Search Documents

By E. Cameron

Yeelirrie lies toward the center of Western Australia, 650 km (404 miles) northeast of Perth (Fig. 1). The ore reserves have been estimated as 52.5 kt (57,871 tons) of contained U3O8, at an average grade of 0.15%, of which almost two-thirds average 0.24% U3O8. the ore body is a thin, elliptical, more or less horizontal sheet measuring approximately 9 km (5.6 miles) in length, between 0.5 and 1.5 km (0.3 and 0.9 miles) in width, and up to 7 m (23 ft) in thickness, extending from the surface to a depth of 8 m (26 ft). In spite of its near surface position, there is only one small outcrop of significant mineralization. Carnotite is the only uranium mineral recognized so far, dispersed through a calcrete horizon, and deposited from circulating ground water which was also responsible for the carbonation of the clays completely filling an Early Tertiary drainage system. Calcrete, as seen at Yeelirrie, is quite distinct from the widespread, thin pedogenic horizons, as it often forms bodies many kilometers in length and up to 20 m (65.6 ft) in thickness, elongated parallel to the drainage lines. It is variously referred to as "valley calcrete" or "ground water calcrete" to emphasize the occurrence and mode of origin. The discovery of Yeelirrie in mid-1971 was the successful culmination of a grass-roots exploration program initiated in 1968 as part of Western Mining Cop's program of diversification from its historical position as a major gold producer. The object was simply to find an economic uranium deposit - with no constaints other than those normally taken as applying in the mineral search. There was, therefore, complete freedom in the selection of the exploration model, or models, to be applied and the areas to be considered, though the choice was inevitably influenced by both the nature of world occurrences and the local geology. One of the options avail- able was the sandstone environment. Yeelirrie was the direct result of pursuing this line of investigation through three sequential, but quite distinct, stages: first, a regional study; second, establishing a case for exploring the inland drainage systems of Western Australia; and finally, an evaluation of the calcrete environment. An assessment of the potential for sandstone-type deposits in Australia necessitated going back to first principles, since there were no known precedents in this country for guiding exploration and, as a consequence, the search need not be influenced by established prejudices. Previous uranium exploration during the 1950s had been preoccupied with vein-type deposits, and, although the sandstone environment was undoubtedly being examined in 1968, no discoveries had been announced to that time. When considering the necessary ingredients -a source of leachable uranium, a circulating ground water system, and a suitable reducing environment - it could be argued that considerable areas in the eastern part of the continent were theoretically prospective, but basin depth and the extensive superficial cover of Mesozoic and Cainozoic sediments presented considerable practical difficulties.

Jan 1, 1991

By Xiaoting Li, Richard Adasiak, Benjamin Mirabile

Pumpable J-Crib stopping walls and Jennmar high-strength (HS) stopping panel walls are widely used for resisting high-ventilation air pressures and roof support in underground mines due to their installation efficiency, convergence allowance, and better performance than traditional concrete block stopping walls. Based on the different entry dimensions and required maximum ventilation air pressures of up to 36-in. water gauge, 24-, 27-, 30-, and 36-in.-diameter pumpable J-Crib stopping walls, or 18- to 30-in. thick Jennmar HS stopping panel walls can be designed, and their support capacities and convergence allowances are evaluated for better roof control. Pumpable J-Crib stopping walls consist of 0.187-in.-diameter steel wire reinforced, JCrib material-filled bags, and non-wire-reinforced filler bags in between. Jennmar HS stopping panel walls consist of two, 20-gauge (0.04-in.-thick), galvanized, cold-formed steel panels with J-Seal materials pumped in between. Based on the fundamental structural design principles and specifications of ACI 318-19(22), the compression and flexural strength, and shear resistance of the walls can be checked to be compliant with the codes and specifications following the load and resistance factor design (LRFD) method. Specifically, the 0.187- in.-diameter steel wires in the pumpable J-Crib walls and 20-gauge steel panels in the HS stopping walls are integral parts of the walls and are considered to effectively confine the J-Crib or J-Seal materials. These steel elements play a significant role in reinforcing and improving the strength or support capacity of the stopping walls from a structural design perspective. Because of the high ductility of low-density J-Crib/J-Seal materials and steel elements, these walls are good at accommodating or absorbing the roof convergence (≥5% entry height), which cannot be matched by a traditional concrete block stopping wall (Figure 1). Based on the successful design and application of these stopping walls in different mines for improving roof stability and avoiding the air leakage, the authors have formulated the design methodology and verified independently by the finite element analysis (FEA) simulation technique. This design methodology combines the fundamental structural design principles with specific wall dimensions and material properties, facilitating mine engineers and government agencies to understand the in-depth working mechanism of these stopping walls.

