Search Documents

By L. C. IlsLey

The Bureau of Mines has collected field data and made laboratory investigations of trailing- cable performance in the hope of developing a better and safer cable for use with permissible mining machines . Because of their better insulation and performance , only rubber- sheathed cables were finally considered . The cables tested represented the product of six manufacturers . : After consideration of the results of the preliminary investigations , the conditions under which cables are used in mines , and the better performance of the later types of cables that were submitted as the investigation progressed , the bureau formulated a performance - test requirement and notified the cable manufacturers as follows : The hazards of the trailing cable are such that the bureau has been unable to extend beyond the machine its formal approval to cover the cable as at present developed . However , in the attempt to reduce the hazard as much as possible , cables passing certain tests will be recommended for this service and it is hoped that several cables will be developed to meet this requirement .

Sep 1, 1930

By Robert L. Chufo

The U.S. Department of Energy Pittsburgh Research Center,1 has developed and field tested a spatial, spectral sensor for measuring the thickness of mineral deposits. Knowledge of the dielectric constant of the material is not necessary because the electrical properties of the media are determined automatically along with the thickness or distance measurement. The technology was developed to measure the thickness of coal remaining in the roof and floor of a mine or the thickness of a coal pillar remaining between two mining entries for the purpose of guiding a mining machine. However, field tests have shown the new technique is equally valuable for measuring the thickness of each layer in a multilayer manmade structure such as highway paving or building foundations and the thickness of geological deposits other than coal, such as, salt, granite and sandstone. The noncontacting electromagnetic technique uses spatial modulation created by moving a simple dipole sensor antenna in a direction along each axes to be measured while the complex reflection coefficient is measured at multiple frequencies over a two-to-one bandwidth. The antenna motion imparts spatial modulation to the data and enables frequency domain signal processing to solve the problem of media, target and antenna dispersion. The technique overcomes the problem of multipath reflections from nearby metal structures and avoids the use of radio frequency absorbing material. In its present form the system measures material thickness of zero to over 3 m to within ±2.5 cm accuracy. The system parameters are variable to suit the application but for most applications default values of 40 cm antenna motion with measurements made at 401 frequencies from 0.6 to 1.4 GHz at each of 32 antenna positions with a power level of 0 dBm or less are more than adequate to provide a satisfactory signal-to noise ratio. In the range of 0 to 10 m the system operates in the continuous wave mode and by simply turning off the transmitter for ranges beyond 10 m the problems of time domain processing are entirely avoided. The technique can be implemented with a vector network analyzer, a servo controlled L-band antenna positioner, an IEEE488 bus controller and a process computer. An electronics package designed and constructed to operate in the harsh mining environment and providing 1, 2 or 3 dimensional image presentation is being evaluated as a replacement for the network analyzer. Key words: Ground penetration radar, Spatial, Spectral

The extrapolation of results from reconstructed laboratory soil columns to field conditions is difficult because of the limitations of laboratory experiments. Permeability and elution tests performed in the laboratory differed from the natural state in that the soil was sieved through 1/4 inch screen to remove large stones and roots, its density was controlled by tamping the soil into two-inch I.D. tubes instead of normal weathering, and water and latex were applied with a constant head of liquid. Tube wall effects are important in interpreting data. Conversely, interpretation of field results were confounded by non-homogeneities within the sample tested, a soil profile with gradation of permeability and density with depth, and uncontrolled weather conditions and seasonal changes that affected the results. Nevertheless, both laboratory and field tests showed that a specific latex did perform as a soil sealant. In view of these facts a soil box experiment was designed to overcome some of the disadvantages associated with the small laboratory soil columns and the field experiments. Two wood soil boxes 5 ft x 5 ft x 5 ft were built in the greenhouse at the Uniroyal Research Center. They were lined with plastic PVC sheeting provided with tubes every six inches of depth on one side of each box to measure water removal rates under saturated conditions. Tensiometer gauges were placed at depths of 6, 12, 18, 24, 36 and 48 inches and Bouyoucos blocs and resistance thermometers were positioned at 6, 24 and 48 inch depths. Each box was filled with a uniform sub-soil obtained from Ogdensburg, N. J. The texture of this soil was determined to be a sandy loam by the ASTM Hydrometer method, as shown below: [ ] The boxes were thoroughly wetted by sprinkling to abet settling and allowed to dry by draining to check seepage ports and functioning of tensiometers.

