Search Documents

By David H. Carlson

Mechanical sorting of "poor" rock accumulated from past native copper mining operations has been under study at the Michigan Tech's Institute of Mineral Research for several years. Prior to this work, the poor rock dumps totaling approximately 9 million tons containing an estimated 35-70 million pounds of copper (1) have been considered mainly as a local source of road aggregate used from time to time and consequently of minor value. An electro¬mechanical sorting machine developed by International Sorting Systems Corporation of Santa Barbara, California has been tested for preconcentration of the waste rock before conventional milling (2,3). The ISSC machine has possibilities for underground preconcentration of crushed mine-run native copper ores. The objective of the study described here was to provide information about limi¬tations on sortability due to characteristics of the ore and present crushing practices. When the native copper mines were in operation prior to termination in 1969, two types of ore were produced, amygdaloidal and conglomeritic. In the first type copper occurs in vesicles left by gas bubbles entrapped during rapid cooling of the tops of lava flows. The conglomeritic ore beds consist of rounded pebbles and fragments cemented together by calcite, epidote, chlorite, and feldspar; the copper occurs around pebbles, in cracks, and sometimes as partial or total re¬placements of pebbles. The copper in the conglomeritic ore usually is in finer grain sizes than that in the amygdaloidal ore, and large (plus 4 inch) copper masses are virtually absent.

Jan 1, 1970

By P. M. Krishna

An example illustrates the use of ASTM Standard E901-82, Classification System for Uranium Resources. The example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that ,remain in fixing the classification of a given uranium resource include the uncertainty in estimating the quantity of undiscovered resources and resolving the differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1983

By D. G. Kotlyar

Oxidized sulfide minerals, commonly formed by weathering, increasingly are becoming important resources as primary sulfide deposits are depleted. Oxidation, in general, reduces selectivity and recovery in flotation. The objective of this research was to determine the mechanisms of oxidation and collector adsorption in sulfide systems as a step towards developing improved technologies for beneficiation of oxidized sulfides. Data from microcell flotation tests are combined with electrochemical and spectrophotometric measurements. The adsorption of ethyl xanthate (EX) on oxidized sulfides was characterized using AC impedance techniques and correlated to flotation response. The floatability of chalcocite, chalcopyrite and pyrite was dependent on the extent of oxidation. Oxidation for 1?) d at 65? C inhibited flotation of chalcocite, and chalcopyrite even after the addition of a large amount (1 x 10') M) of collector. Heavily oxidized (27 d) chalcocite remained unfloatable. However, longer oxidation of pyrite and chalcopyrite restored the floatability. Oxidation resulted in an electrically resistive, nonporous surface layer.

Jan 1, 1993

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill.

Jan 1, 1999

By Ruiren Jin

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II)-activated sphalerite exhibits a high flotability so that satisfied separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by IR; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitute and polymerization of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1987

By W. K. Dressel

Over 2 million tons of steel furnace dusts are produced each year in the United States. Recycling of these dusts rather than disposal would conserve mineral resources, reduce land requirements for disposal, and decrease pollution. In addition to the iron content, the dusts contain appreciable amounts of zinc and lead. Removal of lead and zinc with simultaneous reduction of Iron oxide has been achieved by inert atmosphere roasting of carbon-containing pellets prepared from steel furnace wastes. High- and low-carbon wastes were blended to obtain mixtures with sufficient carbon to serve as a reductant during subsequent roasting. The mixtures were pelletized with the addition of bentonite and water, and the dried pellets were roasted in a stream of nitrogen at temperatures ranging from 900" to 1,150° C. Zinc and lead contents were reduced to the 0.1 percent level or less by roasting mixtures containing as little as 7 percent carbon for 1 hour at 1,100° C. ton metallization increases with available carbon content; 50 percent metallization is achieved with 7 percent carbon, 85 percent metallization with 12.5 percent carbon, and over 95 percent metallization when the pelletized mixtures contained in excess of 20 percent carbon.

