Search Documents

By M. J. Beus, M. K. Larson, J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of overcoring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 1995

Through 1986, Kentucky was the nation's largest coal producer. Currently it ranks third in production, behind Wyoming and West Virginia. Because of the size and variety of Kentucky's coal industry, virtually every kind of surface coal mining and reclamation activity takes place in the state. Extensive coal deposits occur in two separate areas: the eastern coal field, which is part of the Appalachian coal field, and the western coal field. Kentucky's reserves are estimated at 65 billion tons, with 27 billion tons in eastern Kentucky and 38 billion tons in western Kentucky. Kentucky coal is high in volatile matter, low in sulfur and ash, and relatively high in heating value. Coal from Kentucky's eastern coal fields contains a sulfur content of less than 1 percent. Conditional primacy was granted to Kentucky May 18,1982. Since then, all conditions have been removed; final regulatory approval was granted on May 30,1985. The Abandoned Mine Land Program was approved with the regulatory program May 18, 1982.

Jan 1, 1992

By Bruce K. Cantrell, Winthrop F. Watts

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989(1), which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This report reviews, available diesel exhaust aerosol and gas measurement techniques. Measurement of human exposure to toxic agents is the first step in determining the exposure-dose-response relationship. It is a fundamental step in risk assessment. Measuring exposure to diesel exhaust pollutants is particularly challenging due to the complexity and variability of exhaust components. This paper reviews current occupational health standards for diesel emissions and available diesel exhaust gas and aerosol measurement techniques. Although surveys in mines have primarily assessed diesel exhaust exposure using diesel particulate matter (DPM) some exhaust gas measurements have been used as indicators of exposure. DPM is emphasized because it is a major component of diesel exhaust, is suspected to make a major contribution to the health hazard, and is measurable. OCCUPATIONAL HEALTH STANDARDS Occupational exposure surveys of diesel exhaust frequently measure regulated pollutants, or pollutants that are suspected carcinogens, even if no permissible exposure limits (PELs) have been established. In the United States, various organizations recommend a range of allowable values for diesel exhaust gaseous constituents, including carbon monoxide (CO), carbon dioxide (CO2), sulfur dioxide (SO.), nitrogen dioxide (NO2), nitric oxide (NO), and formaldehyde (HCHO). Table I summarizes these recommended levels, showing 8-hour or 10-hour time-weighted-average values where available; where these are not available, 15-minute short-term [ ]

By D. R. Forshey

The recent occurrence of fatal accidents in copper mines, presumably due to premature ignition of loaded holes by the heat from reacting ammonium nitrate-fuel oil (AN-FO) and pyrite-bearing ores, has led to an examination of this reaction. The reactivity of prilled AN-FO mixtures with pyrite-bearing ores and the effects of water, dilute sulfuric acid, and potential inhibitors on reactivity of the mixtures were evaluated. Initiation of an exothermic reaction was observed as low as 150° F with acid in the absence of inhibitors. Low concentrations of urea, calcium carbonate, zinc oxide, and magnesium oxide were effective in inhibiting the reactivity of the mixtures. The temperatures produced during the reaction of mixtures of AN-FO and pyrite-bearing ores, in the absence of inhibitors, always exceeded the temperature at which electric blasting caps are thermally initiated.

