Search Documents

It is now widely accepted that horizontal stress is present nearly everywhere underground. Often it is more severe than the vertical stress. It is a major cause of roof control problems in underground mines. The AHSEM computer program contains two modules to improve mine layouts for control of horizontal stress. For development, the user specifies the orientations of the maximum horizontal stress, the entries, and the crosscuts. Angled crosscuts may be used, and the angles may be different for the right- and left-hand crosscuts. AHSEM then shows the user how the stress condition would vary as the entry and crosscut orientations are changed. The second module is for longwall mining. Severe stress concentrations can make headgate conditions hazardous when the entries are improperly oriented. AHSEM shows whether a particular longwall orientation and extraction sequence places the headgate corner in a stress concentration or in stress relief. It also estimates the magnitude of the stress concentration.

Apr 1, 2003

To facilitate compliance with title 30 CFR 75.1001-1(b), which requires testing and calibrating of trolley line automatic circuit interrupting devices at intervals not to exceed six months. Approach Calibration of a circuit breaker ideally implies the passage of the expected fault current through the sensing circuit, and observing a successful circuit interruption at the preset level within a specified time. On trolley lines, the required current may be a few thousand amperes, with maximum duration well exceeding one-tenth of a second. Any method of obtaining this calibration current Involving the trolley wire can contribute to wire sagging and other permanent damage to the haul-age system due to the high energy dissipated during the test. Also, control to assure that exactly the required level and duration of current flow is obtained implies the use of equipment which is simply not available In the ordinary mine. Under a Bureau of Mines contract, a circuit to achieve the necessary calibration pulse was conceived and built. How It Works Two prototype units were fabricated and have been field tested by MSHA technical support engineers in under-ground mines. The equipment consists of an electronics Package 20 x 24 x 8 inches and weighing 93 pounds, including a side-mounted circuit breaker, with a set of 8 foot long detachable, AWG #4/0 leads with plier-type clamps. The total lead assembly weighs 21 pounds.

Jan 1, 1981

Reduce the cost and incidence of low-back pain in underground coal mines through redesign of materials-handling tasks. Background Approximately 25 pct of all injuries in mining involve trauma to the hack. These injuries account for at least 30-40 pct of worker compensation payments made by the industry, are the leading cause of lost work days in mining, and have been estimated to cost the industry $50 million annually. It is clear that the traditional approach to reduce back injuries (i.e., training) has been largely ineffective. Thus, new approaches are necessary to control this problem. This document briefly describes methods that can be used to redesign hazardous materials-handling tasks to reduce the threat of worker injury. Approach A model for redesigning materials-handling tasks is shown in figure 1. The model outlines the sequence of steps that should be followed (and questions that should be asked) when developing new strategies for handling materials in underground coal mines. A critical examination of the current supply-handling system is the first step to developing safer materials-handling procedures. The purpose is to identify hazardous tasks that can be modified to reduce injury risk. Accident analysis (a review of past accident records) and task analy¬sis (usually a videotaped analysis of hazardous jobs or tasks) arc effective methods of distinguishing areas where job redesign is needed.

Jan 1, 1992

Although the technology involved in removing material from below the earth's surface has a long history, communication systems in underground workings are relatively new to the industry. Communication equipment did not begin appearing in underground mines until the early 1900's. Figure 1-1 shows a miner using a Western Electric standard telephone set for underground mines in 1913. These early phones were essentially the same as those used aboveground, except that they were enclosed in cast-iron boxes as protection against moisture, acid fumes, and gases. In the 1950's, the Chesapeake and Potomac Telephone Co. of West Virginia introduced a telephone set for use in explosive atmospheres that was designed around the philosophy of explosion containment. To contain an explosion within the telephone set required a 39-pound casing, which greatly limited portability. [ ] Both of these telephone sets required "pipe" or conduit, not a very practical item for a 100-squaremile coal mine. A common thread prevalent in the first 40 years of design and development is that the primary effort was placed on the telephone set. In the early 19701s, as work began on the design of modern communication systems for use in underground mine environments, the following requirements were established: 1. Must meet intrinsic safety standards .--This applies not only to coal mines, but to other explosive environments. 2. Must be compatible with the environment.--The system must with- stand dust, moisture, and corrosive conditions. 3. Must be rugged in structure.-- The system must withstand maintenance by 10-inch pliers and 4-pound hammers, as well as impact from a falling piece of roof. 4. Must be size-flexible.--Whatever is built must be sized for the small operator as well as the large companies. 5. Must be a total system in design.--The system must be intrinsically safe, including cable, power supply, and station set. 6. Must work with present telephone system.--The system should be compatible with aboveground communications already in place; it should not be the single cause of change in aboveground communications. 7. Value-added pricing.--The system should be reasonably priced so that savings created by its introduction will more than offset the installation cost.

