Search Documents

By C. J. Burkhalter, H. Andrade, T. C. A. Gardner, J. P. Campbell

During the 1990’s several copper heap leach facilities treating crushed and agglomerated oxide and sulfide ore were constructed in South America. The majority of these facilities have been in operation for at least three years, during which time the operators have been able to monitor the performance of the heaps. The basis for the paper is a compilation of these operators’ experiences, leading to a discussion of the lessons learned over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of any inter-lift liners.

Jan 1, 2002

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide) are situated in Arkansas. Less concentrated brines (about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in Arkansas and Michigan. Arkansas, with its six plants, was the leading U.S. state in bromine production. Bromine being the leading mineral commodity valuewise produced in the state. The Michigan bromine production was a byproduct of magnesium compounds production.

Jan 1, 2006

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce risks of coal dust-fueled explosions. The goal of this NIOSH study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust (<75 µm diameter) in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity. Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing, and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle is operated at high fluid pressures to produce smaller droplets and move more air. These findings can be used to select sprays and design spray arrays to control airborne float dust over the entire longwall ventilated opening. INTRODUCTION Coal mining processes produce airborne dust that naturally deposits on the floor, roof, and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 microns in diameter, are deposited in return entries of coal mines and can be re-entrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; NIOSH, 2006). These particles are also those most likely to participate in coal dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (CFR, 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal dust-fueled explosions. Water sprays are both effective and widely accepted as a method for controlling underground coal mine dust. In fact, water sprays are considered to be the most economical and technically feasible means of reducing dust concentrations in underground coal mines (Courtney and Cheng, 1977; Barker and Humphreys, 1996). Sprays are used in several ways to control dust in mining processes: inhibiting dust formation, immobilizing dust to prevent it from becoming airborne, and capturing airborne dust (Cheng, 1973). Reductions in airborne dust concentrations have frequently been attributed to inertial impaction between water droplets and dust particles, forming larger agglomerates which then quickly precipitate out of the airstream (McPherson, 1993). Inertial impaction activity is generally accepted as the major capture mechanism for airborne particles larger than 0.5 µm in diameter. It is this mechanism that is evaluated in this study."

Jan 1, 2017

By Rick Coleman

PT Freeport Indonesia’s (PTFI) latest expansion has increased total mill throughput to 125kt/d (137,700 stpd). The most recent expansion included the installation of a semiautogenous mill (SAG) designed to treat more ore than any other single SAG mill currently operating in the world. Also included in the expansion were two large ball mills, rougher and cleaner flotation, including conventional and column cells, and a regrind circuit. All equipment is supported by a modern distributed control system. PTFI’s operations are located in the Ertsberg mining district of Irian Jaya’s Jayawijaya Mountains, the eastern-most province of the republic of Indonesia on the Island of New Guinea. PTFI, the operator, is owned by Freeport McMoRan Copper and Gold (81.3%), the government of Indonesia (9.4%) and private Indonesian investors (9.3%).

Jan 1, 1996

Partition models are commonly used to assess the separation performance of circuits incorporating density-based processes. Unfortunately, this useful tool has traditionally been overlooked by the heavy minerals sands industry due to difficulties associated with the use of toxic dense liquids. In the present study, this problem has been avoided via the development of partition models based on experimental data from microscopic grain-counts. This technique, which uses different mineral species as density tracers, provides a new tool for evaluating the multi-stage circuits that are required to successfully upgrade heavy mineral sands. The partition model approach easily identifies shortcomings of existing circuits and, when used with conjunction with linear circuit analysis, provides tremendous insight regarding the optimum arrangement of unit operations in terms of separation efficiency and plant throughput capacity. An industrial case involving the redesign of a heavy mineral sand spiral plant is presented to demonstrate the utility of these process engineering tools in plant optimization.

Jan 1, 2009

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity -clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 10, 1985

By Arman Hazrathosseini, Ali Moradi Afrapoli

Fleet management systems (FMSs) as the pivotal part of any surface mining operation find it essential to evolve from conventional into intelligent systems because of both Mining 4.0 requirements and some shortcomings inherent in conventional methods. However, this novel transformation needs to be investigated technically and strategically. To this end, the previously published research works on intelligent FMSs are explored to track the latest status of these third generation frameworks within the surface mining context. Following that, their underlying models are compared in terms of five categories of allocation and dispatching features to pinpoint the technical gaps ignored. Having drawn the future lines of research, the present article then leverages the popular SWOT analysis method to outline the strengths, weaknesses, opportunities, and threats associated with the advent of these intelligent FMSs in mines of future. By and large, the analysis indicates that advantages outweigh disadvantages. Solutions are offered to address the existing weaknesses and threats.