Jul 1, 2023

By V. T. McLemore

"Production of industrial minerals remains important to the rural economy of New Mexico. In 2014, some 240 mines were registered in New Mexico, including 25 industrial mineral operations and 189 aggregate operations. New Mexico leads domestic production of potash, perlite, zeolite, and travertine. Other production includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica, and decorative stone. New Mexico has potential for additional production of industrial minerals. One company is exploring for garnet. Cretaceous black sandstones in the San Juan Basin have drawn interest for titanium, rare earth elements (REE), and zircon. Other REE deposits are being explored. REE-Th-U veins are found in the Gallinas, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Recent exploration has occurred for beryllium in the San Mateo Mountains, Iron Mountain, and Victorio districts. Companies also are examining High-Ca limestone and High-Mg dolomite for potential development. Aggregate continues to be important in urban areas and along highways. INTRODUCTION Industrial minerals and rocks are literally the building blocks of our way of life and they are an exceptionally diverse and vital group of raw materials that underpin almost all aspects of human activity, infrastructure, and standard of living. Industrial minerals and rocks are used in the manufacture of many products, from ceramics to plastics and refractories to paper. Although industrial minerals permeate every aspect of daily life, their presence and their role are typically invisible. A widely used definition of industrial minerals and rocks is “any rock, mineral, or other naturally occurring substance of economic value, exclusive of metal ores, mineral fuels, and gemstones: one of the non-metallics” (Bates, 1975). This definition includes the important construction materials sector as well as specialized industrial minerals, but complex interactions between consumer industries produce a number of apparent anomalies to this definition. Some metals are included as industrial minerals because their use is industrial rather than as a metal. Sulfur is now predominantly extracted as a by-product of cleaning natural gas, one of the world's major energy fuels. Production of industrial minerals has been and remains important to the rural economy of New Mexico. Industrial minerals constitute nearly 40% of the more than $2.8 billion generated by mineral production in New Mexico in 2013 (Table 1, see APPENDIX). In 2015, some 240 mines were registered in New Mexico. This total includes 25 industrial mineral operations and 189 aggregate operations. New Mexico leads domestic production in potash, perlite, zeolite, and travertine. Other industrial minerals production from New Mexico includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica, and decorative stone. Additional production statistics are in Harben et al. (2008). Major industrial mineral districts are shown in Figure 1."

Jan 1, 2016

By M. H. Rauschkolb, J. A. Cremeens

Geotechnical solutions were developed for closure of two historic, remote underground mines in the deserts of southern California. Closure criteria included access closure, minimal site impact, and optimum use of native materials. The closure designs and construction activities incorporated techniques for protecting sensitive biota, particularly bats and desert tortoise. The types of mine openings that were closed include adits, declines, shafts, daylighted stopes, and dugout dwellings. The desert locations permitted implementation of cost-effective closure techniques that relied upon the use of native materials. The strategies and techniques developed for these desert closures are adaptable to other climates.

Jan 1, 2002

By Harry Wolf

The chemistry of the element uranium enables industry to employ either an acid or alkaline carbonate leach solution for most uranium ores. Either method my be used for conventional, in-situ, or heap leaching. Uranium recovery in the leaching process depends both on the solubility of the uranium minerals and, on the access of the leach reagent to them. The uranium leaching rate is proportional to the liberated mineral surface area and the chemical reactions involved in the dissolution step. The dissolution of U(VI) and the oxidation of u(IV) to U(VI) are the basic chemical reactions in the leaching process. The active surface area is a function of the effective porosity and the particle size of the ore (1). Ore pieces, with a high porosity and high permeability, may provide a large active surface area even in coarser fractions. This type of ore might be suitable for heap or in-situ leaching techniques. Nonporous and impervious ores are usually more amenable to conventional milling where the active mineral surface is exposed by grinding the ore down to the liberation size of the mineral.

