Search Documents

By O. J. Tassicker

The Electric Power Research Institute (EPRI) initiated a program in 1976 to develop and demonstrate an instrument system for on-line continuous measurement of coal properties. The program has focused on the use of Prompt Neutron Activation Analysis (PNAA) for elemental determinations and microwave absorption for moisture determination. One of the major results of the EPRI program is the development of the CONAC (Continuous On-Line Analysis of Coal) instrument, with Science Applications, Inc. (SAI) as the prime contractor and Kennedy Van Saun Corporation as a subcontractor.

Jan 1, 1983

By Robert H. Hooff

The Vor-Siv Dewatering and Classifying Unit was developed by the Polish Coal Industry because of a need for a unit that would dewater and classify high volumes of solids in water slurry. To be practical, the unit needed to be relatively small in size, simple in design, involve low operating costs, and be able to give a dewatered product of less than 30% moisture. The answer to the above mentioned criteria was the Vortex Dewatering Sieve or, as we refer to it, the Vor-Siv. The original installation of the unit, as we know it today, began in 1963 when the Pols installed the unit in a full scale pilot application. By 1966, at least 30 of these units were installed throughout the Polish Coal Industry. This equipment was originally introduced in the United States in 1966 at the Fifth International Coal Preparation Meeting in Pittsburgh, Pennsylvania. The first installation in the United States was not achieved until 1970, when Mr. Fred Sachs of The Valley Camp Coal Company, Triadelphia, West Virginia, installed a Vor-Siv in a retrofit application. To date, there are 36 Vor-Sivs installed in this country and 29 in the process of being installed or delivered.

Jan 1, 1976

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

By C. J. Konya, A. Konya

"Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industry, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, the optimization of explosive load, as well as prediction methods for the environmental affects for the technique of Precision Presplitting. BACKGROUND Methods of controlled blasting in which a smooth, stable wall could be blasted have been an important consideration since blasting in mining and construction has begun. How can one use an explosive, with its massive energy and power, to break a non-homogenous rock without causing backbreak, poor walls, or deviations in the wall over large distances? The blasting industry has known for a long time that blasting ‘high benches’ would result in better walls and less backbreak. However, this was not a sufficiently controlled technique for critical projects, such as the Niagara Power Plant. This was one of the main challenges Hercules Powder faced when they began the project. In order to achieve this, they used a new tool in the explosive engineer’s toolkit, presplitting. The presplitting done on the Niagara Power Project utilized 1 ½” x 8” (38mm x 203mm) 40% gelatin dynamite in 2 ½” (63.5) diameter boreholes. This was done on multiple levels with benches between 12 feet to 52 feet (3.6m to 15.8m) with a total powder factor of 0.75 pounds/cubic yard (0.45 kg/m3). The spacing on these holes ranged between 18 inches to 24 inches (0.46m to 0.61m), center to center (Langfors & Kihlstrom, 1973). The strange aspect of this project was that this “lightly loaded” closely spaced row was fired before the production blast, yet this project produced some of the best walls seen at that time directly from blasting. In today’s blasting industry, presplitting is a more common way to produce smooth, stable high-walls for both the construction and the mining industry. Today, explosive loads for traditional presplitting is generally measured in pounds per foot (kilograms per meter) and typically ranges from 0.30 lb. /ft. to 0.5 lb. /ft. (0.45 kg/m to 0.75 kg/m). MECHANICS OF PRESPLITTING When analyzing a blasting process like the Niagara Project, many wonder how did that work when normally confining a charge would cause cratering and increased backbreak. Since then, presplitting mechanics have been studied extensively. It has been shown in many models that presplitting is not achieve through the collision of shockwave, but by gas pressure in the boreholes. In addition to models and finite element simulations, this has been proven full scale using Pyrodex, a propellant, to create a presplit plane with no shock wave present (Konya, Dean Barrett, & Smith Jr, Presplitting Granite Using Pyrodex, A Propellant, 1986)."

