Search Documents

By William G. Pariseau

The flexure of geologic strata, a phenomenon of inter- est to geologists and mining engineers alike, is examined as a sheet bending problem' in Coulomb plasticity. Formulae for the distribution of stress, strain and displacement increments, volume change, change in the length of the central surface and power of dissipation, as well as for the neutral surface shift are given. Strains of any magnitude are considered. The analysis shows that deeply buried strata may bend and develop "tensile" cracks under generally compressive states of stress. It is also shown that bed separation and high capacity props are desirable in mechanized longwall mining, a result in keeping with operating experience. Although speculative at this time, the analysis provides a rational working hypothesis as regards the problem of strata flexure and control.

Jan 1, 1968

By John L. Shafer

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in-situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent "leachability" of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corporation (ORC), the corporate R&D for Occidental Petroleum has under-taken a modest effort to address the question of "how to best identify and determine the information necessary to predict and control the operation of an in-situ leach for the economic recovery of copper."

Jan 1, 1977

By J. C. Johnson

The problem of estimating pillar capacity in coal mines has motivated development of a variety of empirical equations. Most of these equations have arisen from experience and a very limited set of measurements that have, necessarily, been focused on particular regions or coal fields. Their applicability is often limited to a specific range of pillar sizes. This is of particular concern in the design of large gateroad pillars and small barrier pillars between panels. The result has been a variety of equations and equation coefficients that can calculate load estimates to size pillars. Inclusion of these equations in more sophisticated loading models, such as boundary element methods (e.g. LaModel and MULSIM) has been hampered by absence of a function that describes specific variation of coal strength within the pillar. A singular exception, to our knowledge, is a function corresponding to the Bieniawski pillar strength equation. Because of this, it is the only coal strength criteria inherently available in most boundary element models. This paper presents a general method for deriving local coal strength, as a function of distance from the pillar rib, for an arbitrary pillar strength equation. Integration of this function provides the strength of pillar regions, or cells, needed for boundary element models. The method is demonstrated for the Bieniawski, Maleki and Holland-Gaddy equations. The Maleki and Holland-Gaddy equations contrast strongly with Bieniawski as strengths are extrapolated to large pillars and barriers. This development provides a tool for incorporating any of the proposed empirical equations into a boundary element model, thereby allowing the analyst to choose the most appropriate equation for a particular region, coal seam and/or pillar size.

Feb 23, 2014

By Charles H. Dowding

INTRODUCTION "On many projects, the tendency is to drop interest and support of the geological service as soon as it seems safe. That . . . is a short-sighted policy . . . It would be of further service perhaps to learn whether predictions were reasonably true to life." --C.P. Berkey, 1938 (3) This paper quantitatively compares predicted and encountered shear zone size and location and rock type for tunnels in the Colorado Mineral Belt. The Colarado Mineral Belt is composed of igneous formations with associated metamorphic rocks and faulting. As such, it represents the most complex of provinces for at-grade predictions (27). Shear zone and rock type data are assumed to be statistically homogeneous because of the common geology of the seven tunnels. It is often felt by geologists and engineers that the amount of information from which a geological model is created is so low that any statistical inferences are unstable. In other words, the addition of new data may drastically alter the means and variances suggested by the model. Therefore, predictions are rarely couched in quantitative statistical terms but modified with "probably," "most likely" or "possibly." Comparison of predicted and encountered data from past geological models will permit the "probably's" to be quantified and distilled from the art of geological prediction. To date, two other studies of the validity of predictions have been made (26 and 16). Together, these two studies indicate that

Jan 1, 1976

By R. R. Guzman

In this study, the "Mine Project Risk Management" methodology, MPRM (Botin et al. 2011), has been applied to characterize the sources of uncertainty and to quantify risk in the mining engineering stages of Block Caving mining method. As the result, rock mass caveability and ore fragmentation were identified as the two most relevant parameters of this process and a methodological model has been developed to quantify the risk associated to each of these two parameters. Furthermore, the applicability of the proposed model has been validated using as a case study the Chuquicamata Underground Mine Project in Chile.