Jan 1, 1981

By J. Villeneuve

Steady-state simulation has proved to be a very useful aid in designing new plants and optimizing existing ones. The algorithms and data definitions of existing simulators often, however, require a great deal of expertise for implementing a simulation-based methodology. The constraints imposed by conventional simulators are explained and the advantages of a new algorithm, the Objective-Driven Simulation, are shown. These advantages are a) an improvement in the simulation results, which enables simplifications of the methodologies used, and b) the possibility of taking into account economic objectives for plant operation, thus extending the range of application of steady-state simulation.

Jan 1, 1992

By Paul H. Johnson

The CH Leaching process is a new, more sophisticated, form of gold, silver, uranium and sulfide copper heap leaching wherein each layer of a multi-layered heap is divided into a number of independent cells, each of which are successively formed and leached in the top layer of the heap to their maximum economic recoveries, and then rinsed and sealed from further leaching. Triangular earth berms form the outside walls of the heap and a gridwork of rock-filled berms on top of the bottom pad form independent under- heap solution storage zones. The high degree of solution recirculation and staging that occurs in this process produces a relatively small volume of very rich pregnant solution. The cellular heap design and its mode of operation result in a uniform, intensive, long-term leach for all of the ore particles in the heap. Besides improved metal recoveries, the process appears to have several cost and operating advantages. In the CR2MR process, sulfuric acid and a soluble sulfide are added to a gold and/or silver pregnant leach liquor to precipitate most of the contained silver, mercury, copper, etc. as sulfides at a pH below 2.5. The other product of the reaction is solubilized HCN. Following a liquid-solid separation step, cyanide is regenerated in the supernatant solution by raising the pH to a level above 9.0. This process regenerates a portion of the cyanide used in the leaching step, removes contaminant ion species (silver, copper, mercury, etc.) from the leach solution and, in a subsequent step, recovers the gold in an enriched form. It is believed that substantial cost savings may be experienced by the use of this process in some gold and/or silver leach systems.

Jan 1, 1984

By Joseph P. Sobanski, Michael P. Bruen

The North Branch tunnel segment of the Tunnel and Reservoir Plan Mainstream System consists of 14,075 m (45,885 ft) of 9.2 m (30.2 ft) finished diameter and985 m (3,232 ft) of 2.5 m (8.25 ft) finished diameter concrete lined rock tunnels. The TBM mining and concrete lining methods used in completing this $166million project differed from “typical” TARP construction methods in that a two-stage concrete lining was placed and the lining was initially placed concurrently with TBM mining as a two pass system in the same tunnel segment. For the main tunnel (9.85 m diameter), TBM mining averaged 24 m/day (79 ft/day), excluding downtime associated with two main bearing changes, and the concrete lining placement, averaged 117 m/day (380 ft/day) and 53 m/day (174 ft/day) for the invert and arch segments, respectively.

