Search Documents

By Marvin L. Whisman

A radiotracer technique developed by the Bureau of Mines extends to the parts-per-billion range the sensitivity for determining contributors of deposits formed in stored and thermally stressed jet fuels. The method depends upon measuring radioactivity associated with thermally induced deposits from fuels containing one labeled compound. The technique was applied to 88 test blends, representing 12 fuels and nine carbon-l4 labeled fuel constituents or fuel additives, or both. Data from results of these tests are included in this report. With this radiotracer technique, the contribution of fuel components and additives to thermally induced deposits in a variety of fuel environments was estimated before and after storage.

Jan 1, 1969

This Part is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a corner. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency which propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1974

Provide reliable, early-warning fire detection instruments, telemetry, and control systems for noncoal underground mines. Approach Industrial-grade fire detection instruments and signal telemetry equipment were modified for long-term exposure to harsh underground mine conditions, then were installed in four mines to evaluate long-term performance and reliability. How It Works The elapsed time between the onset of a fire and its detection is critical because fires tend to grow in size and intensity with time. Early fire detection and warning permit the initiation of a mine's emergency plan (evacuation, fire fighting, etc.) while the fire is still small, or ideally, while it is still in the incipient stage. Fire detection and warning systems, utilizing sensitive heat, flame, smoke, and gas analyzers, provide the most rapid and reliable indication of a developing fire.

Jan 1, 1987

By L. Garner McDonald

The U.S. Bureau of Mines tangentially impacted potential coal-cutter bit shank materials against sandstone to investigate the potential of the materials to ignite natural gas by a friction-generated hot streak. The shank material samples were mounted in a 24-in, 550-lb flywheel, which was rotated at surface speeds of 400 to 900 sfpm. The sandstone was advanced toward the rotating flywheel at feed rates of 1 mil per impact. The atmosphere mixture was 7 vol pet natural gas in air. Three grades of polycarbonate resin, an ultra-high-molecular weight polyethylene, and a zinc alloy (ZA27) were among the potential materials. None of these materials caused ignition of the methane at any of the three test speeds (400, 600, and 900 sfpm), but the above materials do not have sufficient strength to hold a carbide tip during coal cutting. Of the materials having sufficient strength to hold a carbide tip, three nickel-based alloys proved less likely to cause a natural gas ignition than did iron-based alloys such as 4340 (a commonly used shank material for coal cutters).

Jan 1, 1992

By G. L. Oldright, John D. Sullivan

"The present article is the second of a series of papers dealing with the dissolution of copper minerals in various reagents. Work done on the problem has been carried out at the Southwest Experiment Station of the United States Bureau of Mines, in cooperation with the Department of Mining and Metallurgy, University of Arizona. The first paper4 dealt with the dissolution of azurite, malachite, chrysocolla, and tenorite. Preceding articles5 have also dealt with other factors involved in the leaching of copper ores.Cuprite (Cu20) is usually considered as a mineral which is not adaptable to sulphuric acid leaching. Hofman,6 in describing leaching by sulphuric acid, states: ""Cuprite is decomposed into CuO and Cu; and ore carrying cuprite has to be oxidized (weathering, roasting) before treatment."" Greenawalt7 says: ""When acted upon by dilute sulphuric acid, it is partly reduced to metallic copper and partly oxidized into copper sulphate. When heated with strong acid it is entirely oxidized to sulphate."" Work to be described in this article was undertaken to ascertain the conditions whereby all the copper in cuprite could be converted into the soluble sulphate."

