Search Documents

By Avula Rajashekar Yadav, Sreenivasa Rao Islavath

Barrier pillars and gateroads play a vital role for the safe exploitation of coal from the panel in the longwall workings. The barrier pillars and gateroads are subjected to the front abutment and side abutment loads during the retreat of the panel. These structures may fail if the developed load on them is higher than their strength. The stability of the longwall structures such as barrier, gateroads and face is paramount in extracting the coal from the panel safely. For this, a deep longwall mine in India is chosen for the study using a 3D numerical modelling technique. In this paper, three critical conditions such as scenario 1 (no side goaved-out panel), scenario 2 (with side goaved-out panel) and scenario 3 (with two side goaved-out panels) are taken. For each scenario, five retreat distances such as 100, 125, 150, 175 and 200 m are considered for detailed investigation. The development of vertical displacement in gateroads, vertical stresses on barriers, vertical stress concentration factor, abutment zone and yield zone for longwall face are extracted and analyzed. Also, the safety factor of the barrier and longwall face is estimated considering the Hoek–Brown rock mass failure criterion. From the study, it is observed that the maximum vertical displacement of 121 mm in TG3 at scenario 3 for a retreat distance of 200 m and a minimum vertical displacement of 33 mm in TG2 for a retreat distance of 100 m at scenario 2. The development of vertical stress on the barrier is found to be between 8.78 and 13.40 MPa, and the safety factor of the barrier lies in between 1.56 and 1.80. The study also revealed that the yield zone at the longwall face lies within 2 to 3 m.

Dec 29, 2023

By X. X. Shao

Dewatering of ultra-fine clean coal slurry to a low moisture level of20 percent is difficult using the conventional techniques. A novel approach, which utilized mixing of fibrous waste material, such as paper, carpet and wood, with coal slurry prior to dewatering was developed. It was found that addition of about 10 Kg/t of carpet fibers or 5 Kg/t of raw paper pulp lowered the filter cake moisture from 22.5 to 18 percent. The compressive strength of the filter cake improved from 0 to 4.5 Kglcm2 and impact resistance from 0 to 4. The experimental data indicated that the handling character of the dewatered fine coal was improved significantly.

Jan 1, 1998

By Y. J. Wang

Stall or aerodynamic stall of axial-flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple-fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple-fan ventilation networks, design of the experimental setup for two-and three-fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1991

By Paul Mitchell, Amy Wheaton, James Rybock

Acid rock drainage (ARD) represents one of the most intractable problems faced by the non-ferrous metal and coal mining sectors, and the creation in the recent past of a number of high-level national and international initiatives reflects the growing concerns of industry, government and other stakeholder groups. ARD is certainly considered one of the most serious environmental impacts caused by mining and the industry's greatest environment-related technical challenge. Additionally, the global depletion of non-acid generating oxide ore deposits and the increasing dominance of sulphide ores means that the potential for ARD incidents will continue to increase. Once initiated, the cycle of chemically and biologically mediated and catalysed reactions leading to ARD generation is difficult to stop. While there is evidence to suggest that the degree of contamination of ARD will decrease rapidly within a relatively short timeframe (Wood et al., 1999), experience in historic mining regions of the world indicates that the problem may persist for centuries at certain sites. Current best practice in dealing with ARD puts the emphasis on prediction and prevention, planned from the outset of the operation and integrated with each phase of the mine site life cycle. The elements that constitute best practice are becoming more clearly defined and as this process of clarification continues industry will undoubtedly accelerate the process of best practice implementation, burying at last the image of mining as a despoiler and polluter of landscapes, an image based on past, rather than current, practices. However, it is equally clear that despite the best efforts of industry and regulators, many sites will continue to generate ARD during operation and following closure - in many cases, a legacy of ARD has been derived from operational and strategic decisions made decades ago, before the risks and impacts of the self-sustaining cycle of ARD generation were properly understood. Add to this ARD generation from poorly managed operations and from historic and abandoned sites, and it becomes clear that the treatment of ARD will be required for the foreseeable future to protect water quality, and ecosystem and human health.