Jan 1, 1984

To develop a simple device for rapidly determining the shearing strength and angle of Internal friction of coal and rock in situ. Approach Use a portable, permissible, hydraulically operated device in boreholes as deep as 100 feet into the rib, floor, or roof of the mine. How it Works The device, called a Borehole Shear Strength Tester (BST), is inserted Into a 3-inch-diameter borehole to the desired depth, locked Into position, and activated to shear the rock or coal in the borehole walls. The normal and shear pressures exerted by the BST, which are recorded during the test, are used to calculate the shearing strength and the angle of internal friction. The BST consists of 3 main components and several minor components. Main components are: ? A shear head with 2 shear plates that bite into the rock when normal pressure is applied. ? A hollow hydraulic jack with RW drill rods that pull the shear head when shear pressure is applied. ? A console with a hand pump and two hydraulic gages to activate the device and to indicate the pressures that apply the normal and shear faces to the shearing plates.

Jan 1, 1981

By M. L. Odenbaugh

The viscosity reduction effect of varied concentrations of leonardite (a naturally oxidized form of lignite) and leonardite-caustic on the rheological properties of a standard bentonite drilling fluid was studied and evaluated. The minimum plastic viscosity was found to occur at application rates of 4 lb of leonardite and 1.33 lb of caustic per barrel of drilling fluid. Leonardite-caustic treatment was not beneficial in treatment of salt-contaminated drilling fluids. Although filter loss rate was reduced; both yield values and gel strength were increased. Compared with other viscosity control agents) including quebracho) ligno-sulfonate) humic acids extracted from leonardite) as well as other reaction products of lignite) leonardite is less effective at low application rates but is an effective treating agent at rates of 2 Ib/bbl or more. Considering the comparable merits of the substance tested) the major factor in determining which agent to use should be based on cost consideration.

Jan 1, 1967

By K. C. Strebig

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory with a drill instrumented to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation, and an equation representing the bit performance was derived from the mathematical theory of reliability. The coefficient of friction in drilling increased with the use of additives, although the wear coefficient decreased. The decrease in wear associated with an increase in energy per unit volume consumed and the increase in penetration rate resulted in a net decrease in the cost per foot of drilling. A hypothesis explaining the effects achieved with the additives is given.

Jan 1, 1971

By Oliver Bowles

The term "stone" in its broader sense includes not only the well-known limestone, marble, granite, sandstone, and slate but also precious and semi precious stones and many minerals and rocks not included in the principal groups. Stones have long been used for structural and ornamental purposes. To be so used, they must be cut to various shapes and sizes, and some must be polished to bring out their inherent attractiveness.

Jan 1, 1958

Develop a safer, more effective, and more efficient method to control fires in abandoned coal mines and waste banks. Maintain the costs of this new method at less than or comparable to conventional AMI fire control methods. How It Works Cryogenic extinguishment of subsurface fires is a method of heat transfer. Bureau-designed injection equipment produces a pumpable slurry of liquid nitrogen and solid particles of carbon dioxide. Liquid or gaseous carbon dioxide from a pressurized tank flows to a bell-shaped nozzle where the change in pressure causes the carbon dioxide to form a granular snow. The solid carbon dioxide is mixed with liquid nitrogen. A jet pump is used to move the slurry through the delivery lines and into a simple injection probe. At injection, the nitrogen vaporizes and the carbon dioxide sublimes. This phase change produces a cold gas (-180° C) that, as it expands and moves in all directions, removes heat and also displaces oxygen. This combined process inhibits the combustion process and lowers the temperature below the reignition point. When the liquid nitrogen and solid carbon dioxide are converted to gases, the expanding gas acts like a piston, forcing warm air out of the porous bed, Although smoke and hot gases arc forced from the burning coal, generally there is no significant increase in the odor associated with burning coal.

