Search Documents

By Thomas V. Falkie, R. Venkataramani

Hand portable truck axle scales were purchased from the Martin¬Decker Company, Santa Ana, California, for weighing the rubber-tired mine shuttle cars. The scales consisted of two hydraulic load-pads, measuring 4" thick, and 21" long by 13" wide at the pad surface and one totallizer-dial indicator unit. The development of a technique to install the scales effectively for shuttle car-weighing followed an evolutionary process. The setup which finally proved to be effective entailed countersinking and level¬ling the load pads in the floor on the shuttle car trackway such that the tops of the pads were three inches below the floor level. A plat¬form consisting of two braced side-by-side 3" x 8" lumber planks was made. The platform was placed across the load pads with six inches of overlap on each side to provide room for imperfect tracking of the shuttle car. Additionally, 3" x 8" lumber planks were imbedded across the runway immediately behind and ahead of the platform. These auxili¬ary planks were firmly braced into the floor by vertical posts or jacks set against the roof; the planks constituted a stable approach platform to enable the shuttle car to roll unimpeded onto the scale platform in either direction of travel. Figure 22 shows this arrangement in detail. The setup of the scales was done during non-production hours prior to the first working shift of the week. This task took seven to twelve hours with two men. During the actual weighing experiment, the following limitations were realized. 1. Delays will be introduced into the cycle of operations because the shuttle cars must be stopped and positioned on the platform. However, these delays can be held to a minimum, time wise, as the

Jan 1, 1972

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

As the use of deep -rut mining increases, there - expected to be a greater demand for methane (CH,) measurement devices capable of scanning working faces al depths in excess of 10 m to alert mine personnel of hazardous concentrations of CH and to satisfy regulatory requirements. Remote optical devices offer the most promise to satisfy these objectives while the operator remains safely under supported roof. A second¬-generation remote Optical methanomeor (ROM) bas been designed and Is undergoing laboratory evaluation at the National Institute for Occupational Safety and Health. It operates on the principle of differential absorption of the "u;' fundamental absorption band of CH, centered at 3.31 um in the infrared region of the spectrum. The new instrument differs from the previous prototypes by the replacement of the two hand pass differential absorption technique of measurement with a single filter gas correlation technique and a refinement of the amplifier and gating circuitry used within the unit. This results in a more accurate isolation of the CH, spectral absorption band centered at 3.31 um. A specially designed 0.4m-diam variable-length gas mixing tunnel was constructed and instrumented with CH4 sampling capability to calibrate the ROM. Experiments have demonstrated the ability of the detector to respond to various conditions of CH, (pn•m) at distances as great as 12 m. Thermal radiation generated within the instrument is the controlling factor in the drift of the output signal nod, therefore the reliability of the instrument. Several approaches to reduce this extraneous radiation interfering moth the infrared detector, described, such as the installation of a fan in the instrument and thermoelectric coolers on the detector's beat sink. Implementation of this technology will significantly improve the safely of miners.

Jan 5, 1997

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A computer program has been developed to simulate evacuation of a mine in case of fire in the following, the capabilities, operations and structure of the program are described with illustrative examples to demonstrate usefulness of using the program. A detailed description of the program with sufficient information to make use of the program appears in Appendix B.