Jan 1, 1968

By Ronald D. Hill, Elmore C. Grim

The removal of overburden often exposes pyritic materials (iron disulfide). As shown in equations 1 and 2, the oxidation of this material results in the production of ferrous iron and sulfuric acid. The reaction then proceeds to form ferric hydroxide and more acid, as shown in equations 2 and 4. [ ] Consequently a low pH water is produced (pH 2-4.5). At these pH levels, the heavy metals such as iron, manganese, copper, and zinc are more soluble and enter into the solution to further pollute the water. Water of this type supports only limited water flora, such as acid-tolerant molds and algae; it will not support fish life, destroys and corrodes metal piers, culverts, barges, etc., increases the cost of water treatment for power plants and municipal water supplies, and leaves the water unacceptable for recreational uses. The amount, and rate of acid formation, and the quality of water discharged are a function of the amount and type of pyrite in the overburden and coal, time of exposure, characteristics of the overburden, and amount of available water(l). Crystalline forms of pyritic material are less subject to weathering and oxidation than amorphic forms. Since oxidation by oxygen is the primary reaction during early acid formation, the less time pyritic material is exposed to air, the less acid is formed. Thus, a positive preventative method is to cover pyritic materials as soon as possible with earth, which serves as an oxygen barrier. In terms of mining, this step is accomplished by current reclamation techniques and small open pits.

Jan 1, 1974

By Wilbur I. Duvall

In a previous report, entitled A Gage and Recording Equipment for Measuring Dynamic Strain in Rock, a control circuit for a drum camera was described. The purpose of this control circuit was to provide a means for firing seismic caps, synchronizing the firing of the cap with the opening of the camera shutters and generating an electrical impulse at the instant of detonation. The operation of this circuit depended on the following two characteristics of seismic caps: (1) these caps contain a bridge, which breaks at the instant of detonation, and, the firing delay time of the cap is a function of the firing current. During the course of the Bureau's studies, considerable difficulty was experienced from "firing hash", i.e., spurious vibrations that appeared on the records at the time of detonation. The cause of most of this "firing hash" was traced to the intermittent grounding of the cap leads at the time of detonation. As the cap leads were still connected to the firing battery, the grounding of the leads permitted current to flow through the rock to the gage and to return to the firing battery through the shield on the gage cables. The intermittent flow of current along the cable shield produced potentials on the gage leads that were recorded as the "firing hash." To eliminate this difficulty, it is necessary to remove the firing voltage from the cap leads the instant the cap detonates. This report supplements the previous report and describes an improved circuit that can be used to fire seismic caps, remove the firing voltage from the cap leads the instant the cap fires, control the firing delay time in the cap, and generate reference signals at the time current starts flowing in the cap circuit and at the time the cap detonates. These reference signals can be used to determine the firing delay time of seismic caps and the time at which the seismic wave is generated by the explosion.

Jan 1, 1950

By W. M. Myers

The U. S. Bureau of Mines conducted an investigation to determine the cause of the deterioration of Portland cement during storage and transportation , and to discover a means of preventing it . All available printed sources of information on this subject have been examined and a bibliography has been compiled . The subject has also been discussed with the leaders in the cement industry ; the present report is the result of their cooperation , and is based principally on information thus obtained . Deterioration of Portland cement during storage over any considerable period of time has long been noted ; closely related to it is deterioration of cement during transportation, which involves not only the time factor of storage but also exposure to varied climatic conditions . Deterioration in both cases is due to hydration of the cement by absorption of moisture from a humid atmosphere , or by exposure to actual rain-fall . After hydration cement possesses no cohesive power ; the degree of deterioration is directly proportional to the degree of hydration . The amount of deterioration of Portland cement during storage has been accurately determined in an investigation by the Structural Materials Research Laboratory , in cooperation with the Portland Cement Association . Cement stored in a shed in cloth sacks retained 80 per cent of its original strength after three months storage ; 71 per cent after six months ; 61 per cent after one year ; and 40 per cent after two years . The deterioration of Portland cement during storage and transportation was noted particularly in France during the World War . Information concerning cement used by the American Expeditionary Forces was furnished by Lt. Col. H. S. Spackman and Major E. C. Eckel , U. S. R. , who had charge of practically all matters concerning cement used by the A. E. F. The cement used by the A. E. F. came from the following sources : 42,000 tons was French , Swiss , and Spanish cements ; 120,000 tons was English cement ; 55,000 tons made in plants operated by the A.E.F .; 500 tons ( Not over) from America . Deterioration was most marked in cement from the first source .

