Search Documents

By C. A. Allen

"The problem of signaling to the hoisting engineer from a moving cage in the shaft has been considered by many mine operators for a number of years. There are several methods in use in different mining districts, and so far as the writer is aware they have been further developed in Utah than in any other state. The latest installations are of interest because they use a very low-voltage circuit for the shaft wires and also because the wiring can be so arranged that the hoist can be stopped from the cage, if so desired.The first installation in Utah was in the shaft of the Centennial-Eureka mine under the management of C. E. Allen. It was placed in operation in the summer of 1899, end has been in continuous and satisfactory operation for 21 years. The arrangement consists or two bare wires down the shaft carrying a current at 60 volts potential, with a device on the cage for making connection between the two wires. This device is simply a short piece of wire which is thoroughly insulated from the cage and is operated by a short lever. Whenever the cage rider wishes to signal the engineer he pulls down the lever, forcing the short wire out against the two bare wires, thus making a circuit which rings the bell in the hoist-room. A similar device was planned in the Grand Central shaft at Mammoth, Utah, but was later abandoned. The cause of failure was reported to be that the shaft was very wet."

Jun 1, 1920

By Maria I. De Rosa

Table 37 and figure 13 show the number of fires and fire injuries for surface stone mines by state during 1990-2001. Table 37 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 96 fires occurred in 31 states and 1 fire occurred in Puerto Rico. Sixty-eight of the fires caused 67 injuries and 1 fatality (including 6 fires and 5 injuries involving contractors). The yearly average was eight fires and 5.6 injuries. The Ewhr value was 689 x 106 hr (Irr = 0.02), and the LWD value was 7,399. Indiana had the most fires (eight fires and four injuries), followed by Georgia (seven fires and seven injuries) and Pennsylvania (seven fires and five injuries). Of these states, Georgia had the highest injury risk rate value (Irr = 0.058). Table 38, partly illustrated in figure 14, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries show an increase during the second period followed by a decrease during most of the remaining periods. Employees' working hours increased during most of the periods. The In values follow patterns similar to those shown by the injury values. Tables 39-44 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 15 shows the major variables related to fires for 1990-2001. Table 45 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By C. W. Davis

"A copper-palladium-gold-silver ore is being mined at Salt Chuck, Prince of Wales Island, Alaska, from which a concentrate is produced that contains 40 to 50 per cent copper, and considerable amounts of palladium, gold and silver. There has been much difficulty in obtaining assays for palladium, gold and silver from the mine, smelter, sampler, and umpire that check within reasonable limits. While the results for copper content have not been unusual, the results for palladium have varied as much as 0c8 oz. on 3 oz. material, results for gold differed by 0.1 oz. on 1.6 oz. materials, and for a silver content of 7 oz., results differed by as much as 4.0 oz.The Bureau of Mines was requested to determine the causes of variation in the results of the different assayers, and to develop a satisfactory procedure for analyzing such ore.Three samples of concentrate were received for analysis, two small lots that had previously been assayed by the various laboratories, and one large sample. The large sample was dried and ground in a ball mill, put through a 150-mesh screen, and then returned to the ball mill for thorough mixing. The small samples were ground to pass a 150-mesh screen and then mixed on a mixing wheel.The large sample (No. 1) was analyzed by five different procedures, one of the small samples (No.2) by three procedures, and the other (No. 3) by two procedures (the two small samples being too small for further tests). The different procedures tried and the results obtained arc presented below. The samples of concentrate were from ore mimed and milled by the Alaska palladium Co. at Salt Chuck."

