Search Documents

To test the feasibility of hydraulic borehole mining for the recovery of phosphate ore from the deep, water-saturated deposits of northeastern Florida. Approach Phosphate ore is remotely extracted through a Bureau of Mines-developed hydraulic borehole mining system. Hydraulic borehole mining can remove underground ore deposits that cannot be economically mined by the usual open pit or underground methods. It is environmentally compatible, causing none of the surface disruption or ground water pollution usually associated with other methods of mining. Selectivity of the borehole mining system also allows economical recovery of small or discontinuous ore deposits while minimizing the removal of host rock. The hydraulic borehole mining system has been used successfully in the past to mine uranium ore and oil sands. (For examples of these and other applications of borehole mining see T Technology News Nos. 97, 95, 63, 56, and 48) How it Works A 16-inch-diameter borehole is drilled from the surface down into the buried mineral deposit, and the mining tool is installed. The borehole mining tool consists of a 12-inch-diameter pipe string and accessories capped with a three-passage swivel, and ending with a mining section. The mining section has four slurry inlets and an eductor located near the bottom of the section and a single cutting nozzle located near the top. The tool generates a high velocity water jet that erodes and slurrifies the ore. The slurry is drawn through the inlet into the eductor which lifts it to the surface where it is deposited into a slurry discharge sump. All the support equipment is located and operated on the surface; only the mining tool portion of the system is underground during the recovery operation.

Jan 1, 1983

By J. Hanslovan, R. H. King

An investigation of the feasibility of shielding low-voltage trailing cables in underground coal mines is described. Both laboratory and under¬ground installation results are presented. The main objective of shielding is to reduce the electrical shock hazard; however, several problems will be encountered by mine operators who install shielded cables. Parameters related to such items as purchasing, splicing, troubleshooting, safety, and reliability are discussed. Some of these problems can be minimized by changes in cable constructions and shuttle-car reeling-device components. Both SH-C and SH-D constructions are considered.

Jan 1, 1979

Prevent collisions between large mine-haulage trucks and smaller vehicles parked in areas not visible to the haulage-truck operator, Approach Two electronic systems were developed to detect the presence of vehicles in the blind areas of a parked haulage truck. The systems can warn haulage truck operators of presence of vehicles that are blocked from view. The systems do not apply for trucks in travel. How It Works The systems use electronic transmitting techniques-one system is based on low-frequency radio waves and the other on very-high-frequency radio waves. Each system requires that a signal transmitter be mounted on the smaller vehicle to be detected. Continuous signals from this transmitter are sensed by receiving antennas mounted on the right front and rear of the large haulage truck. Upon receiving a signal, the receiver energizes warning lights and a buzzer in the cab of the haulage truck, alerting the operator to a possible collision hazard. Detection distance is adjustable, depending upon the size of the haulage truck, but a minimum of 30 feet was the design goal.

Jan 1, 1990

By Steven J. Schatzel, Joseph Cervik, Gerald L. Finfinger

Gas drainage through surface bore¬holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwal..ls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole inter¬cepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain¬age during longwall mining will be essen¬tial for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European tech¬niques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By John H. Perry

The Bureau of Mines has developed several techniques for draining methane from coalbeds in advance of mining. Drilling long horizontal holes from an underground location is one such technique, which was successfully demonstrated in the Pittsburgh and Sunnyside Coalbeds. The same technique has now been applied in the Mary Lee Coal bed at Jim Walter Resources, Inc.'s No. 4 Mine, Brookwood, Ala., where two holes were drilled horizontally--one to a depth of 1,010 feet (308 m) and the other to 540 feet (165 m). The 1,010-foot (308-m) hole proved successful in degasifying a portion of the Mary Lee Coalbed. The hole drained methane for 1 year, during which time the initial gas flow of 200,000 ft3/d (5,663 m3/d) declined to 65,000 ft3/d (1,840 m3/d). Total gas production was 40 x 106 ft3 (1.1 x 106 m3). The gas was of commercial quality, with 98 pct methane and a heat rating of 990 Btu/ft3 (36.89 Mj/m3). The methane emissions from the faces of the mine section advancing into the degasified zone were reduced by 60 pet. The 540-foot (165-m) hole was terminated prematurely when it became impossible to maintain an open hole. Because of caving, very little gas was drained through this hole.

