Search Documents

By Raymond L. Jones

With the inauguration of the open pit operation in Bagdad, plans were formulated for a large scale leaching operation. Dump stockpiling was started almost immediately, but actual production was not initiated until the spring of 1961. Like all neophytes, we started something about which, on a commercial scale, we knew next to nothing, either dump preparation or leach procedure, and as a consequence, we are still paying the piper. True, we had been through an extensive laboratory pilot program, but it soon became apparent that there was considerably more to increasing solution volumes than simple multiplication. Had we initially possessed our present acumen, the Cyprus Bagdad plant could be operated more efficiently and at a better profit. During the past several years, the art of dump leaching of copper has improved in many ways, primarily because of the application of scientific principles gleaned from general mining practice. Rigid pH control and the use of atomic absorption techniques for rapid," accurate assaying have probably played a leading role in this respect, although we cannot overlook the other sophisticated electronic controls lending improvement to acid addition and pumping, better piping materials, and lastly, the more efficient use of our pregnant liquors. Thin too, the years of experience have given us a greater understanding of dump behavior in general; and, we can, to a greater extent, measure, predict, and avoid some of the idiosyncrasies inherent in every dump. However, it is my firm belief that we will still be confronted with unexplainable dump behavior as long as we are involved in leaching. We have found our dump to be a wonderful money bank, but one that is capable of yielding a wildly fluctuating profit.

Jan 1, 1975

By E. J. Jacques

A typical problem in ventilation networks with multiple fan systems is the possibility of them interacting. Multiple fan systems are no exceptions in complex tunnels, and may also be met in mines where underground fans are installed. When aiming at controlling a multiple fan system in a ventilation network, e.g. with a view to maintaining an acceptable air quality level, yet at minimum power consumption, transient flow conditions frequently occur. Although in most applications these transients are short compared to the time needed to achieve the planned actions on the ventilation, one should, however, keep in mind that it is important to avoid any bouncing effect between different (adjacent or distant) fan systems. Therefore a simulation of the unsteady-state flows could allow us to learn more about the propagation of transients within the network, and their possible secondary effects Among others, one question that often is raised, is to find out in which sequence and at what time schedule each of the fans in a network should e.g. be started up? Another typical problem, into which an unsteady-state simulation could provide some insight is the following: how should the facilities of variable pitch angle and/or changeable RPM of several fans operating in parallel be handled and combined in order to obtain a flow rate that changes gradually from zero to its maximum value i.e. the sum of the individual throughput flows of all the fans. The literature is not very abundant on the topic of simulating transient flows in networks. There is no doubt that numerical models have been developed (Pollak, Christensen, 1987), most of the time for particular applications (Wala, Kim, 1985), (Tanaskovic et al., 1984), (Schultz, Sockel, 1991), etc. The aim of this paper is to present a model that also simulates one-dimensional compressible flows in unsteady-state conditions with, however, the specific intent to handle networks with more than one fan. PROBLEM STATEMENT The mathematical model chosen to describe the unsteady flows in a ventilation network is based on the dynamic and continuity equations applied to each of its airways. The following basic assumptions are made : - the flow in the airway is considered to be one- dimensional, - - the flow is assumed to be fully turbulent, and hence the ATKINSON equation for calculating the friction losses will be applied. Whether this equation remains valid for transient state flows remains an open question. However, this may reasonably be assumed since the interesting flow frequencies are low. A discussion may be found in (Kämpf, 1987) ; - the airways are assumed to have a constant cross- sectional area along their length. If obviously this would not be the case, it is always possible to subdivide the concerned airway into sections for which the previous assumption holds. Applying the basic equations of mass and energy conservation, the flow in each branch may be described by the Euler equation for Newtonian flows.