Jun 1, 1922

By George McCaa, H. C. Howarth

"During recovery operations following a recent coal-mine explosion, 12 small fires were encountered near the break line of pillar extraction in a large panel. All of the fires except one were quickly extinguished by the rescue and recovery parties. This fire had found its way into a large quantity of loose material at a corner of the cut-through between two rooms, about 100 to 150 feet from the break line of an extensive goaf; had it been necessary to seal the fire, the inclusion of this break line not only would have made the work difficult but would have made the section hazardous as it probably would have given off gas. The fire covered a floor space of about 100 square feet and when discovered was burning briskly, with the flame extending to the roof at a height of 3 or 4 feet; it was the cause of much apprehension on the part of those in charge of the recovery operations and resulted in delaying the work considerablyThe object of this article is to describe in detail the method by which the fire was brought under control and finally extinguished, so that other persons encountering similar conditions may have the benefit of the experience.When the fire was discovered a request for rock-dust, fire extinguishers, and other fire fighting equipment was telephoned to headquarters on the surface. The promptness with which fire fighting equipment and material was provided was a big factor in finally extinguishing the fire and illustrates one of the many advantages of a good organization for fire-fighting. Material was transported in mine cars to a point on the main hauling road about 1,200 feet from the fire. It was then carried to the scene of activity by workmen. The first material to be delivered at the fire was a number of fire extinguishers of various types. The contents of 30 to 35 of these were discharged on the fire and with the aid of a small quantity of rock-dust were sufficient to smother the flame temporarily. It was the opinion of several persons who were present when the fire extinguishers were used that the acid-soda type of extinguisher gave more effective results than the two or three other types used.When the contents of all of the fire extinguishers had been exhausted the fire was temporarily smothered, but as there appeared to be danger that the flame would burst forth again, means for completely extinguishing the fire were"

Feb 1, 1929

This report was limited to a search of available literature on under- ground methods to combat acid water pollution. From this review it is evident that very little work has been done in this specific area. It is also evident that there are specific areas of mining engineering and mining related hydrology and geology that need further research efforts to solve the many water problems. They are: (A) Composition, variation and availability for oxidation of sulfur in strata. (B) Rate of oxidation of sulfuritic materials. (C) In situ limestone and its influence on underground acid drainage. (D) Structural, stratigraphic and hydrologic character of old mining areas as a basis to make decisions about adjacent new mining areas. (E) Operational changes in mining methods to prevent pollution. (F) Sealants for underground coating to exclude water from contact with pyrite to inhibit formation of the contaminants. Such a program has been initiated on refuse piles. The prime purpose of this report is to investigate those practices which have been used to regulate or control water accumulation and prevent harmful mine drainage. A supplemental purpose is to indicate those areas which need further research to prevent underground mine water pollution.

Jan 1, 1970

Provide blasting-resistant, quickly reusable stoppings for large mine openings. Approach Stoppings are assembled using roof-to-bottom panels of brattice held together by Velcro seams that peel open when struck by a strong air blast. How It Works The Velcro seam is designed to open when exposed to forces lower than would normally damage the brattice. When the seams partially open, they relieve the blast air overpressure to prevent damage to the brattice panels and their anchoring devices. A stopping is returned to service by reclosing the Velcro seams. To hang a brattice panel, its top is stapled to a board, and wrapped once or twice around it. That assembly is then attached to the roof with bolts. The length of the board should be a foot less than the width of the panel to allow for the sealing seam on each side of the panel. The boards are installed end-to-end in an approximately straight line across the roof of the mine opening.

Jan 1, 1979

The Mine Safety and Health Administration (MSHA) defines an independent contractor as "any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine." Contractors that perform specific types of work are required to report the number of employees who perform work at coal mines and at noncoal mines.

Feb 1, 2005

By E. P. Youngman

The law of June 5, 1911, suplements and amends the Laws of April 21, 1810 (the basic law) and May 2, 1837. The Royal Decree of September 15, 1919, coordinates the provisions of the Law of June 5, 1911, with those of the Laws of April 21, 1810, of May 2, 1837, and of July 8, 1865, that have remained in force, as well as with certain articles of the Law of September 1, 1913, which revisad the system of taxation. The revised code has been brought together in one volume.3 All citations in this abstract refer to the coordinating Royal Decree of September 15, 1919, unless it is otherwise specifically indicated.