Feb 1, 1926

By Ralph L. Brown

As a preliminary step in a recent study4 of the phenols present in a low-temperature tar, the writers prepared the hydroxyacetic derivatives of the simpler available members of the phenol series in order to obtain material to assist in fixing the identity of similar derivatives obtained from the phenols of the tar. When comparing the melting points of the pure derivatives we had made with those given in the literature we were unable to find the characteristics of one of the xylenol derivatives which we had prepared--namely the 1, 3 dimethyl-2-phenoxyacetic acid, In the belief that the compound does not appear in the literature we are presenting these notes on its preparation and its melting point. The hydroxyacetic derivatives are easily prepared and in good yield, and are useful in studying mixtures of phenols. The 1, 3 dimethyl-2-phenoxyacetic acid makes the fifth of the six isomeric derivatives to be reported in the literature. Gluud and Breuer report the preparation of the 1, 3, 4, the 1, 4, 2, and the 1, 2, 4 derivatives. A fourth isomer-¬the symmentrical 1, 3, 5--has been reported by Schutz6, although no record of it occurs in the indexes. The remaining derivative--the 1, 2, 8-has not, been found and it is now being synthesized in the Organic Chemistry Laboratory of the. Pittsburgh Experiment Station. It is true, however, that from a phenolic fraction boiling 215.9 to 2180 isolated from natural petroleum, Tanaka and Kobayashi7 obtained a hydroxyacetic derivative melting at 103.3°. They state that this is the 1, 2, dime ethyl-3-phenoxyacetic acid but present no evidence for the assertion. The known derivatives are summarized in Table 1 following;

Jan 1, 1929

By Fred N. Kissell

A parachute-type stopping intended for changing the course of mine ventilation air during mine emergencies has been designed and tested. Some production uses are also visualized for metal mines. Preliminary tests in the laboratory and underground indicate that the parachute stopping is a workable concept, but further developmental research is required.

Jan 1, 1975

By Carlton E. Brown, William P. Yant

"INTRODUCTION Direct visual microscopic determination of particle-size distribution and number concentration of atmospheric dust is time-consuming and trying to the eyes. By using the microscope to project images of the particles at high magnification onto a screen much of the eyestrain can be eliminated and particle-size distribution results obtained with less effort and at a considerable saving in time. It also permits simultaneous observation of the images by more than one person. Microprojection requires no more skill and very little more apparatus than is required in the use of the microscope. Anyone familiar with the microscope should be able to obtain as perfect images on the projection screen as in direct visual microscopy since the same laws and limitationsThe theory and practice of microprojection are described in detail in texts. 5/6/ The procedure has been used and found to be satisfactory for measuring the particle-size distribution of sub-sieve-size substances, such as pigments and powder 7/8/ in the same size range as that of atmospheric dust. The Bureau of Mines has used the microprojector and found it to be quite satisfactory for (1) the determination of the number concentration of atmospheric dust R.I. 3289 in samples collected by the Owens jet dust counter; (2) particle-size distribution in samples of atmospheric dust collected by the Owens jet dust counter and by the electric precipitator; and (3) the particle-size distribution of dusts, blood cells, bacteria, and pollen. Work is in progress at this Bureau on the use of the microprojector in counting impinger samples. The use of different kinds of illumination, such as reflected (dark field), polarized, monochromatic, and ultraviolet, in the projection of images of atmospheric dust particles is being considered."

Oct 1, 1935

By M. E. Tyrrell

Magnesia spinel (MgO.Al203) recovered from dusting slags in the system MgO.Al203-2Ca0.SiO2 is in the form of single crystals most of which will pass 35-mash. This investigation was undertaken by the Bureau of Mines to evaluate the concentrates as a refractory raw material. Three specific types of refractory bricks were studied: (1) dense, (2) lightweight bubble, and (3) insulating. Test specimens ware fabricated 1 by dry pressing, fired to 1,675° C., and tested by procedures common to the industry. The concentrates produced a refractor, having satisfactory density and mechanical strength; however, spinal is sensitive to thermal shock and the possibility of producing a spall-resistant brick using aggregate of such small grain-size must be considered remote. Lightweight refractorias fabricated of spinel bubbles were the most promising of the types tested. They were 30 percent lighter in sight than the dense refractory, their mechanical strength was good, and definite superiority in thermal shock resistance was indicated.

Jan 1, 1962

By John D. Bardill

This report covers the magnetic survey in the Redford-Clayburg area , which was part of a general survey of magnetite deposits in New York started in 1943 . Other areas being surveyed include the Star Lake district , St. Lawrence County; Russia Station district , Clinton County; Brewster district , Putnam County; and the Sterling district , Orange County. Only a relatively small portion of the area was covered by reconnaissance and detailed surveys . Results were promising enough to warrant additional work. Magnetic surveys of this type serve as a basis for selecting areas for diamond drilling by the Bureau of lines .