Jan 1, 1995

By J. G. Groppo, B. K. Parekh

Eastern US oil shale contains approximately 10 to 12 gallons of oil per ton and 7 to 10% pyritic sulfur. Physical beneficiation of these low grade shales using froth flotation provides a high grade material that makes extraction of oil more economically attractive. The Alabama oil shale used in the present study contained 16.46% organic carbon and 14.5 gallons of oil per ton as determined by Fischer assay. Liberation size of the kerogen was estimated at 10 µm. `Ken-Flote' column flotation technology provided a high grade concentrate containing as much as 60% organic carbon. However, carbon recovery was about 60%. Carbon recovery was improved to 75-85% while maintaining concentrate grades in excess of 40% carbon by providing longer retention time in the column, which facilitated effective bubble-particle collision and attachment.

Jan 1, 1994

By C. I. Wilmot

The paper presents an update of the Paradise Peak mill after the first year of operation. Process revisions, equipment modifications and additions, and personnel requirements are discussed with a comparison to original design. All areas of milling are discussed including crushing, grinding, leach/countercurrent decantation (CCD), precipitation, refinery, and heap leach.

Jan 1, 1987

By T. Hollingsworth

The Boddington Gold Mine, located near Perth in Western Australia, has recently completed the construction of a new process plant. An overland conveyor system was installed to convey the ore from the primary crusher to the process plant. This paper will discuss the overland conveyor?s mechanical design including dynamic analysis and the selection of primary mechanical and electrical components.

Jan 1, 2010

By David E. Thompson, Wesley E. Stimpson

The Massachusetts Bay Transportation Authority (MBTA) Red Line Extension Northwest is currently in the early stages of construction. The 3.1 mile extension of the Red Line from the existing Harvard Square Station in Cambridge, Massachusetts to Alewife Brook Parkway in Cambridge, Massachusetts will include a large, near surface hard rock, rapid transit station chamber at Porter Square in Cambridge (Figure 1). [ ]

Jan 1, 1979

By Bobby P. Faulkner

Allis-Chalmers has combined a new heat transfer device, called the ROLLER GRATE, with a unique processing scheme, resulting in the ROLLER GRATE Oil Shale Processing System of Allis-Chalmers. In order to test both the process and the equipment, a batch Process Development Unit (PDU) ROLLER GRATE retort was designed and built. This unit vas designed with the flexibility to process shale over a wide range of test conditions in order to demonstrate the attributes of the oil-shale processing system. Instrumentation on the PDU and extensive sampling of the effluent streams permitted the PDU test data to be used in the design and scale-up of the process. Over 30 tests have been conducted with Colorado shale, and over 25 tests have been run with an Indiana shale. In addition, rests have been run with California and Utah tar sands.

Jan 1, 1983

By V. N. Kolesnikov

The gold-silver deposits of the northern Primorye region are located in the eastern part of the East Sikhote-Alin volcanic belt, where the belt overlaps the Kema island-arc terrain of the Aptian-Albian age. There have been four deposits and numerous mineralization points found in the NE-trending Kema metallogenic belt that is about 1000 km long and 100 km wide. The known mineralization is of epithermal type, controlled by faults, and concentrated in quartz, quartz-fluorite-adularia, and, less commonly, sulfide-quartz vein systems hosted by the Upper Cretaceous-Lower Tertiary volcanic rocks. The vein systems extend for hundreds meters along strike, varying from tens centimeters to 50-60 meters in width. They are surrounded by wide zones of low-temperature hydrothermal alteration containing some gold-silver mineralization for which the commercial value was not studied during the early exploration. The ore bodies contain from 1 to 50-80 ppm of Au and from 1 to 1000 ppm of Ag. Gold is native, associated with quartz, and represented by particles from tens of microns to 1 mm in size. Silver occurs in native form as a constituent of argentite, pyrargyrite, stephanite, and other sulfosalts. The test work carried out for three vein systems 20 years ago showed that gold might be easily and almost completely recovered from the ore by cyanide treatment. The paper describes the geology and mineralogy of the deposits, Salut and Primorskoye, that are the most studied properties of the Kema belt. It also presents the data available on disseminated gold-silver mineralization in stockworks, altered explosive breccias, and wide zones of low-temperature hydrothermal alteration. This mineralization should be explored for possible exploitation as large open-pit, heap-leach deposits.