Jan 1, 1982

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station of the Bureau of Mines have shown that satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but also upon the kind

Jan 1, 1945

By L. C. IlsLey

From time to time the Bureau of Mines has issued publications dealing with the various classes of explosion-proof mining machinery that have been tested and approved as permissible for use in mines having atmospheres that may become inflammable by reason of the inadvertent presence of gas or dust. These publications are confined almost entirely to description of the features contributing directly or indirectly to the prevention of explosion or shock hazards, and are intended to give inspectors, safety engineers, and others already familiar with the general safety requirements more detailed information on the safety features of the design of a particular machine. As a background for papers describing permissible machines and to avoid the necessity of duplicating descriptions of methods of conducting investigations and tests of such machinery, Bureau of Mines Bulletin 305, Inspection and Testing of Mine-Type Electrical Equipment for Permissibility, was pub¬lished in 1929. Three bulletins giving detailed descriptions of the three most numerous types of machines have been issued, viz., Bulletin 313, Permissible Storage-Battery Locomotive and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 392, Permissible Coal-Cutting Equipment.

Jan 1, 1937

Develop a down-hole replaceable diamond core bit that will reduce overall drilling costs and increase total available drilling time per hole. Approach A one-piece diamond core drill bit of unique geometric shape has been designed, fabricated and field tested. The bit can be withdrawn (or replaced) from the bottom of the well-bore without removing the drill rods from the hole, saving a significant amount of non-productive drilling time. How It Works The replaceable bit system consists of two basic subsystems: the removable core bit, and the equipment necessary to replace the wornout bit without pulling the drill rods out of the hole. The geometric configuration of the bit is that of a one-piece diamond studded cutting element created by "slicing off" two parallel sides of a conventional diamond cone bit. This geometric configuration, along with some minor modifications to the outer core barrel, allows the bit to be rotated in two planes and, with the retraction-insertion tools, raised or lowered through the interior of the drill rods using a conventional wire-line system. For example, to retrieve the bit, a retraction tool is lowered through the drill rods using a conventional wire-line system and at the hole bottom, the tool automatically orients itself within the outer core barrel.

Jan 1, 1981

By Martin Berman

The Bureau of Mines has investigated the mineral matter content of 38 American coals using X-ray fluorescence. Measurements of the Ka intensity for magnesium, aluminum, silicon, sulfur, calcium, and iron permit the determination of those elements as well as an indirect determination of the ash con-tent of the coals. The percentage of each of the six elements was corrected for absorption by all six elements as well as by hydrogen, carbon, nitrogen, and oxygen. It made little difference whether the values used for hydrogen, carbon, and nitrogen were obtained from chemical analysis or whether average values for all coals were used. In all cases, oxygen was obtained by difference. The correction for absorption by all these elements involved the inversion of a 6 X 6 matrix and was performed by computer. Assuming that the elements magnesium, aluminum, silicon, calcium, and iron were present in the ash as oxides, the quantity of ash was determined. The results for the mineral elements as well as for ash and oxygen were in good agreement with chemical results. Particle size was found to have a significant effect on fluorescence intensities. A study of size effects was made for pyrite particles, since the sulfur content of coals is of particular interest. Theoretical equations were derived and verified relating the intensity to particle size. It was found that the coal samples must be ground to less than 2 microns. Sulfur appears in several forms in coal, and the effect of sulfur form on intensity was investigated. It was found that the Ka intensity was independent of sulfur form but the Kß intensity varied with the type of sulfur. Thus, the Ka intensity was used for determination of the quantity of sulfur present. Utilization of the sulfur KB intensity did not permit a determination of the proportions of sulfur forms present in coal. However, for synthetic mixtures of cystine and pyrite in carbon black, measurement of sulfur Ka and Kß permit determination of each constituents from measurements of sulfur intensities alone.

Jan 1, 1968

Reduce methane levels around the shearer machine during longwall mining by directing more of the available airflow along the face and over the shearer body. Approach To address the entire mining cycle, two techniques were combined to dilute and clear the methane liberated from the face by the shearer during cutting. The first is the modified shearer clearer system, which is used during the entire face pass. This is combined with the walkway curtain which is used only during the headgate cutout. How It Works Methane ignitions are one of the most potentially serious hazards facing longwall mine operators. The high rate of coal extraction on longwall sections can liberate a significant quantity of methane during a pass. The modified shearer clearer is used to dilute methane concentrations along the entire face for both cut directions. The shearer clearer system, originally designed as a dust control technique, uses a series of water sprays located on the shearer body to direct more airflow along the face and over the shearer. (See Technology News issues, #112, #118, and #221). The only change from the original shearer clearer design is the addition of three sprays to the return-side splitter-arm/ shearer interface. The additional sprays help to ventilate the area behind the shearer body.