Jan 1, 1972

By O. P. Hood

The smoke problem means different things in different places . In the neighborhood of industrial plants , especially smelting plants and cement plants , the term " smoke " is applied to material discharged from these plants , consisting of a mixture of solid particles ( dust ) , fume which has condensed from vapors , and gases of various kinds that are produced in the operations . In the ordinary use of the word , however , " smoke" refers to the visible material which escapes from the burning of coal . White smoke usually owes its color to small drops of water which have condensed from the water vapor that it formed in the burning of coal . When smoke is black, the color is due to unconsumed particles of carbon and usually when the smoke problem is spoken of , it is this black smoke produced in the burning of coal that is referred to , Many inquiries in regard to smoke are addressed to the Bureau of Mines , and the following brief summary has been prepared as covering the usual questions . For references to the smoke problem in England , I am indebted to a recent interesting paper on this topic by David Brownlie .

Feb 1, 1922

Improve the strength and other properties of steel alloys. Approach Research by the U.S. Bureau of Mines indicates that steels melted and solidified under high nitrogen pressure acquire yield and tensile strengths that are up to four times the strengths of comparable stainless steel alloys without nitrogen. Fatigue strength, creep strength, and other mechanical properties are also improved. Strengthening occurs by two mechanisms: (1) increasing dissolved nitrogen in the lattice and (2) formation of dispersed metal nitride phases. Nitrogen Alloying Nitrogen alloying of a steel is generally done by introducing metal nitrides during melting of the steel. The concentration of nitrogen is limited to its equilibrium solubility at 1 atmosphere. For face-centered-cubic (fee) iron, that solubility is approximately 0.4 weight percent (wt%). For body-centered-cubic (bee) iron, solubility is 0.05 wt%. This solubility limitation can be overcome by melting the metal in a pressurized vessel. European steelmakers currently have metal-processing systems that can melt and pour tons of steel under nitrogen pressures exceeding 4 megapascals (MPa) (40 atmospheres). They have achieved nitrogen concentrations as high as 1.0 wt% in these (stainless) steels. The tensile strength is approximately twice the tensile strength of similar steels without nitrogen.

Jan 1, 1992

By Clyde E. Williams

The Northwest experiment station of the Federal Bureau of Mines , at Seattle , Wash . , was established in December , 1916 , and is one of 13 mining experiment stations maintained by Act of Congress , under the direction of the bureau , in the various sections of the country . Under the terms of the organic Act (March 3 , 1915 ) , the province and duty of these experiment stations is to cake investigations and disseminate information with a view to decreasing waste and improving the efficiency in the production , treatment , and utilization of mineral substances . The investigations carried on at the Northwest experiment station attempt to cover the needs of the mineral industry of the States of the Pacific Northwest and of the coastal regions of Alaska . The most in ortant needs of this district are for work on coal washing , electrometallurgy , and ceramics . The electrometallurgical investigations are not necessarily limited to the Problems of the Northwest , but may be of general application . Problems other than those specified above are referred to other stations of the Bureau that specialize on the particular type of investigation required . The Northwest station closely cooperates with the State of Washington through the University of Washington and with the State of Oregon through the Oregon Bureau of Mines and Geology . The University of Washington at Seattle has donated the use of an entire building , which houses the station's administrative offices and chemical laboratory , and parts of two other buildings which are usea in conducting the experimental avestigations . Twenty-five thousand dollars is expended annually by the Federal Government , while the State of Washington each biennium appropriates $ 20,000 , and the State of Oregon from time to time appropriates various amounts for the conduct of work along cooperative lines . Also , the station cooperates with private organizations tht have problems similar to those in which the station is interested . For example , the Washington Electrochemical Co. is cooperating in the electrometallurgical research, and furnishes part of the supplies and technical assistance required .

