and tunnel were built in the 1920s and consisted of three sections—a 2.3 m diameter reinforced concrete section that extends approximately305 m before it transitions to a horseshoe-shaped 2.3 m wide by 2.1 m high cast-in-place concrete tunnel that continues for approximately 5.3 km until it transitions back to a 2.3 m circular section that extends approximately 1.9 km to the end of this project. Major repairs were required to assure sustained operation of this water supply tunnel.

Jan 1, 2005

By S. Dessureault, Z. Gavelan

As globalization continues, sustainability and social responsibility has become essential in foreign mining investment. However this global trend and the increasing acceptability toward the globalization process, viability and sustainability are not always achieved. Viability and sustainability of mineral projects is dependant on the social and political environment of the region where the mining venture is located and is based on the interaction between the mining entrepreneurs, national-local government representatives, communities, grass-roots groups and independent civil organizations. These are the organizations, which play the acting roles on the viability of mining projects and are the main source of socio-political risks for the project. Throughout the decision-making process to invest in a mineral project, socio-political risks are quantified using a set of measurable variables. Nevertheless, these risk measures should be dependent on specific industries. Two mineral projects, even in the same mining district, may have significantly different political risk profiles based on their own socio-political variables. This paper describes a methodology that takes into account local social and political variables in defining a project-specific’s political risk profile. This contrasts with more typical political risk measures that focus on the country’s overall risk profile. Mining operations must operate on a local scale necessitating the development measure that considers more local variables.

Jan 1, 2004

By L. K. Marshall

The importance of high quality underground mine ventilation is readily apparent. The principles of primary and auxiliary mine ventilation, however, are sometimes less readily apparent. The first article in this two-part series discusses some general aspects of primary and auxiliary ventilation. Next month's article will detail considerations involved with auxiliary mine ventilation.

Jan 1, 1982

By O. A. Bascur

The lack of integration of mining and metallurgical information with sufficient detail for analysis causes inefficient operation and hence sub-optimal energy and water use. It is difficult to analyze the performance of mining and metallurgical processes without an integrated view of mine transactions, stockpile inventories, process flows and assays. To take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. This paper presents an infrastructure with advanced tools that sift through available data, identify and eliminate gross errors, and transform the data into business information for continuous improvement and optimization. Collaboration is a key component of improving efficiency of energy and water use, and the evolution of Web technology enables collaboration and troubleshooting of plant information to more quickly act on issues to reduce wasteful operation. Keywords: Mine Concentrator Optimization, Real Time Performance Management, Data Unification, Integration of Operational and Business systems, Mass and Energy Balances, Real Time Web Services, Equipment Availability, Efficiency.

Jan 1, 2009

By L. Echeverri

Research studies have shown that the flow within feedwells displays a vortical structure and high velocities at the locations where standard tangential inlets force its way into the feedwell swirling flow, producing high local shear rates and flow non-uniformities. These hydraulic deficiencies can be attributed to the discrete feeding through a few entrances, usually one or no more than a few tangential feedpipes, which practically project jets into the vortex within the feedwell. The main consequences are unequal flocculation with aggregates subjected to different amounts of shear and a non-uniform discharge from the feedwell. This paper presents results on the application of CFD and small-scale models to develop a new design that overcomes these problems by using an involute shaped inlet that converges around the feedwell. The result is a new feedwell with enhanced hydraulics that perfectly couples with the FLSmidth E-Duc® Feed Dilution system by protecting the flocculated aggregates that have been carefully produced upstream, and that favors uniform sedimentation conditions within the thickener thanks to a uniform discharge, while maintaining a practical and trouble-free geometry with excellent turndown.

Jan 1, 2012

By R. P. Sloan, A. S. Whitford

In November 1999, CCI's Empire Iron Mining Partnership and MinnovEX Technologies Inc. developed an expert system for advanced control of their Empire IV Grinding Section. Empire IV is comprised of three autogenous Primary Mills and six autogenous Pebble Mills, with a single Pebble Crusher and high pressure Roll Press. The challenges of controlling and optimizing three distinct grinding lines that are inter-woven by a pebble crushing circuit were met with innovative and unique solutions. This paper will detail the approach employed at Empire and will focus on the aspects that make this application unique.