Jan 1, 1985

By M. K. Larson, B. G. White

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the causes and mechanisms of roof failure in underground mines. It is expected that a better understanding of these causes and mechanisms will lead to better layout and support designs that will help prevent accidents and fatalities associated with fall of ground. Two numerical experiments were conducted by NIOSH researchers using the Fast Lagrangian Analysis of Continua (FLAC) computer modeling program with a strain-softening continuum to simulate fracture zones. Two models, one of a round hole in a plate and one of a rectangular opening, were constructed and boundary conditions were applied to simulate far-field shear. The Particle Flow Code in Two Dimensions (PFC2D) computer program was used to look at the effects of far-field shear in generating fractures around an underground opening, but these models are preliminary until boundary conditions, strengths, and stiffnesses are matched to the FLAC models. Results showed that shear zones propagated from the opposite corners of openings in directions that appeared to be determined by opening shape and far-field stress. Tensile failures also formed and extended away from these shear zones. The consistent direction of shear deformation with respect to far-field shear provides a plausible explanation for preferred directions of shear as seen in geologic environments.

By E. G. King

Enthalpy increments above 298 K were determined by the Bureau of Mines for magnesium hydroxide (brucite) between 298 and 900 K by the method of drop calorimetry. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate absolute entropies, free energy functions, enthalpies of formation, Gibbs energies of formation, and equilibrium constants of formation from 298 to 900 K. By the use of published PVT data for water, a table of Gibbs energy change was given for the reaction MgO (periclase) + H2O = Mg(OH)2 (brucite) as a function of temperature and pressure.

Jan 1, 1975

Measure tattling in cemented backfill when installation of bore-hole extensometers is not feasible. Problem To evaluate the amount of load that backfill carries during pillar recovery, information about how much the backfill settles after placement is often required. However, the composition of some backfills makes them difficult to drill and the installation of borehole extensometers almost impossible. Approach Bureau researchers have developed a vertical fill extensometer that can be cast in place as a stope is being filled. It consists of a baseplate, sections of steel pipe enclosed in loosely coupled polyvinyl chloride (PVC) pipe, and a top anchor assembly that contains a displacement transducer (fig. 1).

Jan 1, 1990

By Charlie Wyche

Principal mineral products in the Dominion of Fiji were gold, silver, pit and quarry construction materials, and cement. In 1981, the combined value of these commodities accounted for about $11.6 million,2 over 85% of the total value of mineral output. Production of cement, sand and gravel, and quarry products increased substantially above the 1980 level. Mining bated on gold production was decreasing, and employment in the industry was declining. The better grade deposits in the one active mine were worked out, and only another 10 years' production at current rates was estimated to remain. While the high world gold price of 1979-80 led to intensive exploration, there has been little sum.

Jan 1, 1983

By Allen D. Look, Alan A. Sharp

"Churn drills for blast-hole drilling are important to the operation of most open-pit metal mines, but certain hazards are created through their use that cause fatal and nonfatal accidents.2/ The purpose of this circular is to present a code of safe practice prepared and followed at a large Arizona open-pit copper mine, where safety is recognized as a definite operating problem. Such a code, based upon a thorough study of available published information as well as practical experience gained from accidents and near accidents, is the result of considerable effort and monetary expenditure. It is hoped that other operations using churn drills may benefit by the code presented, either in comparison with existing rules or in the preparation of new operating instructions.The code presented is in use at the Morenci Branch of the Phelps Dodge Corn., Morenci, Ariz. Similar codes are used at the New Cornelia Branch, Ajo, Ariz., and in the waste-pit operation at the United Verde Branch, Jerome, Ariz.The authors gratefully acknowledge the cooperation of the Phelps Dodge Corp., whose personnel made: possible the collection of information included in this circular. Special acknowledgment is due Paul Simmons, safety engineer, and 3. U. Larsen, general drilling and blasting foreman, Morenci Branch, Morenci, Ariz.The importance of churn drills in Arizona mining is apparent when it is realized that at all the open-pit copper mines blast holes are drilled with this equipment. At Morenci, approximately 98 percent of the ground is broken by primary blasting of churn-drill holes.There has been a growing tendency in Arizona's copper-mining industry to change from underground to open-pit mining, with consequent increase in the use of churn-drill blast holes for primary blasting.3/Thirty-three churn drills are in use at Morenci for blast-hole drilling. The drills operate with 440-volt alternating current, and trailing drill cables, in 500-foot sections, connect with the portable drill transformer station.4/ Three Diesel-driven churn drills for drilling prospect holes also are in use. About 25 churn-drill shifts are operated currently on a three-shift basis. Ordinarily, a two-man crew is assigned to each drill; however, with prospect-drill crews a third man is added to handle the sampling.Benches are carried at a uniform height of 50 feet. Churn-drill holes are 9 or 12 inches in diameter and about 60 feet deep. The holes are 18 feet apart in hard waste and 21 feet in soft waste and ore, with toes from 11 to 13 yards at the shovel grade. Both the hole spacing and the toe have been increased gradually, until they are now 2 yards longer than in 1940. The average ground broken per hole is 3,500 tons, or 60 tons of ore per foot of hole drilled. The holes are drilled 10 feet below the bench to avoid leaving hard bottom, which requires secondary drilling and blasting.Starting with a 12-inch casing, the prospect holes average 1,200 to 1,500 feet in depth and terminate with 6-inch casing; the deepest hole drilled to date went to 1,735 feet.In addition, churn-drills are used at Morenci to drill blast holes in the silica pit, limestone quarry, and the tailings dam. Other irregular applications are the drilling of holes to set trolley roles and for concrete piling in building foundations."