Jan 1, 2017

By J. R. Schafler, J. L. Brinkman

"The US coal mining industry has suffered a recent decline in profits caused by a combination of decline in commodity demand and more restrictive government regulation, forcing coal mining companies to cease production in numerous mines. A 40% decrease in the total number of coal mines occurred from 1994 to 2000. The number of mines remained relatively constant until 2008 when a change of government sparked a series of new environmental regulations which have contributed to another 15% decrease from 2008 to 2016. In contrast, production has only decreased by 3%, increasing from 1994 to 2008, and then decreasing since 2008. However, this value is skewed by large increases in sub-bituminous coal production and decreases in other coal ranks. Several aspects assist in executive decisions on mine longevity and economic worth. Studies of open source mine data collected by mandated government surveys coupled with commodity history can be used to find relationships between mine closures and these elements, which include statistics on production tonnage, seam height, coal rank, etc. This paper looks at coal mining trends since 1994 by comparing mine, market, and regulation factors that may influence mine closure. INTRODUCTION The US coal mining industry is currently experiencing a decline in both demand and commodity price while facing implementation of more stringent air and water pollution regulations. Company profits have decreased significantly, forcing several major companies to declare bankruptcy. The industry was required to adapt to survive. Many of these companies have adjusted by abandoning mines; the last two decades have seen a drastic decrease in the number of mines. To discover the primary causes of this downturn, three major aspects must be studied: properties of abandoned mines, commodity history, and regulatory impact. TRENDS SINCE 1994 Each year, US coal mines are required to submit data on a wide variety of categories to the Mine Safety and Health Administration (MSHA) and the US Energy Information Administration (EIA). This data includes administrative records, production values, and information regarding the attributes of the mined material and the mine itself. Each year since 1996, EIA has released a report summarizing the data from two years prior. Additionally, MSHA maintains a database containing a collection of all the most current data. These resources are the primary sources for the following figures."

Jan 1, 2017

By B. W. Lawrence

Shaft alignment requirements are consistently met using conventional shaft sinking methods. Little attention has been given to achieving similar alignment accuracies using rotary drilled shaft methods. Alignment of these shafts is difficult to control and guarantee. Bare shafts and shafts that use drum hoisting systems can accept some deviation. However, combining drilled shafts with Koepe hoist installations presents new accuracy requirements for drilled shafts. This paper describes the importance of verticality with practical examples, and discusses various methods of measuring verticality and their respective limitations.

Jan 1, 1989

By Z. Sample, S. Kaushik

"INTRODUCTION Industries around the globe have been making significant advancements in recent years due to innovations in automation technology. With the implementation of modern automation technology, professionals in process automation or plant operations can expect significant and exciting change, and the mining and mineral processing industries are no exception. From 2000 to 2010, the International Council on Mining & Metals (ICMM) reported that an increased output and increased value of most metals has resulted in a rise in global metal and mineral process industries from $214 billion to $644 billion. [1] Since most productivity increases in mining and mineral process industries have been achieved through the ability to process lower grade ores with improved efficiency and larger equipment, these industries have begun to adopt advanced automation and control technologies. Despite a growth slow-down, the mining and mineral processing industries are poised for continued and sustainable growth and development due to an increasing demand for energy minerals and emerging technologies requiring minerals and metals previously not demand. However, as these industries becomes more automated, new challenges are arising on the horizon. DEMOGRAPHIC TIME BOMB John Payne from BP is credited with first using the term Demographic Time Bomb to describe the upcoming crisis in the process industry in finding experienced operations personnel. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years. This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, this implies that these skilled mining and mineral process professionals are an aging population with irreplaceable knowledge and experience that are expected to retire in the next 5-10 years. While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences."

Jan 1, 2015

By X. P. Zheng, H. K. Lin

Barium fluorophlogopites were synthesized in the laboratory to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between the layer structure and the Ba-O bond length. The higher the barium content, the larger the cell volume and distance between the layer structure, and the longer the Ba-0 bond, the more negatively charged the surface is, and, hence, the more easily adsorbed are cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1995

By N. S. Tanious

This work was completed prior to the author's appointment with the Nuclear Regulatory Commission (NRC). Therefore the views and conclusions contained in this paper are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the NRC. Reference to specific brands, instruments, or trade names is made to facilitate understanding and does not imply endorsement by the author or the NRC.