Jan 1, 1976

By BUREAU OF MINES

The approval of the U. S. Bureau of Mines when granted to a manufacturer for a gas mask is a certification that the particular device has been submitted to the Bureau of Mines for inspection and test and has been found to meet that bureau's published minimum requirements for safety , durability , and satisfactory performance . Any de- Gas masks are approved by the Bureau of Mines only as a complete unit or assembly of parts , as canister , facepiece and harness . This is in order that responsibility for rigid adherence to the bureau's requirements may be definitely located and not divided . vice marketed under this approval must be a unit composed of parts identical in detail of design , assembly , workmanship , and quality , and produced under the same control and inspection as the original device to which approval has been granted . The particular parts which comprise the approved assembly are designated in a letter to the manufacturer at the time the approval is granted . In recent years they are also specified in the approval plate authorized for use in connection with the sale of the device . Each part permitted in the assembly is legibly marked by name or number for the guidance of users of masks in ordering and identifying approved parts when making repairs , and thereby maintaining their equipment as an approved device . In view of the foregoing , any change in the design of parts or deviation from the permitted assembly of parts would violate the conditions under which approval was granted and the device would not be considered as meeting the approval requirements of the Bureau of Mines . The U. S. Bureau of Mines has been frequently requested to interpret the approval status of a gas mask assembled from parts which have separately met its requirements as components of two or more approved devices but which in the form of a complete unit has not been submitted for tests or been granted approval . Responsibility for the elements and for their proper assembly is in such case divided . Such assembled units have no status as permissible equipment under the Bureau of Mines system of schedules . The reasons underlying this policy are that the approval is granted only to some one who assumes responsibility for the whole and that the details of assembly and coordination of parts are considered to be important to the satisfactory performance and safety of the device .

Sep 1, 1932

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high- expansion foam generator. Thus allows fire-fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

By G. H. Schnakenberg

In response to the underground mining industry's growing concern with the exposure of workers to the diesel particulate matter (DPM) component of diesel exhaust, a method was developed to estimate the average workplace concentration of DPM that could be expected from using the new lower DPMemitting engines now being approved by the US Mine Safety and Health Administration (MSHA) when these new engines are equipped with state-of-the-art exhaust-control, technology for filtering and combusting DPM. The resulting estimate uses the MSHA-reported particulate index for these engines, the prevailing rule-of-thumb ventilation rate of 150 cfm/hp and the available diesel-exhaust filter technology that has been shown to be at least 80% effective in reducing tailpipe DPM. In the estimate calculation, every engine used in an underground mine is assumed to be equipped with this control technology. Under the stated reasonable conditions, an average DPM level of 90 µg/m3 (mass) is predicted as technically feasible.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D.2 Principal Types of Coating A Sodium Silicate Sodium silicate is a good fire retarder when freshly applied, but it loses its effectiveness if the relative humidity is at all high, thus exposure to a relative humidity exceeding 65 percent causes a serious decrease in the effectiveness after only one month. In fire, sodium silicate swells to a frothy mass (intumescence) which hardens and insulates the wood against heat. This property is destroyed by exposure to moisture. Manufacturers of many of the proprietary paints containing silicates state that their products have overcome this difficulty The reagent may be applied alone, or, better, in a mixture with lime-water and common salt, or with inert fillers such as kaolin or asbestos. B Ammonium Phosphate Strong solutions (25 to 35 percent) of monammonium phosphate or diammonium phosphate give good protection. Two or three coats of hot solution should be applied either with a large flat brush or an ordinary paint spray gun The solution should be applied as hot as possible, as this improved penetration, and it should be the aim of the operator to apply 4 lbs of reagent, i e , one gallon of 33 percent solution to every 100 square feet of surface

Jan 1, 1976

By K. L. Rubow

"Diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and as found in five underground coal mines- 3 utiliting diesel-powered hallage equipment and two electric-powered equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations. The first technique, using a microbrifke uniform deposit impactor CMOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of .the aerosol is predom1nately submicrometer and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance CCMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results. ,The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral ·dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 um. For the diesel equipped mines, this analysts yielded an average value for the fraction of the fine aerosol attributable to mineral dust of 1 pct. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling."

Jan 1, 1988

By R. Karl Zipf

Use of Salamon's stability criterion in underground mine design can prevent the occurrence of catastrophic domino-type pillar failure. Evaluating the criterion requires computation of the local mine stiffness and knowledge of the post failure behavior of pillars. This paper summarizes the status of the practical use of this important criterion and suggests important research to improve our capabilities. Analytical and numerical methods are used to compute the local mine stiffness. Work to date in computing local mine stiffness relies mainly on elastic continuum models. Further work might investigate local mine stiffness in a discontinuous rock mass using alternative numerical methods. Existing post failure data for coal pillars are summarized, and a simple relationship for determining the postfailure modulus and stiffness of coal pillars is proposed. Little actual postfailure data for noncoal pillars are available; however, numerical models can provide an estimate of post failure stiffness. Important factors controlling postfailure stiffness of rock pillars include the postfailure modulus of the material, end conditions, and width-to-height ratio. Studies show that the nature of the failure process after strength is exceeded can be predicted with numerical models using Salamon's stability criterion; therefore, a method exists to decrease the risk of this type of catastrophic failure. However, the general lack of good data on the postfailure behavior of actual mine pillars is a major obstacle. Additional back-analyses of failed and stable case histories in conjunction with laboratory testing and numerical modeling are essential to improve our ability to apply the stability criterion.