Jan 1, 2001

By X. Cui, H. Ding, J. Wen, Q. Gu

This study is a continuation of previous work designed to further explore the mechanism of the bioleaching of sulfide concentrate at neutral pH by heterotrophic bacteria Bacillus megaterium QM B1551. The concentrate contained 13.2 percent nickel (Ni) and 0.2 percent cobalt (Co), which presented primarily as pentlandite and pyrrhotite. Contact and noncontact bioleaching experiments were conducted with finely ground ore at an initial pH of 6, resulting in 44.7 percent of Ni and 38.2 percent of Co leached in the contact-bioleaching treatment. Oxidation experiments of sulfur, thiosulfate (S2O32−) and ferrous ions (Fe2+) by cell membrane were performed to verify whether sulfur transferase, thiosulfate quinone reductase and enzyme cytochrome B558 on the surface of the bacteria could be expressed to oxidize the sulfide. The results show that thiosulfate quinone reductase and cytochrome B558 could be expressed to oxidize S2O32− and Fe2+ to SO42− and Fe3+, respectively.

By Colin P. Pigott

The paper describes a variety of existing techniques and equipment which when combined together permit faster and cheaper drilling of shafts in soft to medium strength formations. Drilling fluid circulation, methods of hole stabilisation and bit design, including the advantages of flat bottomed and conical bits, shrouds and skirts, tungsten carbide, long tooth and disc cutters are considered. The principles of rock chip transportation and bottom hole cleaning are described together with a new and very efficient fluid circulation system which was invented by the author.

Jan 1, 1985

By Refik Elibay, Lawrence A. Williamson, George D. Barnes

Under an extremely aggressive schedule, final design of 13.5 km (8.4 miles) miles of 8.2 m (27 ft) diameter deep rock tunnel, 322 ML/day (85 million gallons / day)submersible pumping station and associated facilities were accomplished ahead of a federal court mandated consent decree schedule. Challenges overcome by the project team in enabling timely completion of the construction documents will be presented. Discussion includes evolution of final design, consideration of future O&M requirements, and risks identified for construction and operations, together with measures to manage and proactively prepare for such risks.

Jan 1, 2005

By Kwang ‘Min’ Kim, Paul T. Behum

The Old Bevier Aerobic Wetland in Macon County, Missouri, was constructed between 1990 and 1991 by the Missouri Department of Natural Resources’ Land Reclamation Program for the purpose of treating acid mine drainage (AMD). The principal source of the AMD is from an underground mine that operated during the 1920's through 1950's, which was partially exposed during surface mining in the 1960’s. Limestone bedding of an AMD collection system provided alkalinity similar to an anoxic limestone drain (ALD). Because the original aerobic wetland failed when a critical dilution water supply became unavailable, the total acidity of the AMD overwhelmed the limited neutralization ability of the aerobic wetland. The aquatic vegetation deteriorated and treatment became ineffective. The Missouri Land Reclamation Program with the assistance of the Office of Surface Mining, Mid-Continent Regional Coordinating Center rehabilitated the Old Bevier Aerobic Wetland in 2001, incorporating newer technologies to improve the performance. The new system, Old Bevier II treatment facility, consists of a 2-stage vertical flow pond (VFP) with associated oxidation cells and aerobic wetlands. This paper discusses the performance of this passive AMD treatment system, updating an earlier report. The new treatment system has operated with nearly continuous net alkaline discharge and a high iron removal rate. Treatment improves during warm months when emergent vegetation is fully established and biologic activity is greater. Reduction in system efficiency is evident during winter months.

Jan 1, 2005

By Ö. Kaya

The removal of gangue minerals from three different graphite ores (Inebolu, Akdag?madeni and Çoraklidere) from Turkey by acid leaching was studied. Acid leaching experiments were applied to the flotation bulk concentrates, which were obtained in determined optimum conditions after preliminary flotation tests. The effects of acid type, acid concentration, leaching temperature and leaching time on the dissolution of gangue minerals were studied. The most suitable leaching conditions were determined to be 20% HCl + 4% HF for acid type and concentration, 85 ºC for leaching temperature and 4 hours for leaching time. After removing the gangue minerals at these optimum conditions, the total carbon contents of the samples from Inebolu, Akdag?madeni and Çoraklidere increased from 23.51% to 40.07%, from 37.93 to 60.47% and from 42.28 to 59.47%, respectively.