Feb 23, 2014

By Rameshwar Sah, PK GHORUI, LR SINGH, SIVALINGARAJU BARISETTY, SHYAM YADAV

Fly ash is a by-product generated by the combustion of coal in thermal power plants. Its disposal is a major environmental concern for these power plants. Though a considerable part of fly ash is used in cement making and brick manufacturing, a substantial quantity remains unutilized. Bentonite is commonly used as binder in the micropelletization of process waste to attain the mechanical strength required for handling and transportation. The present paper deals with the partial replacement of bentonite with fly ash in the micropelletization process without affecting the quality of the micropellets. The mechanisms of both the binders are discussed. The bonding of particles by bentonite is a physical mechanism, while fly-ash bonding is a chemical mechanism. Silica and alumina are the major constituents present in fly ash along with lime. In the presence of water, the alumino-silicates and unhydrated lime present in fly ash undergo a pozzolanic reaction and form cementitious bonds, which hold the particles together. Use of fly ash as alternative binder for bentonite has cost benefits besides providing a better utilization option for fly ash.

By William Gleason

"In a time that seems to be dominated with nothing but bad news coming from the mining industry, there is a success story that has been quietly happening in Southwestern Wyoming for more than 60 years, and it is one that is likely to continue for many decades to come.Beneath the wind swept high desert plains of Sweetwater County, WY, about 32 km (20 miles) west of Green River, lies the Green River Basin where five companies, including Tata Chemicals North America (TCNA), are mining the world’s largest known deposit of trona and, in turn, are collectively producing 15.3 Mt/a (17 million stpy) of soda ash.“We have a long-term growth story that has been, and will continue to be a steady earner for many years to come,” said J. Martin Keighley, managing director of TCNA who has been in charge of the mine, formerly known as General Chemical Industrial Products Inc., for Tata Chemicals for about three years.According to the U.S. Bureau of Land Management (BLM), Keighley is safe with his prediction of future success. The BLM estimates that there are enough reserves in the Green River Basin to last another 2,000 years. Currently, four trona beds in the Green River Basin are being mined and in all, there are 25 major trona beds that occur within the Wilkins Peak Member of the Upper Eocene Age Green River Formation. The trona deposit as a whole covers about 2,500 km2 (1,000 sq miles) within the Green River Basin.And imagine, this economic mainstay in the region was discovered accidently.Prior to 1948, soda ash, the salable commodity that comes from trona and is used in a host of products including glass and detergent, was produced synthetically. In 1938, an oil and gas exploration team working in the Green River Basin came away with a find that would change the soda ash industry and the physical and employment landscape of southwestern Wyoming forever. Within 10 years, the communities of Green River and Rock Springs, which were built largely on the back of coal mining and railroads, had another commodity beneath their feet."

Jul 1, 2016

By Douglas W. Huber

During the past decade, a general awareness of the need for and subsequent development of increased safety in United States coal mines has taken place. Government and industry alike were stimulated into accelerating their actions through unacceptable accident statistics and costs (in terms of human misery dollar values). Those of us who work in the United States coal industry are aware of the development of governmental controls on nine safety. Both Federal and State regulations have placed increased responsibility upon mine owners and operators to insure a safe working environment and to provide training for miners. No other industrial group of workers has received such attention or, in our opinion, deserves it more.

Jan 1, 1982

By David A. Milligan

This paper describes the Darwin Silver Recovery project, located 66 km (40 miles) outside of Lone Pine, near Darwin, Inyo County, California. A lead-zinc mine and a flotation concentrator were operated there from 1945 to 1957. By the time the mine was shut down, 1.53 Tg (1.69 million short tons) of tailings had been stored in ponds. An average silver assay of 47 mg/kg (1.38 troy oz/st) of tailings stimulated interest for commercial silver recovery. A heap leach process was developed in 1981 at the Tucson Research Center of Anaconda Minerals Company, a division of Atlantic Richfield Company. Agglomeration techniques were used on the ore since the fine grind did not allow direct heap leaching. Lime and cement were required as binders, Early laboratory tests showed that recoveries equal to those from an agitated leach could be achieved at lower capital and operating costs. Laboratory tests determined cyanide requirements, lime and cement usages, and percolation or leach rates, as well as confirming that a zinc precipitation step could recover the silver from the leach solution.

Jan 1, 1983

By T. Kawashima

The expanding volume of maritime coal transportation is intensifying the problems concerning large vessel service port construction, transshipment and environmental control. The major problem is the transshipment of coal. Customary methods for bulk transfer must be improved and/or new systems developed. Slurry unloading has a key role in the new systems. The present report reviews progress in slurry transportation research which has been done in Japan since the 1960s when large scale experiments for domestic transportation were done. Experiments on the effects of vibration on the slurry cargo and on reslurrying are discussed.

