Search Documents

By Adrian C. Dorenfeld

The lesser developed countries (LDC's) may be classified into two categories: 1) oil producers, and 2) non-oil producers. The non-oil producing LDC's, as a class, are at present in very difficult financial straits. (1) Since the quadrupling of world market crude oil prices in 1972, an ever greater share of the LDC's export earnings have gone to pay for oil imports, in-stead of national reinvestment. The LDC's inter-national debts--much of it to pay for oil--have soared to record levels, with consequent limits for future credits. (1) Again, this inhibits future national investments, and there does not seem to be an end to the future increase of Organization of Petroleum Exporting Countries (OPEC) prices. Indeed, some of the economic difficulties in some metal markets--particularly the imbalance of production vs. markets for copper, can be traced indirectly to the OPEC cartels' heavy-handed impact on copper producing LDC's which must produce copper at any price to meet their oil bills. (2) Among the major oil importing LDC's are the Philippines and South Korea. 50th nations have substantial cement industries. The South Korean industry is geared for major export markets in the Far East. Both nations have ambitious plans for economic growth in order to accommodate burgeoning populations with ever increasing expectations for high standards of living. These plans had some success, more or less, until the high OPEC oil cartel charges had to be borne. Now, in common with all oil-deficit areas, the Philippines and South Korea are seeking lower cost sources of energy. Both countries have coal deposits. In the case of the Philippines, the reserves are in scattered, relatively small deposits. Most of the coal deposits are faulted, folded and, in general present formidable production problems for limited reserves. Nonetheless production has been on the order of about 70,000 to 150,000 tons per year in the last 30 years. Prior productions (1920-1941) varied between 9,000 Co 150,000 tons per year. (13)

Jan 1, 1978

By Charles T. Holland

INTRODUCTION Insofar as I am aware, the term rock mechanics was not in the English dictionary in 1930 when I started my graduate program at West Virginia University. Hence, I never thought that I was undertaking studies in rock mechanics when I undertook to write a thesis on the physical properties of West Virginia coal. In this case, the subject was primarily concerned with the compressive strength of coal, the elasticity of the coal, the physical weathering properties of the coal and its friability. These days investigations of rocks pertaining to such properties are included in the term "rock mechanics". Other than this aspect, the principle interest in this part of my program was that I became interested in the strength of coal from the standpoint of structural purposes, and also became cognizant of its elastic properties as well as its energy storing properties. This research also tied in with a remark that Professor Lawall made in a Mining Methods class in 1928 when he remarked that a peculiar thing was happening in the southern part of West Virginia, namely, in the Pocahontas coal field. His remarks were to the effect that pillars were blowing up in the mines and when asked why he replied the cause was not known. The failure of three-inch coal specimens, especially those in stronger coal, in non-hydraulic actuated testing machines was reminiscent of his description of those pillar bursts or bumps.

Jan 1, 1971

By Don Painter, Nico Sutmoller, Lori M. K. Kahikina, Brian Dorwart

This paper will address the feasibility of using low-density cellular concrete (LDCC) for an annular fill application where project conditions required pumping the LDCC material for distances of up to 16,000 feet. These conditions occurred during construction of the Kaneohe-Kailua Sewer Tunnel in Oahu, Hawaii, between 2014 and 2018. Located on the island of Oahu, Hawaii, this 13-foot-diameter rock tunnel extends for approximately three miles from the Kaneohe Pre-Treatment Facility to the Kailua Regional Wastewater Treatment Plant. The tunnel was built to convey wastewater and provide temporary storage for peak wet weather flows entering the collection system, thereby reducing the potential for uncontrolled discharges. LDCC was chosen for this project partly due to its environmental benefits, which were essential for an application contiguous to the inland marine and coastal waters of the Pacific Ocean. In order to ensure optimal performance characteristics—compressive strength (with a requirement of 300 psi at 56 days), flowability, and light weight—were achieved, extensive testing of various LDCC products and mix designs was completed. The testing measured the initial set time of the LDCC as well as the compressive strength needed to reduce the quantity of grout lifts required for the project.

Jun 13, 2021

By Dafydd Chandler, Milissa Hirst, Charles Hurst, Gary Snyder, Leszek Glodkowski

The Delaware County Regional Water Quality Control Authority (DELCORA) will be adding tunnel infrastructure to its wastewater conveyance system. This program involves the construction of a conveyance/storage tunnel and related facilities. The proposed 12- foot to 14-foot (±) finished diameter, TBM mined deep rock tunnel spans over 8.5 miles and lies approximately 80 ft-120 ft below the surface. The system is connected to the surface by at least five vertical online shafts and one offline shaft with associated 800ft long adit. This paper provides project details including data on the geologic conditions in which the tunnel will be constructed.