Jan 1, 1992

Develop a simple and economical technique for determining the absolute stresses and the change of stress on the surface of roofs, floors, or walls in miners. Approach Use a commercially-available, permissible, Whittemore-type gage to determine the stress at the surface of a mine opening and to monitor any stress changes that might take place. How It Works The following equipment is used: ? One steel templet (for laying out a 60° rosette on the: rock surface). See first photograph. ? One 3/8-inch rock drill bit for drilling holes for the rosette pins. ? Six stainless-steel rosette pins. ? One Whittemore-type mechanical strain gage. ? One drill (not shown). ? Epoxy for cementing the rosette pins. ? Tape to hold the pins while the epoxy sets. The following procedure is used to determine the absolute stress on the rock surface. 1) Spot the location of the rosette pins with the templet. 2) Drill the pin holes and set the pins with epoxy cement. 3) Measure and record the distance between the pins across three diameters of the rosette with a 10-inch Whittemore-type gage. See diagram. 4) Drill a 1 1/2-inch diameter hole in the center of the

Jan 1, 1981

By Christopher Mark, Anthony T. Iannacchione

Falls of ground continue to be one of the most serious causes of injury to U.S. miners. Of the 256 fatal injuries that occurred in mining between 1996 and 1998, 59 (23%) were caused by falls of ground (Table 23.1). Falls of ground affect some sectors of the mining industry more severely than others. For instance, nearly 40% of the 98 coal mine fatalities between 1996 and 1998 were caused by falls of ground. Underground miners are at much greater risk than surface miners. Nearly half (45 out of 101) of underground mine fatalities were attributed to roof, rib, and face falls, while only 6% of the 155 surface fatalities were caused by falls of highwalls or slopes. The goal of this chapter is to provide guidance to safety professionals tasked with preventing ground fall injuries. This chapter combines an analysis of the Mine Safety and Health Administration's (MS HA) accident and injury data with a survey of industry "best practices" to safeguard miners from ground falls. Ultimately, this approach can help to form the basis of a sound, proactive ground control program for the mining industry. SOURCES OF DATA All the injury data examined in this study were derived from MSHA's fatal investigation reports and the MSHA accident database. Because falls of ground often result in serious injury, MSHA "Fatalgrams" and fatal investigation reports provide a useful snapshot of ground control issues in the mining industry. These reports are available to the public (on the M FHA Web site at www.msha.gov). Fatalgrams, are one-page summaries that are usually published within a month of an accident. They contain very basic information about the accident with a graphic and a short section on relevant best practices. Fatal investigation reports are the official accident investigation reports filed by MSHA personnel. These reports contain general information about the mine, a, description of the accident, physical factors involved in the accident, a conclusion, and enforcement actions, Enforcement actions typically identify citations and discuss violations to the Federal Mining Law. MSHA also maintains comprehensive statistical data on the mining industry's accident and injury record. The law requires that mines file a report on every reportable accident that occurs, containing information on the accident's location, severity, classification, activity, and nature of injury A short narrative is generally included as well. Accident reports can be searched by many of the above fields.

By Joseph Cervik, Maurice Deul, Albert Sainato

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pct; reductions of 38 to 79 pct were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No. 3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

Provide an accurate, reliable means for determining when a sealed mine or mine section can be safely reopened after a fire. Approach The Bureau of Mines performed a research investigation that resulted in the development of a mathematical formula for deriving a quantity, called RATIO, which can be used to define when a sealed mine or mine section has returned to safe recovery conditions after a fire. Research Results There were two major results from this Bureau research. Over a period of several years, the Bureau of Mines conducted six experiments at its Bruceton Experimental Mine in Pennsylvania. The experiments involved sealing the mine after several tons of piled coal had been allowed to burn continuously for 2 to 3 days. Although gas data obtained during the experiments revealed nothing significant, measured smoke particle levels were found to correlate with the stages of combustion and temperatures of the smoldering coal pile. Moreover, it was found that no smoke particles are produced when high-temperature smoldering exists deep within the mass of the coal pile since the smoke particles are filtered by the coal surrounding the hot region. Smoke is emitted into the mine atmosphere only if combustion is occurring near exposed surfaces. As suggested by these findings, any decision to recover a sealed mine area based primarily upon the absence of smoke particles is not a wise derision.

