Search Documents

By C. O. Lee

The Grand Isle Sulphur Mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, Louisiana. The depth of water at this location is about 50 feet. The deposit is on acreage covered by oil, gas, and mineral leases which were originally issued in favor of Humble Oil & Refining Company by the State of Louisiana, and which were continued, maintained, and redesignated by the Department of the Interior of the United States, pursuant to Section 6(b) of the Outer Continental Shelf Lands Act. On September 19, 1956, Freeport Sulphur Company acquired from Humble Oil & Refining Company the sulphur rights underlying the tracts. This assignment was approved by the Secretary of the Interior on July 12, 1957. The Director, United States Geological Survey, approved Freeport Sulphur Company as Operator on July 31, 1957. Actual design began in September 1956; the first structural contract was let December 15, 1957, and offshore erection began in June 1958. The initial phase of construction will be completed and production started in early 1960. The estimated total cost of the project is $30,- 000,000, of which $8,000,000 is the extra cost for being in the Gulf of Mexico.

Jan 1, 1959

By Alan D. Randolph

A size-continuous breakage kinetics model is postulated and supported with industrial grinding mill data. It is shown that the kinetics parameters include the effects of possible classification at the mill discharge. The estimated parameters were then used in the kinetics model to simulate the behavior of a grinding mill in open and closed circuit operation. While material transport and kinetics are equally important in open loop operation, heavy recycle in a closed circuit make a detailed material transport model for grinding unnecessary. In effect, the mill can be considered as backmixed. This suggests that more emphasis should be placed on modeling the classifier than the development of detailed material transport models for the grinding mill.

Jan 1, 1975

By Carlton H. Baab

In June, 1981 the Electric Power Research Institute (EPRI) issued a report titled "Control Systems in Coal Preparation Plants" to determine the status of instrumentation and automation systems in the coal preparation industry. EPRI concluded that the control systems presently being employed in the U.S. coal preparation plants "are relatively primitive compared with those in other mineral processing industries; and analytical instrumentation is virtually non-existent". Until recently, clean coal has had a low selling price and satisfying the purchasers' specifications required only minimum cleaning. However, it is becoming more apparent that the increases in coalfired utility power plants forced outage rates are relative to the deterioration in the quality of fired coal. Utility companies are becoming aware of the economic value of reducing the variability of ash, moisture and sulfur in steam coal purchase orders. New contracts are currently being negotiated between electric utilities and coal producers that include provisions for increased penalties if the product does not meet specifications. With tighter specifications on the quality of steam coal, interest is increasing in more sophisticated control systems. One type of device that is currently assisting the preparation plant operator optimize and control the coal cleaning process is nuclear based instrumentation. Nuclear instrumentation includes methods for measuring weight, level, and density as well as for performing elemental analysis on coal. This paper discusses the various types and applications of nuclear instrumentation currently in use in the coal preparation industry.

Jan 1, 1983

By D. W. Park

Longwall Strata Control and Maintenance System (LoSCoMS) is a software and data communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels including excessive shield load, low setting pressure, leg leakage and poor shield performance, eminent maintenance problems, etc. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems of their longwall panels. Two years of experience with this system is covered in this paper.

Jan 1, 1998

By Jerome E. Grader

Special-purpose analog computers are being profitably applied in the process industries to perform miscellaneoas online computing functions in situations where conventional measurement and/or control hardware cannot perform a required task satisfactorily. This paper will discuss the application of such equipment in the mining industry. It is divided into two parts, beginning with a description of operation of the hardware, followed by a discussion of several applications of the computers to mining industry control problems.

Jan 1, 1969

By R. F. Winkle

Shortly after World War II, considerable impetus was given to use of truck haulage in open pit mines by the manufacture of large off-highway trucks. Mine management was quick to utilize this more flexible approach to open pit operation and in the ensuing years much time and energy has been spent to improve the basic concept. Dramatic progress has been made in drilling, blasting, loading and hauling with much emphasis placed on equipment improvement. In general, haul roads in open pit mines and quarries have received rather perfunctory treatment in studies of surface mining operations. Their importance to the successful pit operation requires more than a brief sentence saying, "Good haul roads must be maintained." Haulage costs account for approximately one-third of total mining costs including general costs and about 90 percent of the total loading-haulage cycle time is consumed in travel, hence, good haul road planning, construction and maintenance are mandatory for a viable operation.