May 1, 1930

By C. I. Pierce

The Bureau of Mines conducted laboratory tests to determine if ultrasonic energy could reduce either the residual water or oil content of petroleum reservoir-rock samples from Appalachian area oilfields. Brine-saturated core samples were flooded with oil to residual brine saturation and subjected to 20 kilocycles per second ultrasonic energy. Then they were flooded with brine to residual oil saturation and again subjected to ultrasonic energy. Additional water displaced as a result of the application of ultrasonic energy to the flow system ranged from 0 to 4.3 percent of the original brine and averaged 1.9 percent. The increase in oil recovery as a result of the ultrasonic energy ranged from 0 to 9.0 percent of the original oil and averaged 3.1 percent. On the basis of the tests, it appears that 20-kcps acoustic waves would not have field application for oil recovery.

Jan 1, 1968

By C. B. Manula, R. L. Sanford, R. A. Rivell

A generalized flow diagram is presented in Figure 1, which shows the relationship of major model functions. This chart does not necessarily represent the anatomy of the computer program, but is designed to illustrate the informational interchange between major model functions. The related flow-charts-and computer program are listed in Parts I and II, Appendix A, respectively. Mine Car Stations The mine car stations are the activity centers for the model. The locomotive logic structure is designed to provide these stations with adequate cars and to clear them of car buildup. The model is designed to simulate a three stage haulage situation which suggests the need to differentiate station levels by type numbers. These are: a) TYPE 1 stations - mine cars are loaded here; b) TYPE 2 stations - intermediate stop and storage for mine cars; c) TYPE 3 stations - all mine cars that are stored here leave mine; and d) TYPE 4 stations - mine portal. TYPES 1, 2, and 3 have all loaded cars assigned to an ascending TYPE as their next destination. In input, if single stage haulage is designated, TYPES 1 and 3 do not exist, and if two stage haulage is called for, TYPES 2 and 3 are absent. A motor is not permitted to exchange cars between stations of the same type. Station Status Update. One major model function is to continuously evaluate the status of each mine car station. The major evaluations

Jan 1, 1974

By Oscar Lee

"Flotation is generally regarded as a process that is only applicable to metallic minerals. However, its scope is now known to be greater than this, because some of the nonmetallic minerals are floatable, such as graphite, sulphur, and fluorite. Recent observations show that limestone may be added to the list of floatable nonmetallic minerals. Such work is being done on a laboratory scale at the Southern Experiment Station (Tuscaloosa, Ala.) of the Bureau of Mines, Department of Commerce, where experimental magnetic concentration of the low-grade iron ores of the Birmingham district is in progress. Certain experiments have demonstrated that the limestone may be floated from the magnetic log-washer tailing, and then incorporated in the iron concentrate.If the loss of lime could be prevented, some ores though low in iron and high in insoluble contain enough lime to make their concentrates self-fluxing. Since this loss in the magnetic log-washer can not be avoided, the Time must be recovered from the tailing by some method and added to the magnetic iron concentrate before sintering. Then the resulting concentrate will be self-fluxing.While seeking a suitable means of treating the tailing for recovery of lime, flotation was tried. It was at once evident that this method had possibilities, during the early part of the investigation, soap solution made from a common soap was used as a flotation reagent. The froth obtained was a fairly good lime concentrate. This result was an important clue, and led to tests with the use of such reagents as oleic acid and sodium oleate. Later, cresol, creosote, coal tar and other similar flotation reagents were tested in combination with the oleic acid and soap solutions. As a result, oleic acid and cresol used together were found to be satisfactory.The tailing from the magnetic log-washer is in excellent physical condition fur flotation. The iron ore had been ground in a ball mill to 100 mesh for magnetic concentration. Hence the bond between the lime carbonate and the other constituents of the tailing was well broken."