Jan 1, 1973

By Robert M. Lewis

Chemically, mica is a complex silicate of sodium, potassium and aluminum. There are no important uses of mica where the chemical analysis is important, except that in some uses of ground mica, the content of iron oxide present as an impurity must be kept to a very low limit. Muscovite mica is frequently found containing black and red "stain" as a homogeneous part of the books or sheets. In most cases this stain or impurity is magnetite or hematite. Some mica contains impurities deposited by infiltration. This is commonly a red stain, less often brown or white. The best mica is free from all such impurities, and the greater their content, the less value does the mica have.(1) It is because of these undesirable impurities that a large segment of the fine ground mica industry relies on weathered pegmatites and alaskite ores as a source of raw material. The mica concentrates obtained from these ores are relatively clean and require moderate beneficiation to meet color and density specifications. One need only to observe the stained and decrepitated condition of the mica recovered from mica schist to appreciate the challenge that processing this material presents. Despite these adversities there are several advantages to be gained by mining and processing mica schist ores. The mica content of these ores are considerably higher than the pegmatites and alaskite ores now being mined, often containing in excess of forty percent mica. This-higher grade mica feed should promote a lower mining and milling cost with its resulting competative advantage. With more rigid government

Jan 1, 1969

By Vladislav Kecojevic

Both Canada and the United States are endowed with significant reserves of mineral resources. Mining industries in these two countries have a strong safety and health culture; skilled, dedicated and well-paid workforce; applications of state-of-the art technologies and high productivity, strict environmental requirements and social responsibility. Both countries are global leaders in safe, economic, productive, environmentally responsible and sustainable mining practices. Mining schools/ departments in Canada and the United States provide a strong and comprehensive education and training, hands-on learning experience, with support for internships and co-op opportunities to prepare graduates for careers not only nationally but also in the global mining industry. While there are many similarities in their industries and mining schools, there are also some differences. This article examines the contribution of mining to the economy, the political climate, the regulatory framework, the investment climate, environmental regulations, the language, the perception of mining, news and press coverage, and the academic landscape in both countries. Opinions, observations and perspectives shared in this article are of the author, and do not necessarily reflect the views, policies or positions of any organization, employer or affiliated group.

Nov 1, 2025

By S. J. Schatzel, K. M. Ajayi, E. N. Rubinstein, Z. Khademian

This study simulates the impact of a shale gas well casing breach near a longwall mine. Field studies are conducted to measure mining-induced permeability changes over the abutment pillar of a longwall mine, and a geomechanical model is developed in 3DEC, a three-dimensional numerical modeling code, to predict the aperture of fractures in the overburden at the study site. The predicted aperture values are used to determine mining-induced permeabilities and the results are compared with the field measurements. These aperture values are provided as inputs into fracture flow code (FFC), which generates a stochastic discrete fracture network (DFN) model for the study site and predicts the potential shale gas flow to the mine. Results from 100 DFN realizations are statistically analyzed using the bootstrapping method to compensate for notable variation in fracture geometry. The results show a significant difference between the gas inflow for nearby panels due to increase in the induced permeability during mining of the second panel. The average gas flow to the mine was calculated as 4.72×10−2 m3/ s (49 cfm) for a hypothetical breach at the Sewickley horizon during the first panel mining, 8.97×10−3 m3/ s (19 cfm) for a hypothetical breach at the Uniontown horizon during the first panel mining, 2.16×10−1 m3/ s (458 cfm) for a hypothetical breach at the Sewickley horizon during the second panel mining, and 8.07×10−2 m3/ s (171 cfm) for a hypothetical breach at the Uniontown horizon during the second panel mining. Depending on the mine ventilation system, this could result in methane concentrations exceeding regulatory limits. Hence, these findings provide insights into the potential risk of an unconventional gas well casing breach near a longwall mine under shallow cover.