Jan 1, 1976

By Byron R. Berger

Disseminated Au-As-Hg mineralization is localized along the Getchell Fault system at the Getchell Mine in north-central Nevada. Replacement ore bodies occur in Cambrian carbonaceous limestone and limy shale beds. Cretaceous granodiorite, dacite porphyry, and andesite porphyry dikes parallel the fault zone and are spatially associated with the mineralization. Hydrothermal alteration and mineralization occur continuously along 4-5 km of the fault system, and extend more than 1 km down-dip. Alteration consists primarily of removal of carbonate and deposition of quartz, pyrite, and carbonaceous material. Marcasite, sericite, kaolinite, calcite, barite, and fluorite are common. Gold content reaches more than 43 ppm in parts of the altered zones and averaged 9.3 ppm in the mined ore bodies. For the mineralized zones as a whole arsenic averages 0.28%, and occurs primarily as realgar, orpiment, and arsenopyrite. Mercury (22 ppm) is finely disseminated and mercury-bearing minerals are seldom recognizeable. Accessory mineralization includes antimony (100 ppm), copper (47 ppm) , lead (18 ppm) , molybdenum (10 ppm) , tungsten (16 ppm) , and zinc (50 ppm) . Geologic field studies and K-Ar dating suggest that the mineralization is related to a hydrothermal system produced by the granodiorite and related dikes.

Jan 1, 1975

By Barbara B. Newlin, Emily Rosenberg, Marianne Snedeker

Whose longwalls perform best in Eastern underground mines? What is the latest legislation affecting slurry pipelines? What are the trace element constraints on magma genesis? How can process set points be controlled more economically without affecting product quality? Where can I get a paper presented at the Australian Coal Preparation Conference? If answers to questions like these can help with your management decisions, exploration plans, or market positioning, your firm should know about Information on Demand. Information on Demand, Inc. (IOD) is a research service available to SME members to help them get the facts needed to develop business plans. IOD can function as a research staff and data bank specialist for geologists, planning specialists, production managers, and engineers in all levels of the mining industry. Just dial 415-549-3259 and ask IOD for a copy of an obscure article, a comprehensive literature search, or a background report on a company, a process, or a product. Within a short time, IOD will have the information you need delivered to your office or worksite. Information on Demand has a bank of dial-up terminals that provide access to more than 200 business and technical data bases, including Lockheed's Dialog, CompuServe, InfoLine, The New York Times Information Bank, and other systems. These data banks contain more than 95% of the world's technical literature published in the last 10 years. There is no input required from individuals or companies. The data bases are maintained by publishers and are constantly updated with abstracts of articles, reports and reviews, and other text appearing in more than 5,000 engineering publications, as well as thousands of other trade and technical publications. The data bases are organized by subject and offer a speedy comprehensive survey of world literature. One data base, called Compendex, provides worldwide coverage of engineering publications, meetings, and reports. The Metadex data base abstracts literature on the science and practice of metallurgy, and can be accessed by commercial, compositional, and numerical alloy designations. PatSearch and Claims data bases enable IOD to determine what patents have been filed by a given entity, what international patents are equivalent to a US patent, and other vital patent information. In the non-technical arena, the Commerce Business Daily has daily updates of federal procurement information. The Federal Register is abstracted on-line in a data base, and ABI/Inform is a data base full of marketing and management information for all industries. IOD offers a free pamphlet listing these and other data bases. A typical literature search from IOD will produce 60-200 references with abstracts, and can be printed out off-line and mailed or transmitted directly to an electronic mailbox. Abstracts will often give all the information needed by the reader. At times, when the complete article or technical report is needed for further study, IOD will send a photocopy of the full text for a small additional fee. Patents, books, securities exchange filings, standards, and specifications can also be supplied by means of IOD's network in major libraries, such as Harvard, MIT, and The Library of Congress. A technical translation service is available for foreign