Jan 1, 2009

By G. Karahalios

Industrial minerals have always enjoyed an important share in the technological growth of any country in the world. Today, extraction and trading of industrial minerals has expanded, but is also subject to stricter environmental guidelines. This paper presents the current status as well as the growth potential in the exploitation of industrial minerals in the countries of the south eastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, F.Y.R.O.M., Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. More specifically, annual production figures per country are presented for1992-1998. These figures are compared to each other and, where applicable, to world production figures. Trading of industrial minerals from these countries to Europe and the world and its effect to the local economies is also evaluated were such data is available.

Jan 1, 2000

By David E. Nicholas, Steven R. Dismuke, Paul F. Cicchini

The Buick mine, located 195 kilometers (120 miles) southwest of St. Louis in the Viburnum Trend, is owned and operated by Homestake Mining Company. The mine produces lead and zinc ore from a room and pillar mining method at a depth of approximately 335 m (1 100 ft). The Buick orebody typically averages 60 to 120 m (200 to 400 ft) in width with ore thicknesses ranging from 2.4 to 36.6 m (8 to 120 ft). The mine is divided in two; the halves are referred to as the North mine and South mine orebodies. The North mine orebody contains the higher grade ore; however, the developed reserves for the South mine orebody comprise about 60 percent of the total developed reserves for the Buick property. Existing pillars represent one-third of the total developed reserves.

Jan 1, 1986

By A. Sobhy

Froth flotation is a widely used, cost effective coal cleaning process. However, its high process efficiency is limited to a narrow particle size range between approximately 50 to 600 µm for coal and 10 to 100 µm for minerals. Beyond this range, the efficiency of froth flotation decreases sharply, especially for difficult-to-float coal fines of weak hydrophobicity (e.g., oxidized coal). This study was aimed at enhancing recovery of an Illinois fine coal sample using a flotation column featuring a hydrodynamic cavitation nanobubble generator. Nanobubbles that are mostly smaller than 1 µm can be formed selectively on hydrophobic coal particles from dissolved air in fine coal slurry. Results indicate that combustible recovery of a -150 µm coal was increased by 5-50% for different size fractions in presence of nanobubbles, depending on process operating conditions. Other major advantages of the nanobubble flotation process include lower collector dosage and air consumption since nanobubbles are produced from air naturally dissolved in water and they act as a secondary collector on particle surfaces, thereby resulting in considerably lower operating costs. Key words: Cavitation; coal; froth flotation; nanobubble.

Feb 27, 2013

By Christopher J. Bise

INTRODUCTION Perhaps no other area reflects the art as well as the science of mining-engineering design quite as obviously as strata control. This is due to the fact that the design of mining structures is difficult because rock rarely behaves as a homogeneous medium. Further, the original state of stress and the mechanical proper- ties of the in situ rock are somewhat difficult to deter- mine. However, those aspects that are hard to treat mathematically can and have been successfully approached by model studies and in situ measurements. This chapter will review the fundamentals of strata- control design and will provide examples of applications to typical problems. STRESSES AROUND MINE OPENINGS A close examination of Fig. 1 reveals that, prior to mining, stresses exerted in the overburden can be in both the horizontal and vertical directions. In the example problems of Chapter 1, it was shown that the maximum compressive stress (uv) at any depth (D) below the surface can be approximated as follows: [ ] Further, the lateral stress (oh) is related to the maxi- mum compressive stress by utilizing Poisson's ratio (µ): [ ] As soon as a heading is driven, such as the one in the coal seam shown in Fig. 2, the stresses shift to the sides, or abutments, of the opening. Clearly, these compressive stresses around the opening exceed the pre-mining conditions. The problem of designing an underground opening, therefore, is to determine the maximum stresses and to note if they exceed the ultimate strength of the rock. Table 1 lists several rocks with their corresponding strengths. Figs. 3 to 5 depict the boundary stress concentrations around circular, ovaloidal, and rectangular openings. M is the ratio of the horizontal stress to the vertical stress, or as defined above, p/(l-p). This text will concentrate on the state of stress represented by M = 0.33, which corresponds to the condition of no lateral deformation in a rock having a Poisson's ratio of 0.25. For an ovaloid with an opening width-to-height ratio of 2.0 (Fig. 4), the boundary stress concentrations are at their maximum values at the comers of the opening, with values in excess of 3.0. If the depth of overburden is 500 ft, then the maximum boundary tangential stress ([ ] ) of the ovaloid is: [ ]

Jan 1, 1986