Nov 10, 2023

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

Invensys’ recently introduced Field Device Manager for Foxboro I/A Series distributed control systems provides the industry’s first solution that takes advantage of both the latest Enhanced Electronic Device Description Language (Enhanced EDDL) and FDT technologies. This combination provides comprehensive lifecycle support to configure, calibrate, commission, diagnose and optimize the performance of any vendors’ foundation fieldbus device. The I/A Series Field Device Manager enables users to take advantage of any EDDL, Enhanced EDDL and/or FDT host deliverables supplied by the device vendor.

Jan 1, 2007

By Daniel Maine

Swelling clay soils have been problematic to many types of infrastructure in the United States. However, their impact on underground construction is often misunderstood. The use of swell pressures in design of initial tunnel and shaft support lacks proper guidance and is often mis-interpreted. This paper provides insight and guidance on how to implement a geotechnical investigation program to determine if swelling soil exists at a site and how it impacts the design of temporary support systems for underground projects. An example is provided for how swell pressures were incorporated into the design of an initial support system for a rib and lagging tunnel system and problems that occurred.

Jun 23, 2024

By Adam Zanker

Smooth roll crushers are widely used as secondary crushers, operating most effectively when set for size reductions in a ratio between 3 or 4 to I. The feed supplied to these units varies from 13 to 102 mm in size and the product obtained ranges from 13 mm to about 20 mesh. Smooth roll crushers produce very few fines and absolutely no oversize. The diameter otfhe rolls varies with the clearance between them, feed size, and the coefficient of internal friction ofmaterial to be crushed, Detailed calculations of this relationship may be found in Unit operations of Chemical Engineering, (McCabe, W. L., and Smith, J. C., 1967, McGraw Hill, NY, Chapter 26, pg. 825). The geometrical arrangement of the roll crusher is shown on the accompanying sketch. A relatively simple relationship between the diameter of feed, the roll, and the gap between them is as follows:

Jan 6, 1980

By S. M. Moore

Each year more than 400 coal miners are injured (fatally and nonfatally) by rock falling from between or around roof supports. Many of these injuries can be prevented by the installation of roof screen. However, many coal mines are reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential savings in workers&apos; compensation (W C) premiums that can be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by Illinois and Kentucky were investigated in this study. Using data obtained from the Mine Safety and Health Administration, national and state WC bodies and individual insurance companies (e.g., average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), baseline mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state&apos;s actual WC rate-setting formulas, a sensitivity analysis was conducted to determine the total savings in WC costs after a three-year period. Annual savings in WC premiums ranged from $41,000 to $326,000 for the 67-person mine, and $96,000 to $843,000 for the 150-person mine. An economic analysis of the cost of a roof screening program at a 67-person mine was also conducted. The annual cost of a roof screening program here was estimated at $240,000. At this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

Newmont has been producing gold from the Carlin Trend for over 45 years. Naturally the focus, scale and complexity of the operations have changed considerably over this time. Newmont discovered and developed the Carlin Main ore body which is located about 32 km (20 miles) north of Carlin Nevada. The property was developed as a one mine one gold mill treatment plant operation which produced about 6,200 kg (200,000 Troy ounces) of dorè gold bars per year. The initial mine, mill and gold refining facilities were relatively small in comparison to today?s standards. The milling circuit used the Merrill-Crowe zinc precipitation process to recover dissolved gold and prepare a concentrated precious metal ?precipitate? to be melted into a dorè bar for sale.

Jan 1, 2012

By R. M. Corn

The Non-Time Critical Forest service CERCLA Action at Mansfield Canyon, Santa Cruz County, Arizona designated previous locators of unpatented mining claims as owners/operators of the Hazardous Waste Facility, retroactively liable for all reclamation costs including reclamation of mines acquired by the Forest Service. The CERCLA Action is based on non-existent tailings, a non-existent permanent resident, inaccurate and unreliable data and did not review or consider prior USGS and USBM data. The consequences of the Forest Service action include(1) reduced exploration, (2) loss of credibility, (3)public disillusionment and distrust.

Jan 1, 2000

By R. P. Killmeyer, W. W. Wen, B. K. Parekh

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen-bowl centrifuge for the dewatering and reconstitution of column -flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine clean-coal slurry from the column flotation con¬centrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free flowing granularform, while the untreated products were wet, sticky and difficult to handle. Test results indicated that the average moisture contents of the dewatered coal products were 35.7%, 35.5%, 32.6%, 29.9% and 26.5% (by weight) with Orimulsion additions of 0.0%, 0.7%, 3.2%, 4.8% and 6.4% (by weight), respectively. The handleability and dust reduction of the dewatered coal products were also vastly improved.