Jan 1, 1947

By Alice V. Peter

Meerschaum or sepiolite is employed principally in tobacco pipes and cigar and cigarette holders, although a few other uses of minor importance are Down. The unique value of a meerschaum pipe is derived from the owner's pleasure in watching the color deepen with smoking and in having the color "set" at the desired shade. The name "meerschaum" (German for "sea foam") is applied because the material, when pure and dry, will float on water. Owing to its resemblance to the porous, bonelike structure of the cuttlefish, or septa, it is also known as sepiolite. There are a few scattered deposits of meerschaum in. the United States which have yielded a small product ion, but the world's supply of the' material is obtained fined principally from Asia Minor, Meerschaum deposits near Eski-Shehir, Turkey, are said to have been worked 2,000 years ago, but commercial exploitation is a development of the last hundred years DESCRIPTION AND PROPERTIES Meerschaum is a hydrous magnesium silicate (H4Mg2Si3010) having the following theoretical analysis: Si02, 60.8 percent; MgO, 27.1 percent; H20, 12.1 percent. It is a soft. (H.2 - 2.5), fine-grained, earthy, white, gray, or yellow material. It is very light weight when pure (specific gravity, 1 to 2) and is highly absorbent. Because of its porosity the proportion of water present in the mineral is affected by the humidity'of the atmosphere. In a moist atmosphere the water content may be as much as 21.7 percent. Then wet the material is soft and somewhat plastic. When dried again it becomes lard and tough. The toughness is especially apparent in some forms that have a fibrous or leathery texture.

Jan 1, 1934

By Harry G. Dosh

Sillimanite, kyanite, and andalusite are aluminum silicates having the same chemical composition (Al2SiO5) and are used in the ceramics industry for the manufacture of high-grade refractories. Natural sillimanite with added corundum or other alumina to just short of mullite (3Al2O3 -2SiO2) proportions is unequalled for jobs wherein strength at high temperatures, resistance to spalling, and resistance to slagging by acid slags are desired. High-grade porcelain ware also requires these minerals. At the same cost, sillimanite would be preferred for most uses, but the lack of any large source of sillimanite bas given economic preference to kyanite or andalusite for special refractories and high-grade porcelain wares. Sillimanite-bearing schists were observed in Spartanburg County, S. C.; as early as 1937 by D. Hoye Eargle, geologist with the U. S. Soil Conservation Service. The mineral was not identified until 1942, when Miss Jewell Glass, of the U. S. Geological Survey, examined several of the deposits. This identification was confirmed in 1943 by Dr. Laurence L. Smith, of the University of South Carolina, when he examined the Spartanburg County deposits and found numerous additional occurrences of sillimanite schist in Greenville County. Subsequent work by the Bureau of Mines and the South Carolina Geological Survey has been responsible for the location of additional sillimanite-rich schist deposits in Spartanburg County. Between October 1, 1948, and November 21, 1948, the Bureau of Mines conducted an exploratory diamond-drilling project on the John Gideon property in the southeastern section of Spartanburg County (fig. 1) and drilled a total of 681.7 feet in six holes. Drilling indicated that the deposit is relatively shallow, as no ore was cut below the zone of weathering.

Jan 1, 1950

By C. A. Alien

The increasing activity in oil shale has had a tendency to direct the attention of the industry to any substance from which gasoline or other oils can be secured . Cannel coal for many years has been known, as a source of oil and formerly it was the only substance from which kerosene was obtained . The name of coal oil was given to kerosene because it was derived from cannel coal before any flowing wells were brought in in the United States . In an isolated region in Southern Utah there is an unusually thick and clean bed of cannel coal which laboratory experiments indicate can be made to yield about seventy gallons of oil to the ton . This coal was first described in Bulletin 341 of the United States Geological Survey under the title of Colob coal field . This field lies at the western and southern base of the Colcb plateau and extends from the town of Cedar City southward to Kanarra and then southeastward to the town of Mount Carmel . Cedar City is 35 miles south of east from Lund on the Los Angeles and Salt Lake Railroad which is the nearest railroad point . Mount Carmel is about 90 miles south of Marysvale , on the Denver and Rio Grande Railroad , which is the nearest railroad point from the eastern end of the field . The Colob coal occurs in Lower Cretaceous rocks and a number of wagon mines have been opened on the seam in the vicinity of Cedar City , Kanarra , and Mt. Carmel , but between these places the field has been very little prospected . The cannel coal , so far as known at present , is limited to a small area on the head waters of the north fork of the Virgin River in Township 39 and 40 South , Range 9 East . In this region it occurs as a bed 5-1 /2 feet thick over which lies a layer of bituminous coal 2 feet and 5 inches thick .

