Search Documents

By Remo Grandori

The Umiray Angat 13,2 km long tunnel in Philippines have been bored through extremely variable and difficult ground conditions including a number of special events. In particular the following adverse conditions were found: faults in decomposed ground, high temperature rocks, extremely rapid and important convergence phenomena, water inflows up to 800 litres per second. The special El Nino climatic conditions caused a long dry season and lower the level of the lake that was granting the access by barge to the site under the minimum navigable level. Many equipment have had therefore to be transported to site by a 10 ton capacity helicopter, after having been partially dismounted. For the same reason most of the tunnel drive have been bored servicing the site by 1 ton capacity helicopters to transport materials, spares and personnel. In order to overcome the above geological and logistic problems several innovation were introduced and tested in this project. Despite all that difficulties the 13,2 km of tunnel were bored in about 24 months, with a global average of 500 m/month.

Jan 1, 2001

The more than 40,000 mining industry professionals that are expected to attend the National Mining Association’s(NMA) MINExpo International2000 trade show and conference will be treated to the exhibition’s largest display ever. The exhibit is expected to cover more than 60,385 m2(650,000 sq ft) and feature more than 1,300 exhibitors. The event is set for Oct. 9-12, 2000 at the Las Vegas Convention Center in Las Vegas, NV. Richard L. Lawson, NMA’s president and chief executive officer, said, “MINExpo 2000 will showcase everything that mining is proudest of. This is the largest premier mining exposition in the world.” MINExpo is held every four years.

Jan 1, 2000

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

Jan 1, 2006

By Steve Kral

The mining industry in Colorado faces the same problems the industry faces throughout the United States and the world — record low commodity prices and increasing regulatory and environmental restrictions that seemed designed to curtail mining activities. Despite those obstacles, the mining industry in Colorado still contributes about $8 billion annually to the state’s economy in the form of base and precious metals, industrial minerals, coal and associated service businesses and jobs. So the 300 attendees at the102nd National Western Mining Conference felt reason-ably positive about the industry in their state. The meeting is the Colorado Mining Association’s annual conference and was held at the Broadmoor Hotel in Colorado Springs in November. The theme was “Mining in the New Millennium — Achievement + Innovation = Survival.” Experts from Colorado’s mining industry and abroad discussed the challenges faced by the mining industry as it enters the new millennium. They offered insights into how the industry will operate during the early years of the 21st century and how it will survive low prices and increased regulatory restrictions.

Jan 1, 2000

By A. H. Shapiro

A decanter centrifuge of novel design was developed for the dewatering of fine-solids slurries having micron-range particles that form paste-like, flowable, hard-to-dewater cakes. The design combines a compound beach with a cake-flow control structure that allows expressed liquid from the cake in the dry beach region to be returned back to the liquid pool while maintaining high solids throughput. In order to provide optimal performance with various operating parameters (feed rate, centrifugal gravity, pool, differential speed, concentration of feed solids, and different slurry types), the cake-flow control is adjustable. The second part of the beach is preferably at zero angle. Tests showed that the new design allows increases in both solids dryness and solids throughput.

Jan 1, 2001

By Henry A. Signore

The Appalachian coalfield, located in eastern Kentucky, Pennsylvania, Virginia and West Virginia, has been one of the most productive in the United States. Total production from the Appalachian coalfield during 1994 was 340.8 Mt (375.4 million st), or 37% of the 929 Mt (1 billion st) produced in the United States that year. This region contains various coal types from high- to mid-sulfur coal in Pennsylvania and northern West Virginia to low-sulfur, compliance steam coal and premium-grade metallurgical coal in eastern Kentucky, Virginia and southern West Virginia. The region's product is in high demand in domestic and export markets. Productivity continues to improve, resulting in the primary coal operators solidifying their market positions.

Jan 1, 1995

By Nathaniel Arbiter

In contrast to pyrometallurgy's 6000year history in metals production, hydrometallurgy is of relatively recent origin. The earliest reference to it was in the 16th century, with the first applications to copper in the 17th and 18th centuries. In the 19th century, increased demands for pure metal resulted in the development of electrolytic refining, and early in this century electrowinning. The rapid growth in copper production in the 20th century, particularly in the United States and Chile, stimulated the development of new technology for leaching and for the recovery of copper from leach solutions. In the past 25 years, solvent extraction has become a major factor by permitting novel leaching technology that produces dilute or complex solutions. In addition, solvents other than sulfuric acid, and chemical methods for precipitating copper metal are now of increasing interest. These are trends that should grow in importance with the need to process lower grade and more complex materials. The evolution of copper hydrometallurgy is reviewed. Key factors in recent major developments are presented with details of specific operations and with trends for the future indicated. The relative importance of copper hydrometallurgy is compared with that of pyrometallurgy in the light of probable changes in ore supplies and character.