Dec 1, 2022

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By J. Payton

Public Service Company of Oklahoma began burning sub-bituminous coal in December, 1979. Initially PSO had a single source coal supply from Jacobs Ranch Mine, and in 1982 added deliveries from Clovis Point mine. Both are Powder River Basin (Wyoming) coal mines. In 1986 PSO began burning Oklahoma coal to meet Oklahoma's 10% native use law. PSO experienced random s lagging during certain blends of these coals. PSO installed a boiler performance system to help control the slagging problems from the various coal blends, to improve boiler efficiency, and increase total coal consumption.

Jan 1, 1990

By B. Birol, M. N. Saridede

"Slag density is a significant factor in determining the process efficiency of the electroslag remelting (ESR) process, where calcium fluoride (CaF2)-based slag is formed synthetically to refine metal ingots. Although there are some former studies investigating the density of CaF2-containing slags, the prediction models focusing on them are applicable only to some specific systems. The present study aims to build a model to predict density for a wide range of CaF2-containing ESR slags. To investigate density for various slag compositions, CaF2-Al2O3-based and CaF2-Al2O3-CaO-based slag compositions were prepared. Additionally, some minor constituents like FeO, MgO and MnO were added to a 5:3:2 CaF2-Al2O3-CaO slag in order to investigate the effects of these constituents on the slag. The volumes of the prepared slags were measured in a tube furnace at 1450-1550 °C using the sessile drop technique, and their densities were calculated. The results showed that for the slags, density is related to optical basicity, and therefore a prediction model based on an Arrhenius equation was built. The model was tested with data from literature, and its limitations and validity are discussed.IntroductionThe electroslag remelting (ESR) process is a refining method in which a metal ingot is remelted under a synthetic slag. These synthetic ESR slags are mainly composed of calcium fluoride (CaF2), calcium oxide (CaO) and aluminum oxide (Al2O3). Other constituents like iron oxide (FeO), magnesium oxide (MgO), manganese oxide (MnO) and chromium oxide (Cr2O3) are added to this system in relatively low amounts, according to the type of steel ingot to be refined. The prediction of slag properties, such as electrical conductivity, viscosity and density, is crucial for the selection of the synthetic slag in order to obtain the required process parameters, like temperature, the passing time of the molten metal droplet through the slag, and metal-slag separation (Akbari, Reitz and Friedrich, 2009; Hara and Ogino, 1981; Mattar, El-Faramawy and Fathy, 2002; Mehrabi, Rahimipour and Shokuhfar, 2005; Presoly, Korp and Schneider, 2008).As slag density affects metal-slag separation in the ESR process, predicting the density of an ESR slag is important for appropriate refining and improved product quality. Although there are many studies investigating the density of slags (Akbari, Reitz and Friedrich, 2009; Aune, Hayashi and Sridhar, 2005; Hara and Ogino, 1981; Matsushita, 2011; Mills and Keene, 1987, 1981; Seetharaman et al., 2013; Shu, 2007; Shu and Chou, 2013; Sikora and Zielinski, 1974; Xu et al., 2012; Zhang and Chou, 2010), the prediction models built are generally valid for oxide-containing slags (Aune, Hayashi and Sridhar, 2005; Bottinga and Weill, 1970; Mills and Keene, 1987; Seetharaman et al., 2013; Shu, 2007; Xu et al., 2012; Zhang and Chou, 2010). These models were built on either the molar volumes of the constituents (Bottinga and Weill, 1970; Mills and Keene, 1987) or the thermodynamically calculated enthalpy or free energy of mixing, which can be applied to a system containing constituents sharing an ion, such as an O- ion for oxide systems (Aune, Hayashi and Sridhar, 2005; Hillert, 1980; Persson et al., 2007). Some recent studies modeled the density of some oxide slags on their optical basicity (Shu, 2007; Shu and Chou, 2013; Xu et al., 2012; Zhang and Chou, 2010)."