Jan 1, 1982

By Mehmet Ali Recai Önal, MAHMUT CAMALAN

Mineral liberation is one of the primary objectives in comminution circuits for the downstream separation of valuable minerals. Breaking minerals through their grain boundaries (grain-boundary breakage) enables mineral liberation in their natural grain size, removing the need for intensive grinding. This study aimed to evaluate if gaseous carbon dioxide, oxygen, or hydrogen can be used as grinding additives to promote the liberation of chromite grains by grain-boundary breakage. For this purpose, chromite ore particles in the −9.53 + 6.35 mm size fraction were pretreated by exposing them to carbon dioxide, oxygen, or hydrogen flow. Then, the untreated and pretreated samples were broken in a drop-weight tester under the same conditions. Finally, the graderecovery plots of chromite grains in the selected progeny size fractions and the overall progeny distributions were measured and compared. Pretreatment with carbon dioxide flow was found beneficial for grain-boundary breakage. It significantly enhanced the liberation of coarse chromite grains along with the overall progeny fineness. EPMAanalysis showed that the adsorption of carbon dioxide seems to reduce aluminum concentration at grain boundaries, which could be the reason for grain-boundary weakening. These results suggest that carbon dioxide can be used as a grinding additive, reducing the carbon footprint of the mining industry.

Oct 29, 2020

By Walter E. Dean

Deep-sea manganese nodules are considered to be potential ores of manganese, nickel, cobalt, and copper. Considerable time, effort, and funds have been applied to the study of Se distribution of nodules on the sea floor and the location of economically important areas, but little effort has been spent in understanding the origin of nodules. Most theories that have been proposed to explain the origin of manganese nodules have been based on inorganic physicochemical processes. It is not by coincidence, however, that the area considered to be most economically feasible is in the zone of high biological productivity in the eastern equatorial Pacific Ocean and underlain by siliceous biogenic sediment. The genesis of manganese nodules and the concentration of many trace elements are intimately associated with biological processes.

Jan 1, 1982

By Cyrus W. Field

The Pacific Northwest as defined in this review comprises an exceedingly large and geologically complex terrain that occupies the 'Western Cordillera mobile tectonic belt. This metallogenic province is approximately 2100 miles long and 350 to 500 miles wide. It extends north-northwest from northern California and Nevada, through western Idaho and Montana, Oregon, Washington, British Columbia, and southwestern Yukon Territory, to southern Alaska, and west from the western flank of the Northern Rocky Mountains to the continental margin (Fig. 1). Many detailed and thorough exploration programs that have been conducted by mining and petroleum companies for over a decade have demonstrated that porphyry-type deposits are both numerous and wide-spread throughout this province. Although the Granby Mining Company extracted about 34 million tons of copper sulfide ore from Copper Mountain during the period 1900-1957, intentional large-scale production of porphyry-type ores was first initiated in 1962. It began at Bethlehem Copper Corporation's East Jersey orebody in the Highland Valley District of south-central British Columbia, approximately eight years after Mr. H. H. Huestis rediscovered that broad zone of copper-molybdenum metallization and recognized its potential significance.

Jan 1, 1973

By Thomas M. Lynberg

WIDCO is a surface coal mine located near Centralia, Washington. The WIDCO preparation plant processes over 7 million tons of run- of-mine coal each year with a product yield averaging 72%. In the jig type preparation plant the fine refuse amounts to approximately 130 dry tons per hour of 28mesh by 0. This fine refuse material is thickened in a 160ft. diameter static thickener with the use of lime as a coagulant and organic polymer as a flocculant. Once thickened the fine refuse, which is predominately bentonitic clays, has been dewatered and disposed of using several different methods. These methods will be discussed and include vacuum disc filters, ponds, solid bowl centrifuges, belt filter presses and experiments with electrokinetic dewatering.

Jan 1, 1981

By A. Anttila, S. Persson

The grinding mill is probably the most common unit operation in mineral processing. There is, however, much that can still be done in the way of optimization. This paper discusses the results of a well-controlled pilot-scale test in which the performance of a tumbling mill equipped with a conventional rubber lining and lifter bars was compared to a tumbling mill equipped with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14% more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case, grinding with a -20-mm ball charge required 26% less grinding energy than grinding with a -30-mm ball charge. The energy savings can, in most cases, be converted to an increase in capacity. The wear of the grinding media is difficult to assess over a short test period, but the results suggest that the wear is somewhat less when a smooth lining is used. A determination of the wear of the linings was not included in this study, but it is generally accepted that the use of magnetic linings reduces the lining costs dramatically. Computer simulation using the Millsoft code developed by Mishra et al. confirms and explains the increased effectiveness of comminution when a smooth lining and smaller grinding balls are used.

