Search Documents

By P. Maraboutis

Extractive industry (mining and quarrying operations), as other industrial activities, is subject to environment protection laws, regulation and standards such as the Environmental Impact Assessment directive, Natura 2000, Habitats & Birds directive, Water Framework directive etc The European Commission (EC) is aim to strengthen the EU environmental legislation to improve the (environmental and human) safety of mining activities. The mineral processing and the management of the mining waste will be covered by the new amendment of the Seveso II Directive, by a Best Available Techniques reference document (BREF) describing the Best Available Techniques of mining waste management and a new directive on the mining waste management. At the same time initiatives as the environmental liability, the energy taxation for environmental reasons and the natural resources management policy, which will have a positive impact on the protection of the environment, will affect the extractive industry operation procedures.

Jan 1, 2002

By J. A. Mielczarski

An infrared external reflection spectroscopy (ERS) technique has been developed to study the structure of the adsorbed layer of ethyl xanthate formed on copper and natural chalcocite (Cu2S) electrodes. The infrared technique provides information concerning the identity and the orientation of the adsorbed species at monolayer and submonolayer coverages. X-ray photoelectron spectroscopy (XPS) studies have also been conducted to monitor changes at the surface. The results show that the first oxidation peak on the voltammograms for copper and the first and second oxidation peaks on the voltammograms for chalcocite electrodes are not characteristic of a chemisorbed xanthate species, which is contrary to what has been reported by other investigators previously. As evidenced by the XPS spectra, there was an increase in sulfur relative to copper on the copper and chalcocite surfaces over the potential region where these oxidation processes occur. The spectroscopic results (ERS, XPS) indicate that the second and third (on copper) and the third and fourth (on chalcocite) oxidation processes recorded on the voltammograms are due to cuprous ethyl xanthate adsorption. The orientation of the adsorbed molecules of xanthate was observed to change with increasing surface coverage. Therefore, it has been concluded that xanthate can modify the copper and chalcocite surface in two different ways. At lower potentials, xanthate is a source of sulfur for the formation of a sulfur-rich surface. At higher potentials, an adsorption layer of cuprous ethyl xanthate is formed. Contact angle measurements show that both of these processes of xanthate surface modification lead to an increase in the hydrophobicity of the substrates.

Jan 1, 1990

By Muriel S. Robinette

Ground-water contamination from uranium operations could be avoided with proper site analysis techniques. Contamination from tailings disposal sites is carried downgradient within permeable hydrostratigraphic units which can be located and delineated with a combination of drill holes, borehole geophysical logs and surface geophysics. Several case studies are presented to illustrate this application.

Jan 1, 1980

By Jr. Mason

Eminent Domain is the power of the government or municipality to take property for public use without the consent or acceptance of the owner. Typically the agency taking the property will make an offer on the property, hoping that the owner will immediately accept and allow work to begin. If a mutual resolution regarding the property value cannot be reached, however, the municipality will condemn the premises and institute a condemnation action in a court of law, which is when the problems begin. The power of the government to take the subject property is limited by the Federal and State constitutional duty to pay "just compensation" for the property.

Jan 1, 1989

By C. Manea

During exploration and exploitation of complex ores, waste dumps that contaminate severely the environment and in particular soils, are genetated. The most hazardous pollutants are heavy metals and metalloids (e.g As, Mo, Pb and Cu) as well as radionuclides (e.g U and Ra). Ecological remediation aims, among others, at decontamination of soils by preserving important properties as soil fertility.

Jan 1, 2008

By İlknur Erol

The abstract highlights that hearing loss is an occupational disease caused by noise exposure in the workplace. The study investigates noise-induced hearing loss among miners in underground coal mines in Turkey, considering factors like occupation, age, and exposure time. The research employs logistic regression analysis to reveal the relationship between hearing loss and these factors. The findings suggest that occupational groups and duration of noise exposure significantly affect hearing loss. Miners in production groups and those exposed to noise for 10-14 years have a higher risk. The study concludes that age does not significantly increase the probability of hearing loss.