Feb 15, 2023

By M. Szatkowski

The studies conducted by Laplante and coworkers (1983,1984) with flotation of galena and quartz, showed that the rate of flotation reaches a maximum value for a certain intermediate value of the air flow rate. A similar, though less pronounced, effect of the air flow rate on the selectivity was also observed. Luttrell and coworkers (1985) showed that the size of air bubbles has a significant effect on both rate and selectivity of coal flotation. These two studies used flotation tests in which no froth layer was formed. This note describes effects of the air flow rate and bubble size on the rate constant and selectivity of coal flotation, using a mechanical laboratory machine with a froth layer allowed to form. Experimental A raw, dry ground Illinois coal was used in flotation tests. The size distribution and ash content of the samples are : Particle size (µm) Weight (%) Ash (%) +600 4.30 41.7 600/200 43.05 19.0 200/74 22.25 16.0 - 74 30.40 24.0 average 20.8 No. 2 fuel oil with a concentration of 200 g/t of feed and M.IBC with concentrations of 11, 22, and 33 mg/L of pulp (128, 256, 384 g/t, respectively) were used as flotation reagents. Tap water with a natural pH of 7.0 to 7.8 was used throughout the tests. No other reagents were used. The starting concentration of coal in the pulp was 86 g/L. A standard flotation machine with the pulp volume of 5 L was used in experiments. Three different air flow rates were employed, resulting in three air escape velocity values of 14, 30, and 70 cm/min. The air escape velocity (AEV) was calculated as the ratio of air flow rate (Qa) to the slurry surface (Ss) in the machine. For a comparison, the upper limit of air escape velocity values used in commercial size flotation machines is between 70 and 100 cm/min (WEMCO, 1983). A machine consisting of a generator of fine bubbles and a separatory column, described elsewhere (Szatkowski and Freyberger, 1985), was used for some tests where bubble size lower than that generated in the standard machines was required. Prior to a flotation test, a batch of coal was mixed with water in the flotation cell for at least 10 minutes to ensure that all coal was thoroughly wet. Then the specified amount of fuel oil was added and the pulp was conditioned for five minutes. The specified amount of MIBC was added 15 seconds before the end of conditioning. After air flow was opened, flotation products were collected for 0 to 30, 30 to 60, and 60 to 120 second intervals. Content of the combustible material in samples was determined by subtracting the ash content from 100%. A photographic technique was used to determine initial distributions of bubble size generated by the flotation machines. Bubbles generated in water containing the prescribed amount of the frother but no solids were photographed against a black background. The average diameter and standard deviation were then calculated for each set of flotation conditions. The method gives results reproducible within k 5% of the average bubble size. Table 1 contains information about the measured bubble size distributions expressed by the average bubble diameter (Db) and the standard deviation ( SD ) . Results and discussion The general formula for calculating the flotation selectivity is: o = recovery of coal/recovery of ash (1)

Jan 1, 1988

By E. H. Cho

A current environmental concern is the cleanup and restoration of soil contaminated with low-level radionuclides at DOE sites including the Nevada Test Site. At the present, there is no applicable process to economically and effectively deal with the remediation of contaminated soils. This situation requires development of a selective flotation process to separate the radionuclides from contaminated soil efficiently and economically. In this study, a minus 200 mesh size fraction of pure cerium dioxide was used as a surrogate for plutonium oxide which is the major contaminant at the Nevada Test Site. A Hallimond flotation cell was utilized to examine the flotation behavior of cerium dioxide with oleic acid under various conditions of pH and collector concentration Mechanical cell tests were conducted to float the surrogate from a mixture with uncontaminated Nevada Test Site soil in the absence and presence of calcium carbonate as a carrier. Two different sizes of the carrier (minus 150 mesh and 65-150 mesh) were tested. It was found through the Hallimond cell flotation tests that the cerium dioxide could be floated well at pH's 4 and 9 with 10-3 molar oleic acid. It was also found that the addition of the carrier drastically enhanced the flotation recovery of cerium dioxide. The flotation recovery of the surrogate increased from 34 % to 65 % by adding only 0.5 % calcium carbonate (minus 150 mesh) in the feed and also increased to 95 % by adding 10 % of this carrier to the feed. The finer size fraction of calcium carbonate (minus 150 mesh) was more effective in recovering cerium dioxide than the coarser size fraction (65-150 mesh) The flotation method utilizing a carrier of calcium carbonate seems to provide a high potential to be used for the remediation of soil contaminated with radionuclides at various Department of Energy's nuclear weapon sites.