Jan 12, 1983

By Charles Bruce

Although much has been said about the high cost of exploration, both at home and overseas, little of a specific nature has been published on actual finding costs, if indeed such data has been developed. This contrasts sharply with our sister industry, petroleum, where finding costs for oil and gas are available for virtually any country In the world. The reason is largely attributable to the genetic complexity of the hard minerals, as opposed to petroleum, and the increasing difficulties we are facing in the search for new orebodies. We have available to us data on the annual exploration budgets of most of the major mining companies which show them to run into the tens of millions of dollars. My co-panelist, Dr. Walthier, Director - Corporation Exploration, St. Joe Minerals Corporation, New York, NY, summed up the feelings of many explorationists in a recent keynote address when he stated, "I would not recommend a mineral exploration program of a general nature in North America budgeted at less than three to four million dollars annually, spread over four to five years -- or smaller amounts for more years". We have the fact that many of the major companies now prefer to "buy into" a new mineral discovery, particularly overseas, because of the high-risk and high-cost of exploration. Is there, then, a place for the small investor, let us say with a budget of under $200,000 per year and, if so, where and how? This paper is directed toward the above question and is based on experience gained while managing a limited international exploration program, on a shoestring, over the past three years.

Jan 1, 1976

By Lloyd M. English

Accurate knowledge of the gas content of coal seams has always been important, according to the work of W. P. Diamond and J. R. Levine, 1981, but is becoming increasingly important for several reasons: Excessive gas emissions in the mine can create explosion hazards. Depletion of shallower coal reserves is forcing underground operations to greater depths where coal gas content is often greater. Natural gas prices and the need for new energy sources make naturally occurring coal gas a potential resource of economic interest. Information on coal gas content will impact mine designs, mine ventilation system specifications, and the effectiveness of methane control procedures used. Accurate resource assessment is needed for projecting and designing potential gas utilization enterprises. The emphasis upon methane hazards in mining operations, and upon potential methane utilization, has led us to improve upon the procedures used to determine coalbed methane levels.

Jan 1, 1984

By R. H. King

The Deserado Mine of Western Fuels- Utah Inc. installed a micro-computer based mine wide monitoring and control system for mine environment, beltway fire protection, belt operating parameters, and equipment power utilization. The Colorado School of Mines was funded by the U.S. Bureau of Mines to document, evaluate, and report on the system design, procurement, installation, tests, and operation. This paper results from that project. The paper compares planned activities such as installation and start up, procurement contract specifications and system layout with actual performance to develop recommendations for future installations by mine operators.

Jan 1, 1987

By Y. Jinnouchi

An air-pulsated jig has been widely adopted as a main coal washer. It may be mainly because of its many technical and economic features such as large capacity, low running cost, long life, etc. However, the recent increasing demand of fuel coal requires a higher productivity and efficiency of the air-pulsated jig. To fill this requirement theoretical and experimental investigations have been conducted on model and practical jigs in Japan. This paper generalizes the results of these investigations. In jig operation it is essentially of the most importance to create efficiently the pulsation of the water best suited for coal washing. The optimum pulsation should be determined by the theory of jigging process, and the method to realize it by that of pulsating mechanism.

Jan 1, 1982

By Donald D. Carr

Four counties in Indiana--LaPorte, Vigo, Vanderburgh, and Switzerland--have potential for deep underground limestone mining because they are in or are near high population areas and have no surface-minable limestone de- posits. The principal markets are Gary-South Bend, Terre Haute, Evansville, and Cincinnati. Minable seams suitable for aggregate are 120 to 150 meters (400 to 500 feet) below the surface in LaPorte and Vigo Counties, about 90 meters (300 feet) below the surface in Switzerland County, and about 600 meters (2,000 feet) below the surface in Vanderburgh County. Some deposits are also suitable for high-purity uses or for cement raw materials, which enhances their potential for exploitation.

