Search Documents

By D. S. Kingery

The data obtained from this study cover test areas that are gassy to ultragassy and pillared areas of different sizes and degrees of tightness. The methods of controlling ventilation, applying bleeders, and supporting bleeder entries varied in the different test areas. It was not possible to study all conditions likely to be encountered in coal mines. Undoubtedly, there are areas where bleeder entries, even though properly planned and maintained, might prove unsatisfactory. However, on the basis of this study, the following observations were made: 1. Tests showed that each bleeder system studied provided some movement of air through the pillared area; the quantities of air delivered to the pillar line, ranged from 23 to 82 percent, depending mainly on the extent to which bleeder re-turns were used as main returns from the section. 2. Pressure measurements taken across pillared areas showed maximum pressure drops ranging from 0.05 inch of water for a shallow gob to 2.69 inches for a very deep gob. The pressure differentials varied with the size and tightness of the gob but proved adequate to induce airflow across worked-out areas or through fringes of the gob to the bleeder return system.

Jan 1, 1957

By D. E. Wolfson

Destructive distillation (carbonization) was shown to be a feasible method of disposing of scrap tires. The Bureau of Mines conducted tests under a variety of conditions. Solid, liquid, and gaseous products were produced, recovered, and analyzed. The quantities of the various products were shown to be quite dependent on the test temperature. Variability in composition of the liquid and gaseous products with changes in test temperature was also significant.

Jan 1, 1969

By Charles L. Kimbell

While the statistical summary focuses on 1991 data, this update and outlook section draws on information available to the author as of the date of final preparation in early 1993. For all the press notoriety associated with the shift in the Near East crisis from the defensive posture of Desert Shield to the restoration of Kuwaiti sovereignty through Desert Storm, this was not the dominant event governing global economic thinking in 1991 and the first half and more of 1992. From the global perspective, the momentous political changes in the area that was the U.S.S.R. and in the smaller emerging transitional economy states of Eastern Europe will have even greater current and long-lasting effects on world mineral industry activities than the crisis in the Near East.

Jan 1, 1993

By Joseph A. DeCarlo

This publication presents a tabulation of oven-and beehive-coke plants in the United States as well as pertinent statistical data on the number, capacity, kind, and condition of the ovens. Coke is an essential raw material in pig-iron production and the coal-chemical materials produced during the coking process are used to manufacture fertilizers, paints, plastics, synthetic rubber, explosives, detergents, nylon, pharmaceuticals; dyes, and many other products necessary to the high standard of living in this country. In table 1 the oven-coke plants in the United States on December 31, 1959, are listed. This shows the name and address of the company, location of the plant, classification or type of ownership, number and type of ovens, annual coke capacity, and the coal-chemical materials produced. The "furnace" plants I are those owned by iron and steel companies and most of them are integrated with blast furnaces to facilitate transportation of raw materials for steel making. Furnace plants represented 87 percent of the total coking capacity and their average annual capacity was 1. 3 million tons. The "merchant" plants are those associated with chemical companies, gas utilities, as well as those that produce metallurgical, industrial, and residential-heating grades of coke and coal-chemical materials for sale on the open market. These coke plants are smaller than furnace plants and in 1959 their average coke capacity was only 520 thousand tons annually. On December 3l, 1959, there were 54 furnace and 20 merchant oven-coke plants in existence in the United States.

Jan 1, 1960

By Stephen R. Wilson

This paper is one of a series published by the Bureau of Mines on the mineral resources of the Nation. It describes briefly the occurrence of sodium sulfate in Salt Lake and Tooele Counties, Utah, presents data on sampling, and describes ex-traction and refining raw material and a mining research project that has been conducted on the deposits. ACKNOWLEDGEMENTS Acknowledgments are given to the Tintic Standard Mining Co., Salt Lake City, Utah, and Bartlett Chemicals, Inc., New Orleans, La., for permission to use data obtained by the companies. The authors also acknowledge the courtesy of J. A. Marsh and H. K. Thurber, geologists and mining engineers, for permission to use information in reports prepared by them.