Jan 1, 1998

By A. A. Jonke

The combustion of fossil fuels in a fluidized bed of calcined limestone particles is a potentially efficient and economically attractive process for the generation of steam for electric power production and other uses. The process results in greatly reduced emissions of both sulfur oxide and nitrogen oxide pollutants. Development work, evaluations and design studies are being carried out by various organizations under contract with the U. S. Environmental Protection Agency and the Dept. of Interior (Office of Coal Research). The AEC's Argonne National Laboratory is one of the principal participants in the development program under interagency agreements with EPA and OCR. This paper covers the principal reasons for developing fluidized-bed combustion, its advantages and disadvantages over conventional combustion methods, and some of the potential applications of the process. The participants in the multi-organizational program, the sponsoring agencies, the general status of development of the overall project, and the chief program areas that still require resolution are discussed. The main features of the program of work at Argonne National Laboratory and the results achieved so far are also included.

Jan 1, 1974

By Eugene Honeycutt, David Gallagher, R. E. Melley, Nick Madison

Drummond Co. Inc.'s Shoal Creek Mine slope conveyor is the highest lift, highest horsepower, highest tension conveyor system in North America. The system has a capacity of 4950 t/h (5500 tph), a vertical lift of 360 m (1180 ft) and a total connected power of 6000 kw (8000 hp). The mine will include 2 longwall machines and 5 to 7 development sections. Annual raw production will approach 9 million tly (10 million tpy). This paper describes the early investigation of system capacity, haulage system options, and the final selection of a single flight belt conveyor. It will review the basic system de- sign and equipment selected. Also included will be some highlights of the installation of the conveyor system.

Jan 1, 1996

By Stephen H. E. Phillips, Michael J. Beus

A pneumatic impact breaker is used to fragment the rock at the shaft bottom, replacing the drill and blast cycle. A backhoe-type mucker removes the broken rock. The operators are in protective cabs below the bottom work deck in the shaft. Preliminary testing has been accomplished at underground and surface test sites in Arizona. Seven, approximately 6.4 m deep by 7.3 m-diameter (21 ft by 24 ft) test holes, (a total of 45 m (148 ft)), were recently excavated in various rock types, including jointed and massive quartz monzonite and rhyolite. An average advance rate of .4 m/hr (1.24 ft/hr) has been achieved. This includes breaking and mucking the rock. Further data is being sought from an in-shaft demonstration.

Jan 1, 1981

By Lisa A. Banick, Robert A. Rubin

The lawyer's role in underground construction, certainly for the past 20 years, has been principally that of the advocate in disputes resolution. Disputes in underground construction have been steadily increasing, making the lawyer a more prominent participant in the underground construction process. It is widely believed, however, that this is not a salutory state of affairs. It is our thesis that lawyers ought not be eliminated from the process, but rather that their role should be changed. They should function as prophylactics rather than as swords, i.e., they should be used to prevent or reduce disputes rather than, after the fact, to champion their clients' causes. a. Mr. Rubin is a partner in the New York law firm of Postner & Rubin. He has litigated and arbitrated numerous complex construction disputes. He has also participated in efforts to improve contracting practices on committees of ASCE and the National Academy of Engineering. b. Ms. Banick holds a BS in Civil Engineering from the University of Virginia and is a law student at New York Law School. She is a law clerk at Postner & Rubin.

Jan 1, 1983

By B. W. Cavender

Innovative mining and metallurgical operating techniques and processes can be identified and developed by analyzing changes as they occurs within the mine, plant, technology or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions and the development of new knowledge. Innovation can be organized, practiced and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically designed policies regarding organizational structure and staffing, daily management practices and compensation and incentives.

Jan 1, 1996

By Peter M. Fozzard

A review is made of the actual costs of recent foreign mineral exploration programmes in third world countries. Target identification leading to the selection of areas, or macro-targets, must follow a well planned and defined series of steps. Suggestions are made with respect to this inter-active project development work. Potential revenues in the broad sense will always determine the overall economics of exploration but clear objective philosophy, good planning and adequate financing are essential for exploration success. Considerable opportunities exist for making important foreign mineral discoveries and broad selected suggestions are made for the identification of exploration areas in relation to high-grade and precious metal mineralization.