Dec 1, 1929

By J. A. Zimrner, R. J. Tirnko

The roles of main mine fans in underground mines are to induce airflow and continuously re- move hazardous gases and dust. While most larger mines use multiple fans to accomplish these tasks, many smaller mines employ only a single fan. This paper concentrates on those mines having only one fan to provide ventilation needs. If this fan should cease to function, it is likely that methane concentrations will in- crease in some areas of the mine. As a safety precaution, Federal Regulations require that personnel must be- gin evacuating the mine within fifteen minutes after fan stoppage. Powered haulage can be used to transport workers to the mine portal as long as travel is through areas where hazardous levels of methane are not expected. To determine where methane will accumulate along haulageways during a fan stoppage, air samples must be taken at specific areas and analyzed for hazardous gases. During this study, procedures were developed for measuring methane levels along the haulegeways that are used to exit a mine following stoppage of the main mine fan. Methane levels were measured in four different mines at selected underground locations during four planned fan stoppages. In these mines the measurements taken only at the specified locations showed that, if workers had used electrically powered haulage to exit the mine following a fan stoppage, the methane accumulated along haulageways during fan stoppages would not have significantly increased the risk of an ignition.

Develop computer software that can aid in improving the visibility and illumination in underground mines by providing quick analysis of existing equipment and conditions and the effects of potential modifications. Background Poor visibility and illumination are common problems in underground mining. Mining equipment often restricts operators' fields of vision. Also, fighting systems are often positioned where they cause excessive glare, which restricts the visibility around the machines even further. To help address these problems, the U.S. Bureau of Mines (USBM) has developed a PC-based software package to analyze certain human engineering aspects (ergonomics) of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines. Approach The Crewstation Analysis Programs (CAP) package includes assessments of visibility, illumination, and glare in the surrounding work area. The advantage of using computers for these types of analyses is that numerous design iterations can be tested quickly and efficiently to determine the effects of changes on visibility. This cuts down the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where testing would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design could be tested while the machine remained in service.

Jan 1, 1993

By George S. Scott

The Bureau of Mines conducted ignition, flammability, and decomposition experiments on gas mixtures containing ethylene to determine its flammability characteristics at elevated pressures and ambient temperatures. Pure ethylene was found to propagate a decomposition reaction at 1,000 psig and ambient temperatures when ignited with 1 gram or more of guncotton in a 2-inch-id bomb. The decomposition products were primarily carbon, methane, and hydrogen.

Jan 1, 1965

By E. P. Youngman

The mining laws referred to by those who furnished the reports mentioned in the preceding paragraph are : General Austrian Mining Law of 1854 and the Law of 1868 , which prescribes for Hungary (as well as for Transylvania ) the full text and decisions of the General Austrian Mining Law; Government Decree 18346 , 1859 ; Parliamentary Decree of 1861 ; the Law of 1871 ; the Commercial Code , Law 37 of 1875 ; the Industrial Lar of 1884 ; the Law of 1386 ; the Decree of the High Court of Justice , 5540 , of 1399 ; Laws 6 and 7 of 1911 ; Law of 1921 ; Laws 23 and 24 of 1922 ; Laws 5 and 21 of 1927 ; and Law 40 of 1928. ( Lev 21 of 1927 and Law 40 of 1928 are labor laws . ) A compilation of the mining laws of Hungary , " Magyar Banya Jog , " or the " Hungarian Mining Law, " was made use of in part . This volume is the second edition of a school textbook , which ras prepared by Dr. Bela Balkay and Dr. Imre Szeoke , and which was published by the Apollo Press ( V. , Sas -utca 13 , Budapest ) in 1909 .

Jun 1, 1931

By A. T. Iannacchione, D. G. Puglio

This Bureau of Mines study covers 25 underground mines that were active in the Upper and Lower Freeport and Lower Kittanning coalbeds in 1976. The coal ranges from low to medium volatile in rank; its primary use is for steam generation. Seven mines emit more than 100,000 cfd of methane gas; those mines are the deepest and largest producers. The methane gas content of three core samples of the Lower Kittanning coalbed was estimated by the direct method. A sample from a depth of 320 feet contained 0.5 cu cm of gas per gram, at 620 feet there was 0.8 cu cm of gas per gram, and at 1,060 feet there was 11 cu cm of gas per gram. These results suggest that methane control problems will be encountered in the future as deeper coal is mined.