Jan 1, 1999

By J. B. Lott

The authors' company has recently undertaken a development programme aimed at exploring the relationships between the variables of greatest importance in the design of mixer-settlers for metallurgical solvent extraction applications. Such applications vary from relatively small scale plants treating copper mine waters, nickel containing effluents, etc., where the total flowrates may be of the order of a few hundreds of gallons per minute, to very large scale plants treating several thousands of gallons per minute of leach liquors containing copper, uranium or other metals. This paper outlines the physical and mechanical factors which must be taken into account when designing mixer-settler systems for large scam. solvent extraction plants. The performance of the equipment will also be dependent upon the chemistry of the system, including the kinetics and thermodynamics of the ion exchange reaction itself, the effect of impurities flocculants, surfactants, temperature, etc., but these will not be dealt with here. Much of the laboratory work has been carried out using copper containing solutions and either LIX 64* or LIX 64N* as the solvent dissolved in various grades of kerosene. For simplicity, all the graphs and tables of results which are presented and discussed here will refer to the LIX-copper system, although the conclusions will in many cases be generally applicable to other systems also. The LIX-copper process is now sufficiently well known to obviate the need for a full description, however, an outline flowsheet of the process is shown in Figure 1. The ultimate objective of a laboratory programme for a particular extraction application is to provide data upon which a mixer-settler system can be designed to handle a given throughput of leach liquor and extract from this liquor the maximum quantity of metal for the minimum cost. In other words, the objective is to determine the design and operating parameters which achieve the optimum balance between capital and operating costs. * Trade-marks for General Mills solvents.

Jan 1, 1971

By Jonathan G. Price

Silver-copper-lead deposlts in Precambrian, Permian, and Cretaceous red-bed sequences near Van Horn, Texas, have the following features In common: (1) mineralization controlled by steeply dipping fractures in sandstones, (2) lack of ore In overlying and interbedded limestones, (3) absence of igneous intrusions, (4) sulfide ores without typical hydrothermal gangue minerals, and (5) associated arsenic, molybdenum, zinc, and cadmium but not gold. Ore was probably deposited along fractures by reaction between low-temperature, oxidizing, metal-rich ground waters and sulfide-bearing waters or rocks. Detailed mapping and studies of fracture patterns indicate that mineralization occurred during Basin and Range extensional deformation, thereby postdating major Trans-Pecos igneous activity.

Jan 1, 1983

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

Disruption in critical minerals supply chains has resulted in the evaluation of various types of mineral deposits for critical minerals potential. Much of the study on critical minerals focuses on occurrence and characterization, but little research has addressed what concentrations of critical minerals in a mineral deposit are required to make an exploration target into an operating mine. Understanding the cut-off grades of ore deposits being actively mined is one criterion to determine if concentrations in an exploration target are high enough. Cut-off grade is defined as the minimum amount of mineral contained in a ton of ore that is sent to the processing plant. Among many factors, cut-off grade depends upon the size and type of the deposit and mining operation, the processing technique, and market prices. This research does not aim to define cut-offs for determining if a mineral deposit is economic. Rather, it defines estimates of concentrations of critical minerals that could be considered good enough for further exploration. For example, ~2% total rare earth oxide (TREO) is the cut-off grade for Mt. Pass carbonatite, but 500 ppm TREO could be an exploration target for coals.

Feb 1, 2025

By H. E. Rudi

The advent of open nit mining permitted the development and processing of minerals never before thought possible. New equipment was needed; new techniques were devised; new methods were called for. This development and acquisition of new techniques, methods and equipment did not, however, stir the souls of our industry and educational leaders sufficiently to a recognition of the problem of people, especially the future development of the people needed in open-pit mining. The people problem has been and will be with us as long as there are two of them. The development of people will be required for the same reason. The problem of developing future personnel for open-pit mining is not what must be developed; that is known to all of us and can be briefly stated ashore and better of everything." As I see it, the real problem lies in determining (1) what personnel are really critical, (2) why are they critical and (3) how can we develop them.

Jan 1, 1965

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1987

By Y. Zhang, C. Zhou, M. Girman

Wireless technologies are increasingly being implemented in underground mines for various purposes such as communications, tracking, remote control, remote sensing, and environmental monitoring. However, the adoption comes with risks as common wireless systems, such as WiFi, Bluetooth, IWT (Innovative Wireless Technologies) wireless system, often operate in the unlicensed ISM (industrial, scientific, and medical) band. The shared nature of the ISM band can lead to interference among devices and consequently cause performance degradation and reliability issues. In this study, we developed two wireless communication evaluation boards as a tool to evaluate the performance and reliability of a wireless system with the presence of electromagnetic interferences (EMI) from other wireless systems in underground environments. We adjusted various parameters including signal power from adjacent frequency channels, noise power within the same channel, the movement of personnel, and communication packet size. Our findings indicate that, while the power of the EMI source plays a key role, the motion of personnel in the tunnel also has a strong impact on performance, and this impact increases as the power of EMI sources increases. In noisy environments, smaller packet sizes are preferable as they enhance the likelihood of successful transmission. High levels of interference or noise can lead to increased packet loss or error rates, potentially causing communication links to fail completely or become ineffective. The evaluation boards utilized in this study are based on a practical wireless transmission system deployed in a remote controller for a heavy mining machinery used in underground coal mines. The results and findings presented in this paper can aid in the design of wireless systems that are resilient to EMI in underground mining environments.