Jan 1, 1984

By G. J. Hodges

The Stillwater Mining Company, a partnership of Pittsburg & Midway Coal Mining Co. and Manville Corporation, operates a precious metals smelter at Columbus, Montana to further up-grade concentrates from its platinum/palladium mine. The smelter began operation in the summer of 1990. The gas cleaning system in the facility utilizes "oxidation/dilute mode" dual-alkali scrubbing technology to capture sulfur oxide gases from the process gas streams. This paper describes the rationale for selecting the dilute mode dual-alkali system and summarizes design parameters. Start-up problems and their solutions are also discussed.

Jan 1, 1992

By K. H. Bettles

The Goldstrike Mine is in Eureka County, Nevada, approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend of sediment hosted, disseminated gold deposits. The Carlin trend comprises over 15 major gold deposits with production, reserves and geological resources of approximately 50 million ounces of gold (Fig. 1). In the Bluestar/Goldstrike subdistrict, there are four major deposits; Post, Betze, Bluestar, and Genesis, plus numerous smaller deposits (Fig. 2). Betze is located on property controlled by Barrick Goldstrike Mines; Bluestar and Genesis on Newmont Gold property; and Post on both Barrick and Newmont property.

Jan 1, 1989

By D. C. Shumway

Recently, the health of the cement industry has been threatened by the impact of environmental regulations, over-zealous state and federal agencies and radical environmental groups. Unfortunately, cement plant operations tend to trigger every environmental regulation and program promulgated, plus several programs designed specifically for the cement industry. These environmental burdens come at a time when the cement marketplace has been impacted by imports resulting in a situation where it has been difficult to increase prices to offset these increased environmental liabilities. The competitive world market forces the cement industry to seek creative ways to reduce costs. With additional major environmental programs coming down the pipe, like the Federal Clean Air Act Amendments of 1980 and EPA regulation of cement kiln dust, the cement industry has attempted to try innovative supplements to cement manufacturing. The cement industry has found that using waste tires, biosolids and other solid wastes in the cement manufacturing process can reduce costs and plant emissions.

Jan 1, 1996

By C. C. Stewart

Jim Walter Resources, Inc. operates four underground coal mines in Alabama. In 1986, during longwall recovery operations, sparks from a torch ignited methane that migrated onto the face after a roof fall. The fire quickly spread to the gob at the tailgate end of the longwall. The fire was successfully "area" sealed and mining operations resumed after five weeks. However, several problems were encountered during this process. This paper describes the events following the fire, methods used to control the situation, problems encountered, and steps taken to ensure preparedness for any future occurrences of this type.

Jan 1, 1993

By George Hufford

An investigation is made into the applicability of queueing theory to simulating the operation of a large open pit copper mine in the southwestern United States. Actual data from a working mine was used to construct curves for truck loading time, haulage and return time, and dumping times. Known results of investigations of queueing models (Koenigsberg - 1958, Gordon and Newell - 1967, Cabera and Maher - 1973) were used to simulate the actual operation. These did not give acceptable results so commonly used probability distributions were fitted to the actual data. A large computer program known as Q-GERT was used with the various parameters obtained from fitting the curves. Kolmogorov- Smirnov tests were run that showed that this was not satisfactory either. Finally, Q-GERT was used with the actual data from the mine. An appropriate correction factor is then found to apply to the exponential probability distributions tested previously and satisfactory results are obtained.

Jan 1, 1981

By Poltak Sinaga

PT Kaltim Prima Coal's 13.1 km overland conveyor was commissioned in 1991. It is of conventional 3 roller 350 troughed belt type. Cost and performance optimisation during initial design ended up with 5.4m/s belt speed, 1,000mm belt width to convey 1,350tph, and 7mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1,100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30mtpa. Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4200tph satisfactorily.

Jan 1, 2008