Mar 24, 2022

By G. Deschenes, P. J. H. Prud'homme

A laboratory study was carried out to evaluate the effect of oxygen and lead nitrate on the recovery of gold by cyanidation of a free milling gold ore, which contains 0.4 % copper as chalcopyrite. Efficient gold extraction is achieved only under specific conditions. The recovery of gold was increased from less than 90% to up to 98% by addition of lead nitrate. In the pre-leaching, the kinetics of oxidation of soluble sulphides are not an accurate indication for the length of the treatment. Even though the consumption of cyanide was reduced due to the inhibition of the dissolution of chalcopyrite by increasing additions of lead nitrate, cyanide consumption had to the held above 1.85 kg/t to maintain good recovery of gold. The continued addition of lead nitrate above 300 git had no impact on the recovery of gold. It was also found that the addition of lead nitrate at the start of cyanidation gave the same performance as when added during pre-leaching. The addition of oxygen increased the recovery of gold by 1.5%. The concentration ofNaCN had to be maintained in the range of700 mg/L because of the high concentration of copper in solution. The recovery of gold dropped significantly when the average NaCN concentration fell below 640 mg/L. Application of the findings of the laboratory study at the industrial scale led to improved plant performance.

Jan 1, 1997

By J. Kalliokoski

As part of a funded project we have completed a comparative literature survey of the US regional Proterozoic geology. For our com¬parative study model we used the geological settings of the very large pitchblende deposits in Saskatchewan, Canada and the Northern Terri¬tory of Australia. These occur in a variety of Archean and Lower Proterozoic host rocks, at and below a regional unconformity that is capped by subhorizontal Middle to Upper Proterozoic conti¬nental sedimentary rocks. We find that there have been recorded in some parts of the US similar unconformable sequences of Middle to Upper Proterozoic continental sedimentary rocks that overlie older basement rocks.

Jan 1, 1979

By Amy McBrayer, Andrea Brickey

Limited research has been conducted related to the development of mathematical optimization models for production scheduling at large surface coal mines using the area, i.e., strip, mining method. Increased economic and technical challenges have led to a new interest in production schedule optimization models for these type of mining operations like those currently applied to model underground and open pit mines. While area mines share similar characteristics to both open pit and underground metal operations, neither an open pit nor underground production scheduling model adequately depicts an area mine mathematically. We present an integer programming model with blending constraints and discuss the challenges and opportunities related to the implementation for area mines as well as future research in area mine production scheduling.

Jun 25, 2023

By A. L. Hinde

Ideally, mill circuits should be controlled so that excessive random disturbances are reduced in frequency and amplitude. It is difficult to derive an objective measure of the effectiveness of any chosen control strategy. Often, the response of the circuit to pulse or sinusoidal disturbances is used as a measure of the effectiveness of control, but this is not adequate in many circumstances because such disturbances bear little resemblance to those that occur in practice, and such an approach cannot be easily related to the profitability of the reduction process. A superior approach appears to be the application of the theory of stochastic processes. This theory permits both real process disturbances to be modelled accurately, and useful objective functions for control to be derived. A test of the usefulness of stochastic theory in mill control was made on the gold ore milling circuit shown in Figure 1. This circuit was fed with an ore which had a liberation characteristic such as that shown in Figure 2. It is simple to show that, for such a liberation characteristic, the recovery of valuable mineral will vary as the standard deviation of the particle mass-size distribution varies even though the mean particle mass-size is kept constant. Similarly it may be shown that excessive perturbations in the circulating load in a milling circuit such as that shown in Figure 1 can affect liberation. Figure 3 shows how, as the cyclone feed density increases and the sump water addition decreases at constant sump level, the cyclone operation becomes unstable and the discharge "ropes? with a consequent catastrophic coarsening in product size. By minimising the variance of the circulating load it is possible to reduce the probability of initiating instabilities of this nature.