Jan 1, 1980

By H. Kimura

A new technology for ironmaking based on direct gaseous reduction of iron ore concentrate is under development. The process is based on the flash reduction of the concentrate particles in a gaseous reducing agent, such as hydrogen, natural gas, a reducing gas generated by partial combustion of coal, or a combination thereof. This technology is expected to drastically lower CO2 emission and reduce energy consumption by about 38% of the blast furnace requirements. The energy savings are possible largely due to the elimination of pelletization and cokemaking. Process design and simulation using hydrogen as the reductant for iron ore concentrate have been performed. A process flow sheet composed of a flash reactor, heat recovery system, water removal system for purifying recycled hydrogen, and all connecting streams was evaluated using the METSIM software. Ironmaking using two reactors was also designed and simulated, which could reduce the total required amount of hydrogen although it would increase the complexity of the flow sheet and operation.

Jan 1, 2010

By P. -J. Kleiterp

Highwall mining is a mining method to extract coal from a final boundary in open cut mining, trench mining or contour mining. This boundary may have been reached because of economic constraints (economic strip limit) or geographic constraints (spoil heaps, rivers etc.). Coal is mined from visible, horizontal, or near horizontal coal seams by making rectangular, parallel, unsupported drives with an unmanned cutterhead and coal transport system. This is controlled from a mining unit, or launch frame, positioned outside the drive, in front of the highwall. Removal of overburden is not required or is limited to small quantities only. Highwall Mining originated in the 1940 in the Appalachian Coal Field. This paper describes the history of the various machines that have been designed for highwall mining. During the 1990 and later, there has been more emphasis on the safety in highwall mining. Many pillar strength formulae have been derived to determine the required width of pillars in highwall mining and, with that, the economic feasibility of highwall mining. The various pillar strength criteria will be discussed in this paper showing the countries where they are applied. In order to make highwall mining equipment safer and more productive, there have been quite some technological improvements applied to the machines. These technologies make highwall mining ready for the future as a serious mining method, also outside its traditional Appalachian mining area.

Jan 1, 2010

By M. K. McCarter

In 1963, a major expansion program at Kennecott's Bingham Canyon mine converted rail operation in the upper portion of the pit to truck haulage. Since that time truck-haulage capacity has increased to about 272 000 Mg (300,000 tons) per day. The majority of this production is waste material which is deposited in monolithic dumps located on the eastern slopes of the Oquirrh Mountains. The largest of these dumps, referred to as Copper Notch and Keystone, measures approximately 1830 m (6000 ft) in length, from 180 to 300 m (600 to 1000 ft) in height, and contains some 430 Tg (470 mil lion tons) of waste. The height, structure, rapid rate of growth, and anticipated leaching suggested the possibility of dump failure. In order to evaluate this possibility, an outside consulting firm was retained in 1966 to investigate the stability of the growing dumps. Their investigation indicated that, other than superficial movement, the waste dumps would be stable under static loading, and that soil distribution was not continuous enough to sustain massive foundation failure. Since this investigation, however, several failure processes have been observed. Crest settlement occurs frequently in response to compaction and over-steepening in the upper portion of the dump surface. Over-steepening results from accumulation of fines near the crest caused by natural segregation. Normally, coarse material, near the base of the dump, exhibits an angle of repose near 0.65 rad (37"). The fine material, however, stands as steep as 0.75 rad (40"). Periodic equilibrium adjustments cause stepwise settlement (Figure 1) of the dump surface and occasional sloughing of the protective berm. Routine surface preparation by dozers and graders and frequent inspections by supervisory personnel have proven adequate in preventing problems associated with this form of crest instability.