Feb 1, 1921

By L. C. IlsLey

So many subjects are covered in State mine-safety regulations that any attempt to compare different State laws in their entirety would be futile. On the other hand, if one selects a single phase or branch of safety work, such a comparison may prove profitable. The subject selected for study in this paper is limited to legislation or regulations dealing specifically with safeguarding (electric) motored equipment used in gassy mines. T When one reads glowing accounts of the safety activities being carried on here and there it is easy to believe that everything which is right and proper is being done to safeguard the mine.workers; but, when one takes time to look into the weakness of many State regulations, it is evident that there is still room for improvement. Undoubtedly it would have been much better for the safety of mines if electrical equipment had been introduced into mines 50 years earlier. If electricity had been in general use when the first mine regulations were pre- pared, those formulating the rules would have covered this hazard along with other hazards, but as electricity came in at a later period, safe mine legisla- tion regarding it has been woefully neglected. Today the United States in general is far behind most other coal-producing nations in the provision of adequate safety rules or laws for the installation and maintenance of electrical equipment and wiring. Returning to the subject of our study, approximately 30 of the 48 States mine coal. More than 20 of these States' produce coal in large quantities. How- ever, of the 30 States only four, 3 Pennsylvania, Utah, Washington, and West Virginia, have laws which specially call for the use of explosion-proof types

Jan 1, 1929

By Donald R. Corson

The Bureau of Mines is conducting research on the effects of various established and potential soil-stabilization additives to hydraulic backfill. This initial phase is an evaluation of the effect of inclusion of varying amounts of Portland cement and combinations of cement and a dispersant on the bearing strength of backfill. Results of unconfined compression tests are given for over 200 sample cylinders incorporating a fill material with cement or cement and dispersant. Inclusion of a minor amount of dispersant (0.2 percent by weight) is found to yield a significant increase in strength for 20-to-1 and leaner sand-cement mixes. An apparent optimum concentration of dispersant exists beyond which no further increase in strength is achieved. A dispersant-cement ratio of l.8- to-1 yielded a strength increase of 515 percent over the strength of untreated 40-to-l sand-cement mixes.

Jan 1, 1966

By R. A. Beall

Homogeneous zirconium-alloy ingots have been cast on a production basis by the consumable-electrode arc-melting process at the Northwest Electrodevelopment Experiment Station, Bureau of Mines, Albany, Oreg. This paper describes the various methods used to introduce alloying materials into the ingot and evaluates 1 each method by the degree of homogeneity of resulting ingots, as determined in tests on sections cut from the ingots. As many as 30 or more ingots, each 6 to 10 inches in diameter and weighing 300 to 500 pounds, were melted, using each method; and, as most of them subsequently were fabricated to strip 0.1 inch thick, the test results are considered to be representative of production practice. Ingot homogeneity has been considered more difficult to achieve in arc-melting practice than by methods where the molten metal is poured into molds and the addition can be stirred into the total mass of metal before casting. Owing to the unique requirements of consumable-electrode arc melting the addition can be made only to that part of the total mass of the ingot that is molten at one time. Observation of the flowlines in 500-pound ingots produced at Albany indicates that the molten pool has a maximum depth about equal to the ingot diameter. The weight of metal molten at one time is, therefore, not over 100 pounds. Characteristically, the arc-melting process is conducive to segregation, which can be overcome, at least partly, by adding the alloy constituents almost continuously during casting.