Jan 1, 2016

By Xiaochao Shu, Kun Wang, Fanwei Meng, Rui Tao

Rapidly searching for carbonatite-related rare earth element (REE) mineralized systems is of paramount importance to explorers, because these systems provide the world’s most significant supply of REE. Biotite and barite are suitable indicator minerals that can offer reliable elemental geochemical information used for REE exploration. In this study, we provided an elemental geochemical dataset of biotite and barite from Cenozoic REE deposits in the eastern Tibetan Plateau, and compared the obtained data to those of biotite and barite forming in other geological settings. The F (i.e., fluorine) contents in carbonatite-hosted biotites are highly variable, with biotites from mineralized carbonatite complexes having much higher values (1.05–2.37 apfu, where apfu = atoms per formula unit) than their counterparts from barren carbonatite complexes (≤ 1 apfu). It is therefore believed that the presence of high-F biotites can be regarded as a sign for predicting REE reservoirs. Barites in REE mineralized systems contain much higher (even one or to orders of magnitude) total REE contents (ΣREE >100 μg/g) relative to those species forming in carbonate-hosted fluorite-barite deposits and open marine environments. This means that the high ΣREE concentration of barite can serve as an effective index for REE exploration. The above information is integrated into a REE exploration program in which the areas with strong local tectonism along cratonic edges are priority exploration targets, and high-F biotites and REE-rich barites can serve as direct indices for rapidly identifying carbonatiterelated REE mineralized systems at a strategic distance from other geological settings.

Jun 9, 2023

By M. J. Allan, D. J. Barratt

This paper reviews current testing methods for sizing autogenom and semiautogenom mills in the North American context with comments on the necessity for test work and requirements for different circuits and equipment selection. The economics of testing and the value received are discussed.

Jan 1, 1987

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By Gordon Kidd

Inflation and burgeoning costs are two among many factors which have generated a new surge of interest in "fringe benefits" (sometimes referred to as "supplementary remuneration" or "supplementary compensation"). Other specialized forms of compensation ("perks", in the vernacular) such as company cars, windowed offices, etc., which also are the subjects of current study, are outside the scope of this paper. For businesses, interest in fringe benefits is based on concern for employees? welfare, compliance with government requirements, and an increasingly burdensome impact on bottom lines. In 1980, according to Fred D. Lindsey in the October 1980 issue of Nation's Business, employee benefits will cost American employers an estimated $420 billion. To paraphrase Winston Churchill, "some fringes!" Indeed, few if any administrators consider employee benefits as fringes. Employee benefits impact other major areas of a company's operations as well. As listed by Beadle (1980), these areas include employee relations, collective bargaining, short-term costs, long-range funding, manpower planning, compliance with legislation, taxation for the company and for the employee, corporate image in the community, competitiveness for staff, communications, administration, claims cost containment, etc., etc.

Jan 1, 1980

By H. K. Lin

Elemental sulfur is founded to be the predominant sulfur-containing species in a leaching residue resulting from ferric chloride leaching, under given conditions, of a chalcopyrite concentrate. The mineralogical study of the leaching residue which consists of 52% elemental sulfur reveals that the sulfur formed at the end of leaching process is in the form of discrete crystal rather than coating film. Flotation has been applied to recover the sulfur successfully using xanthate as a collector. Dispersants arc needed to prevent the mechanical entrapment of silicate and quartz by sulfur. Very high recovery of sulfur with satisfactory grades can be achieved with a relatively simple notation scheme.

Jan 1, 1991

By J. P. Ulery

As a result of several recent methane/dust ignitions in surface auger and highwall mines, the U.S. Bureau of Mines investigated the occurrence of methane gas at these operations. Three mine sites were visited in western Kentucky and one in western Pennsylvania to collect run-of-mine coal samples for gas content determination using the modified-direct-method (MOM). Results indicate the samples emitted small quantities of methane, carbon dioxide, and nitrogen. Either methane or nitrogen was the predominant gas released. The same gases were released after crushing the samples for residual gas content; however, nitrogen was the primary component of this fraction. Total ~as contents ranged from less than 0.01 cm /g to 0.54 cm3/g. The hydrocarbon gases probably originated during coalification. Other gases may have originated partially as a byproduct of coalification and partially as a result of other, near-surface processes. The data suggest that although methane quantities are small, desorption could occur at near surface conditions prior to mining. The desorbed methane could accumulate as a free gas in fractures in the coal bed or roof rock. When these fractures are penetrated by the auger, methane could rapidly enter the whole atmosphere possibly creating explosive conditions.

Jan 1, 1994

By F. A. Schinner

The present study has investigated the leachability of cadmium sulfide minerals by Thiobacillus ferrooxidans and the electrochemical reactions involved in the process. Using a cyclic voltammetric technic and carbon-paste-CdS electrodes, it was found that the bio-oxidation of semiconductor cadmium sulfide minerals consisted of a number of intermediate electrochemical reactions. The overall reaction was found to be controlled by solid state diffusion as suggested by the chrono-amperometric and chrono-potentiometric measurements. The activation energy of solid state diffusion was determined by the Sand's method to be AE=24.3 kJ. A generalized mechanism was proposed for the bacterial oxidation of cadmium sulfide by T. ferrooxidan and an explanation given for the importance of high redox potential of leach solution versus the decomposition potential of the sulfide mineral. Furthermore, the effects of n-type or p-type character of CdS substrates relative to their bioleachability was discussed.