Jan 1, 1957

By R. V. Ramani, V. T. Burgos, J. A. McClay

Introduction The Cost program was developed to provide the planning engineer with a tool to evaluate the cost implications of the technical mine design decisions. Direct costing methods are employed, where feasible, to provide greater detail and accuracy in the primary cost centers. Options have been provided in the cost computation, economic analysis, and output data subsystems to increase the flexibility of the system. Computer Program The program is written in Fortran IV for use in the IBM System 360/370 computers. i. Main - The main routine reads and stores input data from three sources, user input, Cost Data Library, and data transfer from the Master Design Simulator. Data is trans¬ferred to the appropriate subroutines, as they are called, by means of labeled common blocks. ii. Subroutine CSTCOM - is a data modification routine which computes the peripheral charges related to labor and supervisory costs. iii. Subroutine MANPWR - interrogates section data to determine the total labor and supervisory costs for each cost center. iv. Subroutine CAPCST - computes the total capital investment for each cost center, including the economic life and salvage value of each element. Capital costs are determined by user selection of quantities and models of equipment. Equipment costs are stored in the Cost Data Library for retriev-

Jan 1, 1975

By W. D. Bryson

This paper is one of a series being prepared by the United States Bureau of Mines on tunnel-driving methods. The practices described are those used at No. 11 mine of the Colony Coal Co., Denver, Colo. No. 11 Mine is situated at Dines, some 14 miles north of Rook Springs, in Sweetwater County, Wyo. It is served by a spur off the Winton branch of the Union Pacific Railroad. The Colony Coal Co.'s mines were opened in 1918, and since that time have been among the largest producers of coal for the railroad and domestic markets in the Rock Springs coal district.

Jan 1, 1932

By T. T. Campbell

This report describes the development of new electroplating baths from which tin-nickel alloy plate was deposited. Although tin-nickel plate can be deposited from an aqueous ammonium bifluoride bath, the corrosive nature of this bath has served as a deterrent to its use. The Bureau of Mines felt that more general acceptance of this new alloy plate would follow if neutral or alkaline baths could be developed. Promising results were obtained from electrolytes containing both tin and nickel chlorides dissolved in triethanolamine-hydrochloric acid or in ethylene glycol hydrochloric acid baths. Current efficiencies close to 100 percent were obtained with these baths. Research revealed that tin-nickel plate could be produced from organic solvents or from mixed aqueous-organic electrolytes. The composition of the alloy deposit - 65 percent tin and 35 percent nickel - was found to exhibit the same single-phase structure that is obtained from the commercially accepted fluoride-type bath.

Jan 1, 1959

By D. H. Baker

This report, one of a series prepared by the Federal Bureau of Mines on the technology of titanium, describes the development of an electrorefining cell from which cathode deposits up to 30 inches long can be produced. Data show individual deposits to be homogeneous, comparable from top to bottom, and not varied in quantity or quality of metal over the entire length of the deposit. Investigations concerned with various diameter cathodes showed that cathode current efficiencies were materially reduced with cathodes less than 2 inches in diameter. Deposits produced on 1/2-inch-diameter cathodes showed cathode current efficiencies of 19 percent and on 1-inch cathodes, just over 22 percent, whereas deposits produced on 2- and 4-inch-diameter cathodes showed about 70-percent current efficiencies. A series of 20 deposits on 4-inch-diameter cathodes was produced under simulated production operation. The average current efficiency, based upon a divalent ion, was 72 percent with 11 1/2 pounds of metal produced per cycle of operation - 98.8 percent of which had a Brinell hardness number (B.h.n.) of 80 or less.