Jan 1, 1996

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By A. B. Cecala

Enclosed cabs have been used for many years to isolate workers on mobile equipment in the mining industry for health and safety reasons. These enclosed cabs create a microenvironment for workers where they can be either more protected or more vulnerable to contaminants. Over the past decade, the U.S. National Institute for Occupational Safety and Health (NIOSH) has performed substantial research efforts to improve the air quality inside enclosed cabs of underground and surface mobile mining equipment. In these efforts, NIOSH has partnered with mining companies, original equipment manufacturers (OEMs) and manufacturers of filtration and pressurization systems in a synergistic effort to reduce respirable dust and improve the air quality inside these enclosed cabs. Various field studies over this time have shown an array of results ranging from very minor to very significant reductions (protection factor: 3-89) in respirable dust levels inside these enclosed cabs. In addition to and concurrent with the field work, NIOSH also performed a comprehensive laboratory study to evaluate all the factors involved in cab filtration and pressurization systems and identified those factors that were most significant for an effective system. From this comprehensive research effort, the key components for an effective filtration and pressurization system have been identified in an effort to provide the best air quality to equipment operators inside of enclosed cabs of mobile mining equipment, thus minimizing respirable dust exposure.

Jan 1, 2014

By Kwangmin Kim, Junnhyeok Park, Taehee Lee, Minkyu Kim

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. To address these concerns, this study examined the effectiveness of commercially available polymers, known for their biocompatible and environmentally friendly features, to prevent dust generation from upstream-type TSFs in active mining operations. It focused on two areas in TSFs: the tailings beach and slope/dike surfaces. Two types of polymers—polyethylene glycol and poloxamer—were selected, and their effectiveness was evaluated in a series of phased laboratory and field tests. The lab tests investigated the moisture-retention capacity of the tailings after treatment with the polymer solutions as well as the ability of these solutions to reduce dust emissions. Polymers were applied to a tailings bed surface in the lab and dust was generated from this surface using a wind tunnel. PM10 and PM2.5 concentrations were measured using laser-diffraction dust sensors, and the polymers were found to have reduced dust emissions up to 95%. Small-scale wind-blowing tests were conducted in the field (specifically, in a controlled environment at a TSF) to evaluate polymer effectiveness on the tailings beach and slope/dike areas. The tests revealed that the AP could efficiently suppress approximately 80% of PM10 and PM2.5 dust emissions at both types of areas. Finally, 1000 gallons of AP solution were discharged at the top of tailings beach and slope/dike areas, respectively, and found to be effective. The results of these tests showed the high potential of the biocompatible polymers to be a feasible solution for reducing the respirable dust emissions from upstream TSFs in arid and semi-arid regions.

A kinetic model for leaching of various metals with different lixiviants in a batch system has been developed. Material balances for reactants and products at the solid/liquid interface were formulated and solutions to these balances were obtained in view of practical conditions. Special emphasis has been given to examine mixed controlled reaction systems where both heterogenous reaction and mass transfer play important role on the overall rate expression. The resulting kinetic expressions for either powder or rotating disc are discussed in light of experimental findings for various metals. Examples of the metal dissolution systems considered in this study include cobalt, nickel, copper and gold in acid, cyanide or ammoniacal solutions.