Jan 1, 1999

By Gh. Crutu

During exploration and exploitation of complex ores, waste dumps that contaminate severely the environment and in particular soils and waters, are genetated. The most hazardous pollutants are heavy metals and metalloids (e.g As, Mo, Pb and Cu) as well as radionuclides (e.g U and Ra).

Jan 1, 2008

By B. F. Westfall

Throughout the 1960's and 1970's world trade grew rapidly, reaching a peak of USS1.8 trillion in 1980. Since then the world recession of the early 1980's shrunk trade to about US$1.6 trillion. The reduced cash flow to developing economies made it difficult to service their huge international debts, Nowadays lenders are reluctant to grant Third World countries additional credit. The shortage of export financing, plus trade barriers set up by developed countries, is further inhibiting international trade. Therefore, countries are turning to new and creative alternatives to financing imports of consumer as well as of investment goods. Non-cash transactions, including different forms of countertrade, are rapidly growing alternatives to traditional trade financing patterns. In 1983 about 30% of international trade, or close to US$600 bill ion, were presumably done by non-cash transactions, up from barely 2% in 1976. By year 2000, half the world trade is likely to be conducted on basis of barter. As of mid-1984 some 88 nations used countertrade regularly and Governments of at least 15 Latin American countries had arranged or mandated commercial countertrade.

Jan 1, 1986

By Robert C. Ellman

Lignite and subbituminous coals are utilized essentially as mined without beneficiation. Most of the present production is used to generate electric power and the major problem in this use is ash deposition on fireside surfaces. The preparation at existing mines involves principally crushing and screening operations. Blending of production from different locations within the mine is practiced in several mines to control ash composition. Drying and oil treatment for freezeproofing, of lignite are used to a limited extent during winter. Future processing may involve both washing and drying operations to alter ash composition by ion exchange and upgrade the low-rank fuels to higher heating values. Research has been initiated to determine the feasibility of such processing.

Jan 1, 1969

By Nagashi Ogushi

Geochemical prospecting method using stream sediments, soils and rock chips has been tested to see the applicability for the typical Kuroko field in Japan. Three independent anomalies have been detected in maps being shown by grav densities of cells which are represented by the results of factor analysis as well as distribution of minor elements scaled in logarithm. A small vein type mineralization which has outcrops could be attributed to the origin of them whereas the one near the surface of known Kuroko deposit to a coincidence. The addition of drill core geochemistry is required to complete the interpretation.

Jan 1, 1982

By W. R. Reed, J. P. Rider

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a medium-sized surface blasthole drill shroud with a dry dust collector system. CFD models were constructed in ANSYS FLUENT Version 15. Previously run experiments conducted in the NIOSH full-scale drill shroud laboratory were utilized to validate the models. The setup values in CFD models were calculated using experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for test scenarios, including 0.14 m3/s (300 cfm) bailing airflow with 2:1, 3:1, and 4:1 dust collector-to-bailing airflow ratios and 0.24 m3/s (500 cfm) bailing airflow cases with 2:1, 3:1 and 4:1 dust collector-to-bailing airflow ratios. For the 2:1 and 3:1 ratios, results showed the calculated dust concentrations from the CFD models were within the 95% confidence intervals of the lab experimental dust concentrations. This paper describes the methodology used to develop the CFD models, to calculate the model dust input, and to validate the models based on experimental data. Problem regions were identified and revealed by the simulation of a dry dust collector system. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. INTRODUCTION In surface mines, production drilling is an essential process in blasting which fractures the hard rock overburden for removal. Holes with a predetermined pattern, diameter, and depth are drilled into the overburden to introduce explosives. During the drilling process, considerable amounts of respirable dust are produced. Past research conducting area sampling at blasthole drills has documented time-weighted average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 [1] and 1.04 to 52.30 mg/m3 [2]. These high dust concentrations, which may contain silica, can lead to respirable dust over-exposures for the drill operator, drill helper, and other personnel in the vicinity. These over-exposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal. In order to prevent the development of silicosis to mine workers, the Mine Safety and Health Administration (MSHA) regulates the exposure to respirable dust. For metal/nonmetal (M/NM) mines, MSHA has adopted the threshold limit values recommended in 1973 by the American Conference of Governmental Industrial Hygienists (ACGIH) [3]. The total airborne dust standard is 10 mg/m3. However, if the sample contains greater than 1 percent quartz (the most common form of crystalline silica), a respirable dust standard is calculated with the following equation: Respirable dust standard = (10 mg/m3) / (% respirable quartz + 2)"