Jan 5, 1999

By Clarence Hall, Spencer P. Howell

The tests and studies begun by the United States Geological Survey in the fall of 1908 with a view to lessening the accidents attending the use of explosives in coal mining are being continued by the Bureau of Mines at the Pittsburgh experiment station and in the field. One hundred and six applications for the testing of 209 different explo- sives had been received at the Pittsburgh station prior to March 1, 1913, and on that date 97 explosives that had passed the required tests were on the "permissible" list issued by the bureau. This bul- letin gives the results of tests of all permissible explosives tested between May 15, 1909, and March 1, 1913. Bulletin 15 entitled "Investigations of Explosives used in Coal Mines" contains the results of tests of 17 permissible explosives tested prior to May 15, 1909. A copy of the test requirements and the names of explosives on the per- missible list dated March 1, 1913, are appended to this bulletin. An explosive is considered permissible for use in coal mines when it is similar in all respects to the sample that passed the tests required by the bureau, and when it is used in accordance with the conditions prescribed. The physical tests reported in this bulletin were conducted by Messrs. H. F. Braddock, A. J. Strane, J. W. Koster, A. S. Crossfield, A. J. Hazlewood, A. B. Coates, and J. E. Tiffany at the Pittsburgh experiment station of the bureau. The act of Congress making appropriations for sundry civil ex- penses of the Government for the fiscal year ending June 30, 1912, authorized the Secretary of the Interior to charge a fee covering the actual necessary expenses involved in making such tests by the Bureau of Mines as might be approved by him. After careful consideration had been given to the actual necessary expenses involved in the test- ing of explosives to determine their permissibility for use in coal mines, the sum of $150 was approved by the Secretary of the Interior as a reasonable charge for each complete official test. During the first year this law was in effect the fees collected amounted to more than $6,000.

Jan 1, 1913

By S. B. Flagg, J. F. Barkley

In the past few years an awakened activity in power-plant econ- omies has resulted in a marked improvement in the equipment for generating and utilizing steam. Although the improvement in design and construction of steam-driven prime movers has been greater than that of the steam-generating equipment, the economies obtained with the more efficient engines and turbines have stimulated interest and activity in eliminating unnecessary boiler and furnace losses. Much attention has been given to the boiler room in efforts to obtain proper combustion of the coal, because of the importance of the coal item in costs of power production. As evidence of this increasing interest may be cited the record of the development within the past few years of new apparatus for the analysis of flue gases. Many new forms of apparatus have appeared, including those for the determination of carbon dioxide, oxygen, and carbon monoxide, and others for indicating and for recording the content of carbon dioxide only, as carbon dioxide content is usually a good indicator for the control of furnace operation. Because of the large number of steam-power plants operated by the Federal Government and the number of CO, recorders used therein the Bureau of Mines undertook to collect information regard- ing the practical application of such recorders. Articles published from time to time concerning CO, recorders have been mostly descrip- tive, giving little reliable information as to the results that could be expected from the various types of instruments in ordinary prac- tice, and most of the tests made have been of a laboratory nature. Tests of several different types of recorders were made under service and laboratory conditions in order to obtain needed information. The purpose of the Bureau of Mines in publishing the results is to show the factors which may affect the accuracy of a CO, recorder and the manner in which a recorder should be tested. Readers should note that the remarks on different recorders apply to the instruments tested and not to later instruments of the same makers. In the course of the tests the following details were determined: 1. The lag in recording changes of composition of a flowing gas. 2. The accuracy of each type of recorder.