Jan 1, 1994

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007

By J. Jonas, J. M. Harrington, K. Wangerud, S. D. Fundingsland, J. G. Harrington

EPA NRMRL Mine Waste Technology Program and Region VIII Superfund office are jointly conducting an in-situ technology demonstration at the Anchor Hill Pit Lake, Gilt Edge Mine Superfund site. The goal is to develop in-situ treatment cost/performance data for potential application in long-term water treatment/management at Gilt Edge and similar sites. The pit contained 77,000,000 gallons of pH 3water with elevated metals, sulfate, and nitrate. The Green World Science® patented process for in situ treatment was implemented to isolate and sequester metals; create stable long-term water quality and restore a sustainable ecosystem. COCs have decreased more than 99%, and dissolved discharge standards were attained.

Jan 1, 2004

Overcasts are indispensible ventilation control devices to permit one airway to pass over another without mixing in room and pillar coal mining. The airflow distribution inside the overcast depends on its spe-cific configuration at which the flow enters into it. This study uses 3D numerical simulation to examine the pressure and velocity distributions inside an overcast. The effects of the overcast angle on the flow field are also examined. The flow is assumed to be turbulent and isothermal and the standard k-e model is utilized. Simulated results display flow separation and recirculation regions of different sizes occurring not only upstream and downstream from the overcast but also inside it. The results also show that the size of the recirculation regions in-creased with the increase in the angle before and after the overcast influencing significantly the flow field and pressure losses. The stream-lines are plotted to show the 3D structure of the flow field. The results from the simulation can guide overcast design commonly used in un-derground coal mines. Keywords: 3-D simulation, Overcast, Room and Pillar, Turbulence, Recirculation Region

Feb 27, 2013

By William Reininger

Microtunneling provides a necessary solution for multiple utility crossings associated with the New York Metropolitan Transportation Authority Capital Construction Company?s (MTACC) Eastside Access Project for the Long Island Rail Road. Construction of four TBM tunnels and their approach structures at the eastern end of the project in Sunnyside, Queens required significant modification and expansion of the railroad infrastructure at this location. Maintenance of railroad traffic during project construction is a principal requirement. As a consequence fourteen (14) utility crossing segments are being installed under active traffic by microtunneling methods. Microtunnels were installed in a variety of conditions including depths, types of soils and construction restraints.

By Leon Maday, Dan L. Pecha, Jeremy Johnson, Daniel N. Adams

The Brightwater conveyance system includes 26 km of tunnels, a 130 mgd pump station, 2 km of micro tunnels, and a 2.4 km outfall. The tunnels extend from Woodinville to Puget Sound through varying soils in 1 to 7 bars of hydrostatic pressure and depths to 185 m. The tunnel diameters range from 4 to 6 m and include numerous lining systems. This paper highlights major shaft and tunnel design, including dual cellshafts, multiple pipe configuration tunnels, polymer concrete segments, and the use of a one pass lining designed to convey high pressure effluent.

Jan 1, 2005

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide)are situated in Arkansas. Less concentrated brines(about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in those two states. Its value was $191 million. In 2004, the estimated U.S. bromine production was 222 kt (244,000 st). That compared with 216 kt (238,000st) produced in 2003.

Jan 1, 2005

By L. Lacerda

Spray-on ground support membranes (GSM) or thin support liners hold today perhaps as much potential to impact underground (u/g) ground support operations as dry and later wet-mix shotcrete when introduced to mining in the latter part of the 20th century. This emerging technology has come a long way from the time the first single component experimental coatings were tested in the mid-1980s. Due to a number of factors, including occupational health risk and mine safety regulations, it has taken quite some time for the development of non-hazardous membrane products. However, at this junction most existing u/g mines that employ more conventional forms of ground support could benefit from evaluating GSM technology as a means of improving safety and the bottom line. The same is especially true for future mine developments. This paper describes Master Builders Inc.’s CS1251 GSM product and its implementation. It discusses the situations in which GSM may replace other forms of ground support. Furthermore, it evaluates GSM costs & safety issues and looks at present applications and the potentially bright future of this technology.

Jan 1, 2002

By H. H. Murray

Recently developed clay deposits that will impact regional and world markets are described. These deposits, their location, geology, and physical properties are delineated. Kaolins from the State of Para in Brazil and from Ukraine; bentonites from Argentina and India; and palygorskite and sepiolite from China are world class deposits that when processed using modem technology will produce excellent products. Other deposits that may affect regional markets are kaolins from China, Australia and Indonesia; bentonites from Georgia (formerly USSR) and China; and palygorskite from India and Ukraine. New ball clay deposits that will affect regional markets are in China and Indonesia.

Jan 1, 1999

By Laura McNally

In 2006 McNally International Inc. in a Joint Venture partnership with Aecon Constructors was the successful bidder on two York Region Tunnel Projects: Bathurst Collector/Langstaff Trunk Sewers; and YDSS Interceptor Sewer 19th Avenue Project. These projects comprise a total of 13 kilometres of 2.74 meter finished diameter tunnels and are both part of the York Durham Sewer System (YDSS). Both contracts require the use of EPB tunnel boring machines with a precast concrete segmental liner. The following provides an overview the two projects.