Jan 1, 2016

By d&apos, L. F. G. Assumpcao

Kaolin samples from Rio Capim resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the color removal process. Coating clays and delaminated clay were tested. Retention time (or pulp injection velocity), magnetic field intensity and matrix type were the' variables studied. The feed brightness ranged from 84.7 to 87.6 % ISO for the coating clays and from 80.7 to 85.4 % ISO for the delaminated clay. The results showed unleached brightness values higher than 88 % ISO for coating products and higher than 87 % ISO for the delaminated product, using a conventional magnetic separator with an applied field of 1.5 to 2.0 Tesla. With a maximum field intensity in the superconducting machine of 5.0 Tesla, unleached brightness values higher than 88.5 % ISO for both coating and delaminated clays were attained.

Jan 1, 1995

By R. Bruce Tippin

because of the mineral's high monetary value and the spotty occurrence of free gold in the deposit. Setting up a plant sampling procedure by simply applying the usual statistical sampling theory was questionable. Two sampling concepts were considered in the sampling study: o a sufficient number of assays can be taken such that the average determined from these individual samples represents a known quantity of ore. o a sufficient weight of sample can be taken such that when assayed it represents a known quantity of ore. The test program included evaluation of sampling techniques, sample preparation and analytical methods. The overall sampling program is depicted in Figure 2.

Jan 1, 1985

By C. I. Basilio

Pearson's hard and soft acid and base (HSAB) principle may be applied to flotation systems. The HSAB principle states that hard acids prefer to bond with hard bases and soft acids prefer to bond with soft bases. By determining the Drago E and C parameters for the different components of a flotation system, the HSAB principle could be used to explain the selectivity of some collectors such as thionocarbamates against some minerals. Determination of these parameters is done by utilizing Drago's theory and flow micro-calorimetry.

Jan 1, 1991

By Romeo S. Jurani

Bulkspray cooling has been economically applied in cooling the hot environment of South African gold mines for the past two decades. Its success in that country led to its introduction at Gulf Mineral Resources Co.'s Mt. Taylor Mine in 1981 when increased drifting imposed additional cooling requirements. The bulkspray cooler developed and used at Mt. Taylor has a heat transfer capability of about 500 to 1500 kW. It is compact and portable, designed to be moved as required to maintain working temperatures in the advancing drift faces.

Jan 1, 1983

By Immo H. Redeker

This is a final progress report on a cooperative project conducted by three private feldspar companies,** North Carolina State University, and the federal Bureau of Mines. The object of the project was to reduce the feldspar tailings disposal problems at the flotation plants in the Spruce Pine area of North Carolina. The initial phase of the project revealed that high tonnages of saleable feldspar and quartz were lost in the tailings and the three feldspar companies are now concentrating their efforts on feldspar recovery, either by reclamation from the tailings as suggested by the Asheville Minerals Research Laboratory or by improvements in metallurgy in the existing plants.

Jan 1, 1970

By Fitzhugh T. Lee

Results from the first part of a two-part investigation of the stability of highwalls in open-pit coal mines in the Paleocene Fort Union Formation of the western Powder River Basin of Wyoming and Montana indicate that these highwalls are subject to time-dependent deformation. Field investigations and laboratory physical properties tests of coal and overburden rocks suggest that several factors influence highwall stability. Some of these factors are rebound of overconsolidated rocks, desiccation, water, orientation and spacing of fractures, and strength and deformation properties. Factors of safety for a typical highwall in the study area (calculated by the finite element method) may be less than 1.0 when open fractures are present and the highwall has degraded. Although it is concluded that most open-pit highwalls in the Fort Union Formation within the study area have adequate short-term stability, these highwalls do deteriorate and become progressively less stable. Because of this, postmining failures are common and stability conditions could become critical if mining were delayed and then resumed after a period of several months. The second part of the investigation will utilize field measurements of rock-mass properties and instrumentation of actively mined highwalls to obtain data for comparison with the results of the initial investigation. Because the height of highwalls will increase as the more shallow coal is exhausted, these data will also be used to predict the behavior of slopes higher than those presently found in the western Powder River Basin.