Jan 1, 1956

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

BIBLIOGRAPHY 1. Dougherty, John J. , "Control of Mine Fires", Publication of the Mining Extension Service, School of Mines, Appalachian Center, West Virginia University (1969). 2. Coal Age, "Fire, Explosions and Recovery, Federal No. 1 Mine", November, 1963. 3. Nagy, et al., "Sealing a Coal Mine Passage through a -Nor-ii-hole: A Progress Report", U.S. B. M. Publication No. 6453, (1964). 4. Murphy, et al., "Use of Fly Ash for Remote Filling of Underground Cavities and Passageways", U.S. B. M. Publication No. 7214, (1968). 5. Pennsylvania Drilling Company, Pittsburgh, Pennsylvania. Personal Review of Equipment. 6. Industrial Hazards and Communication, Division of U. S. B. M. Personal Communication with John Murphy and Merle Bowser. 7. Instrument Technology, Inc., Borescopes and CCTV Systems for Inspections of Nuclear Reactors; Personal Communication. 8. "Public Works", July, 1972. 9. The Industrial Hazards and Communications Division of the U.S. B. M. , Personal Communication regarding Cohu Model No. 2006. 10. "Bibliography on Underwater Photography and Photogrammetry", Eastman Kodak Pamphlet No. P-124. 11. Optical Properties and Visual Effects of Smoke-Stack Plumes, U.S. Department of HEW, 1967. 12. Middleton, W. E. K. , "Vision Thru the Atmosphere", Univ. of Toronto Press, 1952. 13. Kodak "High Speed Infra Red" film and Singer Corporation Model TI Silicon Vidicon TV Camera. 14. Night Vision Laboratory, Fort Belvoir, Maryland; Barnes Engineering Company, Stamford, Connecticut, Model, T-101; AGA Inc. , Secaucus, New Jersey, Model, "Thermovision" 680.

Jan 1, 1973

By Isaac A. Zlochower

This paper presents data on the limiting (minimum) oxygen concentration (LOC), in the presence of added N2, of methane (CH4), propane (C3H8), ethylene (C2H4), carbon monoxide (CO), and hydrogen (H2), and some of their binary mixtures. It also addresses the issue of the flammable concentration (flammability) limits of these pure gases in air. The study is based on spark ignited explosions in large, spherical laboratory vessels (120-L and 20-L) using a 7% pressure-rise criterion for explosion propagation. The results of the study are compared with the older values which used long flammability tubes with a diameter >5 cm together with visual evidence of substantial upward propagation. They are also compared to results reported recently using a 12-L spherical flask with a visual flame propagation criterion. Finally, they are compared to results reported in Europe using more modest flammability criteria and smaller chambers. The findings reported here show excellent agreement between the 120-L and 12-L results, good agreement with the 20-L results, and reasonable agreement with the earlier flammability tube values for the lower flammability limits. They disagree, however, with the more conservative European values. These results and those from the 12-L experiments also feature lower LOCs than are given by traditional flammability tubes. A model for the LOCs of such fuel mixtures based on the Le Chatelier mixture rule for lower flammable limits is seen to reasonably fit the observed results on binary mixtures and can accommodate more complex mixtures as well. One such set of ternary mixtures containing CH4 and 1:1 CO:H2 is well fitted by the model.

Jan 1, 2009

1.1 Bituminous-Coal and Lignite Dust. - Carboniferous material having a volatile ratio of 12 percent or more by weight and a fineness such that the material passes through a No. 20 sieve. 1.2 Active Underground Workings. - Underground places in which men are required to be or to pass through in the performance of normal mining operations for the production of coal. 1.3 Working Areas. - Underground areas where bituminous coal and lignite are mined, specifically: (a) Face. - The solid surface of the unbroken portion of the coalbed at the advancing end of the working place. (b) Face Area. - The working area inby the last open crosscut in an entry or a room, including the pillar being extracted or longwall being mined. (c) Room. - A place abutting an entry or airway where coal has been mined and extending from the entry or airway to a face. (d) Crosscut (Breakthrough). - Passageways or openings cut through a pillar to connect adjacent entries or rooms. 1.4 Entry. - Underground haulageways, travelways, and airways, except working areas as defined in section 1.3. (a) Active Entry. - An entry in which coal is being mined from a portion thereof or from connected sections. (b) Parallel Entry. - Usually an intake airway parallel to the haulageway. (c) Back Entry. - Usually a return airway parallel to the haulageway.