Jan 1, 1950

By D. S. Kingery

The control of coal dust on coal tipples and cleaning plants has not been given the consideration that is afforded underground dust hazards. This apparent oversight is undoubtedly due to the general opinion that coal-dust accumulation in tipples or cleaning plants does not present the same type of hazard that it does underground. That this opinion is at least in part a fallacy has been proved many times, and the Bureau of Mines has on record many examples of explosions in tipples and cleaning plants.3/ In addition to this explosion hazard, coal dust is considered by sonic authorities to be injurious to the health of individuals exposed to it.4/ Obviously, it reduces visibility and contributes materially to accident hazards and the discomfort of the employees. Several companies have recognized this dust hazard and the advantages derived from controlling it; consequently, they have installed equipment to allay and control the dust on, their cleaning plants and tipples. The object of this paper is to. Summarize briefly some of the methods new in effect.

Jan 1, 1943

[ ]

Jan 1, 2012

By G. W. Jones, R. E. Kennedy

A simple , quick, and relatively accurate device is needed for determining the presence of very small concentrations of organic halide gases in various atmospheres . Such a device would enable safety engineers , health officials , and others to discover quickly the presence of these gases in a suspected atmosphere and thus be able to apply protective measures promptly. This detector should prove useful in detecting leakage of halide gases from refrigerating and air - conditioning systems and in determining the presence of halide solvents in the atmosphere of dry - cleaning and degreasing establishments where organic halide solvents are used . Virtually all poison war gases are halide compounds . Because of the high toxicity of these gases , even in very low concentrations , a detector having the proper sensitivity should be useful in civilian defense for determining when atmospheres are relatively free of poison gases .

Apr 1, 1943

Assist in controlling or extinguishing fires that occur in abandoned mine lands (AML) by providing a compilation of information on past fire control projects, the estimated extent of the current problem, and factors affecting the occurrence, propagation, and extinguishment of AML tires. Conventional fire control methods and their probable effectiveness are evaluated. Background Fires that occur in abandoned coal mines, waste banks, and coal outcrops constitute a serious health, safety, and environmental hazard from toxic fumes, deterioration of air quality, and subsidence. Although fires on AML occur in every coal-producing State, the severity of the problem varies, with most underground fires occurring in Kentucky, Pennsylvania, and Wyoming. Surface fires are prevalent in Kentucky, Pennsylvania, and West Virginia. Methods to extinguish or control AML fires, including excavation, fire barriers, and scaling, are generally expensive and have a relatively low probability of success (see figures 1 and 2). Bureau of Mines Study The Bureau compiled information from a variety of sources and found that the problem of AML fires is a serious one. Such fires can involve a high degree of hazard and can be difficult and costly to control. AML fires usually involve smoldering combustion in outcrops, waste banks, or abandoned mines. Given the nature of these fires, it is unlikely that the extent of the problem or the cost of solutions will decrease in the near future.

Jan 1, 1992

By Roy C. Bartholomae

An accurate characterization of the vibration environment and a vibration qualification test derived from it will be a very useful tool for manufacturers of instrumentation for use on underground coal mining equipment. Recognizing this, the Bureau of Mines sponsored a study wherein vibration levels were measured on mining equipment to form a basis for developing the required vibration test. The data base was composed of 160 samples taken at different positions on a variety of underground machinery. The data were analyzed and presented in a format typical of military vibration qualification tests. The form was shown to be virtually identical to the swept sine test envelope specified in MIL-STD-810B for tracked vehicles.

Jan 1, 1982