Jan 1, 2008

By D. Rahal

All ores have an economic optimum particle size (Wills and Napier-Munn, 2006). This optimum value is often a compromise between the need to achieve adequate liberation for the efficient separation and recovery of valuable minerals and the energy consumed by the crushing and grinding process. It has been recognized for nearly three decades that grinding is the most expensive and least efficient stage in mineral processing (El-shall and Somasundaran, 1984). At that time it was estimated that grinding consumed between 25 and 70% of the total power required in mineral processing. This recognition drove the development of new stirred mill fine grinding technology in the 1990s (Jankovic et.al, 2003; Enderle et. al., 1997; Massey, 2008). These milling technologies have a reduced energy consumption compared to traditional fine grinding using ball mills. In the ?coarser? fine grinding applications this improvement is approximately 30%. The benefits increase to above 50% in ultrafine grinding applications (Lichter and Davey, 2006). Despite these gains, the US Department of Energy reported that an additional energy savings of up to 37% is possible in the minerals industry. They identified continuing research and development and implementing best practices in both grinding and materials handling as the primary avenues for the additional reduction (BCS, 2007).

Jan 1, 2011

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica surfaces immersed in solutions of hydrolysable cations and/or sodium oleate. Hydrophobic forces were observed at the pH range where the concentration of the singly-charged hydroxo-complexes (CaOH+ or MgOH+) in solution is the highest. In the absence of oleate, the adsorption of the hydroxo-complexes was indicated by the disappearance of the repulsive hydration force. These results suggest that the hydrolysable cations adsorb on silica as singly-charged hydroxo-complexes. Based on the results obtained in the present work, a model for the adsorption of hydrolysable cations has been developed.

Jan 1, 2009

By J. D. Morgan

Demand for nonfuel minerals depends on the overall state of the economy, which steadily improved each quarter in 1984. New housing starts rose to 1.8 million units. Automakers turned out about 15% more cars (7.8 million) and 30% more trucks (3.1 million) than in 1983. Nevertheless, many domestic mineral operations experienced difficulties in 1984. This resulted from import competition greater use of newer engineered materials, emphasis on multi-unit housing and downsizing of motor vehicles. About 15% of our energy was imported. This in cluded $36 billion worth of crude oil and $22 billion in refined products This added significantly to the overall merchandise trade deficit of $12; billion. On the bright side for mining, coal production rose 14% to 810 Mt (890 mil lion st). Three-fourths o: the coal was burned to generate electricity and more than half of our electricity was derived from coal-burning plants. With the exception of a few large-bulk, low-value raw minerals, most minerals move relatively freely in world trade. The strong dollar encouraged imports and made exporting more difficult. Consequently, our nonfuel minerals trade deficit rose 60% to $19 billion, reflecting imports of $39 billion and exports of $20 billion. There were increased pressures from some major segments of the minerals industry for some form of import protection. But President Reagan said, "Our goal is a system of free and fair trade in goods, services, and capital. We will work toward this goal through both bilateral and multilateral trading agreements." The US minerals industry consists of domestic mines, concentrators, smelters, refineries, mineral manufacturing plants, and recyclers. It also includes many wholly- or partially-owned operations in many parts of the world, providing employment and income for US citizens and others as well. Compared with 1983, the value of US raw nonfuel mineral output rose 8%, to $23 billion. The $253 billion worth of goods processed from this crude mineral output was a 14% increase. Major Metals Raw steel production - a major indicator of both material use and mineral production-rose 10%, to 84 Mt (93 million st). This stimulated a 36% rise in domestic iron ore production, to 52 Mt (57 million st), about 98% pelletized. Iron ore imports rose 44%, to 14 Mt (15 million st). Despite the increase of steel production, output remained well below levels of just a few years ago. For example, 1984 production was still 23% less than in 1981. Raw steelmaking capacity remained steady at 122 Mt (135 million st). The industry continued to cite steel imports as a major reason for low domestic capacity. In December, pacts with seven leading steel exporting nations were announced. This is an effort to reduce import penetration to about 18.5% of the domestic market. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about 50% capacity. The US mined no manganese or chromium. Only a small quantity of ferronickel was produced from domestic laterite mining in Oregon. Molybdenum production, at 45 kt (49,500 st), rose threefold. Mine shipments of tungsten, another mineral tied to steel

Jan 5, 1985

By R. Steele

In addition to compliance with government emissions and reporting requirements, mining and mineral processing companies are increasing energy efficiency to reduce costs and become more competitive in the global marketplace. One of the major obstacles to identifying opportunities for increased energy efficiency is the lack of readily available data on energy use, and more importantly the energy use linked to production data, that identify energy reduction opportunities. As well as energy reduction, mining and mineral processing companies often struggle with the prediction of energy use, and are often penalized for under or over forecasting. Once again, it is the lack of timely information that makes this prediction difficult. This paper looks at expanding the use of a Manufacturing Execution Systems by integrating with Energy Solutions. This will provide automatic, timely information, at a granularity that makes it easier to identify energy reduction opportunities, reduce energy costs, and better predict energy use in a mining and mineral processing operation.

Jan 1, 2011