Jan 1, 1960

Develop and evaluate a mechanical position and heading system (MPHS) that provides information about underground mining machine position and heading to aid in the remote positioning of mining machines during face maneuvers. Background While great improvements have been made in mineworker safety, progressive technology continues to create a safer, better working environment for miners by keeping them away from the dangerous face area. In maintaining such high standards of safety, the Bureau is investigating remote, computer-assisted operation of mining systems for underground, highwall, and surface mining applications. A key component of computer-assisted operation is a guidance system. Since there are no guidance systems on any commercial continuous mining machines, the Bureau itself developed and tested the mechanical position and heading system (MPHS). The MPHS is based on linear position transducers (LPT's), and operates on principles of triangulation to provide machine position (xy coordinate), and orientation in the xy plane (yaw or heading). These data are needed in order to keep the continuous mining machine in proper alignment before and during the cutting cycle. The MPHS theory development is in three parts: characterize the sensors used and their configuration; select and define the navigation reference frames; and derive a closed-form solution for determining the position and beading from sensor information. Application of the MPHS theory required the development of hardware, software, and system interfaces.

Jan 1, 1992

By T. J. McDonald

The methods used and the results obtained in the application of high-expansion foam on a recent fire in an operating mine in western Pennsylvania were reviewed. This is the first instance where foam has been applied extensively to a fire under actual mining conditions although considerable research has been conducted and experimental fires have been controlled. The Bureau of Mines began investigating the foam-plug technique in 1957 in its experimental coal mine, following reports of successful trials in Eng-land, where the basic methods, using the normal ventilating current, were developed. Early in the research it was apparent that the normal ventilating current in mines in the United States would not provide adequate air pressure to drive a foam plug the distance that might be required. Subsequently, the Bureau of Mines developed a portable high-expansion foam generating unit consisting of a fan having relatively high pressure potential, net, sprays, and metering equipment. To date, foam generators have been constructed by the Bureau, by at least one operating coal company, and by one manufacturer of safety equipment. A number of units from the latter supplier have been adopted by coal-mining companies as an integral part in their firefighting installations.

Jan 1, 1961

By C. J. Johnson, C. J. Bise

"As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity.Room-and-pillar mining accounts for approximately 68% of the nations underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-mid-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.IntroductionThe ultimate goal for any coal mining company is to effectively use its human and financial resources to maximize its profits through the extraction of its reserves. Although recent workforce reductions in the industry have resulted in a more efficient use of labor and increased productivity, there comes a point in time when further reductions in the numbers of workers in each operating section are impossible with existing equipment. For example, Farinelli and Bise (1987) found that labor cost constituted 62% - 73% of the cost per ton of coal at the mining section, with a minimum crew size. Thereafter, efforts to increase productivity must focus on more efficient mine plans and technology.The fact that an increase in productivity can be realized by reducing non-productive time (change-out and tram time) and converting it to productive time has been known and demonstrated for quite some time. What has not been demonstrated frequently is the quantification of the potential productivity increase of currently emerging technology or ""add-on"" equipment. It is one thing to be able to say that a piece of equipment will make an operation more productive, but it is another thing to be able to quantify the productivity increase that will justify the purchase of the new equipment. Not only is a financial benefit possible in room-and-pillar mining with an increase in productivity, but a decrease in the time necessary to develop a longwall panel can also occur.The purpose of this paper is an analyze the impacts of a changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to several scenarios incorporating emerging technology. To do this, four cases will be developed. A base case, consisting of the typical manner in which continuous-miner sections are currently operating, is compared to three layouts incorporating: (1) flooded-bed scrubbers on radio remote-controlled continuous miners, (2)a continuous miner with side-mounted roofbolters, and (3) a continuous miner with side-mounted roofbolters used in conjunction with a continuous-haulage system."

Jan 1, 1989