Jan 1, 1976

By F. W. Schweitzer

The trend toward development of large low grade ore bodies has accelerated in recent years. It has been estimated within the copper industry that "porphyry" type deposits will provide the bulk of copper production during the next 30 years. It is further estimated that in these deposits the average ore grade by the year 2000 will be 0.25% copper (1). Many of the new porphyry copper discoveries are of such extremely low grade that they are particularly sensitive to small fluctuations in cost variables and copper prices. Because haulage constitutes a major item of surface mining expense, the capability to transport large tonnages of material at increasingly lower unit costs is vital to the profitable operation of many of these mines. High capacity conveyor belts appear to have considerable promise in this area. The heaviest use of high tonnage conveyors has been in the brown coal industry in Germany. In the past 20 years several such installations have proven successful. In addition to the German installations, several other successful systems have been put into operation. Some examples are: The Oroville Dam project in the United States; the tar sand operation in Northwest Canada; the pre-mine stripping and mining of the Twin Buttes Mine in the United States; the Kursk Magnetite 'dine in the U.S.S.R.; and the Nchanga Copper Mine in Zambia. Most of the systems mentioned are handling alluvial material consisting mainly of fines. The noteworthy point regarding these installations is their high continuous capacity. One of the largest lignite mines in the world is at Fortuna, Germany, where over 15,700 tons (15,250mt) per hour of overburden is transported on an 87 inch (221cm) wide belt running, at over 1000 feet (305m) per minute.(2). Another example is a 20,000 ton (18,150mt) per hour system for loading iron ore into barges on the Great Lakes (3).

Jan 1, 1976

By E. Viet Howard

During the recent expansion of precipitate copper production at the Chino Mines Division of Kennecott Copper Corporation, Santa Rita, New Mexico, local studies of the dump leaching process were intensified. As these studies progressed it became apparent that a reliable method for locating leach solutions within the dump was required, since the contact between leach solutions and the copper-bearing material would determine, in great part, the recovery of values. In the past, the problem of determining leach solution contact has been attacked by various methods, including destructive testing (dump dissection), indirect observation (such as chloride or dye tracers), and mathematical or laboratory model studies. These methods have not proved completely satisfactory for the studies now being developed. Investigation of methods for in situ observation of leach solutions led to consideration of radiation logging in drill holes, which are petro¬leum exploration and development techniques for locating fluids and measuring porosity in the subsurface. Standard oil field logging equipment was leased, modified, and tested. After successful testing, the equipment was purchased for additional studies. Applications and results of the methods are described in this paper.

Jan 1, 1968

By J. F. Kvitfkovich, R. L. Bate

Coal production in the Central Appalachian region has a long history, and it remains a major US coal-producing region. The coal industry consensus is that the region is in a state of decline as evidenced by the recent lower regional output. Are Central Appalachian coal reserves adequate for the region to continue as a major supplier of low sulfur coal? To answer that question, this paper focuses on the Central Appalachian coal reserve base estimates and production trends. Central Appalachian (CAPP) reserve evaluations face the difficulty that there are no publicly available databases that provide a thorough analysis of remaining CAPP reserves. Based on best available Energy Information Administration (EIA) data, a coal reserve estimate of 17.6 billion tons is developed. This estimate appears high according to industry perception. Recent United States Geological Survey (USGS), and other state agency coal reserve estimation projects are evaluated as alternative approaches to the re-serve estimation problem. Using the conclusions from these studies, the CAPP reserve base is estimated at 7.1 billion tons. Another perspective on the CAPP reserve base is provided by reserve holdings of major CAPP operating companies reported at 5.2 billion tons. A conceptual mining cost analysis indicates substantial price increases will be necessary to offset this deterioration in the economic viability of the reserve base.

Jan 1, 2004

By Patricia Curtis Petty

Thirty years ago, the appearance of a female mining engineer, geologist or miner in a company, union or mine environment would have been unthought of, unwelcomed and violently opposed. Twenty years ago, the intellectual perception of the news that women were interested in becoming mining engineers, geologists and miners had been accepted by the industry-but no one wanted to be the first to hire one of these exotic creatures. Ten years ago, those who had been most vehemently opposed to the philosophical idea of women working in these areas were faced with competent, productive engineers, geologists and miners-who only incidentally happened to be women-and began hiring them. Historically, of course, one can always find the isolated individual who worked in these areas-the first female graduate of the Colorado School of Mines with a mining engineering degree graduated in 1903-but the concept of woman as professional engineer was very slow in arriving in the United States. The few who worked as miners generally worked in small family enterprises, such as some of the coal mines in both Eastern and Western United States. Others accompanied husbands or sons into wilderness areas searching for gold and other precious metals.

Jan 1, 1984