Jan 1, 1959

By Edward F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged scrubbers with high dust collection efficiency for use in under-ground coal mines. The Bureau's Pittsburgh (Pa.) Research Center has developed and assisted in the development of several types of improved scrubbers that are especially suitable for various underground mining applications. Research efforts concentrated on reducing the size, power, and water consumption of these scrubbers, while optimizing their dust collection efficiency. Fractional dust collection efficiency, air volumetric range, size, power, water consumption, and application guidelines for each type are described. Air pressure differentials ranged between 2-and 3D-inches water column (wc). The dust collection efficiency of six scrubbers--a venturi, two flooded-fibrous-bed, a venturi-impaction plate, a wetted-fan, and a rotating flooded-bed--were compared. The rotating flooded-fibrous-bed and the stationary flooded-fibrous-bed scrubbers showed the highest coal dust collection efficiency. Test results show that these scrubbers can generally achieve respirable size coal dust collection efficiencies in the high 90-pct range required to reduce both long-(8-hour) and short-term coal mine dust concentrations below Federal requirements.

Jan 1, 1979

By Edward L. McHugh, Jami M. Girard

While less than 1% of reported accidents are associated with slope stability problems, slope failures were responsible for about 15% of all U.S. surface mine fatalities between 1995 and 2001. Small rockfalls, which may involve hand-sized rocks weighing only a few kilograms, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic meters of material or more can be fatal even for heavy equipment operators. As part of an ongoing study at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, several remote-sensing technologies are being evaluated as tools to monitor slopes for hazards and to assess slope stability. Field tests of a hyper spectral imager were conducted to assess its value for improving geologic maps of potentially unstable alteration zones on mine slopes. An interferometric radar device capable of detecting very small displacements on slopes awaits final assembly and field testing. Computerized monitoring methods using images from digital and video cameras are being assessed for application to mine slope surveillance. These and other techniques will eventually provide new tools to augment current methods for monitoring ground control hazards in mines.

By J. M. Stuve

Provisional values for the heat of formation of europium trichloride and europium sesquioxide were determined by solution calorimetry utilizing europium metal of more than 99-percent purity. The resulting values for the heats of formation of Eu203 (cubic) and EuCls (hexagonal) were -386,970 ±l,200 cal/mole and -218,740 ±650 cal/mole, respectively, measured at 298.15° K.

Jan 1, 1965

By John J. Henn

An evaluation is presented for an ammonium sulfate leaching process designed to extract manganese from Cuyuna, Minn., and Aroostook, Maine, deposits. In this process the manganese and iron in the ore are reduced to MnO and Fe 3 0 4 in a shaft furnace; the reduced ore is then leached with ammonium sulfate solution forming soluble manganous sulfate while leaving most of the iron undissolved. After filtration, the manganese and some impurities are precipitated from solution as carbonates which are then pelletized and calcined to form a product composed mainly of Mn3O4. The plants are designed to produce 100 tons per day of manganese contained in a product that is suitable for the production of ferromanganese. A byproduct credit, together with the extra processing cost, is included for the Cuyuna ore processing plants because Fe2O3 may be recovered for use in blast furnaces. The estimated operating costs per ton of manganese, excluding income taxes and return on investment, are: [ ] The process with or without byproduct recovery, when treating Cuyuna or Aroostook ores, is not economically competitive with ores available at $71.43 per ton of contained manganese.

Jan 1, 1968

By M. D. Marshall

This handbook is for the engineer or person responsible for the storage and removal of material from bins and silos in the minerals industry. The objective of the handbook is to prevent bin-related accidents by eliminating problems which require workers to enter bins. It provides basic information on handling materials so that knowledgeable decisions can be made on bin design and accessories to minimize flow stoppages. Materials are classified in terms of their flowability, and bin design and accessories suggested for each classification. A method for classifying a material is also given, and the various types of material flow aids reviewed. Safety around bins is the basic theme of the handbook. Federal regulations are reviewed and additional suggestions presented to prevent bin accidents. New equipment for releasing material hang-ups is reviewed.