Jan 1, 1916

By A. B. Hooker, L. C. IlsLey

 Previous publications relating to permissible methane detectors covered investigations of the detectors from January 1922 to January 1,1937. All of these detectors are obsolete, or the designs have been modified under extensions of the original approvals. This report covers the investigations of detectors since January 1, 1937, including the present permissibility requirements as to design and performance and a brief description of each detector.

Apr 1, 1942

By Dorsey A. Lyon, Robert M. Keeney

In the inquiries and investigations that the Bureau of Mines is making with a view to increasing safety, efficiency, and economic development in the metallurgical industries, the application of elec- tricity to various processes, and especially to those in the manu- facture of iron and steel, is being given attention. Some results of the work already done are presented in this bulletin, which gives a historical review of the development of electric furnaces for making iron and steel, and discusses the problems that remain to be solved in the use of electric furnaces for the smelting of iron ores and the production of pig iron at a profit on a commercial scale.

Jan 1, 1916

By Scott Turner

The settlers of a new country necessarily suffer at first from the lack of accumulated stocks of metals - in-use that are possessed in older countries . Our American colonists were at first compelled to import their metals in manufactured forms , and it must have proved difficult to produce an exportable surplus of commodities with which to pay for them . These circumstances stimulated a search for domestic ore deposits . Various discoveries resulted , so that as early as 1628 , we find the colonists importing two craftsmen from England to establish iron -works in Massachusetts to beneficiate local ores . In 1648 , an iron -works at Lynn was producing metal at an annual rate of 400 tons . Later on , the colonial iron industries became of importance , some metal being actually exported to England . The people of this country thus early became convinced of the necessity for domestic mineral production . It is now little realized how persistent were their efforts to - make mineral discoveries , before the gold- rush to California ; the extraordinary success of our subsequent mineral explorations has overshadowed the earlier record . Precise and complete accounting of our mineral production , having the character of national bookkeeping , is available only for the series of years beginning with 1880 , when commences the official record that is provided by the Government publication called Mineral Resources of the United States . In the period of 52 years , from 1880 through 1932 , the value of mineral production of the United States amounted to more than 122 billion dollars . Only 12 billions of this total were produced in the 21 years , 1880-1900 , while nearly 110 billions were produced in the first 31 years of the present century . Of this 110 billions , over 53 billions were produced in the most recent decade , 1921- 1930 , the production of the previous decade , 1911-1920 , having been only 37 billions , though it included the war period ; that of the decade 1901-1910 was 16 billions . In 1931 , the total value of mineral products of the United States was $ 3,180,000,000 , compared with an average annual value of $ 5,556,000,000 during the previous five - year period , 1926-1930 . The decline in 1931 from that average was therefore 43 per cent . As to the three great groups of mineral commodities , metals fared worst , with a decline of 55 per cent in the value of their production , while the value of fuels declined 39 per cent , as did that of the nonmetals group .

Jan 1, 1933

This chapter explores leadership behavior in a life-threatening situation-fire in a coal mine. Previous chapters have discussed the database of interviews with miners who escaped from underground fires. Researchers raised questions such as: (1) Who led the miners out of the mine? (2) Did leadership make a difference in the escapes? (3) Was the escape leader the hierarchal leader? (4) What, if any, characteristics did the escape leaders possess? Subsequently, researchers analyzed the mine fire database from a group interaction perspective to address the leadership questions posed. Leadership has been one of the most researched topics of human behavior in the twentieth century. Studies have ranged from individual characteristics of leaders, to situational leadership, to interaction of leader and follower, suggesting different leadership techniques for different followers. The question that emerges here is: Are there different types of leadership that "fit" different kinds of situations? In a crisis situation like that examined in the present study, such information about leadership may significantly improve the chances of escape. To address these issues, the study team looked at the formal authority structure before each fire, considered leadership behavior or lack of leadership during the escapes, and examined those conditions associated with the emergence of leadership. According to Bardo [ 1978], "Emergent behaviors are those forms of action, and the norms, values and beliefs governing those actions, that rise out of the disaster situation." This chapter discusses previous studies in the area of crisis leadership and examines the emergent behaviors of leaders under duress during the mine fire escapes. Previous Studies The research on leadership during emergency situations has consisted mainly of simulation and field studies, with the principal concern being escape from building fires. During the 1980s, Hayashi [1988] created a computer simulation model to evaluate leader behavior in a fire. Although his purpose was to aid in planning for disaster prevention, his findings are relevant because they address the issue of situational leadership in crisis-where a leader changes his or her behavior to fit the situation. Essentially, his simulation model was designed to judge the actions and thinking of leaders. The simulation was tried by 101 subject/leaders 4 times each. The simulation consisted of amaze containing the leader, an informal leader, and 50 evacuees. Interestingly, the results indicated that the leader's actions were not dictated by circumstances. Any differences in behavior were attributed to the individual characteristics of each leader. The study also showed that the worse the situation became, the less individual