Mar 1, 1922

By L. C. IlsLey

It is most unfortunate that a few must often suffer , and perhaps die , that many may benefit from a fuller appreciation of the dangers surrounding mining operations , and the proper use of safeguards designed to offset these dangers . This has been the case during the last few months in the anthracite field , where several explosions , resulting in burnings and fatalities , were undoubtedly caused by the use of defective or improperly assembled flame safety lamps . Had this same lack of understanding regarding the proper assembly of this safety device , and had the same indifference on the part of the user in keeping the lamps locked at all times and in proper condition , been permitted in a region where the coal dust was explosive , a terrible disaster would surely have resulted . In nearly every coal -mining country , including the United States , the Davy and Clanny type of lamp has been superseded , and rightly so , by some kind of bonneted lamp . Bonneted lamps , especially of the naphtha type , while much safer than the unbonneted , have more parts and need more care in assembling . For this reason the burden of responsibility for their being properly assembled rests with the lamp man ; therefore , it is extremely important that only competent , conscientious men be given this work .

Dec 1, 1921

By C. R. Hopkins

"The petroleum refiners of the United States made rapid strides in fuel economy in 1928, when the calculated number of B. t. u. required to refine a barrel of crude petroleum was 637,000 as compared with 698,000 in 1927, a decline of 9 per cent. The major portion of this indicated increase in fuel efficiency was undoubtedly due to the gain in use of the pipe-still and the continuous process of refining as contrasted with the old batch method of distillation.,Almost without exception the new refineries are equipped with one or more pipe-stills, and many of the older plants are changing over to this type of equipment. The refineries of the Appalachian area are among the oldest and most conservative of the country, yet a number of them dismantled their old shell and cheese-box stills and installed pipe-stills in 1928.The more extensive use of the pipe-still was not the only way in which the refiners lowered their fuel requirements in 1928. The use of heat-exchangers, in which the heat from hot vapors to be condensed is used to heat the incoming cold oil, also increased in 1928, and in addition the refiners have kept abreast of the times in saving fuel through better insulation and improved burners.For the year 1928 the refiners burned as fuel the following: 46,400,000 barrels of-fuel oil; 3.362,000 short tons of coal; 114,950,000,000 cubic feet of natural gas; 77,313, 000,000 cubic feet of refinery or still gases; and 470,000 short tons of coke, in addition to a little electricity. This fuel was calculated to have produced a grand total of 582,156 billions of B. t. u., as compared with 578,784 billions B. t. u. in 1927.The total of 46,400,000 barrels of fuel oil burned represents an increase over 1927 of about 5,000,000 barrels, which made it about equal to the 1926 figure. Practically all of the refinery districts used more oil as fuel in 1928. The most important increase - over 2,000,000 barrels - occurred in the East Coast district, where greatly expanded throughput of foreign crude was instrumental in increasing fuel-oil production.The use of coal for fuel at refineries again registered a material decline, the total for 1928 of 3,362,000 short tons being 33 per cent below that of the previous year. The outstanding decrease in the use of coal in 1928 occurred in the East Coast district, where coal was probably replaced by oil. The use of coal for fuel at refineries in the States of Ohio, Pennsylvania, and West Virginia declined materially in 1928; the substitute used in the majority of cases was oil burned in pipe-stills."

Nov 1, 1929

By Dorsey A. Lyon

At the main experiment station of the U. S. Bureau of Mines , situated in Pittsburgh, Pa . , three phases of its work in behalf of the safety of the coal miner are the establishment of permissible explosives for use in gaseous and dusty mines , the development of electrical equipment that can be used with safety in mines of this character , and improvement in the safety of mechanical devices used in and about the mines . Also That these efforts are beginning to have a cumulative effect in lives. saved is evident from the fatality statistics of the industry . Although nearly 80,000 more men are employed in coal mining than ten years ago and much more coal is mined , the fatalities each year are considerably less than ten years ago . the amount of coal mined in a year for each life lost has risen between 60,000 and 70,000 tons . In 1909 , the year before the Bureau was created , the production of coal for each life lost was 174,416 tons . In 1920 , the production for each life lost was 285,000 tons .

Mar 1, 1921

By Murray Weintraub

The Bureau of Mines investigated the aerodynamic factors that control the functioning of the blowcase devices used in pneumatic processes for dispersing solids. Alumina powder of 8-micron mass-mean diameter was placed in 0.75- inch-diameter by 10-inch-long cylinders} and a blowcase technique was employed. It was determined that dimensions and gas rates for discharging the powder from the cylinder by a stream of gas may be calculated by assuming a fluidization mechanism and extrapolating residues to a desired finite quantity or to zero at the terminal velocity. The state of agglomeration of a powder at discharge may be determined from measurements of the velocity required for zero residue.