Jan 1, 1993

By H. C. Rolseth

The first step in the quarrying of granite, following removal of any overburden material, involves the freeing of large blocks from the formation. For many years the use of explosives was the accepted method of obtaining these blocks. Even today there are operations where this is considered to be the most economical method even though it does result in a high percentage of damaged stone. In more recent times the preferred procedure at most quarries has been to produce a continuous vertical cut or slot completely around the block to be separated. Originally, this was done by drilling a series of closely spaced holes around the block and breaking the web between the holes with a chisel-like tool known as a broaching bar. The machine used in this mechanical method of producing the relief slot is known as the channel bar. The modern day approach to the production of continuous channels was introduced to the industry around 1955 by the Linde Division of Union Carbide Corporation. The method employs a small rocket - jet burner producing a high temperature, high velocity exhaust flame which when directed against the granite causes it to disintegrate. This method, which has come to be known as "Jet Channeling", is now used by practically every major granite producer in the United States and Canada.

Jan 1, 1968

By C. D. Litton, I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory in Fairchance, PA, using ponderosa pine, red oak, Douglas fir, high and low volatile coals, polyvinyl chloride (PVC) and styrene butadiene rubber (SBR) conveyor belts, No. 2 diesel fuel and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters, producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (Litton et al., 1991). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters’ Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2014

By Valérie J. Bertrand, Richard W. Lawrence, Marcos G. Monroy

Two cemented paste backfill (CPB) formulations containing pyritic tailings were leached in deionized water in flooded and alternating air-flooded environments and in a simulated acid rock drainage-type (ARD) solution. Scanning Electron Microscopy (SEM), solid phase chemistry and acid-base accounting measurements documented the weathering characteristics of the CPB samples. Short-term exposures of the portland-CPB samples preferentially dissolved the cement binder to a greater extent than slag-Portland CPB mistures. In all cases, the added neutralizing potential provided to backfill by cement was short-lived and insufficient to neutralize the acid generating potential of the mixture.

Jan 1, 2000

By B. P. Faulkner

In 1974, Allis-Chalmers, in corporation with several iron ore operating companies, began to evaluate direct firing of coal in the GRATE-KILN System. Several coals were ground at the Allis-Chalmers Process Research and Test Center and shipped to Cleveland Cliff's pilot plant near Negaunee, Michigan, where they were used as fuel to pelletize Empire magnetite concentrates in the CCI pilot-scale grate kiln. Pilot plant tests were sufficiently favorable to warrant testing in a commercial-scale pelletizing plant. These tests were conducted at the Empire Mine in the late summer and fall of 1974 and again in the summer and early fall of 1975. In the fall of 1975, Allis-Chalmers Mining Systems Division started a program, in the Advanced Technology Center, designed to develop a laboratory test procedure for the evaluation and study of various parameters associated with the direct firing of coals in a GRATE-KILN System. The initial results of this program were presented at the 50th Annual Meeting Minnesota Section, AIME, January, 1977. This paper will briefly review the initial laboratory work and discuss the latest results obtained.

Jan 1, 1977

By D. Shink

A small scale continuous flotation cell was designed and constructed at Noranda Technology Centre to develop a mobile testing flotation circuit located next to the production circuit. This mobile small scale flotation pilot plant can easily and economically be set up at any circuit in a mill and used to evaluate and predict plant performance against a given flotation condition. The main feature of the cell, beside the provisions of automatic pulp level and feed rate control, is to provide a reduced surface to volume ratio approaching to that of an industrial machine. This paper describes the basic design and the results of various testwork carried out to date including aeration, conditioning, reagents, recirculation, flotation gas, etc. are presented in comparison with the plant production results.

Jan 1, 1992

By Hongling Wang, DI WU, Shuai Li, Hui Shu

Isothermal reduction experiments on carbon-bearing pellets of copper slag were investigated by the thermogravimetric method with biomass carbon as a reducing agent. The results indicated that the reduction process of copper slag‑biomass composite pellets was dominated by gas phase diffusion, and the apparent activation energy was 88.44 kJ/mol. In the temperature range from 1000 to 1200 °C, the metallization rate of pellets increased with increasing temperature, and the maximum metallization rate was 78.4%. The optimal reduction temperature of CSBCP (copper slag-biomass composite pellets) was 1200 °C.

Nov 23, 2022