Jan 1, 1984

By James H. Scott

A technique of seismic refraction data analysis has been developed in which a digital computer is used to generate a two-dimensional model representing a layered-earth depth interpretation. Travel times are picked on seismic records by the human interpreter. These times, together with shot point and geophone locations and refraction layer control information, are submitted to the computer on punched cards. A first approximation delineation of each refraction horizon is obtained by a computer adaptation of the delay-time method. The approximation is then tested and improved by the computer through the use of a ray-tracing procedure in which ray travel times computed for the model are compared against field-measured travel times. The model is subsequently adjusted in an iterative manner so as to minimize the discrepancy between computed and measured travel times. The Fortran program is listed in the appendix of the report together with instructions for preparing data cards and examples of results.

Jan 1, 1972

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United States and publishes economic data on the industry, based upon reports from producers. This publication lists all producers that reported commercial production to the Bureau for 1959. The companies named herein represent virtually all commercial producers of peat. A few companies, however, may not have been canvassed or failed to respond, as tine survey is voluntary For producers, arid the industry has many small operations that operate intermittently. No consideration was given to the quantities of peat produced and output of the various companies listed ranged from less than 100 tons to more than 50,000 tons, Peat is included in the Bureau's annual surveys of the mineral industries because, technically, peat is a fuel. Although none is used for fuel in the United States, peat is a potential source of energy and one of our large mineral resources. The domestic peat industry produces peat chiefly for use as a soil amendment. The industry has expanded rapidly during the past decade with active operations increasing from 45 in 1947-49 4/ to 105 in 1959. Output during this period has increased 218 percent, rising from 131,782 net tons to 419,460 net tons.

Jan 1, 1960

By Fun-Den Wang

A two-dimensional plane strain analysis by the stiffness matrix method was used to analyze two basic pit slope configurations. The magnitudes and the directions of stresses are given for a V-shape and for a flat-bottom pit with the slope angle varying from 30° to 90° at 10° intervals, Stress effects due to irregular pit configuration or to in-situ forces are discussed. Equations of similitude for gravity loading are given. Expressions are also given for the stresses at the toe as a function of slope angle. Procedures are given for finding the stresses in any geometrically similar pit slope of different dimensions and material properties from the stresses and equations presented in this report. Numerical results show that the V-shape pit slopes have lower stresses than the flat-bottom pit slopes; hence, they are inferred to be more stable.

Jan 1, 1970

By William C. McBee

Prompted by forecasts of a sulfur oversupply, the Bureau of Mines, U.S. Department of the Interior, is conducting research on potentially large-scale uses of this commodity to extend or replace such construction materials as asphalt, cement, and mineral aggregates. Through these efforts, paving materials have been developed in which sulfur replaces up to 50 pct of the asphalt normally present and which can be prepared and placed with existing mixing and paving equipment. Laboratory properties and design methods for this direct mixing process are described along with properties obtained on small-and large-scale field demonstration projects. These properties are compared with those obtained from control materials prepared without sulfur additions. Monitoring for toxic gases during laboratory and commercial mixing and paving operations is discussed also.

Jan 1, 1978

By Deborah A. Kramer

As part of the Nation's growing concern with the competitiveness of U.S. firms in the world economy, especially with respect to advanced materials, the Bureau of Mines assessed the actual and potential recovery and manufacturing capabilities for gallium and gallium arsenide (Gacis). GaAs has advanced from a laboratory curiosity to a material with important "high-tech applications within only the last few years, and although protected North American gallium supplies are currently considered adequate, consumption could grow to the point that this assessment would need reevaluation.

Jan 1, 1988

By H. Schultz

Urban refuse that was mechanically separated at the U S Bureau of Mines pilot plant in College Park, Md., was successfully evaluated for its fuel values using standard coal analysis methods. Analyses performed on refuse samples taken from five sample points included moisture, ash, sulfur, chlorine, and heating value. It was recommended that characterization of the combustible portion of urban refuse by standard coal analysis procedures should be widely adopted.

Jan 1, 1975