Jan 1, 1979

By A. Adams

The Bureau of Mines determined the composition of the vapors liberated during thermal decomposition of aluminium nitrate nonahydrate. Small samples were heated from room temperature to 5500 C with initial heating rates from 500 to 2000 C/min. Gases were rapidly swept away from the heated chamber with Ar and subjected to immediate analysis in order to minimize reaction between the components. In addition to H20, four N-containing compounds were identified: HN03, N02, NO, and N20. Nz could not be determined in the presence of the nitrogen oxides, and at-tempted separation from the oxides led to the formation of more nitrogen. Relative amounts of each component were found to vary over a period of time; however, total amounts measured with different heating rates were reasonably constant and were typically as follows: 84.2 pct HN03, 7.1 pct N02, 4.3 pct NO, and 4.2 pct N20. HN03 and NO were determined from chemical reactions with a permanganate solution, N20 was measured with a mass spectrometer, and NO2 was measured with a spectro-photometer. Details of the methods used are described. Since NO2 and NO can readily be converted to HN03, about 96 pct of the N from the decomposition can be recovered as HN03

Jan 1, 1987

By Alla D. Mah

No experimental heat-of-formation value has been reported in the literature for cerium sesquioxide. The heat of formation of bismuth sesquioxide has not been determined in recent years, and the older value was subject to large uncertainty. Accordingly, the heats of combustion of cerium sesquioxide and bismuth metal were measured by the Federal Bureau of Mines. The heats of formation were: ?H°298.15 = -427.01 ± 0.70 kcal. /mole for cerium sesquioxide and ?H°298.15 = -137.16 ± 0.30 kcal./mole for bismuth sesquioxide. The free energy of formation was estimated for cerium sesquioxide and accurately calculated for bismuth sesquioxide. The data were compared with values in the literature.

Jan 1, 1961

By M. G. Zabetakis

This publication presents a simplified graphic method for determining the explosibility of mine atmospheres under mine-fire conditions from mine- atmosphere composition data. Sometimes it is necessary to seal part of a mine during a fire to exclude air and thus extinguish the fire. Unfortunately, liberation of methane and formation of hydrogen and carbon monoxide in the sealed area may create an ex- plosive or flammable atmosphere if enough oxygen is present to support combustion. On the other hand, the oxygen concentration may be reduced through combustion processes and the concentration of inert gases (nitrogen and carbon dioxide) increased enough to render the atmosphere within the sealed area non-explosive. Before an area is unsealed, it is extremely important to know if the sealed atmosphere contains Flammable gases in proportions that might form explosive mixtures when air is introduced. If an explosive mixture forms and the fire is rekindled, a gas explosion will result. Various experimental methods may be used to determine the explosibility of a particular mine atmosphere; however, these methods usually are impracticable in the field.

Jan 1, 1959

By Thomas E. Green

A combined solvent extract ion-spectrophotometric method for the determination of as little as 1 ppm of copper in tungsten metal or tungstic oxide has been developed and evaluated. Metallic samples are converted to tungstic oxide by treatment with hydrofluoric and nitric acids. The oxide is then dissolved in sodium hydroxide, and the copper is extracted as the colored neocuproine complex. Total elapsed time for the analysis is approximately 1-1/2 days; however, actual working time for a group of six or eight determinations is less than 4 hours. Precision at the 2-ppm level is better than 0.1 ppm.

Jan 1, 1963

By L. D. Wyant

[A convenient method for the, analysis of oil-wax mixtures has bean developed in the petroleum laboratory of the Bureau of Mines. This method has been found useful in studying the characteristics of the products obtained in petroleum refineries during the manufacture of ?wax distillate?, "foots oil", ?intermediate wax", and commercial paraffin. In this method ac-to-au is used as a selective solvent.]

Jan 1, 1924

By Mary A. Barrett

The Bureau of Mines conducted a laboratory-scale investigation of grouting mixtures containing iron or aluminum to determine the existence of health or explosion hazards, due respectively to oxygen depletion or hydrogen emission. Mixtures containing iron created an oxygen deficiency in less than 24 hours and released small amounts of hydrogen; a health hazard could occur but only under extremely unfavorable conditions. Mixtures containing aluminum released little hydrogen and consumed little oxygen; however, if improper on-site mixing yielded high local metallic aluminum concentrations, enough hydrogen might be released to produce an explosive atmosphere in a confined space.