Jan 1, 2000

By Fred N. Kissell, Jon C. Volkwein

In This Chapter [How inert gas works to prevent methane explosions How inert gas is generated and delivered at highwall mines Volume and quality requirements for inert gas at highwall mines How an inert gas system is operated and Precautions to take during mining to prevent methane explosions] This chapter discusses a method, originally developed by Volkwein and Ulery [1993], to prevent methane explosions during highwall mining. In highwall mining, a horizontal auger or a mining machine enters the coal seam from a surface mine pit at the bottom of a highwall, and the coal is mined out from a series of parallel holes. Explosions can be prevented by injecting inert gas into each hole as it is mined. Coal near the surface has lost most of its methane gas over time. However, in recent years, surface mining has been used for deeper reserves of coal. This trend toward mining deeper reserves has increased the chance of encountering methane, and methane explosions at highwall mining operations have resulted in injuries. HOW INERT GAS WORKS TO PREVENT METHANE EXPLOSIONS A methane explosion requires the presence of sufficient amounts of both methane and oxygen, as well as an ignition source. If the methane cannot be reduced and the ignition source cannot be eliminated, then explosions may be prevented by adding an inert gas, which contains little to no oxygen, to the mixture [FWQA 1970]. Just how much inert gas must be added depends on the mining rate, as well as the composition of the inert gas. An explosibility diagram can be used to show whether a methane mixture is explosive after inert gas is added [Zabetakis et al. 1959] (Figure 10–1). This diagram indicates that gas mixtures fall into one of three range categories—explosive, explosive when mixed with air, and nonexplosive—depending on the percentage of methane and percentage of “effective inert.” Effective inert is calculated from the percentage of “excess nitrogen”3 and percentage of carbon dioxide in the mixture.

Jan 6, 2006

By S. J. Page, J. A. Organiscak

Airborne respirable dust surveys were conducted at six surface coal mines to investigate the effectiveness of dust control methods used on rotary rock drills and bulldozers. Dust controls commonly used on drills include a dry dust collection system, exhausting from a shrouded area around the collared hole, and an enclosed drill operator cab, filtering airborne dust from the cab. Bulldozers are also typically equipped with an enclosed operator cab as a dust control measure. Airborne respirable dust sampling was conducted near each equipment's source of generation and inside its enclosed cab. Silica analysis was performed on the dust samples to determine the percent silica content in the dust generated at the six mining operations. An additional eight- month follow-up of dust sampling was also conducted in the enclosed operator cabs of several rock drills and bulldozers. Data were analyzed for long-term variability of accepted control methods to abate dust and silica levels. The highwall rock drill was the major and most variable dust source as compared to the bulldozer, generating dust levels, on average, one order of magnitude higher than dust levels of the bulldozer. Four of the six drills surveyed had dust containment and capture problems at the shrouded drill table above the lple. Repairs or modifications to three of the drill dust collection systems were shown to reduce dust levels by more that 50% next to the shrouded drill table. The enclosed operator cabs provided more than 90% and more than 40% lower dust levels than at the dust source for the drill and bulldozer, respectively. Long-term sampling of several of these highwall drills and bulldozers showed that the dust levels in the drill cabs were frequently higher than 0.2 mg/m3 and more variable than in the bulldozers. The bulldozer dust levels were frequently below 0.2 mg/m). Future research should focus on improving some of the deficiencies present in the drill's primary dust collection system, and developing quality control methods to ensure the integrity of enclosed cab protection for equipment operators.