Feb 1, 2025

By MOHAMMED AMINE BELMI, ANAS DRIOUCH, ABDELAZIZ LAHMILI, LATIFA OUADIF

For many years, underground workings in the Bou Azzer mine have been challenged by geotechnical problems related to the serpentinite instability. The stage of evaluation of the compression potential is crucial to develop an appropriate drilling method and the choice of non-standard support. This research work presents a retro-analysis of serpentinite behavior in underground excavations at different depths, using a multi-approach method, based on several empirical and semi-empirical and theoretical-analytical methods, calibrated by the observational method. The analysis performed in this work reveals that underground excavations in Bouazzer East and Ait Hmane area would encounter compression problems that were recognized as the most serious from a depth of 300 m because of the effects of lithology and tectonics. Therefore, the Aghbar region has a slightly negligible compression potential. The compressive failure mechanism in this mine, depending on the mechanical strength, is started at induced stress of 9 MPa.

Nov 27, 2021

By Cheng Li, Yanlei Wang, Lingrui Kong, Jianxin Tang, Fang Yuan

Coal mined-out areas have a significant impact on mining safety and affect the pressure distributions of neighboring coal faces. The PFC3D software is used to study the goaf mechanical characteristics, and the core loading test verifies the rationality of the numerical simulation method. The results from the numerical modeling showed that the void ratio, particle size ratio, and particle size distribution of the rock particle sample (RPS) had a significantly remarkable influence on the compression deformation characteristics of the rock block. The parallel-bond tensile strength and parallel-bond cohesion had a notable impact on the compression deformation traits of the rock block only when the axial stress level was lower than 12 MPa. By contrast, when the axial stress exceeded 5 MPa, the effective modulus significantly influenced the compression deformation features. However, the stiffness ratio, loading rate, and parallel-bond friction angle had almost no effect on the compression deformation characteristics. Furthermore, when the stress level was less than 10 MPa, the stress–strain curves from the rock core samples’ numerical simulation and loading tests were approximately linear. In addition, the Pearson correlation coefficients of the stress–strain curves suggest that the goaf zone’s core numerical simulation results had a robust correlation with the loading test results. The findings of this study can serve as a reference for the field application of PFC3D software and safety assessments in goaves.

Jan 18, 2022

By Qingwen Shi, Yun Zhao, Brijes Mishra

The effect of discontinuities on the fracturing and mechanical behavior of shale has been extensively investigated on a laboratory scale in previous works. It is well agreed that the lamination properties, including discontinuity and lamina properties, affect the behavior of shale. However, it is still unclear how the lamination properties are affecting the stability of the shale roof in an underground coal mine entry. This paper investigated the effect of lamination properties using the discrete element method on a mine-scale entry model as an extension to the previous work conducted on laboratory scale models.