Jan 1, 1967

By J. Nielen van der Merwe

The move toward partial pillar extraction versus full pillar extraction has necessitated a new approach to underground section stability. When pillars are mined too small to support the weight of the overburden, they will, in some cases, remain stable for a considerable period; in other cases, they will collapse unexpectedly and violently. There is no discernable difference between the pillar safety factors of the failed and stable cases. The explanation lies in the characteristics of the overburden layers. A method is proposed that recognizes the overburden characteristics in the evaluation of stability. Two stability factors are calculated: one for the pillars, the other for the overburden. Using this method, it is possible to make use of the bridging capabilities of overburden layers to prevent pillar collapse. It is possible to scientifically design partial pillar extraction layouts that will be safe. Using energy considerations, it is also possible to prevent violent failure of pillars.

Jan 5, 1999

Develop and demonstrate a lightweight material that has low thermal conductivity and that would be suitable for placement using shotcrete methods. This material could be applied in deep, hot mines where mine drifts must be insulated. Its use would decrease mine refrigeration needs and reduce energy costs.

Jan 1, 1994

Improve the safety of roof bolting machine operators working in underground coal mines while maintaining or improving efficiency of the roof bolting operation. Approach The Bureau of Mines funded research under contact to develop equipment that would assure greater safety in drilling holes and installing roof bolts. The research led to the design and fabrication of a roof-boiling machine that allows its operator to per-form drilling and bolting tasks while under permanently sup-ported roof or canopy protection. How the Prototype Works The major components of the remote-control roof bolter are a flexible-shaft drill that provides continuous drilling capability without the need to Stop to add drill extensions for long holes; a roof-bolt inserter that can bend a longer-than-seam height roof bolt into the drilled hole; and a roof-bolt lifter/torquer that completes insertion of the roof bolt into the hole and torques it to the desired tension.

Jan 1, 1986

By Marc T. Filigenzi

Two of the major ground control safety issues confronting underground mine operations today are shaft pillar stability and the failure of rock around active mine openings. Failure of a mine shaft can lead to the entrapment of workers. Failure of rock around active underground mine openings can lead to roof falls, which in turn can result in worker injuries and fatalities. Finite-element analysis has proven to be a reliable method for predicting stresses and displacements around underground mine openings. However, this is a complex and time-consuming technique and is not used as often as it could be in mine planning. The purpose of this paper is to demonstrate one technique developed at the Spokane Research Center that allows the user to create a finite-element model of a two-dimensional section of an underground mine in a relatively straightforward manner. This model is then used to calculate stresses, displacements, and safety factors around mine openings. With this information, mine planers can evaluate the stability of mine openings as well as the stability of pillars and mine shafts. This analysis will help develop mining sequences and layouts that minimize stresses in that section of the mine. This, in turn, should minimize the occurrence of shaft failure, roof falls, and other hazards associated with underground mining.

To concentrate coarse mica particles using a dry beneficiation technique. Approach Concentrate coarse, II berated mica particles using a Bureau-designed system of crushers, screens, and a two-stage zigzag air classifier. How It Works Because mica has a flat plate-like crystalline structure, mica particles are significantly lighter than blocky gangue particles of the same size fraction. Thus an air classification technique can separate the flat, light mica particles from the heavier gangue particles. The ore, which Is first run through a standard jaw crusher, a roll crusher, and a hammer mill to liberate the mica, enters the rougher Zig-zag section through a rotating air lock. See photograph and diagram of a 2-stage air classifier. Airflow through the classifier can be varied according to the size of the particles being separated. The gangue material falls through the airstream of the rougher zigzag section and is discarded as tailings. The mica flakes are carried by the air-stream to the cyclone shown on the right side of the diagram, where they are collected. This rougher mica concentrate is fed to the cleaner zigzag section through another rotating air lock. The mica particles are again carried by the airstream but they are now collected In the cyclone on the left side. The cleaner concentrate leaves the left-side cyclone through a third rotating air lock and is rescreened to remove under-size material missed by the first screening. The final product of this pneumatic process is generally a high-grade mica concentrate. A generalized flow diagram for the pneumatic concentration method Is shown In the second diagram.