Jan 1, 1987

By ETHAN FUSTER, Richard Ray Jr, STEPHEN LEE

The abstract states that horizontally-mounted jet fans are commonly used to ventilate vehicular tunnels due to their space and cost savings compared to fully ducted systems. It highlights the successful use of vertically-mounted jet fans in exhaust ventilation shafts for a passenger rail overbuild in New York City. The paper compares shaft dimensions, jet fan placement, and measured airflows, also comparing these measurements to predictions from computational fluid dynamics (CFD) simulations.

Mar 16, 2022

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By Weiran Zuo, Wanzhong Yin, Jin Yao, Keqiang Chen, Qiuyue Sheng, Liu Liu

It is important to investigate the liberation properties of gangue minerals and establish liberation models for low-grade iron ores to reject gangue early. In this study, three types of iron ores from different iron deposits were ground to different particle size distributions by locked-cycle grinding and batch grinding. The liberation distribution of quartz, the most dominant gangue mineral among the three types of iron ores, was tested by Mineral Liberation Analyzer (MLA). Afterward, the liberation distribution of the three types of quartz was fitted using the beta distribution function, and their shape parameters were related to particle sizes to develop the liberation model. MLA test results showed that the liberation distribution of quartz with different grinding methods was basically the same. The developed liberation model predicted the liberation distribution of quartz in low-grade iron ores from different iron deposits well, and its coefficient of determination (R2) was between 0.90 and 0.98. This study deepens the understanding of the liberation rules of quartz in low-grade iron ores from different iron deposits, and on this basis, a more efficient liberation model based on the beta distribution function is developed.

Oct 18, 2023

By Paul B. Valenti

The Nevada Moly Operation of Anaconda Minerals Co., (a molybdenum/copper ore body) was initiated in 1978, with a contract to Bechtel Civil and Minerals Inc. for construction of a mining and milling facility near Tonopah, NV. Ground was broken on the concentrator portion of the project in August 1979$ with a multi-phased startup of the mill beginning in June 1981. Processing design tonnage of 20 000 t/d (22,000 STPD) was reached in early 1982. Major pitfalls of rapid design and implementation of engineering, construction, and startup are considered. The operation of the concentrator including SAG milling, ball milling, bulk rougher flotation, copper/moly separation, moly regrinding and cleaning, thickening, and product loadout are discussed.

Jan 1, 1983

By R. Wisniewski

Every underground coal mine in the United States must deploy and operate a wireless communication and tracking system. This paper addresses the reliability and availability of an installed tracking system and the communications infrastructure that supports it. A particular interest is the requirements for the systems to operate continuously without failure after a mine disaster for 96 hours, and the requirements in the MINER Act for the tracking systems to be ?calculated to be serviceable? and the communications systems ?redundancy?. These requirements imply a certain reliability and availability. This paper describes a quantitative way to assess these systems requirements, using the tools that are available and commonly used by the Reliability, Maintainability, & Availability community.

Feb 23, 2014

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH's that were in place within the study area, the results showed a possible elimination of 34 DDH's without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

By B. Kolonja

This paper considers simulation of truck dispatching system designs using maximum expected production of the truck-shovel system as the measure of performance. Two methods are utilized, multiple comparisons with the best (MCB) and the combination of MCB and the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. The results show that the combined procedure of MCB with CRN is the superior tool to reduce the total number of replications needed to ensure the specified probability of correct selection over the finite number of designing systems. In this case study, MCB with CRN reduces the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1994

By Elham Najafi, Sina Ghassa, Ata Akcil, Hadi Abdollahi, Sandeep Panda, Zohreh Boroumand

The present study investigates the influence of ferrous iron (as FeSO4) and ferric iron (as Fe2 (SO4)3), and pyrite (FeS2) on the ability of bacterial leaching of a high-grade sulfide Zn–Pb ore. In this regard, shake flask experiments were carried out at 5% (w/v) pulp density of the ore sample (having 40.7% Zn and 12.4% Pb initial metal content) using a consortium of mesophilic iron and sulfur-oxidizing acidophiles. A concentration of 0.04 mol/L of ferric iron in the leaching media was found to be optimum for zinc extraction without affecting growth of the microorganisms. Under this concentration, the dissolution of Zn, Pb, Cd, and As was found to be 57%, 0.2%, 0.03%, and 9.9% in 25 days. Using ferrous iron in the media, 0.16 mol/L of Fe2+ was found to be the optimum concentration for efficient bacterial growth and metal dissolution (54.6% Zn, 0.08% Pb, 0.03% Cd, and 10.2% As) from the sample in 25 days. On the other hand, using pyrite as the source of energy for bacterial growth, an initial 12-day lag period was observed when compared to the effect of ferrous iron in the media. Under the optimum concentration (test with 0.24 mol/L iron in the form of pyrite), the dissolution of Zn, Pb, Cd, and As was found to be 39.8%, 0.1%, 0.03%, and 10% in 25 days. The surface chemistry analysis indicated formation of a sulfur layer over the particle surface that hindered reagent diffusion and affected metal recovery through bioleaching.