Jan 1, 1977

By K. N. Santini

Natural zeolites are gaining recognition as an important commodity with an increasing number of industrial and consumer applications. This potential has prompted the Anaconda Minerals Company and other firms to investigate occurrences and markets for zeolites. The deposits of mordenite-rich tuff at Rome are of interest for their economic potential and for the excellent opportunity they provide to study a zeolite deposit formed in a hydrologically closed basin. Location The Rome property is located approximately 9 km west of Rome, Oregon, in Townships 31S. and 32S., Range 41E., Malheur County. It lies within the Owyhee Uplands of the northern Basin and Range physiographic province (Figure 1). The area discussed here includes a major portion of the depositional basin in which the zeolitic tuffs occur.

Jan 1, 1982

By S. D. Bearden

China was the world’s leading producer of barite during 1995 with 35%. The United States followed with14%. India produced 9%. Other producers included Morocco, Turkey, Mexico and Germany. Domestic production of barite during 1995 was estimated to be 600 kt (660,000 st). Nevada produced 85% of the total. Georgia was the second leading barite-producing state. The United States is the world’s largest consumer of barite. During 1995, it used 1.6 Mt (1.8 million st). US reliance on imported barite during 1995 was about 63%of total consumption, according to the US Geological Survey.

Jan 1, 1996

By M. De Ladurantaye-Noël, M. Laliberte

Selenium is widely present in the environment at usually low concentration. It is mostly present in the environment at higher oxidation states, i.e., as selenites and selenates (+4 and +6 oxidation states respectively). It is rarely present as selenides (-2 oxidation state) and almost never found as the element (0 oxidation state). Selenites and selenates are generally soluble in water, as such they cannot easily be removed from water by precipitation. Selenites can form insoluble surface complexes with metal oxides such as ferric hydrous oxide and manganese hydroxide, and can therefore be removed that way. However, it is not so common to find selenites in natural environments as it will quickly oxidize to selenate in aerobic conditions. Elemental selenium can also be produced from selenites or selenates by using a reduction process; the end product is a colloid that can be destabilized to be removed from water using the right chemistry. Because of their toxicity, selenides need to be handled with care, and if present, it can form insoluble metal salts or, at low pH, be emitted as H2Se, a noxious and highly toxic gas. The most favorable selenium forms for its removal are therefore selenite and elemental selenium. Organo-selenium species play a crucial part in understanding selenium toxicity. There are a great number of these species. Basically, any organic species that contains sulfur has an equivalent that contains selenium. Of particular interest is the substitution of sulfur by selenium in the two sulfur-bearing amino acids, cysteine and methionine, resulting in selenocysteine and selenomethionine. Methylseleninic acid (CH3SeO2H) is another organo-selenium specie which has been detected in water treated by biological processes and which is biologically active.

Feb 1, 2023

By Jay P. Chapman

The basic control requirement for multi-pump, long distance slurry pipelines are discussed and a particular example of an operating slurry pipeline using programmable controllers is presented.

Jan 1, 1983

By Walenty Frydel

The paper deals with highly efficient dust collecting systems of the 10-600 type which constitute new generation installations de- signed to eliminate dust hazard in headings driven with roadheaders. A vortex ventube controlling the air flow in the com- bined ventilation system by means of air vortex generated by the ventube drive unit is also presented. From the results of measurements of under-roof concentrations of methane it appears that the application of the vortex ventube makes it possible to decrease the under-roof accumulation of methane more than 10 times.

Jan 1, 1997