Jan 1, 1977

By James D. Hervol, Josepph W. III Leonard, Barbara J. Arnold

INTRODUCTION Dry concentration or pneumatic cleaning uses air currents as the separating medium. Pneumatic cleaning in the United States today is limited to three or four operations. In fact, the quantity of bituminous coal cleaned pneumatically has declined from its peak in 1965 of about 25.4 million tons (23.1 Mt) to its current level (1988) of less than 4 million tons (3.64 Mt) annually, as shown in Fig. 7-9 1. In 1940, pneumatic methods accounted for 15% of the bituminous coal and lignite cleaned in the United States as given in Table 7-32. Currently, pneumatic methods account for less than 2%. The largest air plant was built in Pennsylvania about 1968 with 14 units processing 1400 tph (1280 t/h) of 3/, in. X 0 (19 mm X 0) raw feed and two additional units retreating middlings. This same plant is one of only three or four plants still operating air-cleaning devices in the US. A wet plant was added in 1985 to increase the efficiency of cleaning the fines. The air plant is still used as a scalping operation for the coarse material. Five additional operations are either no longer in production or have discontinued the use of air tables within the last year. Wet cleaning methods are now being employed at the facilities that have discontinued air table operation. he advantage of dry cleaning techniques is the low moisture content of the clean coal product. However, to decrease respirable dust, mining operations must use water sprays on modem mining equipment. This water adds to the moisture content of the run-of-mine coal and decreases the effectiveness of dry cleaning processes that rely on low surface moistures in the feed to allow for good separations. Wet cleaning methods are preferred, especially since they also allow for much sharper separations. The advantage of dry cleaning techniques is the low moisture content of the clean coal product. However, to decrease respirable dust, mining operations must use water sprays on modem mining equipment. This water adds to the moisture content of the run-of-mine coal and decreases the effectiveness of dry cleaning processes that rely on low surface moistures in the feed to allow for good separations. Wet cleaning methods are preferred, especially since they also allow for much sharper separations. Despite dry concentration's drawbacks, research has continued into dry concentrating methods, including both electrostatic and magnetic separation techniques. The real application for future dry cleaning processes is probably at the power plant between the pulverizer and the boiler feed where particles are already dry and ground to fine sizes (- 200 mesh [ -0.075 mm]), increasing the effectiveness of the separation and also, possibly, increasing the liberation of clean coal from finely disseminated impurities. From a utility's viewpoint, pneumatic cleaning offers the best delivered Btu cost, based on the premise that a percent of moisture is just as detrimental as a percent of ash. Additionally, several other advantages are inherent in dry concentration techniques. The main advantage is that dry concentration re-

Jan 1, 1991

By F. G. Crack

This paper is based on the philosophy that the management structure and strategy required for mine construction and development projects are different from that required for routine production and maintenance operations in a mine. The purpose of this paper is to present an integrated approach to the management of mine development projects. This paper highlights the four major aspects of the integrated approach. First, a brief review of the various types of contract documents is provided. Second, the management organization of a project is discussed. Third, the project manager's role and the field supervisor's responsibility are briefly outlined. Finally, the use of scientific techniques for planning, scheduling, executing, and controlling projects is presented. Each of these aspects is important; however, each by itself cannot be expected to bring order or unifying impact to the complexities involved in overall project management. When all these aspects are coordinated, the result will be a sore successful project from conception to completion.

Jan 1, 1982

By R. A. Wharton, Z. Yang, R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al(III) and flotation collectors. It was found that the presence of Al(III) is necessary for good flotation of the organism, whether or not Pb(II) is present, when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8, and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al(III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminopropionic acid is used as collector, good flotation occurs at about pH 4 without the addition of Al(III).

Jan 1, 1992

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite is one of the main players in the stability of drilling mud. Its particle size and particle size distribution significantly affect drilling mud’s rheological properties. Although the Specifications for Drilling Fluids Materials report on Oil Companies Material Association (OCMA)-grade bentonite states that the API recommended powder having 2.5 percent mass fraction as the maximum value of residue of diameter greater than 75 μm, there is no other information on the specific size distribution for API bentonite. It was found that API bentonite has a specific size distribution with specific mixing weights. It is important to investigate why that mixture represents the optimum properties of drilling mud and how each individual size fraction has a specific function in the mixture. To clarify the effect of individual size as well as the collective effect of the size distribution, API bentonite was classified into different size fractions, with each tested separately for controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness and packing density.