Jan 1, 1992

By C. McAllister, D. Preece, J. Berendzen

"The Multiple Blasthole Fragmentation (MBF) model models multiple explosive charge contributions and the effect on fragmentation of delay timing with its associated scatter for each blasthole. The model uses near-field blast vibration attenuation parameters and the ground p-wave velocity as inputs for part of the in situ rock property to model rock fragmentation. It models most blast design parameters explicitly and simulates the effect of wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges within a blasthole or among blastholes. The fragmentation size is calculated at three-dimensional grid points within a blast, and the fines and oversized blocks are treated explicitly. The model takes a surveyed irregular geometry of the free face of a blast as the calculation boundary.This paper presents a case study on applying the MBF model at an openpit mine. Near-field vibration measurements from signature hole blasts were conducted to obtain the stress-wave magnitude and attenuation parameters as well as ground sonic velocity. A production blast was then monitored with the corresponding fragmentation measured, serving as site-specific inputs to the MBF model. Various blast design scenarios were then simulated to develop ones that provide better fragmentation to improve mill throughput for the mine. IntroductionThe semiempirical fragmentation models currently found in the literature (Cunningham, 1987; Lownds, 1995) cannot explicitly model contributions from multiple blastholes with varying delay intervals. Most of these models are not three-dimensional. Furthermore, these models predict an average fragmentation size within a volume surrounding a blasthole and use the average size to generate a size distribution over the volume. The percentage of fines and oversize blocks is included in the distribution. Typically, such models are inadequate for predicting fines and oversize blocks (Cunningham, 1987)."

Oct 1, 2016

By Edwin S. Smith

One of the many responsibilities of mining engineers and mill superintendents is to provide for the safe and economic disposal of wastes (or tailings) remaining after a mineral has been extracted from an ore. The cost of disposal of these tailings exerts a considerable influence on the minimum grade of ore extracted from the mine. It varies to a great extent with each project and is dependent on many diverse factors, such as the local topographical, meteorolgical, geological and seismological conditions together with the applicable water pollution laws of the area. The process used to extract a mineral from an ore determines the physical characteristics of the tailings and thus is one of the more important factors to be considered when planning disposal facilities. Today's trends .in ore-processing operations complicate the problems of waste disposal: recently developed extraction methods result in the production of finer tailings, the use of lower grade ores produces greater volumes of wastes, while the enhanced land values in the vicinity of industrial plants preclude the former practice of spreading wastes laterally and force the expansion of waste desposits upwards to greater heights. The frequent occurrence of stability problems in waste deposits indicates that many mining organizations may not be employing current soil mechanics concepts and practices. One of the most spectacular, and often most disastrous, types of tailings dike failure is that resulting from liquefaction of the fine particles combined with a breach of the main retaining dike.

Jan 1, 1967

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By David H. Dahlem

Uranium is a very mobile element geochemically and is widely dispersed in the lithosphere and hydrosphere. Under oxidizing conditions, it is particularly widespread and appears in all parts of the surface hydrologic system. As a result, this system is a leading candidate in uranium-resource assessments as a new base from which total resources might be estimated. No other sampling system provides the large volume geochemical capture as the continental hydrosphere and is as pervasive and non-selective regardless of rock type. However, the water system as a uranium metal sampler is not without drawbacks as the development of a National sampling program based on it has shown, In spring 1973, the National Uranium Resource Evaluation (NURE) was announced by the U. S. Atomic Energy Commission (AEC). The program was conceived to provide an evaluation of the domestic uranium resources and to identify areas favorable for uranium exploration. The specific NURE objectives are as follows (Bowyer, 1974): 1. To provide a preliminary evaluation of domestic resources and favorable exploration areas by early 1976, based on existing data. 2. To conduct a comprehensive evaluation of domestic resources and favorable areas by 1980, based on advanced state-of-the-art information. 3. To conduct an R&D program into new and improved procedures, equipment, and technology for uranium exploration and assessment. 4. To disseminate information on new exploration concepts and technology.

Jan 1, 1976