Jan 11, 2022

By Hasan Nizamoğlu, M. Deniz Turan, MÜCEVHER TURAN, RAMAZAN ORHAN

Tailings (flotation waste) that is formed during copper production may be considered in the class of valuable wastes due to the amount of copper it contains. Owing to the decreasing grade values in copper ores, utilization of wastes such as tailings that carry certain amounts of copper as secondary sources has become a necessity in both the economic and environmental sense. This study investigated the usage conditions of five different ammonia salts as leaching reactants for the purpose of selective extraction of copper from tailings. For this purpose, the effects of parameters such as leaching temperature and leaching time were examined at different concentrations of ammonium hydroxide, ammonium carbonate, ammonium nitrate, ammonium chloride, and ammonium persulfate. The copper extraction efficiency in the case of using the aforementioned salts by themselves were listed as (NH4)2CO3 (73%) > (NH4)2S2O8 (69%) > NH4OH (64%) > NH4Cl (42%) > NH4NO3 (40%). The highest copper extraction efficiency was obtained in the leaching process that was conducted with the solutions obtained by mixing ammonia salts in the best conditions. Accordingly, as a result of 6 h of leaching at 30 °C in the presence of 22.5% NH4OH and 100 g/L (NH4)2S2O8, 91.47%of the copper was transferred into the

Jun 3, 2020

By S. W. Swerson

25.1-THE PURCHASING FUNCTION The word "purchase" means "to obtain by paying money or its equivalent; to buy for a price." This definition is all too simple to properly describe the word "purchase." One should consider the basic objectives of purchasing-to procure the right material, of the right quality, in the right quantity, at the right time, from the right source at the right price. Here it should be noted that in purchasing it is recognized that the best quality or grade of materials may be the only grade to purchase for a specific job. However. there are other jobs where the medium, standard or poor grade of materials is the right quality, as the lesser grade will perform adequately. In some companies the purchasing department makes the decision as to the right quality, while in others this function is shared with other departments. Years ago in business the owners controlled the purchase of required materials and services by performing the task themselves. The owners obtained the type materials and services they needed and paid the price demanded. This function was performed along with all the other duties requisite to the owner of a business, namely, clerical, hiring and firing of personnel, financial management, etc. As companies grew in size, clerical duties were assigned to other personnel and the owner usually retained the purchasing authority. This same division exists today in many small companies. However, in the larger companies, the purchasing function has been assigned to a separate department. Importance of the Purchasing Function-The larger the company the greater the need for a separate department to perform the purchasing function. Today the purchasing agent for most larger progressive companies has policy-making authority. Therefore, it is reasonable for him to report to the president or vice president of his company. Studies of several hundred companies show the purchasing department head reporting to top management 87.5% of the time. This fact in itself is indicative of the importance of recognizing that effective purchasing requires a department staffed with specialists in the field of procurement with knowledge and experience sufficient to perform in today's complicated business atmosphere. In the manufacturing field it is a common axiom that usually half of the company's dollar expenditures are for materials. If a purchasing department functions properly and the right product or service is purchased and a savings accomplished, the contribution to the net profit of the company is much greater, as opposed to sale dollars, where only a small portion is carried forward to net profit. Thus, the importance of the purchasing department and the contribution it can make to the success of the company are obvious. 25.1.1-THE PURCHASING FUNCTION 1. Responsibilities of the Purchasing Function-The purchasing agent in performing his function is acting as an agent for the company and others in the company requiring materials and services. Accordingly, he is committing the company for materials and services subject to certain limitations which the board of directors may stipulate. In view of this, the purchasing agent,'^ position must of necessity he

Jan 1, 1973

By W. R. Reed, J. P. Rider

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a mediumsized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-tobailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. IntroductionIn surface mines, production drilling is an essential process in blasting to fracture the hard rock overburden for removal. During the process, considerable amounts of respirable dust are produced. Past sampling at the shroud area of blasthole drills had documented time-weighted-average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 (Organiscak and Page, 1995) and 1.04 to 52.30 mg/m3 (Listak and Reed, 2007). These high dust concentrations, which may contain silica, can lead to respirable dust overexposures for the miners working nearby. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal.Two basic methods are used to control drilling dust: a wet suppression system or a dry collection system (Cecala et al., 2012). Dry drilling techniques using a dust collection system are preferred in rural mining locations where a constant water supply is not available, and in the case of rotary drilling where water is associated with accelerated bit wear due to bearing degradation and hydrogen embrittlement. In addition, dry drilling eliminates freezing-related issues with water in colder climates. Dry dust collectors are highly effective at removing dust, especially the finer material, as long as they are properly operated and maintained (Listak and Reed, 2007; Organiscak and Page, 2005)."

Nov 1, 2016