Apr 1, 1926

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume-percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

The faculty, graduate students, and post-doctoral researchers are an integral part of the Generic Mineral Technology Center for Respirable Dust. More than fifty (50) scientists, engineers, and medical personnel are engaged in respirable dust research at five universities, The Pennsylvania State University, West Virginia University, Massachusetts Institute of Technology, University of Minnesota, and Michigan Technological University. The expertise, effort and contribution of these individuals has proven to be invaluable in the attack on respirable disease. Nationally and internationally recognized researchers in the areas of particle characterization, interaction of dust and lungs, dilution and dispersion, rock mechanics and continuing education lend their laboratory facilities, equipment and human resources to benefit the mining industry. The expertise and resources of the National Institute for Occupational Safety and Health--Division of Respirable Disease Studies is available through their relationship with West Virginia University.

Aug 31, 1989

By Thomas V. Falkie, R. Venkataramani

Underground coal winning operations can broadly be classified as conventional, continuous, and longwall mining. In conventional mining, the operations of cutting, drilling, blasting, loading and hauling, and roof support are performed in that sequence in each working face in a work area. The major difference between continuous and conventional mining is that the coal is cut and loaded by a continuous miner in the former, thereby combining the unit operations of cutting, drilling, shooting, and loading into one. Longwall applications have been viewed with great interest in recent years, and although at the end of 1970 there were only 37 longwall installations in the U. S. with combined production of less than 4 percent of underground total, there is no question about the growth potential of longwall in the United States. Increased capacity, versatility, and power characterize continuous miners today. Although continuous miners have outsold conventional gathering-arm type loading machines for some years, the latter, in the new extra-high capacity types, are continuing to find wide use. Whether the mining system is continuous or conventional, the haulage units may include six-wheel articulated shuttle cars, tractor-trailer units, or extensible belt and bridge-conveyor systems, all tending to increase the productivity of the face units. The decision as to which to choose - continuous or conventional mining - is complicated, and both systems are capable of high production rates. Most continuous miners in use today have a revolving pick-mounted drum to cut the coal and a gathering arm loading unit. Functionally, there is little difference between the loading unit in a

Sep 1, 1972

By Oliver Bowles

"The introduction into mines, quarries and manufacturing plants of machines and tools operated by compressed air has revolutionized methods of operation to an extent comparable only with that occasioned by the invention of explosives and the utilization of electricity. The use of compressed air in pneumatic tools, in rock drills, and for the operation of pumps and other machinery is well known to most miners and quarrymen, but its application as a substitute for explosives for breaking rock in a few granite quarries has received little publicity.In the region of Lithonia, a few miles from Atlanta, Georgia, is a dome of massive granite used widely for building stone and for paving blocks. The most remarkable structural feature of the granite is the absence of joints and sheeting planes. The term ""joints"" is applied to open fractures that commonly occur in rocks, usually vertical in direction or nearly so, and spaced from a few inches to several feet apart. On the Lithonia granite outcrop, however, one may walk over the bare rock surface for hundreds of feet without finding any indications of a joint, ""Sheeting planes"" are open fractures at various levels, approximately parallel with the rock surface. The presence of such planes when spaced several feet apart greatly facilitates quarrying, and where absent, as at Lithonia, the necessary fractures must be made artificially.The forcing of artificial sheeting planes is accomplished as follows: Two holes of about 3-inch diameter arc drilled close together and to a depth of about 8 feet. Two men work at these holes all summer, and sometimes part of a second summer. A very small charge of black blasting powder, not more than a spoonful, is placed in each hole, tamped with clay, and the charges are fired simultaneously with an electric battery. This starts a small fracture running outward from the bottoms of the holes. There is in most granites one direction of easy splitting known among quarrymen as the ""rift"", and as the rift direction in the Lithonia granite is horizontal the fracture follows a horizontal plane,"

Aug 1, 1920

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000