Jan 1, 2000

By P. Massacci

The modelling of phenomena by nonlinear dynamic Systems Theory representations require the specification and identification of suitable models of the phenomenon and the availability of good optimization algorithms to determine the optimal controls. Stochastic disturbances and difficulties of monitoring the process lead invariably, otherwise, to suboptimal performance. It will be shown that an algorithm can be formulated which will simultaneously identify and optimize such a system. The properties of the algorithm will be derived and its convergence to an optimal control proved. Some results of actual applications will be presented and it will be shown how this approach generalizes easily to optimal control of the actual processing system. These results generalize those of optimal learning and input conditioning.

Jan 1, 1991

By J. F. Brune

This paper analyzes the explosion hazard resulting from the formation of methane-air mixtures in the mined-out gobs of underground longwall coal mines. Although direct examinations of the gob atmosphere are difficult due to the inaccessibility of these gobs, evidence from methane drainage practices and investigations of numerous mine explosions suggests that explosive methane zones can form within longwall gobs. Explosions and fires resulting from these methane accumulations have led to severe and fatal injuries to the miners. Most recently, this was demonstrated in the explosion of the Upper Big Branch Mine in West Virginia, where 29 miners lost their lives.The paper also reviews current research on numerical modeling of gas flows in longwall gobs and outlines how targeted injection of nitrogen into gobs can effectively reduce the volume of such explosive methane zones. The paper concludes that comprehensive monitoring of gas compositions, along the accessible fringes of the gobs along with inertization, improved ventilation schemes and further research are necessary to control this explosion hazard and make mining operations safe.

Jan 1, 2013

By R. Adams

Zirconium is the 20th most abundant element in the Earth?s crust and it most often occurs in the form of silicate (as zircon), less often in the oxide form (as baddeleyite or caldesite). Historically, the world?s production of zircon was entirely derived from mining and processing beach sands or heavy mineral sands that were being exploited primarily for their titanium content, i.e., to generate TiO2 feedstocks that would be used for making titanium pigments and, to a lesser extent, titanium metal. Zircon was then regarded as a byproduct, with the sharply fluctuating prices typical of a commodity where the supply is essentially involuntary and not truly responsive to market demand. However, in recent years, zircon has shown considerable mining investment appeal in its own right. Projects have been planned ? and some have already come to fruition ? based mainly on the zircon potential of the deposit. Booming Chinese demand for zircon to meet the requirements of the ceramic and zirconium chemical sectors has been a major factor causing zircon prices (f.o.b. Australia) to surge from US$674/t ($611/st) at [ ] the end of 2005 to beyond US$2,400/t ($2,177/st) by the end of 2011.

Jan 1, 2012

By K. Oraee

Rate of penetration of Tunnel Boring Machines (TBM) has a significant role in the planning, measurement of productivity and performance of any tunneling project. In this paper, the application of Adaptive Neuro Fuzzy Inference System (ANFIS) in prediction of TBM penetration rate is evaluated. For this purpose, a database including Rock Quality Designation (RQD), Uni-axial Compressive Strength (UCS) of the rock, the Distance between Planes of Weakness (DPW) in the rock mass, and empirical data regarding rate of penetration of TBM from several tunneling projects are collected. The Rate of Penetration is then estimated by using ANFIS. These results are then compared with measured TBM penetration rates (actual data). It is concluded that ANFIS can be applied successfully for such purpose and result in high accuracy for prediction for the rate of penetration of TBM. The method provided in this paper can assist the mining engineer to estimate the performance of tunneling accurately.

Jan 1, 2012

By R. M. Schuster, F. M. Benavides

Samuel G. Bonasso The article by Benavides and Schuster provides an in-depth study of three transportation alternatives for a four-mine complex in western Kentucky. The examination of aerial tramways was not undertaken as an alternative solution. We feel this is an oversight since industrial ropeways are competitive with both belt conveyance and overland truck hauling. In fact, there are aerial tramway systems, operational today, which are 100 years old and operating with some original components. Maybe unfortunately, there are no fixed rules or guidelines whereby the most cost-effective means of transporting and handling material for a given situation may be selected. Each situation must be evaluated so the variables that influence the selection of the desired alternative can be clearly defined. However, there are in-place industrial ropeway systems that have proven economically feasible over a range of 1.6-50 km (1-31 miles). The more difficult the terrain, the greater the cost efficiency.

Jan 1, 1983