By E. H. Cho

An acid mine drainage sludge sample containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn was obtained from the central part of West Virginia and leached with sulfuric acid at pH 3 and at room temperature. Air was bubbled through the leach solution to precipitate the iron content from the solution at pH 4.5. The leach solution contained 258ppm Zn, 105ppm Ni, 90ppm Co and 2050ppm Mn. Three distinctive solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA, Cyanex 272, and then Lix 84. The AIO ratio was 1 and the extractants were diluted 10 times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to pH 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1993

By S. S. Klima, D. E. Pollock, J. A. Organiscak

"Airborne respirable coal dust capture by water sprays or wet scrubbers has been studied and developed over many decades as an engineering control to reduce dust exposure in coal mines and combat coal worker pneumoconiosis. Empirical relationships and deterministic models for particular dust capture experiments have previously been devised to show the key parameters involved in airborne coal dust capture. Many of the results from these models show that the significant parameters related to airborne dust capture are water spray pressure, water quantity, water droplet size, relative water droplet-to-dust particle velocity, and total operating air pressure of the scrubber. However, many airborne dust capture efficiency relationships and models developed for particular experiments cannot be readily applied to forecast the dust collection efficiency of different spray and scrubber design configurations, which rely on several key dimensional engineering measures. This study examines engineering measures from previous water spray and wet scrubber experiments conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and the U.S. Bureau of Mines (USBM) to develop empirical models for wet collection of airborne dusts. A dimensionless empirical model developed for predicting airborne dust capture efficiency of water sprays and wet scrubbers is presented. IntroductionWater sprays have been one of the earliest mainstay engineering controls used to suppress respirable dust in underground coal mines. Some of the earliest reports of water spray usage on continuous mining machines indicated respirable coal mine dust reductions of 20 to 60 percent (Kobrick, 1970). Not long after the enactment of the 1969 Coal Mine Health and Safety Act, the U.S. Bureau of Mines (USBM) and others conducted extensive research into water spray and wet scrubber systems to control respirable dust in coal mines. The primary aspects of water spray dust control included prewetting for dust prevention, localized ventilation redirection and airborne dust capture, which are summarized in handbooks or best-practices guides (Kost, Yingling and Mondics, 1981; Kissell, 2003; Colinet et al., 2010). Initially, underground studies were conducted to identify the primary sources of dust during the mining processes and effective dust controls (Courtney, Jayaraman and Behum, 1978; Jankowski and Organiscak, 1983). Laboratory research systematically studied ventilation and airborne dust capture effects of water sprays and scrubbers to improve their application in underground coal mines (Tomb, Emmerling and Kellner, 1972; Divers and Janosik, 1978, 1980; Grigal et al., 1982; Ruggieri et al., 1983; Jayaraman, Jankowski and Kissell, 1985; Volkwein, Ruggieri et al., 1985; Jayaraman, Schroeder and Kissell, 1986; Divers, Jankowski and Kelly, 1987; Jones and James, 1987)."

Jan 10, 2018

By W. J. Wuest

The U.S. Bureau of Mines (USBM) has recently developed a rock mass classification system for evaluating the structural competency of bedded roof strata; the Coal Mine Roof Rating, or CMRR. When compiled with the companion Lotus 1-2-3 spreadsheet, which is simple to learn and use, CMRR data are a useful tool with applications to longwall gate road pillar design, safety hazard mapping, and artificial roof support analysis. This paper demonstrates these applications under actual conditions found in current U.S. mining operations.

Jan 1, 1995