Jan 1, 1988

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983

By A. N. Styler

As part of its water-jet assisted rock cutting research, the Bureau of Mines has initiated a study into the mechanism of rock fragmentation by water-jet-assisted mechanical tools. The objective of this research is to increase coal extraction efficiency by seeking an improved understanding of the synergistic relationship between mechanical cutters and water jets, enabling the design of more effective cutterheads. Rock chips collected during laboratory traverse speed jet-assisted cutting tests were analyzed with respect to the size distribution of the chips and the forces measured during cutting. As the water-jet pressure was increased, the size distribution of the product became coarser with V-face type cutting tools producing less fine material than conical cutting tools. Fracture mechanics theory accounted for less than 10 pet of the energy consumed during fragmentation of the rock. The energy consumed by processes other than rock breakage decreased with the use of water jets and increasing advance rate.

Jan 1, 1987

By James R. Welty

Heat content values were experimentally determined for yttrium metal between temperatures of 400° and 1,300° K and for iron pentacarbonyl between 301° and 380° K. The drop technique was used; that is, a sample of material sealed in a protective capsule was heated to 3 desired temperature in a furnace and then dropped into an ice calorimeter. A revised technique for determining heat content values from calorimetric data is described. Heat content and corresponding entropy-increment data above a reference temperature of 298.15° K are presented in tabular form. Equations for heat content and heat capacity as functions of temperature were derived for each substance. These equations are [Y (c): HT-H298.15 = 1.2041T 1 3.393 x 10-3T2- 0.4176 x 10' T"1 + 739.9 cal/mole Cp = 1.2041 + 6.786 x 10-3T + 0.4176 x 106-T-2 cal/deg mole Fe (CO) E, (1) : HT - H298.15 = 55.636T - 16,588 cal/mole Cp = 55.636 cal/deg mole]

Jan 1, 1963

By Karl C. Dean

The Bureau of Mines studied the precipitation of copper from dilute acidic sulfate solutions using shredded automobile scrap in a rotary drum. The tests established that the scrap in the rotary drum precipitated copper faster and more completely than shredded, detinned, tinplate scrap in a launder, with comparable iron consumption. Although power is required to rotate the drum, the faster precipitation and continuous recovery of cement copper are advantages of the tumbler method. Cost evaluation indicates that the rotary drum method, which uses relatively low-cost and readily available shredded automobile scrap, is competitive with the launder method, which uses relatively high-cost shredded tinplate scrap or detinned shredded cans.

Jan 1, 1968

Compare the dust control efficiency and bit life of surface coal mine drills using standard water injection and water injection with water separation. Approach A research study was conducted to determine if a water separation technique affects wet suppression dust control. Dust control efficiency and bit life of surface coal mine drills were compared during tests using both standard water injection (wet drill bit cutting) and water injection with water separation (dry drill bit cutting). Background Surface coal mine blast hole drills typically generate a substantial amount of dust during the drilling cycle. One method used to control this dust is the injection of water into the bailing air. This is known as wet suppression.

Jan 1, 1988

By S. A. Gustavson, H. E. Olund

This report has been prepared to review the history of the Premium Price Plan for copper, lead, and zinc, which was in operation from February 1, 1942, to June 30, 1947. It includes various charts and tables comparing costs and production data, and data on exploration premiums that were included in the Plan during the last year of its operation.

Jan 1, 1950

By Donald M. Hausen

Diamond-bit performance and cost data accumulated by the Bureau of Mines in core-drilling schists reveal significant trends of economic interest. Low-quality, small-size drill bort were the most economical. The percentage of core recovery, type and size of bit, and bit matrix are also correlated with bit performance and costs. Detailed analyses of the factors affecting diamond-bit performances and costs are assessed in the tables, graphs, and discussion.

Jan 1, 1956