Jan 1, 1981

By L. C. IlsLey, R. A. Kearns

As the use of electricity becomes more and more general in mining opera- tions, interest in regulations governing its application becomes greater. During the past year the electrical section of the Bureau of Mines has made a study of State regulations now in force relating to the use of electricity in coal mines. Technical Paper 271, entitled "State Mining Laws on the Use of Electricity in and about Coal Mines", has been published as a result of this study. The present paper represents a compilation of all laws relating to accident prevention with respect to electrical circuits. This group of regulations is perhaps the most important of any that relate to safety in coal mines. Its importance is shown by reference to accident statistics in Bulletin 115, (Fay, A.H., Coal-Mine Fatalities in United States, 1870-1914, Bureau of Mines, 1916), which show that about 77 per cent of the fatalities due to electricity in and about coal mines were caused by direct or indirect contact with trolley or other power circuits. In actual number this means that of 710 men killed by electricity, 546 were killed by contact with electric wires. Undoubtedly, a large percentage of these accidents might have been prevented had the wires been properly guarded. The compilation follows:

Mar 1, 1921

By Alan H. Goode

As part of the Bureau of Mines program to broaden utilization of abundant low-quality mineral materials, the Tuscaloosa Metallurgy Research Laboratory conducted beneficiation studies on two Alabama clays. The main purpose of these studies was to develop improved plasticity and green strength in both clays and compare these improved properties with those of a typical ball clay. Whiteness of the clays was also considered. The results indicated that by adjusting the pH of the kaolin to approximately 9, a substitute for ball clay could be obtained. The investigation also showed that by a combination of attrition grinding and sodium dithionite leaching to remove iron, the underclay could be upgraded to a ball clay material.

Jan 1, 1975

By A. Dale Marcy, Pamela L. Drake

Workers who perform routine welding tasks are potentially exposed to fume that may contain manganese. Manganese may cause respiratory problems and is implicated in causing the occurrence of Parkinson-like symptoms. In this study, a field colorimetric method for extracting and measuring manganese in welding fume was developed. The method uses ultrasonic extraction with an acidic hydrogen peroxide solution to extract welding fume collected on polyvinyl chloride filters. Commercially available pre-packaged reagents are used to produce a colored solution, created by a reaction of manganese(II) with 1-(2-pyridylazo)-2-naphthol. Absorbance measurements are then made using a portable spectrophotometer. The method detection limit and limit of quantification (LOQ) were 5.2 mg filter-1 and 17 mg filter-1, respectively, with a dynamic range up to 400 mg filter-1. When the results are above the LOQ for the colorimetric method, the manganese masses are equivalent to those measured by the International Organization for Standardization Method 15202-2, which employs a strong acid digestion and analysis using inductively coupled plasma-optical emission spectrometry.

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum, The economic development of the country depended on the production and export of crude on. Output was estimated to be 49 million barrels in 1985 compared with 56 million barrels in 1984 and 47 million barrels in 1988. The country's only refinery consumed approximately 12% of the daily production of crude oil while operating at slightly over 50% capacity. The refinery output, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economic prospects were heavily dependent on the oil sector, which bad been responsible for the recent strong growth in the economy. The country consistently sought to avoid the problems associated with an overdependence on oil and followed a relatively broad-based development strategy, using oil revenues to sustain and encourage growth in other sectors. Approximately 75% of the gross domestic product (GDP) was attributed to the mineral industry in some form. GDP growth was approximately 6.5% during 1985.

Jan 1, 1987

The twelve latexes listed in Table XI penetrated A horizon soil as shown by elution through a laboratory soil column and gave good sealing efficiency. See details in Table XII. High elution through laboratory soil columns of 4 to 6 inches depth is desirable because it predicts penetration of latex to a greater depth in the field. No definite correlation was evident between penetrating ability and particle size, surface tension, or pH. Most of the materials, however, were characterized by low surface tensions in the 36 to 53 dynes/cm range while particle sizes were usually in the intermediate range of about 1500 to 2500 Å. Naugatex J-3471 (a highly crosslinked styrene-butadiene copolymer) was the most promising of this group for stability, penetrating ability; and sealant efficiency. It also showed utility with [B] profile soil. Many of the other latexes tested in this investigation showed good sealing efficiency but were judged unsatisfactory because they gave low penetration or formed surface films with & horizon top soil. In general, latexes containing cationic surfactants were not satisfactory because they formed a heavy surface film. This is due to neutralization of the positive latex charge by the negatively charged soil particles.

Jan 1, 1972