By B. Li

"Sepiolite is a magnesium-rich, porous, and fibrous clay mineral with broad applications. These applications take advantage of sepiolite’s high specific surface area and unique nano-sized channel structure. Over the past years, numerous materials and techniques based on the structure and property of sepiolite have been developed. This article reviewed the recent achievements in developments and applications of sepiolite in environmental protection, catalysis area, and nanocomposites. The prospectives of sepiolite applications is also discussed. INTRODUCTION Sepiolite is a magnesium-rich, porous, and fibrous clay mineral. The typical chemical formula of sepiolite is Si12Mg8O30[OH]4[OH2]4·8H2O [1]. Sepiolite has a high specific surface area and nano-sized channels because of its special structure [2]. This unusual crystal structure projected onto the [001] plane is shown in Fig.1 [3]. As it can be seen, silicon and oxygen atoms make up for the tetrahedral structure and magnesium and oxygen atoms form octahedral structure, respectively. Those tetrahedral-octahedral-tetrahedral ribbons expand boundlessly in one direction, leading to the special fibrous structure of the sepiolite. Every tetrahedral-octahedral-tetrahedral ribbon is combined to the next by an inverted Si–O–Si bond, which causes an interlaced layer with a continuous tetrahedral sheet and a discontinuous octahedral sheet. Terminal MgO at the edges of the ribbons is coordinated with two structural water molecules, which can form hydrogen bonds with zeolitic water molecules that are located in the channels running parallel to the fiber axis [3,4]. The Mg2+ ions inside the channels can be exchanged with other cations in solution. Therefore, sepiolite can be used to remove metal cations from aqueous solutions [5,6].It can be seen from Figure. 1 and Table 1 [7], the unique structure endows sepiolite with a substantial surface area and nanoscale channels. Its specific surface area reaches 320 m2/g and channel dimensions up to 3.7×10.6 Å. There are three active adsorption sites on the surface of sepiolite: one is oxygen atoms of the Si-O tetrahedron. The second is the structural water molecules paired with magnesium ions at the edges of the ribbons, which can form hydrogen bond with adsorbent. The last one is the Si-OH groups due to the breaks of the Si-O-Si bonds on the surface of Si-O tetrahedron. Thus, sepiolite has strong adsorption ability which has been widely used in environmental protection. Moreover, sepiolite has many significant features such as good mechanical and thermal stability, rheological property, porous, and easily modification, making it be a hotspot in chemical and biological researches. However, with the development of technology, broader and more advanced applications of sepiolite have been carried out in recent years. In this study, the recent achievement in sepiolite applications is summarized, the further tendency is also discussed."

Jan 1, 2018

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014

By C. H. Perbix

[On Pier D in the Port of Long Beach, California, the Port of Long Beach has built a new bulk cement distribution terminal. The facility is operated by Pacific Coast Cement Corporation, who designed the complex and leased it from the Port of Long Beach on a 40-year lease. At one bulk cement is unloaded from vessels carrying from 12,000 to 30,000 t. The unloading is performed with pig speed mechanical unloading equipment and delivered into a concrete silo complex with, a capacity of 50,000 t. From the silos, bulls cement is loaded into trucks for delivery. The facility was completed in September 1981.]

Jan 1, 1983

By Z. T. Bieniawski

The efficient and safe design of room-and-pillar coal mines still remains as one of the pressing problems facing the mining industry in the United States. Although much research has been directed to stability of mine roofs and coal pillars, no generally-accepted design method has been formulated. This paper presents a concise procedure for an improved design of room-and-pillar coal mines. Developed as a result of a three-year research effort, the methodology includes essentially three aspects: (i) determination of stable roof spans; (ii) determination of the strength of coal pillars; and (iii) determination of safety factors for room-and pillar coal mining in the United States. It is shown that the presented approach will lead to a greater recovery of coal by a more economical, yet safe, mining operation. Design charts and tables are presented and a step-by-step design procedure for practical mining engineers is explained. Several examples are included demonstrating the use of the proposed design procedure for room-and-pillar coal mines.

Jan 1, 1983

By Thomas R. Mills

Under contract to the U. S. -Department of.-Interior, Office of Coal. Research, Hittman Associates recently completed a 16 month study of the environmental-factors associated with the siting, construction, and operation of large scale coal refineries. (1 2) The objective of this study was to identify the environmental effects and to define the magnitude of these effects and the approaches which can be used to mitigate adverse environmental consequences. In the study, the five major coal bearing regions of the country having reserves adequate to support a number of large scale coal refineries were considered. The regions considered were: Appalachian, Eastern Interior, Fort Union, Powder River, and Four Corners.

Jan 1, 1975

By A. W. Khair

This paper presents a strength formula for the design of coal pillars. The formula is derived from results of laboratory experiments, studying the effects of primary factors influencing the strength of the coal specimens/pillars. Five primary factors, significantly affecting the strength characteristics of the coal specimens/pillars were identified and extensive laboratory investigations were carried out. The five primary factors were namely 1) coefficient of friction between loading platens and coal specimens, 2) elastic properties of the loading platens, 3) coal specimen geometry, 4) coal specimen size, and 5) rate of loading. Four to nine levels of variation for each primary factor on the strength of coal were studied. An empirical formula, implementing the variation of the primary factors affecting the strength of coal specimens/pillars, has been developed. A comparative analysis of the results provided by this and some well known formulae is also presented.

Jan 1, 1994