Jan 1, 2000

An upgrade to Vale?s existing Clarabelle dual-pinion, semiautogenous (SAG) mill was completed by the power and automation technology company, ABB. The mill is used to reduce the size of the ore at the company?s nickel and copper mines in the Sudbury area. The project was completed on time and on budget with an excellent safety record. Located in Ontario about 400 km (250 miles) north of Toronto, Vale?s Sudbury operations are primarily underground nickel sulfide mines, with integrated mining, milling, smelting and refining operations. One of the characteristics of Clarabelle Mill is to accept nickel-copper ore from various sources and companies and to produce a nickel-copper concentrate and copper concentrate for further processing. The size of the ore is further reduced in SAG mills, rod mills and ball mills, where all milling is done wet.

Mar 1, 2014

By Jan M. Mutmansky

Since 1973 when the first edition of the SME Mining Engineering Handbook was published, many significant changes have occurred in the US mining industry. The industry went through a fairly prosperous period immediately after 1973, but then many economic pressures came to bear on mining companies, particularly in the metal and coal branches of the industry. These pressures changed both the mining methods used and the general economics of the mining methods. As a result, the industry today is different in many ways titan it was in 1973. A general summary of some of the more important changes that have come about will be provided here as well as some assessment of the effects of these changes on the choices of mining methods. In the metal mining industry, the most significant trends were increased surface mining, the use of larger and more efficient equipment, and increased technology and automation. The primary impetus for these changes was unprecedented competition from foreign producers. In many cases, this competition came about because of the nationalization of foreign mines and the tendency for these mines to become a source of foreign exchange. Under these circumstances, the mines could be operated even though they were not profitable. As a result, domestic

Jan 1, 2008

By L. Yan, N. Damiano, J. Bickson, E. Bauer, D. Yantek, B. Whisner, M. Reyes, J. Srednicki

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35°C (95°F) [1]. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by >5.6°C (10°F) in mines with elevated mine strata and air temperatures. In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35°C (95°F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy. INTRODUCTION The apparent temperature inside an occupied RA could be significantly affected by the surrounding environment’s thermal conditions, such as mine air temperature and mine strata temperature. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and air velocity. It is used to assess the perception of indoor temperatures. Depending on factors such as geographic location and season, mine air temperature, relative humidity, and mine strata, temperatures can vary significantly [2]. RAs located in cold mines may pass the 96-hour 35°C (95°F) AT limit test that poses a challenge for RAs located in hot mines. One solution in these cases is that the occupancy of the RA could be derated (i.e., the RA occupancy could be reduced) to ensure the AT limit is not reached. However, this would require mines to purchase additional RAs to accommodate all personnel in the mine. For mines with high temperatures (above 26.7°C or 80°F), the occupancy might have to be reduced so much that the necessary number of additional RAs would be impractical. In these cases, RA cooling systems could provide a solution.

Jan 1, 2019

By A. H. Kaksonen

Numerous reactor designs for biological sulfate reduction have been reported. Fluidized-bed bioreactors (FBR) can efficiently retain biomass and allow high mass transfer and reaction rates. This work reviews the development of various sulfate-reducing FBR processes for treating acidic metal- and sulfate-containing waters and recovering metals from bioleaching liquors. The FBR process performance was evaluated with continuous flow experiments under various operational conditions: fluidization rates, influent pH values, metal, sulfate and salt concentrations, hydraulic retention times, electron and carbon sources, and temperatures. Substrate utilization and sulfide inhibition kinetics were determined with batch FBR-kinetic experiments. An artificial neural network (ANN) model was used to predict the performance of the FBR. Sulfate-reducing bacteria (SRB) were characterized in FBRs with molecular and culture-based approaches with the aim to gain a better understating of the bioprocesses. Based on the studies, FBRs are well suited for the combined removal of metals, acidity and sulfate from water.

Jan 1, 2010

By Richard B. Berg

Chlorite veins in the Silver Star district (40 km southeast of Butte) were of little interest to those who were mining gold and silver in the late 19th century. It wasn't until 1975 that unusually pure magnesian chlorite of the variety clinochlore was identified from a ?talc? claim in this district. In 1977 tests by Cyprus Industrial Minerals showed that this chlorite was suitable for use in ceramics. Mining begun in that year continues. These replacement veins of chlorite in Precambrian quartzofeldspathic gneiss differ from the metalliferous veins to the northwest in both attitude and mineralogy.

Jan 1, 1982