By Lloyd A. Morley, Robert Stefanko

A major difficulty encountered during the research was that nation¬al countries (almost world-wide) are in the process of revising their electrical hazard reduction standards. Their principal goal is to align their standards with the International Electrotechnical Commission (IEC) Recommendations Publication Series 79. (31-37) Additionally, CENELEC is requiring all Common Market countries to harmonize their standards. (85) However in the coal mining industry some hazard re¬duction techniques are not being accepted because some systems may not be applicable. Therefore, past literature might not directly relate a country's current feeling about explosion-proof standards. An authority in the United Kingdom (which has been a leader in hazard reduction mainly through work at the Safety in Mines Research Establishment) brought up an additional point. (15) He hopes that since revising British standards BS229 into BS4683, with the intention of corresponding with the IEC 79 series, the recent CENELEC harmoni¬zation process will also follow IEC. (8, 9, 10) The past trend in other major Common Market countries prior to CENELEC's requirement results in the authors' speculation that the standards will be pattern¬ed after the IEC Publications. (5,17,60,84,102) Several letters were sent to the East Block countries but, disa¬ppointingly, replies were dispatched only from the USSR and Poland. Recent Polish standards (1973) were received, and a very close match to the IEC Publications has been noted. (76,77) Because of their economic community, it is extremely logical to assume that the East Block stand¬ards are therefore in concurrence with the IEC. Japanese specifications also appear to be compatible with the IEC Recommendations. (42,43)

Jan 1, 1974

By J. J. Bourquin

"The Keely mine at Dagger, Indiana, is one of the few mines that is being operated successfully on a cooperative basis. This shaft mine is developing 133 acres of coal in the Indiana No. 6 bed, which here averages 5-1/2 feet thick and. lies about 110 feet below the surface. Thirty seven (37) miners and twenty (20) company men or day man are employed, and the daily output is around 300 tons. Practically the entire production is sold by contract for railroad use. No mining machines are used and all coal is produced by pick work.The mine was originally owned and operated by the Stockton Coal. Co. of Dugger, but about eight years ago it was leased to Mr. Roy Price. He sub-leased the property to ten miners, who formed an association known as the Dugger Mutual Coal and Mining Co., to work the mine cooperatively.At first many difficulties were encountered; the cooperative idea is an old one, but the practice was new to those interested. Some of the men were energetic, ambitious workers; others were inclined to let their associates produce the coal but wanted to share in the profits. In time, after a hard struggle and many changes in the personnel of the company, business-like methods were adopted and the mine was put on a paying basis."

Feb 1, 1983

By Charles Vaught, Michael J. Brnich, Henry P. Cole, John V. Haley, William J. Wiehagen

Forty-eight workers who bad escaped large underground coal-mine fires were interviewed using an open-ended protocol. This information, and the actual experiences of one eight-person mine-section crew who escaped from a Fire, were used to construct an 18-frame (page) table-top simulation exercise, which was then field tested with 134 miners. The exercise is a research toot that measures miners' proficiency in the information-gathering and decision-making skills related to escaping from a mine fire. It also helps miners to learn and practice these cognitive skills. The exercise was found to be valid and reliable. All miners reported that the exercise was authentic and would help them to remember important information. The exercise total score, and all but two item scores, significantly discriminated among miners with different levels of training. The two items that did not discriminate dealt with whether or not to abandon a helpless fellow miner. When the exercise total score data were pooled, only 13.6% of the miners achieved a desirable score of 90% mastery or greater. The simulation is important because it teaches and assesses critical judgment and derision-making skills that are rarely addressed in miner training. Index Terms- Coal mining, critical skills, decision making, emergency escape and evacuation, escape from fire judgment training, mining, safety training, simulation training, under-ground mine fires.