Jan 1, 1969

By F. N. Kissell, C. D. Litton

This study ranks the factors impacting survival during a coal mine fire. It bas already been established that reducing time delays is the most important factor in saving lives. Consequently every event during afire is measured in terms d its duration, and the effectiveness d any action taken to improve survival is measured in terms d the time it saves. By ranking actions according to time saved these authors found that a comhination d actions was most effective. This combination was: • installing lifelines. • moderately decreasing air leakage and • decreasing the fire growth rate. Changing ventilation leakage alone was much less effective, as was altering the CO (carbon monoxide), sensor alarm threshold. These results confirm an earlier fault-tree study on escape from mine fires. The fault-tree study bad shown that, with the exception d delays, single factor changes have minimal impact. Significant reductions in fire fatalities only take place with multiple factor changes.

By David E. Emerson

An improved method and apparatus for determining the impurities in helium by preconcentration and subsequent analysis by mass spectrometry are described. Preconcentration of the impurities is accomplished by passing a known volume of helium, at slightly above atmospheric pressure, through a metal coil and trap assembly immersed in liquid helium. The concentrated impurities are then analyzed by mass spectrometry. This method can detect impurities in the range of 0.01 to 600 ppm with an accuracy of better than ±0.05 ppm at the 1-ppm level. One operator can analyze 15 samples in an 8-hour day.

Jan 1, 1970

By Edward F. Divers

This Bureau of Mines report describes the results of a laboratory evaluation of a mechanical dust collector (scrubber) suitable for underground coal mine applications. The scrubber was developed by the Mining Research and Development Establishment (MRDE), Burton-On-Trent, England, and tested at the Federal Bureau of Mines Pittsburgh Mining and Safety Research Center (PMSRC) as part of a technical exchange program. The 2,000-to 8,000-cfm scrubber consists of an electrically driven vane-axial fan, water sprays, a 2-inch-thick, loosely knit stainless steel wire filter panel, and a water droplet eliminator. The dust-laden airstream travels axially through the water sprays, filter panel, fan, and eliminator. Slurry water drains into a sump where a belt-driven pump recycles it back to the sprays. Fractional breakdown tests showed a maximum dust collection efficiency of 96 pct of respirable-size (less than 7 µm) coal dust at 2,000 cfm. Efficiency decreased with increasing airflow; for example, to 91 pct at 6,000 cfm. Following these tests the original wire panel was replaced with a similar but smaller panel developed at PMSRC; a marked improvement in dust collection occurred at all flow rates tested.

Jan 1, 1979

By Edward Thomas

In 1947 the Bureau of Mines, as an accident-prevention measure, decided to advocate the adoption of roof bolting (suspension roof supports) in coal mines where it appeared to be applicable. Subsequent experience has disclosed that the applicability of this support is more general than was first suspected; moreover, comparison of the accident records of mines before and after adoption of the roof-bolting method shows results that more than justify the effort and funds expended. The industry has responded enthusiastically, because roof bolting proved to be not only an accident-prevention measure but also one to increase productive efficiency. In some instances this increase in the productivity of men and machines has been almost incredible and has led many mining men to conclude that through some hocus-pocus they can now cast aside many or all of the time-proven rule of good mining practice. If this tendency is not counteracted, it could easily result in an increase of roof-fall accidents, which may outweigh the benefits of roof bolting and discredit an innovation in roof control that shows great promise of materially reducing our mining accidents. From an economic standpoint it may represent the margin between profit and loss in many mining operations. The purpose of this manuscript is not to propose an inflexible code or set of rules but to summarize the experience to date as a guide for those who have the responsibility for the installation and inspection of roof bolts. This experience consists of approximately 250 investigations of roof failure in which roof bolting was involved either directly or indirectly. It should be pointed out that many of these failures were controlled, occurring during experimental periods, and comparatively few of the accidental failures actually resulted in personal injury, yet a significant number represented potential hazards.

Jan 1, 1951